| Age | Commit message (Collapse) | Author |
|---|
|
If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.
This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current flow: Set TX BD ready, and then set "INT" and "PINS" bit to
enable tx interrupt generation and crc checksum.
There has potential issue like as:
CPU fec uDMA
Set tx ready bit
uDMA start the BD transmission
Set "INT" bit
Set "PINS" bit
...
Above situation cause fec tx interrupt lost and fec MAC don't do
CRC checksum. The patch fix the potential issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <Frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If napi is left enabled after a failed attempt to bring the interface
up, we BUG:
fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
libphy: PHY fixed-0:00 not found
fec 2188000.ethernet eth0: could not attach to PHY
------------[ cut here ]------------
kernel BUG at include/linux/netdevice.h:502!
Internal error: Oops - BUG: 0 [#1] SMP ARM
...
PC is at fec_enet_open+0x4d0/0x500
LR is at __dev_open+0xa4/0xfc
Only enable napi after we are past all the failure paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to keep DT compatibility we need to revert this, otherwise the original
dts files will no longer work with this driver change.
This reverts commit 7a399e3a2e05bc580a78ea72371b3896827f72e1.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not assume that the PHY reset is always active low.
Retrieve this information from the device tree instead, so that the PHY reset
can work on both cases.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_tx_timestamp(skb) should be called _before_ TX completion
has a chance to trigger, otherwise it is too late and we access
freed memory.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: de5fb0a05348 ("net: fec: put tx to napi poll function to fix dead lock")
Cc: Frank Li <Frank.Li@freescale.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 031916568a1aa2ef1809f86d26f0bcfa215ff5c0 worked around
errata ERR006358, but comment contains duplicated lines, impairing
the readability. Remove them.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On tx submit the driver always dma_map_single() FEC_ENET_TX_FRSIZE (=2048)
bytes. This works because we don't overwrite any memory after the data buffer,
we remove it from cache if it was there. So we hurt performace in case the
mapping of a smaller area makes a difference.
There is also a bug: If the data area starts shortly before the end of
RAM say 0xc7fffa10 and the RAM ends at 0xc8000000 then we have enough
space to fit the data area (according to skb->len) but we would map beyond
end of ram if we are using 2048. In v2.6.31 (against which kernel this patch
made) there is the following check in dma_cache_maint():
|BUG_ON(!virt_addr_valid(start) || !virt_addr_valid(start + size - 1));
Since the area starting at 0xc8000000 is no longer virt_addr_valid() we
BUG() during dma_map_single(). The BUG() statement was removed in v3.5-rc1 as
per 2dc6a016 ("ARM: dma-mapping: use asm-generic/dma-mapping-common.h").
This patch was tested on v2.6.31 and then forward-ported and compile
tested only against the net tree. I think it is still worth fixing
mainline even after the BUG() statement is gone.
Tested-by: Fugang Duan <B38611@freescale.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is untested.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The driver fails to check the results of DMA mapping and results in
the following warning: (with kernel config "CONFIG_DMA_API_DEBUG" enable)
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:937 check_unmap+0x43c/0x7d8()
fec 2188000.ethernet: DMA-API: device driver failed to check map
error[device address=0x00000000383a8040] [size=2048 bytes] [mapped as single]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.17-16827-g9cdb0ba-dirty #188
[<80013c4c>] (unwind_backtrace+0x0/0xf8) from [<80011704>] (show_stack+0x10/0x14)
[<80011704>] (show_stack+0x10/0x14) from [<80025614>] (warn_slowpath_common+0x4c/0x6c)
[<80025614>] (warn_slowpath_common+0x4c/0x6c) from [<800256c8>] (warn_slowpath_fmt+0x30/0x40)
[<800256c8>] (warn_slowpath_fmt+0x30/0x40) from [<8026bfdc>] (check_unmap+0x43c/0x7d8)
[<8026bfdc>] (check_unmap+0x43c/0x7d8) from [<8026c584>] (debug_dma_unmap_page+0x6c/0x78)
[<8026c584>] (debug_dma_unmap_page+0x6c/0x78) from [<8038049c>] (fec_enet_rx_napi+0x254/0x8a8)
[<8038049c>] (fec_enet_rx_napi+0x254/0x8a8) from [<804dc8c0>] (net_rx_action+0x94/0x160)
[<804dc8c0>] (net_rx_action+0x94/0x160) from [<8002c758>] (__do_softirq+0xe8/0x1d0)
[<8002c758>] (__do_softirq+0xe8/0x1d0) from [<8002c8e8>] (do_softirq+0x4c/0x58)
[<8002c8e8>] (do_softirq+0x4c/0x58) from [<8002cb50>] (irq_exit+0x90/0xc8)
[<8002cb50>] (irq_exit+0x90/0xc8) from [<8000ea88>] (handle_IRQ+0x3c/0x94)
[<8000ea88>] (handle_IRQ+0x3c/0x94) from [<8000855c>] (gic_handle_irq+0x28/0x5c)
[<8000855c>] (gic_handle_irq+0x28/0x5c) from [<8000de00>] (__irq_svc+0x40/0x50)
Exception stack(0x815a5f38 to 0x815a5f80)
5f20: 815a5f80 3b9aca00
5f40: 0fe52383 00000002 0dd8950e 00000002 81e7b080 00000000 00000000 815ac4d8
5f60: 806032ec 00000000 00000017 815a5f80 80059028 8041fc4c 60000013 ffffffff
[<8000de00>] (__irq_svc+0x40/0x50) from [<8041fc4c>] (cpuidle_enter_state+0x50/0xf0)
[<8041fc4c>] (cpuidle_enter_state+0x50/0xf0) from [<8041fd94>] (cpuidle_idle_call+0xa8/0x14c)
[<8041fd94>] (cpuidle_idle_call+0xa8/0x14c) from [<8000edac>] (arch_cpu_idle+0x10/0x4c)
[<8000edac>] (arch_cpu_idle+0x10/0x4c) from [<800582f8>] (cpu_startup_entry+0x60/0x130)
[<800582f8>] (cpu_startup_entry+0x60/0x130) from [<80bc7a48>] (start_kernel+0x2d0/0x328)
[<80bc7a48>] (start_kernel+0x2d0/0x328) from [<10008074>] (0x10008074)
---[ end trace c6edec32436e0042 ]---
Because dma-debug add new interfaces to debug dma mapping errors, pls refer
to: http://lwn.net/Articles/516640/
After dma mapping, it must call dma_mapping_error() to check mapping error,
otherwise the map_err_type alway is MAP_ERR_NOT_CHECKED, check_unmap() define
the mapping is not checked and dump the error msg. So,add dma_mapping_error()
checking to fix the WARNING
And RX DMA buffers are used repeatedly and the driver copies it into an skb,
fec_enet_rx() should not map or unmap, use dma_sync_single_for_cpu()/dma_sync_single_for_device()
instead of dma_map_single()/dma_unmap_single().
There have another potential issue: fec_enet_rx() passes the DMA address to __va().
Physical and DMA addresses are *not* the same thing. They may differ if the device
is behind an IOMMU or bounce buffering was required, or just because there is a fixed
offset between the device and host physical addresses. Also fix it in this patch.
=============================================
V2: add net_ratelimit() to limit map err message.
use dma_sync_single_for_cpu() instead of dma_map_single().
fix the issue that pass DMA addresses to __va() to get virture address.
V1: initial send
=============================================
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/freescale/fec_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug: error to get the previous BD entry. When the current BD
is the first BD, the previous BD entry must be the last BD,
not "bdp - 1" in current logic.
V4:
* Optimize fec_enet_get_nextdesc() for code clean.
Replace "ex_new_bd - ring_size" with "ex_base".
Replace "new_bd - ring_size" with "base".
V3:
* Restore the API name because David suggest to use fec_enet_
prefix for all function in fec driver.
So, change next_bd() -> fec_enet_get_nextdesc()
change pre_bd() -> fec_enet_get_prevdesc()
* Reduce the two APIs parameters for easy to call.
V2:
* Add tx_ring_size and rx_ring_size to struct fec_enet_private.
* Replace api fec_enet_get_nextdesc() with next_bd().
Replace api fec_enet_get_prevdesc() with pre_bd().
* Move all ring size check logic to next_bd() and pre_bd(), which
simplifies the code redundancy.
V1:
* Add BD ring size check to get the previous BD entry in correctly.
Reviewed-by: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <frank.li@freescale.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit dc975382 "net: fec: add napi support to improve proformance"
converted the fec driver to the napi model. However, that commit
forgot to remove the call to skb_defer_rx_timestamp which is only
needed in non-napi drivers.
(The function napi_gro_receive eventually calls netif_receive_skb,
which in turn calls skb_defer_rx_timestamp.)
This patch should also be applied to the 3.9 and 3.10 kernels.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My static checker complains that on some arches unsigned longs can be 8
characters which is larger than the buffer is only 6 chars.
Additionally, Ben Hutchings points out that the buffer actually holds
big endian data and the buffer we are reading from is CPU endian.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using a custom 'FEC_NAPI_WEIGHT', just use the generic
'NAPI_POLL_WEIGHT' definition instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge net into net-next to setup some infrastructure Eric
Dumazet needs for usbnet changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't test for having link and let hardware deal with this situation.
Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MODULE_ALIAS, so that auto module loading can work.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using devm_request_irq() can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As devm_ioremap_resource() is used, there is no need to explicitely check the
return value from platform_get_resource(), as this is something that
devm_ioremap_resource() takes care by itself.
Also, place platform_get_resource() prior to devm_ioremap_resource() for
better code readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clk_ptp should also be enabled in fec_resume() and disabled in fec_suspend().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On fec_probe the clocks are enabled in the following order:
clk_ahb -> clk_ipg -> clk_enet_out -> clk_ptp
, so in the error and remove paths we should disabled them in the opposite
order.
Also fix the order in the suspend/resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clk_enet_out and clk_ptp are optional clocks, so we should not enable/disable
them unconditionally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables the driver to take advantage of the FEC VLAN
indicator to improve performance.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 38ae92d "fec: Add support for reading
RMON registers" causes the imx6Q to crash.
This fixes it by only enabling the RMON registers, the
registers are already cleared by the MAC being reset.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx_bytes field was not being updated so the
network card statistics showed 0.0B transmitted.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setup the multicast list of the net_device instead of
clearing it blindly. This restores the multicast groups
in case of a link down/up event or when resuming from
suspend.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ethtool operation to read RMON registers.
Tested against net-next on i.MX28.
v2: make conditional on #ifndef CONFIG_M5272
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commits 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration) and
baa70a5c (net: fec: enable pause frame to improve rx prefomance for 1G
network) introduced functionality into the FEC driver which is not
supported on MCF5272. The registers used to implement this functionality
do not exist on MCF5272. Since register defines for MCF5272 are separate
from register defines for other chips, building images for MCF5272 fails
as follows.
fec_main.c: In function 'fec_restart':
fec_main.c:520:8: error: 'FEC_RACC' undeclared (first use in this function)
fec_main.c:585:3: error: 'FEC_R_FIFO_RSEM' undeclared (first use in this function)
fec_main.c:586:3: error: 'FEC_R_FIFO_RSFL' undeclared (first use in this function)
fec_main.c:587:3: error: 'FEC_R_FIFO_RAEM' undeclared (first use in this function)
fec_main.c:588:3: error: 'FEC_R_FIFO_RAFL' undeclared (first use in this function)
fec_main.c:591:3: error: 'FEC_OPD' undeclared (first use in this function)
Adding the missing register defines is not an option, since the registers
do not exist on MCF5272. Disable the added functionality for MCF5272 builds.
Cc: Frank Li <Frank.Li@freescale.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ethtool operation to restart autonegotiation via the PHY.
Tested on i.MX28EVK.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 75096579c3ac ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: netdev@vger.kernel.org
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passing pdev in fec_ptp_init() is enough, since we can get ndev locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to save power, let's disable the regulator in the suspend function and
enable it in resume.
Tested on a mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During probe the clocks are enabled prior than the acquiring the interrupts.
In the remove function we need to do the opposite: first remove the interrupts
and then disable the clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of error during probe, disable the PHY regulator.
Do the same in fec_drv_remove().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when fec_enet_init fails it jumps to 'failed_init' error path, which
will attemp to free the interrupts.
This is wrong because at this point the interrupts have not even been acquired.
Swap failed_init/failed_irq to fix the error path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().
This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
