Merge remote-tracking branch 'tty/tty-next'

39 files changed, 240 insertions, 417 deletions

diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt
index 44152261e5c5..8d63f1da07aa 100644
--- a/Documentation/devicetree/bindings/serial/mtk-uart.txt
+++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt
@@ -14,7 +14,14 @@ Required properties:
 
 - interrupts: A single interrupt specifier.
 
-- clocks: Clock driving the hardware.
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names:
+  - "baud": The clock the baudrate is derived from
+  - "bus": The bus clock for register accesses (optional)
+
+For compatibility with older device trees an unnamed clock is used for the
+baud clock if the baudclk does not exist. Do not use this for new designs.
 
 Example:
 
@@ -22,5 +29,6 @@ Example:
 		compatible = "mediatek,mt6589-uart", "mediatek,mt6577-uart";
 		reg = <0x11006000 0x400>;
 		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&uart_clk>;
+		clocks = <&uart_clk>, <&bus_clk>;
+		clock-names = "baud", "bus";
 	};
diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt
index f0c39261c5d4..67e2a0aeb042 100644
--- a/Documentation/devicetree/bindings/serial/sirf-uart.txt
+++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt
@@ -2,8 +2,7 @@
 
 Required properties:
 - compatible : Should be "sirf,prima2-uart", "sirf, prima2-usp-uart",
-		"sirf,atlas7-uart" or "sirf,atlas7-bt-uart" which means
-		uart located in BT module and used for BT.
+		"sirf,atlas7-uart" or "sirf,atlas7-usp-uart".
 - reg : Offset and length of the register set for the device
 - interrupts : Should contain uart interrupt
 - fifosize : Should define hardware rx/tx fifo size
@@ -33,15 +32,3 @@ usp@b0090000 {
 	rts-gpios = <&gpio 15 0>;
 	cts-gpios = <&gpio 46 0>;
 };
-
-for uart use in BT module,
-uart6: uart@11000000 {
-	cell-index = <6>;
-	compatible = "sirf,atlas7-bt-uart", "sirf,atlas7-uart";
-	reg = <0x11000000 0x1000>;
-	interrupts = <0 100 0>;
-	clocks = <&clks 138>, <&clks 140>, <&clks 141>;
-	clock-names = "uart", "general", "noc";
-	fifosize = <128>;
-	status = "disabled";
-}
diff --git a/arch/alpha/include/asm/serial.h b/arch/alpha/include/asm/serial.h
index 9d263e8d8ccc..22909b83f473 100644
--- a/arch/alpha/include/asm/serial.h
+++ b/arch/alpha/include/asm/serial.h
@@ -13,7 +13,7 @@
 #define BASE_BAUD ( 1843200 / 16 )
 
 /* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
+#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
 #define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
 #else
diff --git a/arch/arm/common/edma.c b/arch/arm/common/edma.c
index 5662a872689b..873dbfcc7dc9 100644
--- a/arch/arm/common/edma.c
+++ b/arch/arm/common/edma.c
@@ -1350,6 +1350,9 @@ void edma_stop(unsigned channel)
 		edma_shadow0_write_array(ctlr, SH_SECR, j, mask);
 		edma_write_array(ctlr, EDMA_EMCR, j, mask);
 
+		/* clear possibly pending completion interrupt */
+		edma_shadow0_write_array(ctlr, SH_ICR, j, mask);
+
 		pr_debug("EDMA: EER%d %08x\n", j,
 				edma_shadow0_read_array(ctlr, SH_EER, j));
 
diff --git a/arch/blackfin/include/asm/bfin_serial.h b/arch/blackfin/include/asm/bfin_serial.h
index d00d732784b1..b550ada7321b 100644
--- a/arch/blackfin/include/asm/bfin_serial.h
+++ b/arch/blackfin/include/asm/bfin_serial.h
@@ -22,9 +22,9 @@
     defined(CONFIG_BFIN_UART2_CTSRTS) || \
     defined(CONFIG_BFIN_UART3_CTSRTS)
 # if defined(BFIN_UART_BF54X_STYLE) || defined(BFIN_UART_BF60X_STYLE)
-#  define CONFIG_SERIAL_BFIN_HARD_CTSRTS
+#  define SERIAL_BFIN_HARD_CTSRTS
 # else
-#  define CONFIG_SERIAL_BFIN_CTSRTS
+#  define SERIAL_BFIN_CTSRTS
 # endif
 #endif
 
@@ -50,8 +50,8 @@ struct bfin_serial_port {
 #elif ANOMALY_05000363
 	unsigned int anomaly_threshold;
 #endif
-#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+#if defined(SERIAL_BFIN_CTSRTS) || \
+	defined(SERIAL_BFIN_HARD_CTSRTS)
 	int cts_pin;
 	int rts_pin;
 #endif
diff --git a/arch/m68k/include/asm/serial.h b/arch/m68k/include/asm/serial.h
index 7267536adbcc..06d0cb19b4e1 100644
--- a/arch/m68k/include/asm/serial.h
+++ b/arch/m68k/include/asm/serial.h
@@ -17,7 +17,7 @@
 #define BASE_BAUD ( 1843200 / 16 )
 
 /* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
+#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
 #define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
 #else
diff --git a/arch/mn10300/include/asm/serial.h b/arch/mn10300/include/asm/serial.h
index 23a799293599..c1990218f18c 100644
--- a/arch/mn10300/include/asm/serial.h
+++ b/arch/mn10300/include/asm/serial.h
@@ -13,7 +13,7 @@
 #define _ASM_SERIAL_H
 
 /* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
+#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
 #define STD_COM_FLAGS	(ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
 #define STD_COM4_FLAGS	(ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
 #else
@@ -21,7 +21,7 @@
 #define STD_COM4_FLAGS	ASYNC_BOOT_AUTOCONF
 #endif
 
-#ifdef CONFIG_SERIAL_MANY_PORTS
+#ifdef CONFIG_SERIAL_8250_MANY_PORTS
 #define FOURPORT_FLAGS	ASYNC_FOURPORT
 #define ACCENT_FLAGS	0
 #define BOCA_FLAGS	0
diff --git a/arch/x86/include/asm/serial.h b/arch/x86/include/asm/serial.h
index 8378b8c9109c..bb658211edad 100644
--- a/arch/x86/include/asm/serial.h
+++ b/arch/x86/include/asm/serial.h
@@ -11,7 +11,7 @@
 #define BASE_BAUD (1843200/16)
 
 /* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
+#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
 # define STD_COMX_FLAGS	(UPF_BOOT_AUTOCONF |	UPF_SKIP_TEST	| UPF_AUTO_IRQ)
 # define STD_COM4_FLAGS	(UPF_BOOT_AUTOCONF |	0		| UPF_AUTO_IRQ)
 #else
diff --git a/drivers/dma/edma.c b/drivers/dma/edma.c
index bf09db7ca9ee..88853af69489 100644
--- a/drivers/dma/edma.c
+++ b/drivers/dma/edma.c
@@ -300,8 +300,7 @@ static int edma_dma_pause(struct dma_chan *chan)
 {
 	struct edma_chan *echan = to_edma_chan(chan);
 
-	/* Pause/Resume only allowed with cyclic mode */
-	if (!echan->edesc || !echan->edesc->cyclic)
+	if (!echan->edesc)
 		return -EINVAL;
 
 	edma_pause(echan->ch_num);
@@ -312,10 +311,6 @@ static int edma_dma_resume(struct dma_chan *chan)
 {
 	struct edma_chan *echan = to_edma_chan(chan);
 
-	/* Pause/Resume only allowed with cyclic mode */
-	if (!echan->edesc->cyclic)
-		return -EINVAL;
-
 	edma_resume(echan->ch_num);
 	return 0;
 }
diff --git a/drivers/input/serio/serport.c b/drivers/input/serio/serport.c
index 69175b825346..9c927d35c1f5 100644
--- a/drivers/input/serio/serport.c
+++ b/drivers/input/serio/serport.c
@@ -167,7 +167,6 @@ static ssize_t serport_ldisc_read(struct tty_struct * tty, struct file * file, u
 {
 	struct serport *serport = (struct serport*) tty->disc_data;
 	struct serio *serio;
-	char name[64];
 
 	if (test_and_set_bit(SERPORT_BUSY, &serport->flags))
 		return -EBUSY;
@@ -177,7 +176,7 @@ static ssize_t serport_ldisc_read(struct tty_struct * tty, struct file * file, u
 		return -ENOMEM;
 
 	strlcpy(serio->name, "Serial port", sizeof(serio->name));
-	snprintf(serio->phys, sizeof(serio->phys), "%s/serio0", tty_name(tty, name));
+	snprintf(serio->phys, sizeof(serio->phys), "%s/serio0", tty_name(tty));
 	serio->id = serport->id;
 	serio->id.type = SERIO_RS232;
 	serio->write = serport_serio_write;
@@ -187,7 +186,7 @@ static ssize_t serport_ldisc_read(struct tty_struct * tty, struct file * file, u
 	serio->dev.parent = tty->dev;
 
 	serio_register_port(serport->serio);
-	printk(KERN_INFO "serio: Serial port %s\n", tty_name(tty, name));
+	printk(KERN_INFO "serio: Serial port %s\n", tty_name(tty));
 
 	wait_event_interruptible(serport->wait, test_bit(SERPORT_DEAD, &serport->flags));
 	serio_unregister_port(serport->serio);
diff --git a/drivers/tty/amiserial.c b/drivers/tty/amiserial.c
index b2d760055952..894d3a84e285 100644
--- a/drivers/tty/amiserial.c
+++ b/drivers/tty/amiserial.c
@@ -966,9 +966,7 @@ static void rs_throttle(struct tty_struct * tty)
 	struct serial_state *info = tty->driver_data;
 	unsigned long flags;
 #ifdef SERIAL_DEBUG_THROTTLE
-	char	buf[64];
-
-	printk("throttle %s: %d....\n", tty_name(tty, buf),
+	printk("throttle %s: %d....\n", tty_name(tty),
 	       tty->ldisc.chars_in_buffer(tty));
 #endif
 
@@ -991,9 +989,7 @@ static void rs_unthrottle(struct tty_struct * tty)
 	struct serial_state *info = tty->driver_data;
 	unsigned long flags;
 #ifdef SERIAL_DEBUG_THROTTLE
-	char	buf[64];
-
-	printk("unthrottle %s: %d....\n", tty_name(tty, buf),
+	printk("unthrottle %s: %d....\n", tty_name(tty),
 	       tty->ldisc.chars_in_buffer(tty));
 #endif
 
diff --git a/drivers/tty/cyclades.c b/drivers/tty/cyclades.c
index fd66f57390d0..87f6578c6f4a 100644
--- a/drivers/tty/cyclades.c
+++ b/drivers/tty/cyclades.c
@@ -2861,9 +2861,7 @@ static void cy_throttle(struct tty_struct *tty)
 	unsigned long flags;
 
 #ifdef CY_DEBUG_THROTTLE
-	char buf[64];
-
-	printk(KERN_DEBUG "cyc:throttle %s: %ld...ttyC%d\n", tty_name(tty, buf),
+	printk(KERN_DEBUG "cyc:throttle %s: %ld...ttyC%d\n", tty_name(tty),
 			tty->ldisc.chars_in_buffer(tty), info->line);
 #endif
 
@@ -2902,10 +2900,8 @@ static void cy_unthrottle(struct tty_struct *tty)
 	unsigned long flags;
 
 #ifdef CY_DEBUG_THROTTLE
-	char buf[64];
-
 	printk(KERN_DEBUG "cyc:unthrottle %s: %ld...ttyC%d\n",
-		tty_name(tty, buf), tty_chars_in_buffer(tty), info->line);
+		tty_name(tty), tty_chars_in_buffer(tty), info->line);
 #endif
 
 	if (serial_paranoia_check(info, tty->name, "cy_unthrottle"))
diff --git a/drivers/tty/n_gsm.c b/drivers/tty/n_gsm.c
index 2c34c3249972..c408689a85a9 100644
--- a/drivers/tty/n_gsm.c
+++ b/drivers/tty/n_gsm.c
@@ -2274,7 +2274,6 @@ static void gsmld_receive_buf(struct tty_struct *tty, const unsigned char *cp,
 	const unsigned char *dp;
 	char *f;
 	int i;
-	char buf[64];
 	char flags = TTY_NORMAL;
 
 	if (debug & 4)
@@ -2296,7 +2295,7 @@ static void gsmld_receive_buf(struct tty_struct *tty, const unsigned char *cp,
 			break;
 		default:
 			WARN_ONCE(1, "%s: unknown flag %d\n",
-			       tty_name(tty, buf), flags);
+			       tty_name(tty), flags);
 			break;
 		}
 	}
diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c
index cc57a3a6b02b..85e46422311c 100644
--- a/drivers/tty/n_tty.c
+++ b/drivers/tty/n_tty.c
@@ -1179,13 +1179,12 @@ static void n_tty_receive_break(struct tty_struct *tty)
 static void n_tty_receive_overrun(struct tty_struct *tty)
 {
 	struct n_tty_data *ldata = tty->disc_data;
-	char buf[64];
 
 	ldata->num_overrun++;
 	if (time_after(jiffies, ldata->overrun_time + HZ) ||
 			time_after(ldata->overrun_time, jiffies)) {
 		printk(KERN_WARNING "%s: %d input overrun(s)\n",
-			tty_name(tty, buf),
+			tty_name(tty),
 			ldata->num_overrun);
 		ldata->overrun_time = jiffies;
 		ldata->num_overrun = 0;
@@ -1460,8 +1459,6 @@ static void n_tty_receive_char_closing(struct tty_struct *tty, unsigned char c)
 static void
 n_tty_receive_char_flagged(struct tty_struct *tty, unsigned char c, char flag)
 {
-	char buf[64];
-
 	switch (flag) {
 	case TTY_BREAK:
 		n_tty_receive_break(tty);
@@ -1475,7 +1472,7 @@ n_tty_receive_char_flagged(struct tty_struct *tty, unsigned char c, char flag)
 		break;
 	default:
 		printk(KERN_ERR "%s: unknown flag %d\n",
-		       tty_name(tty, buf), flag);
+		       tty_name(tty), flag);
 		break;
 	}
 }
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index 4506e405c8f3..01cecd52b909 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -85,19 +85,6 @@ static unsigned int skip_txen_test; /* force skip of txen test at init time */
 #define BOTH_EMPTY 	(UART_LSR_TEMT | UART_LSR_THRE)
 
 
-#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
-#define CONFIG_SERIAL_DETECT_IRQ 1
-#endif
-#ifdef CONFIG_SERIAL_8250_MANY_PORTS
-#define CONFIG_SERIAL_MANY_PORTS 1
-#endif
-
-/*
- * HUB6 is always on.  This will be removed once the header
- * files have been cleaned.
- */
-#define CONFIG_HUB6 1
-
 #include <asm/serial.h>
 /*
  * SERIAL_PORT_DFNS tells us about built-in ports that have no
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index 7a11fac775c4..8eb3876563f1 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -34,6 +34,7 @@
 struct mtk8250_data {
 	int			line;
 	struct clk		*uart_clk;
+	struct clk		*bus_clk;
 };
 
 static void
@@ -115,6 +116,36 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
 		tty_termios_encode_baud_rate(termios, baud, baud);
 }
 
+static int mtk8250_runtime_suspend(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(data->uart_clk);
+	clk_disable_unprepare(data->bus_clk);
+
+	return 0;
+}
+
+static int mtk8250_runtime_resume(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+	int err;
+
+	err = clk_prepare_enable(data->uart_clk);
+	if (err) {
+		dev_warn(dev, "Can't enable clock\n");
+		return err;
+	}
+
+	err = clk_prepare_enable(data->bus_clk);
+	if (err) {
+		dev_warn(dev, "Can't enable bus clock\n");
+		return err;
+	}
+
+	return 0;
+}
+
 static void
 mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
 {
@@ -130,22 +161,24 @@ mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
 static int mtk8250_probe_of(struct platform_device *pdev, struct uart_port *p,
 			   struct mtk8250_data *data)
 {
-	int err;
-	struct device_node *np = pdev->dev.of_node;
-
-	data->uart_clk = of_clk_get(np, 0);
+	data->uart_clk = devm_clk_get(&pdev->dev, "baud");
 	if (IS_ERR(data->uart_clk)) {
-		dev_warn(&pdev->dev, "Can't get timer clock\n");
-		return PTR_ERR(data->uart_clk);
+		/*
+		 * For compatibility with older device trees try unnamed
+		 * clk when no baud clk can be found.
+		 */
+		data->uart_clk = devm_clk_get(&pdev->dev, NULL);
+		if (IS_ERR(data->uart_clk)) {
+			dev_warn(&pdev->dev, "Can't get uart clock\n");
+			return PTR_ERR(data->uart_clk);
+		}
+
+		return 0;
 	}
 
-	err = clk_prepare_enable(data->uart_clk);
-	if (err) {
-		dev_warn(&pdev->dev, "Can't prepare clock\n");
-		clk_put(data->uart_clk);
-		return err;
-	}
-	p->uartclk = clk_get_rate(data->uart_clk);
+	data->bus_clk = devm_clk_get(&pdev->dev, "bus");
+	if (IS_ERR(data->bus_clk))
+		return PTR_ERR(data->bus_clk);
 
 	return 0;
 }
@@ -190,19 +223,24 @@ static int mtk8250_probe(struct platform_device *pdev)
 	uart.port.regshift = 2;
 	uart.port.private_data = data;
 	uart.port.set_termios = mtk8250_set_termios;
+	uart.port.uartclk = clk_get_rate(data->uart_clk);
 
 	/* Disable Rate Fix function */
 	writel(0x0, uart.port.membase +
 			(MTK_UART_RATE_FIX << uart.port.regshift));
 
-	data->line = serial8250_register_8250_port(&uart);
-	if (data->line < 0)
-		return data->line;
-
 	platform_set_drvdata(pdev, data);
 
-	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
+	if (!pm_runtime_enabled(&pdev->dev)) {
+		err = mtk8250_runtime_resume(&pdev->dev);
+		if (err)
+			return err;
+	}
+
+	data->line = serial8250_register_8250_port(&uart);
+	if (data->line < 0)
+		return data->line;
 
 	return 0;
 }
@@ -214,13 +252,13 @@ static int mtk8250_remove(struct platform_device *pdev)
 	pm_runtime_get_sync(&pdev->dev);
 
 	serial8250_unregister_port(data->line);
-	if (!IS_ERR(data->uart_clk)) {
-		clk_disable_unprepare(data->uart_clk);
-		clk_put(data->uart_clk);
-	}
 
 	pm_runtime_disable(&pdev->dev);
 	pm_runtime_put_noidle(&pdev->dev);
+
+	if (!pm_runtime_status_suspended(&pdev->dev))
+		mtk8250_runtime_suspend(&pdev->dev);
+
 	return 0;
 }
 
@@ -244,28 +282,6 @@ static int mtk8250_resume(struct device *dev)
 }
 #endif /* CONFIG_PM_SLEEP */
 
-#ifdef CONFIG_PM
-static int mtk8250_runtime_suspend(struct device *dev)
-{
-	struct mtk8250_data *data = dev_get_drvdata(dev);
-
-	if (!IS_ERR(data->uart_clk))
-		clk_disable_unprepare(data->uart_clk);
-
-	return 0;
-}
-
-static int mtk8250_runtime_resume(struct device *dev)
-{
-	struct mtk8250_data *data = dev_get_drvdata(dev);
-
-	if (!IS_ERR(data->uart_clk))
-		clk_prepare_enable(data->uart_clk);
-
-	return 0;
-}
-#endif
-
 static const struct dev_pm_ops mtk8250_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume)
 	SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume,
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index 9289999cb7c6..77c9f5aa8369 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -98,6 +98,7 @@ struct omap8250_priv {
 	struct pm_qos_request pm_qos_request;
 	struct work_struct qos_work;
 	struct uart_8250_dma omap8250_dma;
+	spinlock_t rx_dma_lock;
 };
 
 static u32 uart_read(struct uart_8250_port *up, u32 reg)
@@ -669,14 +670,21 @@ static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir);
 
 static void __dma_rx_do_complete(struct uart_8250_port *p, bool error)
 {
+	struct omap8250_priv	*priv = p->port.private_data;
 	struct uart_8250_dma    *dma = p->dma;
 	struct tty_port         *tty_port = &p->port.state->port;
 	struct dma_tx_state     state;
 	int                     count;
+	unsigned long		flags;
 
 	dma_sync_single_for_cpu(dma->rxchan->device->dev, dma->rx_addr,
 				dma->rx_size, DMA_FROM_DEVICE);
 
+	spin_lock_irqsave(&priv->rx_dma_lock, flags);
+
+	if (!dma->rx_running)
+		goto unlock;
+
 	dma->rx_running = 0;
 	dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
 	dmaengine_terminate_all(dma->rxchan);
@@ -685,6 +693,9 @@ static void __dma_rx_do_complete(struct uart_8250_port *p, bool error)
 
 	tty_insert_flip_string(tty_port, dma->rx_buf, count);
 	p->port.icount.rx += count;
+unlock:
+	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
+
 	if (!error)
 		omap_8250_rx_dma(p, 0);
 
@@ -696,28 +707,45 @@ static void __dma_rx_complete(void *param)
 	__dma_rx_do_complete(param, false);
 }
 
+static void omap_8250_rx_dma_flush(struct uart_8250_port *p)
+{
+	struct omap8250_priv	*priv = p->port.private_data;
+	struct uart_8250_dma	*dma = p->dma;
+	unsigned long		flags;
+
+	spin_lock_irqsave(&priv->rx_dma_lock, flags);
+
+	if (!dma->rx_running) {
+		spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
+		return;
+	}
+
+	dmaengine_pause(dma->rxchan);
+
+	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
+
+	__dma_rx_do_complete(p, true);
+}
+
 static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
 {
+	struct omap8250_priv		*priv = p->port.private_data;
 	struct uart_8250_dma            *dma = p->dma;
+	int				err = 0;
 	struct dma_async_tx_descriptor  *desc;
+	unsigned long			flags;
 
 	switch (iir & 0x3f) {
 	case UART_IIR_RLSI:
 		/* 8250_core handles errors and break interrupts */
-		if (dma->rx_running) {
-			dmaengine_pause(dma->rxchan);
-			__dma_rx_do_complete(p, true);
-		}
+		omap_8250_rx_dma_flush(p);
 		return -EIO;
 	case UART_IIR_RX_TIMEOUT:
 		/*
 		 * If RCVR FIFO trigger level was not reached, complete the
 		 * transfer and let 8250_core copy the remaining data.
 		 */
-		if (dma->rx_running) {
-			dmaengine_pause(dma->rxchan);
-			__dma_rx_do_complete(p, true);
-		}
+		omap_8250_rx_dma_flush(p);
 		return -ETIMEDOUT;
 	case UART_IIR_RDI:
 		/*
@@ -729,24 +757,25 @@ static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
 		 * the DMA won't do anything soon so we have to cancel the DMA
 		 * transfer and purge the FIFO manually.
 		 */
-		if (dma->rx_running) {
-			dmaengine_pause(dma->rxchan);
-			__dma_rx_do_complete(p, true);
-		}
+		omap_8250_rx_dma_flush(p);
 		return -ETIMEDOUT;
 
 	default:
 		break;
 	}
 
+	spin_lock_irqsave(&priv->rx_dma_lock, flags);
+
 	if (dma->rx_running)
-		return 0;
+		goto out;
 
 	desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr,
 					   dma->rx_size, DMA_DEV_TO_MEM,
 					   DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
-	if (!desc)
-		return -EBUSY;
+	if (!desc) {
+		err = -EBUSY;
+		goto out;
+	}
 
 	dma->rx_running = 1;
 	desc->callback = __dma_rx_complete;
@@ -758,7 +787,9 @@ static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
 				   dma->rx_size, DMA_FROM_DEVICE);
 
 	dma_async_issue_pending(dma->rxchan);
-	return 0;
+out:
+	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
+	return err;
 }
 
 static int omap_8250_tx_dma(struct uart_8250_port *p);
@@ -1065,6 +1096,8 @@ static int omap8250_probe(struct platform_device *pdev)
 			   priv->latency);
 	INIT_WORK(&priv->qos_work, omap8250_uart_qos_work);
 
+	spin_lock_init(&priv->rx_dma_lock);
+
 	device_init_wakeup(&pdev->dev, true);
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, -1);
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index dea1eff6a92c..8799744c9069 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1349,7 +1349,7 @@ config SERIAL_ALTERA_UART_CONSOLE
 
 config SERIAL_IFX6X60
         tristate "SPI protocol driver for Infineon 6x60 modem (EXPERIMENTAL)"
-	depends on GPIOLIB && SPI
+	depends on GPIOLIB && SPI && HAS_DMA
 	help
 	  Support for the IFX6x60 modem devices on Intel MID platforms.
 
diff --git a/drivers/tty/serial/altera_jtaguart.c b/drivers/tty/serial/altera_jtaguart.c
index 0fefdd8931a2..32df2a0cb060 100644
--- a/drivers/tty/serial/altera_jtaguart.c
+++ b/drivers/tty/serial/altera_jtaguart.c
@@ -387,7 +387,7 @@ console_initcall(altera_jtaguart_console_init);
 
 #define	ALTERA_JTAGUART_CONSOLE	NULL
 
-#endif /* CONFIG_ALTERA_JTAGUART_CONSOLE */
+#endif /* CONFIG_SERIAL_ALTERA_JTAGUART_CONSOLE */
 
 static struct uart_driver altera_jtaguart_driver = {
 	.owner		= THIS_MODULE,
diff --git a/drivers/tty/serial/altera_uart.c b/drivers/tty/serial/altera_uart.c
index b2859fe07e14..fd87a6f574e3 100644
--- a/drivers/tty/serial/altera_uart.c
+++ b/drivers/tty/serial/altera_uart.c
@@ -493,7 +493,7 @@ console_initcall(altera_uart_console_init);
 
 #define	ALTERA_UART_CONSOLE	NULL
 
-#endif /* CONFIG_ALTERA_UART_CONSOLE */
+#endif /* CONFIG_SERIAL_ALTERA_UART_CONSOLE */
 
 /*
  *	Define the altera_uart UART driver structure.
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 6f5a0720a8c8..f5bd8426fd75 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -58,7 +58,6 @@
 #include <linux/pinctrl/consumer.h>
 #include <linux/sizes.h>
 #include <linux/io.h>
-#include <linux/workqueue.h>
 
 #define UART_NR			14
 
@@ -157,9 +156,7 @@ struct uart_amba_port {
 	unsigned int		lcrh_tx;	/* vendor-specific */
 	unsigned int		lcrh_rx;	/* vendor-specific */
 	unsigned int		old_cr;		/* state during shutdown */
-	struct delayed_work	tx_softirq_work;
 	bool			autorts;
-	unsigned int		tx_irq_seen;	/* 0=none, 1=1, 2=2 or more */
 	char			type[12];
 #ifdef CONFIG_DMA_ENGINE
 	/* DMA stuff */
@@ -1172,15 +1169,14 @@ static void pl011_stop_tx(struct uart_port *port)
 	pl011_dma_tx_stop(uap);
 }
 
-static bool pl011_tx_chars(struct uart_amba_port *uap);
+static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq);
 
 /* Start TX with programmed I/O only (no DMA) */
 static void pl011_start_tx_pio(struct uart_amba_port *uap)
 {
 	uap->im |= UART011_TXIM;
 	writew(uap->im, uap->port.membase + UART011_IMSC);
-	if (!uap->tx_irq_seen)
-		pl011_tx_chars(uap);
+	pl011_tx_chars(uap, false);
 }
 
 static void pl011_start_tx(struct uart_port *port)
@@ -1247,87 +1243,54 @@ __acquires(&uap->port.lock)
 	spin_lock(&uap->port.lock);
 }
 
-/*
- * Transmit a character
- * There must be at least one free entry in the TX FIFO to accept the char.
- *
- * Returns true if the FIFO might have space in it afterwards;
- * returns false if the FIFO definitely became full.
- */
-static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c)
+static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,
+			  bool from_irq)
 {
+	if (unlikely(!from_irq) &&
+	    readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
+		return false; /* unable to transmit character */
+
 	writew(c, uap->port.membase + UART01x_DR);
 	uap->port.icount.tx++;
 
-	if (likely(uap->tx_irq_seen > 1))
-		return true;
-
-	return !(readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF);
+	return true;
 }
 
-static bool pl011_tx_chars(struct uart_amba_port *uap)
+static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
 {
 	struct circ_buf *xmit = &uap->port.state->xmit;
-	int count;
-
-	if (unlikely(uap->tx_irq_seen < 2))
-		/*
-		 * Initial FIFO fill level unknown: we must check TXFF
-		 * after each write, so just try to fill up the FIFO.
-		 */
-		count = uap->fifosize;
-	else /* tx_irq_seen >= 2 */
-		/*
-		 * FIFO initially at least half-empty, so we can simply
-		 * write half the FIFO without polling TXFF.
-
-		 * Note: the *first* TX IRQ can still race with
-		 * pl011_start_tx_pio(), which can result in the FIFO
-		 * being fuller than expected in that case.
-		 */
-		count = uap->fifosize >> 1;
-
-	/*
-	 * If the FIFO is full we're guaranteed a TX IRQ at some later point,
-	 * and can't transmit immediately in any case:
-	 */
-	if (unlikely(uap->tx_irq_seen < 2 &&
-		     readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF))
-		return false;
+	int count = uap->fifosize >> 1;
 
 	if (uap->port.x_char) {
-		pl011_tx_char(uap, uap->port.x_char);
+		if (!pl011_tx_char(uap, uap->port.x_char, from_irq))
+			return;
 		uap->port.x_char = 0;
 		--count;
 	}
 	if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
 		pl011_stop_tx(&uap->port);
-		goto done;
+		return;
 	}
 
 	/* If we are using DMA mode, try to send some characters. */
 	if (pl011_dma_tx_irq(uap))
-		goto done;
+		return;
 
-	while (count-- > 0 && pl011_tx_char(uap, xmit->buf[xmit->tail])) {
-		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-		if (uart_circ_empty(xmit))
+	do {
+		if (likely(from_irq) && count-- == 0)
 			break;
-	}
+
+		if (!pl011_tx_char(uap, xmit->buf[xmit->tail], from_irq))
+			break;
+
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+	} while (!uart_circ_empty(xmit));
 
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(&uap->port);
 
-	if (uart_circ_empty(xmit)) {
+	if (uart_circ_empty(xmit))
 		pl011_stop_tx(&uap->port);
-		goto done;
-	}
-
-	if (unlikely(!uap->tx_irq_seen))
-		schedule_delayed_work(&uap->tx_softirq_work, uap->port.timeout);
-
-done:
-	return false;
 }
 
 static void pl011_modem_status(struct uart_amba_port *uap)
@@ -1354,28 +1317,6 @@ static void pl011_modem_status(struct uart_amba_port *uap)
 	wake_up_interruptible(&uap->port.state->port.delta_msr_wait);
 }
 
-static void pl011_tx_softirq(struct work_struct *work)
-{
-	struct delayed_work *dwork = to_delayed_work(work);
-	struct uart_amba_port *uap =
-		container_of(dwork, struct uart_amba_port, tx_softirq_work);
-
-	spin_lock(&uap->port.lock);
-	while (pl011_tx_chars(uap)) ;
-	spin_unlock(&uap->port.lock);
-}
-
-static void pl011_tx_irq_seen(struct uart_amba_port *uap)
-{
-	if (likely(uap->tx_irq_seen > 1))
-		return;
-
-	uap->tx_irq_seen++;
-	if (uap->tx_irq_seen < 2)
-		/* first TX IRQ */
-		cancel_delayed_work(&uap->tx_softirq_work);
-}
-
 static irqreturn_t pl011_int(int irq, void *dev_id)
 {
 	struct uart_amba_port *uap = dev_id;
@@ -1414,10 +1355,8 @@ static irqreturn_t pl011_int(int irq, void *dev_id)
 			if (status & (UART011_DSRMIS|UART011_DCDMIS|
 				      UART011_CTSMIS|UART011_RIMIS))
 				pl011_modem_status(uap);
-			if (status & UART011_TXIS) {
-				pl011_tx_irq_seen(uap);
-				pl011_tx_chars(uap);
-			}
+			if (status & UART011_TXIS)
+				pl011_tx_chars(uap, true);
 
 			if (pass_counter-- == 0)
 				break;
@@ -1639,9 +1578,6 @@ static int pl011_startup(struct uart_port *port)
 
 	writew(uap->vendor->ifls, uap->port.membase + UART011_IFLS);
 
-	/* Assume that TX IRQ doesn't work until we see one: */
-	uap->tx_irq_seen = 0;
-
 	spin_lock_irq(&uap->port.lock);
 
 	/* restore RTS and DTR */
@@ -1697,8 +1633,6 @@ static void pl011_shutdown(struct uart_port *port)
 	    container_of(port, struct uart_amba_port, port);
 	unsigned int cr;
 
-	cancel_delayed_work_sync(&uap->tx_softirq_work);
-
 	/*
 	 * disable all interrupts
 	 */
@@ -2245,7 +2179,6 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id)
 	uap->port.ops = &amba_pl011_pops;
 	uap->port.flags = UPF_BOOT_AUTOCONF;
 	uap->port.line = i;
-	INIT_DELAYED_WORK(&uap->tx_softirq_work, pl011_tx_softirq);
 
 	/* Ensure interrupts from this UART are masked and cleared */
 	writew(0, uap->port.membase + UART011_IMSC);
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 27dade29646b..b1fcddd6652a 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -165,6 +165,7 @@ struct atmel_uart_port {
 	struct tasklet_struct	tasklet;
 	unsigned int		irq_status;
 	unsigned int		irq_status_prev;
+	unsigned int		status_change;
 
 	struct circ_buf		rx_ring;
 
@@ -1177,6 +1178,9 @@ atmel_handle_status(struct uart_port *port, unsigned int pending,
 	if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
 				| ATMEL_US_CTSIC)) {
 		atmel_port->irq_status = status;
+		atmel_port->status_change = atmel_port->irq_status ^
+					    atmel_port->irq_status_prev;
+		atmel_port->irq_status_prev = status;
 		tasklet_schedule(&atmel_port->tasklet);
 	}
 }
@@ -1523,17 +1527,14 @@ static void atmel_tasklet_func(unsigned long data)
 {
 	struct uart_port *port = (struct uart_port *)data;
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
-	unsigned int status;
-	unsigned int status_change;
+	unsigned int status = atmel_port->irq_status;
+	unsigned int status_change = atmel_port->status_change;
 
 	/* The interrupt handler does not take the lock */
 	spin_lock(&port->lock);
 
 	atmel_port->schedule_tx(port);
 
-	status = atmel_port->irq_status;
-	status_change = status ^ atmel_port->irq_status_prev;
-
 	if (status_change & (ATMEL_US_RI | ATMEL_US_DSR
 				| ATMEL_US_DCD | ATMEL_US_CTS)) {
 		/* TODO: All reads to CSR will clear these interrupts! */
@@ -1548,7 +1549,7 @@ static void atmel_tasklet_func(unsigned long data)
 
 		wake_up_interruptible(&port->state->port.delta_msr_wait);
 
-		atmel_port->irq_status_prev = status;
+		atmel_port->status_change = 0;
 	}
 
 	atmel_port->schedule_rx(port);
diff --git a/drivers/tty/serial/bfin_uart.c b/drivers/tty/serial/bfin_uart.c
index 155781ece050..ae3cf94b146b 100644
--- a/drivers/tty/serial/bfin_uart.c
+++ b/drivers/tty/serial/bfin_uart.c
@@ -74,8 +74,8 @@ static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
 
 static void bfin_serial_reset_irda(struct uart_port *port);
 
-#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+#if defined(SERIAL_BFIN_CTSRTS) || \
+	defined(SERIAL_BFIN_HARD_CTSRTS)
 static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
 {
 	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
@@ -110,7 +110,7 @@ static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
 	struct bfin_serial_port *uart = dev_id;
 	struct uart_port *uport = &uart->port;
 	unsigned int status = bfin_serial_get_mctrl(uport);
-#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+#ifdef SERIAL_BFIN_HARD_CTSRTS
 
 	UART_CLEAR_SCTS(uart);
 	if (uport->hw_stopped) {
@@ -700,7 +700,7 @@ static int bfin_serial_startup(struct uart_port *port)
 # endif
 #endif
 
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+#ifdef SERIAL_BFIN_CTSRTS
 	if (uart->cts_pin >= 0) {
 		if (request_irq(gpio_to_irq(uart->cts_pin),
 			bfin_serial_mctrl_cts_int,
@@ -718,7 +718,7 @@ static int bfin_serial_startup(struct uart_port *port)
 			gpio_direction_output(uart->rts_pin, 0);
 	}
 #endif
-#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+#ifdef SERIAL_BFIN_HARD_CTSRTS
 	if (uart->cts_pin >= 0) {
 		if (request_irq(uart->status_irq, bfin_serial_mctrl_cts_int,
 			0, "BFIN_UART_MODEM_STATUS", uart)) {
@@ -766,13 +766,13 @@ static void bfin_serial_shutdown(struct uart_port *port)
 	free_irq(uart->tx_irq, uart);
 #endif
 
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+#ifdef SERIAL_BFIN_CTSRTS
 	if (uart->cts_pin >= 0)
 		free_irq(gpio_to_irq(uart->cts_pin), uart);
 	if (uart->rts_pin >= 0)
 		gpio_free(uart->rts_pin);
 #endif
-#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+#ifdef SERIAL_BFIN_HARD_CTSRTS
 	if (uart->cts_pin >= 0)
 		free_irq(uart->status_irq, uart);
 #endif
@@ -788,7 +788,7 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
 	unsigned int ier, lcr = 0;
 	unsigned long timeout;
 
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+#ifdef SERIAL_BFIN_CTSRTS
 	if (old == NULL && uart->cts_pin != -1)
 		termios->c_cflag |= CRTSCTS;
 	else if (uart->cts_pin == -1)
@@ -1110,8 +1110,8 @@ bfin_serial_console_setup(struct console *co, char *options)
 	int baud = 57600;
 	int bits = 8;
 	int parity = 'n';
-# if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+# if defined(SERIAL_BFIN_CTSRTS) || \
+	defined(SERIAL_BFIN_HARD_CTSRTS)
 	int flow = 'r';
 # else
 	int flow = 'n';
@@ -1322,8 +1322,8 @@ static int bfin_serial_probe(struct platform_device *pdev)
 		init_timer(&(uart->rx_dma_timer));
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+#if defined(SERIAL_BFIN_CTSRTS) || \
+	defined(SERIAL_BFIN_HARD_CTSRTS)
 		res = platform_get_resource(pdev, IORESOURCE_IO, 0);
 		if (res == NULL)
 			uart->cts_pin = -1;
diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c
index 0c1825b0b41d..7dced3a3f96b 100644
--- a/drivers/tty/serial/crisv10.c
+++ b/drivers/tty/serial/crisv10.c
@@ -56,10 +56,6 @@ static char *serial_version = "$Revision: 1.25 $";
 #error "RX_TIMEOUT_TICKS == 0 not allowed, use 1"
 #endif
 
-#if defined(CONFIG_ETRAX_RS485_ON_PA) && defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-#error "Disable either CONFIG_ETRAX_RS485_ON_PA or CONFIG_ETRAX_RS485_ON_PORT_G"
-#endif
-
 /*
  * All of the compatibilty code so we can compile serial.c against
  * older kernels is hidden in serial_compat.h
@@ -455,30 +451,6 @@ static struct e100_serial rs_table[] = {
 static struct fast_timer fast_timers[NR_PORTS];
 #endif
 
-#ifdef CONFIG_ETRAX_SERIAL_PROC_ENTRY
-#define PROCSTAT(x) x
-struct ser_statistics_type {
-	int overrun_cnt;
-	int early_errors_cnt;
-	int ser_ints_ok_cnt;
-	int errors_cnt;
-	unsigned long int processing_flip;
-	unsigned long processing_flip_still_room;
-	unsigned long int timeout_flush_cnt;
-	int rx_dma_ints;
-	int tx_dma_ints;
-	int rx_tot;
-	int tx_tot;
-};
-
-static struct ser_statistics_type ser_stat[NR_PORTS];
-
-#else
-
-#define PROCSTAT(x)
-
-#endif /* CONFIG_ETRAX_SERIAL_PROC_ENTRY */
-
 /* RS-485 */
 #if defined(CONFIG_ETRAX_RS485)
 #ifdef CONFIG_ETRAX_FAST_TIMER
@@ -487,9 +459,6 @@ static struct fast_timer fast_timers_rs485[NR_PORTS];
 #if defined(CONFIG_ETRAX_RS485_ON_PA)
 static int rs485_pa_bit = CONFIG_ETRAX_RS485_ON_PA_BIT;
 #endif
-#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-static int rs485_port_g_bit = CONFIG_ETRAX_RS485_ON_PORT_G_BIT;
-#endif
 #endif
 
 /* Info and macros needed for each ports extra control/status signals. */
@@ -739,10 +708,10 @@ static unsigned char dummy_ser[NR_PORTS] = {0xFF, 0xFF, 0xFF,0xFF};
     defined(CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED) || \
     defined(CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED) || \
     defined(CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED)
-#define CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED
+#define ETRAX_SERX_DTR_RI_DSR_CD_MIXED
 #endif
 
-#ifdef CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED
+#ifdef ETRAX_SERX_DTR_RI_DSR_CD_MIXED
 /* The pins can be mixed on PA and PB */
 #define CONTROL_PINS_PORT_NOT_USED(line) \
   &dummy_ser[line], &dummy_ser[line], \
@@ -835,7 +804,7 @@ static const struct control_pins e100_modem_pins[NR_PORTS] =
 #endif
 	}
 };
-#else  /* CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
+#else  /* ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
 
 /* All pins are on either PA or PB for each serial port */
 #define CONTROL_PINS_PORT_NOT_USED(line) \
@@ -917,7 +886,7 @@ static const struct control_pins e100_modem_pins[NR_PORTS] =
 #endif
 	}
 };
-#endif /* !CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
+#endif /* !ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
 
 #define E100_RTS_MASK 0x20
 #define E100_CTS_MASK 0x40
@@ -1367,16 +1336,6 @@ e100_enable_rs485(struct tty_struct *tty, struct serial_rs485 *r)
 #if defined(CONFIG_ETRAX_RS485_ON_PA)
 	*R_PORT_PA_DATA = port_pa_data_shadow |= (1 << rs485_pa_bit);
 #endif
-#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-	REG_SHADOW_SET(R_PORT_G_DATA,  port_g_data_shadow,
-		       rs485_port_g_bit, 1);
-#endif
-#if defined(CONFIG_ETRAX_RS485_LTC1387)
-	REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-		       CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 1);
-	REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-		       CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 1);
-#endif
 
 	info->rs485 = *r;
 
@@ -1841,7 +1800,6 @@ static void receive_chars_dma(struct e100_serial *info)
 		 */
 		unsigned char data = info->ioport[REG_DATA];
 
-		PROCSTAT(ser_stat[info->line].errors_cnt++);
 		DEBUG_LOG(info->line, "#dERR: s d 0x%04X\n",
 			  ((rstat & SER_ERROR_MASK) << 8) | data);
 
@@ -1943,7 +1901,6 @@ tr_interrupt(int irq, void *dev_id)
 			/* Read jiffies_usec first,
 			 * we want this time to be as late as possible
 			 */
- 			PROCSTAT(ser_stat[info->line].tx_dma_ints++);
 			info->last_tx_active_usec = GET_JIFFIES_USEC();
 			info->last_tx_active = jiffies;
 			transmit_chars_dma(info);
@@ -2022,7 +1979,6 @@ static int force_eop_if_needed(struct e100_serial *info)
 	 */
 	if (!info->forced_eop) {
 		info->forced_eop = 1;
-		PROCSTAT(ser_stat[info->line].timeout_flush_cnt++);
 		TIMERD(DEBUG_LOG(info->line, "timeout EOP %i\n", info->line));
 		FORCE_EOP(info);
 	}
@@ -2374,7 +2330,6 @@ static void handle_ser_rx_interrupt(struct e100_serial *info)
 			DEBUG_LOG(info->line, "#iERR s d %04X\n",
 			          ((rstat & SER_ERROR_MASK) << 8) | data);
 		}
-		PROCSTAT(ser_stat[info->line].early_errors_cnt++);
 	} else { /* It was a valid byte, now let the DMA do the rest */
 		unsigned long curr_time_u = GET_JIFFIES_USEC();
 		unsigned long curr_time = jiffies;
@@ -2407,7 +2362,6 @@ static void handle_ser_rx_interrupt(struct e100_serial *info)
 		DINTR2(DEBUG_LOG(info->line, "ser_rx OK %d\n", info->line));
 		info->break_detected_cnt = 0;
 
-		PROCSTAT(ser_stat[info->line].ser_ints_ok_cnt++);
 	}
 	/* Restarting the DMA never hurts */
 	*info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, restart);
@@ -2867,19 +2821,6 @@ change_speed(struct e100_serial *info)
 			*R_SERIAL_PRESCALE = divisor;
 			info->baud = SERIAL_PRESCALE_BASE/divisor;
 		}
-#ifdef CONFIG_ETRAX_EXTERN_PB6CLK_ENABLED
-		else if ((info->baud_base==CONFIG_ETRAX_EXTERN_PB6CLK_FREQ/8 &&
-			  info->custom_divisor == 1) ||
-			 (info->baud_base==CONFIG_ETRAX_EXTERN_PB6CLK_FREQ &&
-			  info->custom_divisor == 8)) {
-				/* ext_clk selected */
-				alt_source =
-					IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, extern) |
-					IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, extern);
-				DBAUD(printk("using external baudrate: %lu\n", CONFIG_ETRAX_EXTERN_PB6CLK_FREQ/8));
-				info->baud = CONFIG_ETRAX_EXTERN_PB6CLK_FREQ/8;
-			}
-#endif
 		else
 		{
 			/* Bad baudbase, we don't support using timer0
@@ -3216,9 +3157,7 @@ rs_throttle(struct tty_struct * tty)
 {
 	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
 #ifdef SERIAL_DEBUG_THROTTLE
-	char	buf[64];
-
-	printk("throttle %s: %lu....\n", tty_name(tty, buf),
+	printk("throttle %s: %lu....\n", tty_name(tty),
 	       (unsigned long)tty->ldisc.chars_in_buffer(tty));
 #endif
 	DFLOW(DEBUG_LOG(info->line,"rs_throttle %lu\n", tty->ldisc.chars_in_buffer(tty)));
@@ -3238,9 +3177,7 @@ rs_unthrottle(struct tty_struct * tty)
 {
 	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
 #ifdef SERIAL_DEBUG_THROTTLE
-	char	buf[64];
-
-	printk("unthrottle %s: %lu....\n", tty_name(tty, buf),
+	printk("unthrottle %s: %lu....\n", tty_name(tty),
 	       (unsigned long)tty->ldisc.chars_in_buffer(tty));
 #endif
 	DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc %d\n", tty->ldisc.chars_in_buffer(tty)));
@@ -3725,16 +3662,6 @@ rs_close(struct tty_struct *tty, struct file * filp)
 #if defined(CONFIG_ETRAX_RS485_ON_PA)
 		*R_PORT_PA_DATA = port_pa_data_shadow &= ~(1 << rs485_pa_bit);
 #endif
-#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-		REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-			       rs485_port_g_bit, 0);
-#endif
-#if defined(CONFIG_ETRAX_RS485_LTC1387)
-		REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-			       CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 0);
-		REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-			       CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 0);
-#endif
 	}
 #endif
 
@@ -4263,15 +4190,6 @@ static int __init rs_init(void)
 		return -EBUSY;
 	}
 #endif
-#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-	if (cris_io_interface_allocate_pins(if_serial_0, 'g', rs485_pa_bit,
-			rs485_port_g_bit)) {
-		printk(KERN_ERR "ETRAX100LX serial: Could not allocate "
-			"RS485 pin\n");
-		put_tty_driver(driver);
-		return -EBUSY;
-	}
-#endif
 #endif
 
 	/* Initialize the tty_driver structure */
diff --git a/drivers/tty/serial/ifx6x60.c b/drivers/tty/serial/ifx6x60.c
index 590390970996..536a33b99be9 100644
--- a/drivers/tty/serial/ifx6x60.c
+++ b/drivers/tty/serial/ifx6x60.c
@@ -1175,7 +1175,7 @@ static int ifx_spi_spi_probe(struct spi_device *spi)
 	ret = request_irq(gpio_to_irq(ifx_dev->gpio.reset_out),
 			  ifx_spi_reset_interrupt,
 			  IRQF_TRIGGER_RISING|IRQF_TRIGGER_FALLING, DRVNAME,
-		(void *)ifx_dev);
+			  ifx_dev);
 	if (ret) {
 		dev_err(&spi->dev, "Unable to get irq %x\n",
 			gpio_to_irq(ifx_dev->gpio.reset_out));
@@ -1185,9 +1185,8 @@ static int ifx_spi_spi_probe(struct spi_device *spi)
 	ret = ifx_spi_reset(ifx_dev);
 
 	ret = request_irq(gpio_to_irq(ifx_dev->gpio.srdy),
-			  ifx_spi_srdy_interrupt,
-			  IRQF_TRIGGER_RISING, DRVNAME,
-			  (void *)ifx_dev);
+			  ifx_spi_srdy_interrupt, IRQF_TRIGGER_RISING, DRVNAME,
+			  ifx_dev);
 	if (ret) {
 		dev_err(&spi->dev, "Unable to get irq %x",
 			gpio_to_irq(ifx_dev->gpio.srdy));
@@ -1212,7 +1211,7 @@ static int ifx_spi_spi_probe(struct spi_device *spi)
 	return 0;
 
 error_ret7:
-	free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), (void *)ifx_dev);
+	free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), ifx_dev);
 error_ret6:
 	gpio_free(ifx_dev->gpio.srdy);
 error_ret5:
@@ -1243,8 +1242,8 @@ static int ifx_spi_spi_remove(struct spi_device *spi)
 	/* stop activity */
 	tasklet_kill(&ifx_dev->io_work_tasklet);
 	/* free irq */
-	free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), (void *)ifx_dev);
-	free_irq(gpio_to_irq(ifx_dev->gpio.srdy), (void *)ifx_dev);
+	free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), ifx_dev);
+	free_irq(gpio_to_irq(ifx_dev->gpio.srdy), ifx_dev);
 
 	gpio_free(ifx_dev->gpio.srdy);
 	gpio_free(ifx_dev->gpio.mrdy);
@@ -1381,7 +1380,7 @@ static void __exit ifx_spi_exit(void)
 	/* unregister */
 	tty_unregister_driver(tty_drv);
 	put_tty_driver(tty_drv);
-	spi_unregister_driver((void *)&ifx_spi_driver);
+	spi_unregister_driver(&ifx_spi_driver);
 	unregister_reboot_notifier(&ifx_modem_reboot_notifier_block);
 }
 
@@ -1420,7 +1419,7 @@ static int __init ifx_spi_init(void)
 		goto err_free_tty;
 	}
 
-	result = spi_register_driver((void *)&ifx_spi_driver);
+	result = spi_register_driver(&ifx_spi_driver);
 	if (result) {
 		pr_err("%s: spi_register_driver failed(%d)",
 			DRVNAME, result);
@@ -1436,7 +1435,7 @@ static int __init ifx_spi_init(void)
 
 	return 0;
 err_unreg_spi:
-	spi_unregister_driver((void *)&ifx_spi_driver);
+	spi_unregister_driver(&ifx_spi_driver);
 err_unreg_tty:
 	tty_unregister_driver(tty_drv);
 err_free_tty:
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index c8cfa0637128..8aff0b4d8ddf 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -853,7 +853,7 @@ static void imx_break_ctl(struct uart_port *port, int break_state)
 #define TXTL 2 /* reset default */
 #define RXTL 1 /* reset default */
 
-static int imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
+static void imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
 {
 	unsigned int val;
 
@@ -861,7 +861,6 @@ static int imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
 	val = readl(sport->port.membase + UFCR) & (UFCR_RFDIV | UFCR_DCEDTE);
 	val |= TXTL << UFCR_TXTL_SHF | RXTL;
 	writel(val, sport->port.membase + UFCR);
-	return 0;
 }
 
 #define RX_BUF_SIZE	(PAGE_SIZE)
@@ -1114,6 +1113,12 @@ static int imx_startup(struct uart_port *port)
 
 	writel(temp & ~UCR4_DREN, sport->port.membase + UCR4);
 
+	/* Can we enable the DMA support? */
+	if (is_imx6q_uart(sport) && !uart_console(port) &&
+	    !sport->dma_is_inited)
+		imx_uart_dma_init(sport);
+
+	spin_lock_irqsave(&sport->port.lock, flags);
 	/* Reset fifo's and state machines */
 	i = 100;
 
@@ -1124,13 +1129,6 @@ static int imx_startup(struct uart_port *port)
 	while (!(readl(sport->port.membase + UCR2) & UCR2_SRST) && (--i > 0))
 		udelay(1);
 
-	/* Can we enable the DMA support? */
-	if (is_imx6q_uart(sport) && !uart_console(port) &&
-	    !sport->dma_is_inited)
-		imx_uart_dma_init(sport);
-
-	spin_lock_irqsave(&sport->port.lock, flags);
-
 	/*
 	 * Finally, clear and enable interrupts
 	 */
diff --git a/drivers/tty/serial/kgdb_nmi.c b/drivers/tty/serial/kgdb_nmi.c
index 129dc5be6028..117df151627d 100644
--- a/drivers/tty/serial/kgdb_nmi.c
+++ b/drivers/tty/serial/kgdb_nmi.c
@@ -173,18 +173,18 @@ static int kgdb_nmi_poll_one_knock(void)
 bool kgdb_nmi_poll_knock(void)
 {
 	if (kgdb_nmi_knock < 0)
-		return 1;
+		return true;
 
 	while (1) {
 		int ret;
 
 		ret = kgdb_nmi_poll_one_knock();
 		if (ret == NO_POLL_CHAR)
-			return 0;
+			return false;
 		else if (ret == 1)
 			break;
 	}
-	return 1;
+	return true;
 }
 
 /*
diff --git a/drivers/tty/serial/mcf.c b/drivers/tty/serial/mcf.c
index a9b0ab38a68c..02eb32217685 100644
--- a/drivers/tty/serial/mcf.c
+++ b/drivers/tty/serial/mcf.c
@@ -597,7 +597,7 @@ console_initcall(mcf_console_init);
 #define	MCF_CONSOLE	NULL
 
 /****************************************************************************/
-#endif /* CONFIG_MCF_CONSOLE */
+#endif /* CONFIG_SERIAL_MCF_CONSOLE */
 /****************************************************************************/
 
 /*
diff --git a/drivers/tty/serial/meson_uart.c b/drivers/tty/serial/meson_uart.c
index 67c036702629..0fc83c962d10 100644
--- a/drivers/tty/serial/meson_uart.c
+++ b/drivers/tty/serial/meson_uart.c
@@ -370,7 +370,7 @@ static int meson_uart_verify_port(struct uart_port *port,
 static void meson_uart_release_port(struct uart_port *port)
 {
 	if (port->flags & UPF_IOREMAP) {
-		iounmap(port->membase);
+		devm_iounmap(port->dev, port->membase);
 		port->membase = NULL;
 	}
 }
diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c
index 1589f17c1fca..6fc07eb9d74e 100644
--- a/drivers/tty/serial/mpc52xx_uart.c
+++ b/drivers/tty/serial/mpc52xx_uart.c
@@ -405,7 +405,7 @@ static struct psc_ops mpc5200b_psc_ops = {
 	.get_mr1 = mpc52xx_psc_get_mr1,
 };
 
-#endif /* CONFIG_MPC52xx */
+#endif /* CONFIG_PPC_MPC52xx */
 
 #ifdef CONFIG_PPC_MPC512x
 #define FIFO_512x(port) ((struct mpc512x_psc_fifo __iomem *)(PSC(port)+1))
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 0b7bb12dfc68..eec067d8eedb 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -894,12 +894,10 @@ static int uart_set_info(struct tty_struct *tty, struct tty_port *port,
 			 * need to rate-limit; it's CAP_SYS_ADMIN only.
 			 */
 			if (uport->flags & UPF_SPD_MASK) {
-				char buf[64];
-
 				dev_notice(uport->dev,
 				       "%s sets custom speed on %s. This is deprecated.\n",
 				      current->comm,
-				      tty_name(port->tty, buf));
+				      tty_name(port->tty));
 			}
 			uart_change_speed(tty, state, NULL);
 		}
diff --git a/drivers/tty/serial/sh-sci.h b/drivers/tty/serial/sh-sci.h
index d5db81a0a430..350717404507 100644
--- a/drivers/tty/serial/sh-sci.h
+++ b/drivers/tty/serial/sh-sci.h
@@ -15,7 +15,6 @@
     defined(CONFIG_CPU_SUBTYPE_SH7720) || \
     defined(CONFIG_CPU_SUBTYPE_SH7721) || \
     defined(CONFIG_ARCH_SH73A0) || \
-    defined(CONFIG_ARCH_SH7372) || \
     defined(CONFIG_ARCH_R8A7740)
 
 # define SCxSR_RDxF_CLEAR(port)	 (serial_port_in(port, SCxSR) & 0xfffc)
diff --git a/drivers/tty/serial/sirfsoc_uart.c b/drivers/tty/serial/sirfsoc_uart.c
index 9de3eabe5737..247faed40e37 100644
--- a/drivers/tty/serial/sirfsoc_uart.c
+++ b/drivers/tty/serial/sirfsoc_uart.c
@@ -1032,19 +1032,10 @@ static void sirfsoc_uart_pm(struct uart_port *port, unsigned int state,
 			      unsigned int oldstate)
 {
 	struct sirfsoc_uart_port *sirfport = to_sirfport(port);
-	if (!state) {
-		if (sirfport->is_bt_uart) {
-			clk_prepare_enable(sirfport->clk_noc);
-			clk_prepare_enable(sirfport->clk_general);
-		}
+	if (!state)
 		clk_prepare_enable(sirfport->clk);
-	} else {
+	else
 		clk_disable_unprepare(sirfport->clk);
-		if (sirfport->is_bt_uart) {
-			clk_disable_unprepare(sirfport->clk_general);
-			clk_disable_unprepare(sirfport->clk_noc);
-		}
-	}
 }
 
 static int sirfsoc_uart_startup(struct uart_port *port)
@@ -1393,20 +1384,6 @@ usp_no_flow_control:
 		goto err;
 	}
 	port->uartclk = clk_get_rate(sirfport->clk);
-	if (of_device_is_compatible(pdev->dev.of_node, "sirf,atlas7-bt-uart")) {
-		sirfport->clk_general = devm_clk_get(&pdev->dev, "general");
-		if (IS_ERR(sirfport->clk_general)) {
-			ret = PTR_ERR(sirfport->clk_general);
-			goto err;
-		}
-		sirfport->clk_noc = devm_clk_get(&pdev->dev, "noc");
-		if (IS_ERR(sirfport->clk_noc)) {
-			ret = PTR_ERR(sirfport->clk_noc);
-			goto err;
-		}
-		sirfport->is_bt_uart = true;
-	} else
-		sirfport->is_bt_uart = false;
 
 	port->ops = &sirfsoc_uart_ops;
 	spin_lock_init(&port->lock);
diff --git a/drivers/tty/serial/sirfsoc_uart.h b/drivers/tty/serial/sirfsoc_uart.h
index 727eb6b88fff..11fd6814f76d 100644
--- a/drivers/tty/serial/sirfsoc_uart.h
+++ b/drivers/tty/serial/sirfsoc_uart.h
@@ -417,10 +417,6 @@ struct sirfsoc_uart_port {
 
 	struct uart_port		port;
 	struct clk			*clk;
-	/* UART6 for BT usage in A7DA platform need multi-clock source */
-	bool				is_bt_uart;
-	struct clk			*clk_general;
-	struct clk			*clk_noc;
 	/* for SiRFatlas7, there are SET/CLR for UART_INT_EN */
 	bool				is_atlas7;
 	struct sirfsoc_uart_register	*uart_reg;
diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c
index e5695467598f..57fc6ee12332 100644
--- a/drivers/tty/tty_io.c
+++ b/drivers/tty/tty_io.c
@@ -235,7 +235,6 @@ static void tty_del_file(struct file *file)
 /**
  *	tty_name	-	return tty naming
  *	@tty: tty structure
- *	@buf: buffer for output
  *
  *	Convert a tty structure into a name. The name reflects the kernel
  *	naming policy and if udev is in use may not reflect user space
@@ -243,13 +242,11 @@ static void tty_del_file(struct file *file)
  *	Locking: none
  */
 
-char *tty_name(struct tty_struct *tty, char *buf)
+const char *tty_name(const struct tty_struct *tty)
 {
 	if (!tty) /* Hmm.  NULL pointer.  That's fun. */
-		strcpy(buf, "NULL tty");
-	else
-		strcpy(buf, tty->name);
-	return buf;
+		return "NULL tty";
+	return tty->name;
 }
 
 EXPORT_SYMBOL(tty_name);
@@ -770,8 +767,7 @@ static void do_tty_hangup(struct work_struct *work)
 void tty_hangup(struct tty_struct *tty)
 {
 #ifdef TTY_DEBUG_HANGUP
-	char	buf[64];
-	printk(KERN_DEBUG "%s hangup...\n", tty_name(tty, buf));
+	printk(KERN_DEBUG "%s hangup...\n", tty_name(tty));
 #endif
 	schedule_work(&tty->hangup_work);
 }
@@ -790,9 +786,7 @@ EXPORT_SYMBOL(tty_hangup);
 void tty_vhangup(struct tty_struct *tty)
 {
 #ifdef TTY_DEBUG_HANGUP
-	char	buf[64];
-
-	printk(KERN_DEBUG "%s vhangup...\n", tty_name(tty, buf));
+	printk(KERN_DEBUG "%s vhangup...\n", tty_name(tty));
 #endif
 	__tty_hangup(tty, 0);
 }
@@ -831,9 +825,7 @@ void tty_vhangup_self(void)
 static void tty_vhangup_session(struct tty_struct *tty)
 {
 #ifdef TTY_DEBUG_HANGUP
-	char	buf[64];
-
-	printk(KERN_DEBUG "%s vhangup session...\n", tty_name(tty, buf));
+	printk(KERN_DEBUG "%s vhangup session...\n", tty_name(tty));
 #endif
 	__tty_hangup(tty, 1);
 }
@@ -1769,7 +1761,6 @@ int tty_release(struct inode *inode, struct file *filp)
 	struct tty_struct *o_tty = NULL;
 	int	do_sleep, final;
 	int	idx;
-	char	buf[64];
 	long	timeout = 0;
 	int	once = 1;
 
@@ -1793,7 +1784,7 @@ int tty_release(struct inode *inode, struct file *filp)
 
 #ifdef TTY_DEBUG_HANGUP
 	printk(KERN_DEBUG "%s: %s (tty count=%d)...\n", __func__,
-			tty_name(tty, buf), tty->count);
+			tty_name(tty), tty->count);
 #endif
 
 	if (tty->ops->close)
@@ -1844,7 +1835,7 @@ int tty_release(struct inode *inode, struct file *filp)
 		if (once) {
 			once = 0;
 			printk(KERN_WARNING "%s: %s: read/write wait queue active!\n",
-			       __func__, tty_name(tty, buf));
+			       __func__, tty_name(tty));
 		}
 		schedule_timeout_killable(timeout);
 		if (timeout < 120 * HZ)
@@ -1856,13 +1847,13 @@ int tty_release(struct inode *inode, struct file *filp)
 	if (o_tty) {
 		if (--o_tty->count < 0) {
 			printk(KERN_WARNING "%s: bad pty slave count (%d) for %s\n",
-				__func__, o_tty->count, tty_name(o_tty, buf));
+				__func__, o_tty->count, tty_name(o_tty));
 			o_tty->count = 0;
 		}
 	}
 	if (--tty->count < 0) {
 		printk(KERN_WARNING "%s: bad tty->count (%d) for %s\n",
-				__func__, tty->count, tty_name(tty, buf));
+				__func__, tty->count, tty_name(tty));
 		tty->count = 0;
 	}
 
@@ -1905,7 +1896,7 @@ int tty_release(struct inode *inode, struct file *filp)
 		return 0;
 
 #ifdef TTY_DEBUG_HANGUP
-	printk(KERN_DEBUG "%s: %s: final close\n", __func__, tty_name(tty, buf));
+	printk(KERN_DEBUG "%s: %s: final close\n", __func__, tty_name(tty));
 #endif
 	/*
 	 * Ask the line discipline code to release its structures
@@ -1916,7 +1907,8 @@ int tty_release(struct inode *inode, struct file *filp)
 	tty_flush_works(tty);
 
 #ifdef TTY_DEBUG_HANGUP
-	printk(KERN_DEBUG "%s: %s: freeing structure...\n", __func__, tty_name(tty, buf));
+	printk(KERN_DEBUG "%s: %s: freeing structure...\n", __func__,
+	       tty_name(tty));
 #endif
 	/*
 	 * The release_tty function takes care of the details of clearing
diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c
index 8e53fe469664..5232fb60b0b1 100644
--- a/drivers/tty/tty_ioctl.c
+++ b/drivers/tty/tty_ioctl.c
@@ -211,9 +211,7 @@ int tty_unthrottle_safe(struct tty_struct *tty)
 void tty_wait_until_sent(struct tty_struct *tty, long timeout)
 {
 #ifdef TTY_DEBUG_WAIT_UNTIL_SENT
-	char buf[64];
-
-	printk(KERN_DEBUG "%s wait until sent...\n", tty_name(tty, buf));
+	printk(KERN_DEBUG "%s wait until sent...\n", tty_name(tty));
 #endif
 	if (!timeout)
 		timeout = MAX_SCHEDULE_TIMEOUT;
diff --git a/drivers/tty/tty_ldisc.c b/drivers/tty/tty_ldisc.c
index 3737f55272d2..c07fb5d9bcf9 100644
--- a/drivers/tty/tty_ldisc.c
+++ b/drivers/tty/tty_ldisc.c
@@ -22,9 +22,8 @@
 #undef LDISC_DEBUG_HANGUP
 
 #ifdef LDISC_DEBUG_HANGUP
-#define tty_ldisc_debug(tty, f, args...) ({				       \
-	char __b[64];							       \
-	printk(KERN_DEBUG "%s: %s: " f, __func__, tty_name(tty, __b), ##args); \
+#define tty_ldisc_debug(tty, f, args...) ({				  \
+	printk(KERN_DEBUG "%s: %s: " f, __func__, tty_name(tty), ##args); \
 })
 #else
 #define tty_ldisc_debug(tty, f, args...)
@@ -483,7 +482,6 @@ static void tty_ldisc_close(struct tty_struct *tty, struct tty_ldisc *ld)
 
 static void tty_ldisc_restore(struct tty_struct *tty, struct tty_ldisc *old)
 {
-	char buf[64];
 	struct tty_ldisc *new_ldisc;
 	int r;
 
@@ -504,7 +502,7 @@ static void tty_ldisc_restore(struct tty_struct *tty, struct tty_ldisc *old)
 		if (r < 0)
 			panic("Couldn't open N_TTY ldisc for "
 			      "%s --- error %d.",
-			      tty_name(tty, buf), r);
+			      tty_name(tty), r);
 	}
 }
 
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 025dad9dcde4..297d4fa1cfe5 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -35,7 +35,7 @@
 #define uart_console(port) \
 	((port)->cons && (port)->cons->index == (port)->line)
 #else
-#define uart_console(port)      (0)
+#define uart_console(port)      ({ (void)port; 0; })
 #endif
 
 struct uart_port;
diff --git a/include/linux/tty.h b/include/linux/tty.h
index d76631f615c2..ad6c8913aa3e 100644
--- a/include/linux/tty.h
+++ b/include/linux/tty.h
@@ -422,7 +422,7 @@ static inline struct tty_struct *tty_kref_get(struct tty_struct *tty)
 
 extern int tty_paranoia_check(struct tty_struct *tty, struct inode *inode,
 			      const char *routine);
-extern char *tty_name(struct tty_struct *tty, char *buf);
+extern const char *tty_name(const struct tty_struct *tty);
 extern void tty_wait_until_sent(struct tty_struct *tty, long timeout);
 extern int tty_check_change(struct tty_struct *tty);
 extern void __stop_tty(struct tty_struct *tty);