Age | Commit message (Collapse) | Author |
|
commit 05909d5c679cf7c9a8a5bc663677c066a546894f upstream.
VT1802 codec seems to reset EAPD of other pins in the hardware level,
and this was another reason of the silent headphone output on some
machines. As a workaround, introduce a new flag indicating to keep
the EPAD on to the generic parser, and set it in patch_via.c.
Reported-by: Alex Riesen <raa.lkml@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 77afe0e94884ae40de29cd813a1fb7ddee583591 upstream.
Some codec drivers (VIA codecs and some Realtek fixups) set the
automute and automic hooks after calling
snd_hda_gen_parse_auto_config(). In the current code, the hook
pointers are referred only in snd_hda_gen_parse_auto_config() and
passed to snd_hda_jack_detect_enable_callback(), thus changing the
hook values won't change the actually called callbacks properly.
This patch fixes this bug by setting the static functions as the
primary callback functions for the jack detection, and let them
calling the appropriate hooks dynamically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a6f294e87974e6ec68d7113553ffd975d83bf15 upstream.
VIA driver has a special suspend handling only for VT1802 to reduce
the pop noise. During the transition to the generic parser, the
behavior of snd_hda_set_pin_ctl() was also changed to modify the
cached values, too. And this caused a regression where the pin is
still cleared even after the resume (including the resume from power
save), resulting in the silent output.
The fix is simply to replace snd_hda_set_pin_ctl() with the explicit
call of snd_hda_codec_write() again.
Reported-by: Alex Riesen <raa.lkml@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 087c2e3b4e062573dbbc8a50b9208992e3768dcf upstream.
Since the transition to the generic parser, the actual routes used
there don't match always with the assumed static paths in some
set_widgets_power_state callbacks. This results in the wrong power
setup in the end. As a temporary workaround, we need to disable the
calls together with the non-functional dynamic power control enum.
Reported-by: Alex Riesen <raa.lkml@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af1d486c18bad7820b0ca52b413458914231102c upstream.
HP wmi platform driver fails to initialize GPS and causes poweroff
failure in HP Elitebook 6930p.
Call Trace:
[<ffffffffa088d25a>] hp_wmi_bios_setup+0x25a/0x3a0 [hp_wmi]
[<ffffffff8135978c>] platform_drv_probe+0x3c/0x70
[<ffffffff81356d6a>] ? driver_sysfs_add+0x7a/0xb0
[<ffffffff81357407>] driver_probe_device+0x87/0x3a0
[<ffffffff813577f3>] __driver_attach+0x93/0xa0
[<ffffffff81357760>] ? __device_attach+0x40/0x40
[<ffffffff81355403>] bus_for_each_dev+0x63/0xa0
[<ffffffff81356e8e>] driver_attach+0x1e/0x20
[<ffffffff81356a28>] bus_add_driver+0x1f8/0x2b0
[<ffffffff81357e81>] driver_register+0x71/0x150
[<ffffffff813594e6>] platform_driver_register+0x46/0x50
[<ffffffff813595ab>] platform_driver_probe+0x1b/0xa0
[<ffffffffa088d55e>] hp_wmi_init+0x1be/0x1fb [hp_wmi]
[<ffffffffa088d3a0>] ? hp_wmi_bios_setup+0x3a0/0x3a0 [hp_wmi]
[<ffffffff8100210a>] do_one_initcall+0x10a/0x160
[<ffffffff810bdac6>] load_module+0x1b46/0x2640
[<ffffffff8128da20>] ? ddebug_proc_write+0xf0/0xf0
[<ffffffff810be662>] sys_init_module+0xa2/0xf0
[<ffffffff814d975d>] system_call_fastpath+0x1a/0x1f
Code: 48 ff ff ff 80 7b 24 00 74 d2 41 83 e5 01 45 38 ec 74 c9 48 8d bb a0 03 00 00 e8 ed fb aa e0 5b 41 5c 41 5d 44 89 f0 41 5e 5d c3 <0f> 0b 66 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66
RIP [<ffffffffa05c57af>] rfkill_set_hw_state+0x9f/0xb0 [rfkill]
RSP <ffff880071523b60>
Check code and find this error is caused by misusing variable bluetooth_rfkill
where gps_rfkill should be.
Reported-and-tested-by: Iru Cai <mytbk920423@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=58401
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7cd8407d53ef5fb0280fcbe34f42311472f90feb upstream.
Commit b378549 (ACPI / PM: Do not power manage devices in unknown
initial states) added code to force devices without _PSC, but having
_PS0 defined in the ACPI namespace, into ACPI power state D0 by
executing _PS0 for them. That turned out to break Toshiba P870-303,
however, so revert that code.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58201
Reported-and-tested-by: Jerome Cantenot <jerome.cantenot@gmail.com>
Tracked-down-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f29ab11ddbfc12db54df5a66dab22b39ad94e8e upstream.
With the introduction of ACPI scan handlers, an ACPI device object
with an ACPI scan handler attached to it must not be bound to an ACPI
driver any more. Therefore it doesn't make sense to match those
ACPI device objects against a newly registered ACPI driver in
acpi_bus_match(), so make that function return 0 if the device
object passed to it has an ACPI scan handler attached.
This also addresses a regression related to a broken ACPI table in
the BIOS, where it has defined a _ROM method under the PCI root
bridge object. This causes the video module to treat that object
as a display controller device (since only display devices are
supposed to have a _ROM method defined according to the ACPI spec).
As a result, the ACPI video driver binds to the PCI root bridge
object and overwrites the previously assigned driver_data field of
it, causing subsequent calls to acpi_get_pci_dev() to fail.
[rjw: Subject and changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091
Reported-by: Jason Cassell <bluesloth600@gmail.com>
Reported-and-bisected-by: Dmitry S. Demin <dmitryy.demin@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 780a6ec640a3fed671fc2c40e4dd30c03eca3ac3 upstream.
This patch addresses kernel bug 56661. BIOS reports an incorrect
backlight value, causing the driver to switch off the backlight
completely during startup. This patch ignores the incorrect value from
BIOS.
References: https://bugzilla.kernel.org/show_bug.cgi?id=56661
Signed-off-by: Ash Willis <ashwillis@programmer.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fedbe9bc6fd3e14b1ffbb3dac407777ac4a3650c upstream.
On HP m4 lapops, BIOS reports minimum backlight on boot and
causes backlight to dim completely. This ignores the initial backlight
values and set to max brightness.
References: https://bugs.launchpad.net/bugs/1184501
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8673b83bf2f013379453b4779047bf3c6ae387e4 upstream.
Commit 4b31e774 (Always set P-state on initialization) fixed bug
#4634 and caused the driver to always set the target P-State at
least once since the initial P-State may not be the desired one.
Commit 5a1c0228 (cpufreq: Avoid calling cpufreq driver's target()
routine if target_freq == policy->cur) caused a regression in
this behavior.
This fixes the regression by setting policy->cur based on the CPU's
target frequency rather than the CPU's current reported frequency
(which may be different). This means that the P-State will be set
initially if the CPU's target frequency is different from the
governor's target frequency.
This fixes an issue where setting the default governor to
performance wouldn't correctly enable turbo mode on all cores.
Signed-off-by: Ross Lagerwall <rosslagerwall@gmail.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a26f009a070e840fadacb91013b2391ba7ab6cc2 upstream.
The register access to enable hardware flow control depends on the
device port number and not the port minor number.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 849513a7809175420d353625b6f651d961e99d49 upstream.
The control and bulk-message timeouts are specified in milliseconds and
should not depend on HZ.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72ea18a558ed7a63a50bb121ba60d73b5b38ae30 upstream.
The read_mos_reg function is called with stack-allocated buffers, which
must not be used for control messages.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15ee89c3347fbf58a4361011eda5ac2731e45126 upstream.
Fix regression introduced by commit 0eafe4de1a ("USB: serial: mos7840:
add support for MCS7810 devices") which used stack-allocated buffers for
control messages.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fdc03438f53a00294ed9939eb3a1f6db6f3d8963 upstream.
This patch reverts commit 3e619d04159be54b3daa0b7036b0ce9e067f4b5d
(USB: EHCI: fix bug in scheduling periodic split transfers). The
commit was valid -- it fixed a real bug -- but the periodic scheduler
in ehci-hcd is in such bad shape (especially the part that handles
split transactions) that fixing one bug is very likely to cause
another to surface. That's what happened in this case; the result was
choppy and noisy playback on certain 24-bit audio devices.
The only real fix will be to rewrite this entire section of code. My
next project...
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1136110.
Thanks to Tim Richardson for extra testing and feedback, and to Joseph
Salisbury and Tyson Tan for tracking down the original source of the
problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Joseph Salisbury <joseph.salisbury@canonical.com>
CC: Tim Richardson <tim@tim-richardson.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f8e2c07d75967ee49a5da1d21ddf5f50d48cda0 upstream.
The first and second interrupt-in urbs are swapped for some Treo/Kyocera
devices, but the urb context was never updated with the new port.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9eecf22d2b375b9064a20421c6c307b760b03d46 upstream.
When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6529591e3eef65f0f528a81ac169f6e294b947a7 upstream.
The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8a1d0d54d5fdac0347b75e9afd554b3dfaa465f upstream.
Remove bogus port-number check in open and close, which prevented this
driver from being used with a minor number different from zero.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5cbfa3acdcbf19e1d29cf3479ad8200d2e644e44 upstream.
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 420021a395ce38b7ab2cceb52dee4038be7d8fa3 upstream.
Fix regression introduced by commit 214916f2e ("USB: visor: reimplement
using generic framework") which broke initialisation of Treo/Kyocera
devices that re-mapped bulk-in endpoints.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 634371911730a462626071065b64cd6e1fe213e0 upstream.
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a07088098a650267b2eda689538133a324b9523f upstream.
The outcont_endpoints array was indexed using the port minor number
(which can be greater than the array size) rather than the device port
number.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c13ff68a7ce01da7a51b44241a7aad8eaaedde7 upstream.
The bulk-message timeout is specified in milliseconds and should not
depend on HZ.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11e7064f35bb87da8f427d1aa4bbd8b7473a3993 upstream.
USB audio driver spews an error message when probing Logitech HD
webcam c270:
ALSA mixer.c:1300 usb_audio: Warning! Unlikely big volume range (=6144), cval->res is probably wrong.
ALSA mixer.c:1304 usb_audio: [5] FU [Mic Capture Volume] ch = 1, val = 1536/7680/1
Obviously the device needs a fixed volume resolution (cval->res = 384)
like other Logitech devices.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=821735
Reported-and-tested-by: Cristian Rodríguez <crrodriguez@opensuse.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8eafc0a161123d90617c9ca2eddfe87b382b1b89 upstream.
... instead of applying to all interfaces.
Reference: http://forums.gentoo.org/viewtopic-p-6886404.html
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0c6d309c6df14655f9962f666d1da96318b0b7c upstream.
Commit 927c9423dd5f2d1c0b93d5e694ab84b4a5559713 (ALSA: usb-audio: add
Edirol UM-3G support) used a wrong quirk type, which would make the
driver refuse to attach with the error message "MIDIStreaming interface
descriptor not found".
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed74df12dc3e07a37d99aab60211496e871488a0 upstream.
Since highmem PIO URB handling was introduced in:
8e8a551 usb: musb: host: Handle highmem in PIO mode
when a URB is being handled it may happen that the static use_sg flag
was set by a previous URB with buffer in highmem. This leads to error
in handling the present URB.
Fix this by making the use_sg flag URB specific.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65694c5aaddfedd9da082e4e150cafc6b3fc8a6a upstream.
f9a37be0f0 ("x86: Use PCI setup data") added support for using PCI ROM
images from setup_data. This used phys_to_virt(), which is not valid for
highmem addresses, and can cause a crash when booting a 32-bit kernel via
the EFI boot stub.
pcibios_add_device() assumes that the physical addresses stored in
setup_data are accessible via the direct kernel mapping, and that calling
phys_to_virt() is valid. This isn't guaranteed to be true on x86 where the
direct mapping range is much smaller than on x86-64.
Calling phys_to_virt() on a highmem address results in the following:
BUG: unable to handle kernel paging request at 39a3c198
IP: [<c262be0f>] pcibios_add_device+0x2f/0x90
...
Call Trace:
[<c2370c73>] pci_device_add+0xe3/0x130
[<c274640b>] pci_scan_single_device+0x8b/0xb0
[<c2370d08>] pci_scan_slot+0x48/0x100
[<c2371904>] pci_scan_child_bus+0x24/0xc0
[<c262a7b0>] pci_acpi_scan_root+0x2c0/0x490
[<c23b7203>] acpi_pci_root_add+0x312/0x42f
...
The solution is to use ioremap() instead of phys_to_virt() to map the
setup data into the kernel address space.
[bhelgaas: changelog]
Tested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3897aa5386faba77e5bbdf94902a1658d3a5b11 upstream.
Some xHCI hosts contain a "redriver" from TI that silently drops port
status connect changes if the port slips into Compliance Mode. If the
port slips into compliance mode while the host is in D0, there will not
be a port status change event. If the port slips into compliance mode
while the host is in D3, the host will not send a PME. This includes
when the system is suspended (S3) or hibernated (S4).
If this happens when the system is in S3/S4, there is nothing software
can do. Other port status change events that would normally cause the
host to wake the system from S3/S4 may also be lost. This includes
remote wakeup, disconnects and connects on other ports, and overrcurrent
events. A decision was made to _NOT_ disable system suspend/hibernate
on these systems, since users are unlikely to enable wakeup from S3/S4
for the xHCI host.
Software can deal with this issue when the system is in S0. A work
around was put in to poll the port status registers for Compliance Mode.
The xHCI driver will continue to poll the registers while the host is
runtime suspended. Unfortunately, that means we can't allow the PCI
device to go into D3cold, because power will be removed from the host,
and the config space will read as all Fs.
Disable D3cold in the xHCI PCI runtime suspend function.
This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 88696ae432ce7321540ac53d9caab3de9118b094 upstream.
If for whatever reason we fall into fail path in xhci_mem_init()
before bw table gets initialized we may access the uninitialized lists
in xhci_mem_cleanup().
Check for bw table before traversing lists in cleanup routine.
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store
information about roothubs and TTs."
Reported-by: Sergey Dyasly <dserrg@gmail.com>
Tested-by: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 331de00a64e5027365145bdf51da27b9ce15dfd5 upstream.
It is possible that we fail on xhci_mem_init, just before doing
the INIT_LIST_HEAD, and calling xhci_mem_cleanup.
Problem is that, the list_for_each_entry_safe macro, assumes
list heads are initialized (not NULL), and dereferences their 'next'
pointer, causing a kernel panic if this is not yet initialized.
Let's protect from that by moving inits to the beginning.
This patch should be backported to kernels as old as 3.2, that
contain the commit 9574323c39d1f8359a04843075d89c9f32d8b7e6 "xHCI: test
USB2 software LPM".
Signed-off-by: Sergio Aguirre <sergio.a.aguirre.rodriguez@intel.com>
Acked-by: David Cohen <david.a.cohen@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 77df9e0b799b03e1d5d9c68062709af5f637e834 upstream.
Commit 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP
Hardware) was a workaround for systems using the SN65LVPE502CP,
controller, but it introduced a bug in resume from hibernate.
The fix created a timer, comp_mode_recovery_timer, which is deleted from
a timer list when xhci_suspend() is called. However, the hibernate image,
including the timer list containing the comp_mode_recovery_timer, had
already been saved before the timer was deleted.
Upon resume from hibernate, the list containing the comp_mode_recovery_timer
is restored from the image saved to disk, and xhci_resume(), assuming that
the timer had been deleted by xhci_suspend(), makes a call to
compliance_mode_recoery_timer_init(), which creates a new instance of the
comp_mode_recovery_timer and attempts to place it into the same list in which
it is already active, thus corrupting the list during the list_add() call.
At this point, a call trace is emitted indicating the list corruption.
Soon afterward, the system locks up, the watchdog times out, and the
ensuing NMI crashes the system.
The problem did not occur when resuming from suspend. In suspend, the
image in RAM remains exactly as it was when xhci_suspend() deleted the
comp_mode_recovery_timer, so there is no problem when xhci_resume()
creates a new instance of this timer and places it in the still empty
list.
This patch avoids the problem by deleting the timer in xhci_resume()
when resuming from hibernate. Now xhci_resume() can safely make the
call to create a new instance of this timer, whether returning from
suspend or hibernate.
Thanks to Alan Stern for his help with understanding the problem.
[Sarah reworked this patch to cover the case where the xHCI restore
register operation fails, and (temp & STS_SRE) is true (and we re-init
the host, including re-init for the compliance mode), but hibernate is
false. The original patch would have caused list corruption in this
case.]
This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Tested-by: Tony Camuso <tcamuso@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f28c42c576b293b3a1daaed8ca2775ebc2fe5398 upstream.
If the glue layer is removed first (core layer later),
it deletes the phy device first, then the core device.
But at core's removal, it still uses PHY's resources, it may
cause kernel's oops. It is much like the problem
Paul Zimmerman reported at:
http://marc.info/?l=linux-usb&m=136547502011472&w=2.
Besides, it is reasonable the PHY is deleted at last as
the controller is the PHY's user.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73228a0538a70ebc4547bd09dee8971360dc1d87 upstream.
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b8a24e6281d37243c06b9497dcbfaa98c1e2ad35 upstream.
The mode used by Windows for the Huawei E1820 will use the
same ff/ff/ff class codes for both serial and network
functions.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a2f132a01c2dd4c3905fa560f92019761ed72b1 upstream.
The Option GTM681W uses a qualcomm chip and can be
served by the qcserial device driver.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 376414945d15aa636e65f7e773c1e398b7a21cb9 upstream.
This patch only changes some names to avoid confusion.
In this patch we have:
MAX_SKB_SLOTS_DEFAULT -> FATAL_SKB_SLOTS_DEFAULT
max_skb_slots -> fatal_skb_slots
#define XEN_NETBK_LEGACY_SLOTS_MAX XEN_NETIF_NR_SLOTS_MIN
The fatal_skb_slots is the threshold to determine whether a packet is
malicious.
XEN_NETBK_LEGACY_SLOTS_MAX is the maximum slots a valid packet can have at
this point. It is defined to be XEN_NETIF_NR_SLOTS_MIN because that's
guaranteed to be supported by all backends.
Suggested-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unfortunately, advertising P2P_DEVICE support was a little
premature, a number of issues came up in testing and have
been fixed for 3.10. Rather than try to backport all the
different fixes, disable P2P_DEVICE support in the drivers
using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unfortunately, advertising P2P_DEVICE support was a little
premature, a number of issues came up in testing and have
been fixed for 3.10. Rather than try to backport all the
different fixes, disable P2P_DEVICE support in the drivers
using it. For iwlmvm that implies disabling P2P completely
as it can't support P2P operation w/o P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ecd1a75d977e2e8c48139c7d3efed183f898d94 upstream.
The maximum packet including header that can be handled by netfront / netback
wire format is 65535. Reduce gso_max_size accordingly.
Drop skb and print warning when skb->len > 65535. This can 1) save the effort
to send malformed packet to netback, 2) help spotting misconfiguration of
netfront in the future.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 59ccb4ebbc35e36a3c143f2d1355deb75c2e628f upstream.
Tune xen_netbk_count_requests to not touch working array beyond limit, so that
we can make working array size constant.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac69c26e7accb04ae2cb9ab0872068983a42b3c8 upstream.
Tracking down from the caller, first_idx is always equal to vif->tx.req_cons.
Remove it to avoid confusion.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03393fd5cc2b6cdeec32b704ecba64dbb0feae3c upstream.
Some frontend drivers are sending packets > 64 KiB in length. This length
overflows the length field in the first slot making the following slots have
an invalid length.
Turn this error back into a non-fatal error by dropping the packet. To avoid
having the following slots having fatal errors, consume all slots in the
packet.
This does not reopen the security hole in XSA-39 as if the packet as an
invalid number of slots it will still hit fatal error case.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2810e5b9a7731ca5fce22bfbe12c96e16ac44b6f upstream.
This patch tries to coalesce tx requests when constructing grant copy
structures. It enables netback to deal with situation when frontend's
MAX_SKB_FRAGS is larger than backend's MAX_SKB_FRAGS.
With the help of coalescing, this patch tries to address two regressions
avoid reopening the security hole in XSA-39.
Regression 1. The reduction of the number of supported ring entries (slots)
per packet (from 18 to 17). This regression has been around for some time but
remains unnoticed until XSA-39 security fix. This is fixed by coalescing
slots.
Regression 2. The XSA-39 security fix turning "too many frags" errors from
just dropping the packet to a fatal error and disabling the VIF. This is fixed
by coalescing slots (handling 18 slots when backend's MAX_SKB_FRAGS is 17)
which rules out false positive (using 18 slots is legit) and dropping packets
using 19 to `max_skb_slots` slots.
To avoid reopening security hole in XSA-39, frontend sending packet using more
than max_skb_slots is considered malicious.
The behavior of netback for packet is thus:
1-18 slots: valid
19-max_skb_slots slots: drop and respond with an error
max_skb_slots+ slots: fatal error
max_skb_slots is configurable by admin, default value is 20.
Also change variable name from "frags" to "slots" in netbk_count_requests.
Please note that RX path still has dependency on MAX_SKB_FRAGS. This will be
fixed with separate patch.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 803d19d57a042e86e9e9b685bbc3f4a0a751040f upstream.
This reverts commit a99d76f (leds: leds-gpio: use gpio_request_one)
and commit 2d7c22f (leds: leds-gpio: set devm_gpio_request_one()
flags param correctly) which was a fix of the first one.
The conversion to devm_gpio_request in commit e3b1d44c (leds:
leds-gpio: use devm_gpio_request_one) is not reverted.
The problem is that gpio_cansleep() and gpio_get_value_cansleep()
calls can crash if the gpio is not first reserved. Incidentally this
same bug existed earlier and was fixed similarly in commit d95cbe61
(leds: Fix potential leds-gpio oops). But the OOPS is real. It happens
when GPIOs are provided by module which is not yet loaded.
So this fixes the following BUG during my ALIX boot (3.9.2-vanilla):
BUG: unable to handle kernel NULL pointer dereference at 0000004c
IP: [<c11287d6>] __gpio_cansleep+0xe/0x1a
*pde = 00000000
Oops: 0000 [#1] SMP
Modules linked in: leds_gpio(+) via_rhine mii cs5535_mfd mfd_core
geode_rng rng_core geode_aes isofs nls_utf8 nls_cp437 vfat fat
ata_generic pata_amd pata_cs5536 pata_acpi libata ehci_pci ehci_hcd
ohci_hcd usb_storage usbcore usb_common sd_mod scsi_mod squashfs loop
Pid: 881, comm: modprobe Not tainted 3.9.2 #1-Alpine
EIP: 0060:[<c11287d6>] EFLAGS: 00010282 CPU: 0
EIP is at __gpio_cansleep+0xe/0x1a
EAX: 00000000 EBX: cf364018 ECX: c132b8b9 EDX: 00000000
ESI: c13993a4 EDI: c1399370 EBP: cded9dbc ESP: cded9dbc
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
CR0: 8005003b CR2: 0000004c CR3: 0f0c4000 CR4: 00000090
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Process modprobe (pid: 881, ti=cded8000 task=cf094aa0 task.ti=cded8000)
Stack:
cded9de0 d09471cb 00000000 c1399260 cf364014 00000000 c1399260 c1399254
d0949014 cded9df4 c118cd59 c1399260 d0949014 d0949014 cded9e08 c118ba47
c1399260 d0949014 c1399294 cded9e1c c118bb75 cded9e24 d0949014 00000000
Call Trace:
[<d09471cb>] gpio_led_probe+0xba/0x203 [leds_gpio]
[<c118cd59>] platform_drv_probe+0x26/0x48
[<c118ba47>] driver_probe_device+0x75/0x15c
[<c118bb75>] __driver_attach+0x47/0x63
[<c118a727>] bus_for_each_dev+0x3c/0x66
[<c118b6f9>] driver_attach+0x14/0x16
[<c118bb2e>] ? driver_probe_device+0x15c/0x15c
[<c118b3d5>] bus_add_driver+0xbd/0x1bc
[<d08b4000>] ? 0xd08b3fff
[<d08b4000>] ? 0xd08b3fff
[<c118bffc>] driver_register+0x74/0xec
[<d08b4000>] ? 0xd08b3fff
[<c118c8e8>] platform_driver_register+0x38/0x3a
[<d08b400d>] gpio_led_driver_init+0xd/0x1000 [leds_gpio]
[<c100116c>] do_one_initcall+0x6b/0x10f
[<d08b4000>] ? 0xd08b3fff
[<c105e918>] load_module+0x1631/0x1907
[<c10975d6>] ? insert_vmalloc_vmlist+0x14/0x43
[<c1098d5b>] ? __vmalloc_node_range+0x13e/0x15f
[<c105ec50>] sys_init_module+0x62/0x77
[<c1257888>] syscall_call+0x7/0xb
EIP: [<c11287d6>] __gpio_cansleep+0xe/0x1a SS:ESP 0068:cded9dbc
CR2: 000000000000004c
---[ end trace 5308fb20d2514822 ]---
Signed-off-by: Timo Teräs <timo.teras@iki.f>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Raphael Assenat <raph@8d.com>
Cc: Trent Piepho <tpiepho@freescale.com>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21363ca873334391992f2f424856aa864345bb61 upstream.
This patch fixes a bug where FILEIO was incorrectly reporting the number
of logical blocks (+ 1) when using non struct block_device export mode.
It changes fd_get_blocks() to follow all other backend ->get_blocks() cases,
and reduces the calculated dev_size by one dev->dev_attrib.block_size
number of bytes, and also fixes initial fd_block_size assignment at
fd_configure_device() time introduced in commit 0fd97ccf4.
Reported-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reported-by: Badari Pulavarty <pbadari@us.ibm.com>
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9b31a328e344e62e7cc98ae574edcb7b674719bb upstream.
Switch back to pre commit 1c7b13fe652 list splicing logic for active I/O
shutdown with tcm_qla2xxx + ib_srpt fabrics.
The original commit was done under the incorrect assumption that it's safe to
walk se_sess->sess_cmd_list unprotected in target_wait_for_sess_cmds() after
sess->sess_tearing_down = 1 has been set by target_sess_cmd_list_set_waiting()
during session shutdown.
So instead of adding sess->sess_cmd_lock protection around sess->sess_cmd_list
during target_wait_for_sess_cmds(), switch back to sess->sess_wait_list to
allow wait_for_completion() + TFO->release_cmd() to occur without having to
walk ->sess_cmd_list after the list_splice.
Also add a check to exit if target_sess_cmd_list_set_waiting() has already
been called, and add a WARN_ON to check for any fabric bug where new se_cmds
are added to sess->sess_cmd_list after sess->sess_tearing_down = 1 has already
been set.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28420dad233520811c0e0860e7fb4975ed863fc4 upstream.
Fix bug introduced by commit 4582a4ab2a "FUSE: Adapt readdirplus to application
usage patterns".
We need to check for a positive dentry; negative dentries are not added by
readdirplus. Secondly we need to advise the use of readdirplus on the *parent*,
otherwise the whole thing is useless. Thirdly all this is only relevant if
"readdirplus_auto" mode is selected by the filesystem.
We advise the use of readdirplus only if the dentry was still valid. If we had
to redo the lookup then there was no use in doing the -plus version.
Reported-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: Feng Shuo <steve.shuo.feng@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|