| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit f2ee6dfa0e8597eea8b98d240b0033994e20d215.
Jakub Kiciński observed that this patch can cause the pl011
driver to hang if if the only process with a pl011 port open is
killed by a signal, pl011_shutdown() can get called with an
arbitrary amount of data still in the FIFO.
Calling _shutdown() with the TX FIFO non-empty is questionable
behaviour and my itself be a bug.
Since the affected patch was speculative anyway, and brings limited
benefit, the simplest course is to remove the assumption that TXIS
will always be left asserted after the port is shut down.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is pm_qos_add_request() being executed on serial_omap_probe(),
which stores "&up->pm_qos_request" from omap-serial driver to
"pm_qos_array[PM_QOS_CPU_DMA_LATENCY]->constraints". If
serial_omap_probe() fails after pm_qos_add_request() (e.g. on
uart_add_one_port() call), pm_qos_array still keeping pm_qos_request
struct from omap-serial driver, which is not valid anymore (since driver
failed). This leads further to kernel crash on pm_qos_update_target(),
executing from some completely different driver.
We were observing this while trying to run audio playback while having
one of omap-serial driver instances failed on uart_add_one_port() call:
Unable to handle kernel paging request at virtual address fffffffc
Backtrace:
(plist_add) from (pm_qos_update_target)
(pm_qos_update_target) from (pm_qos_add_request)
(pm_qos_add_request) from (snd_pcm_hw_params)
(snd_pcm_hw_params) from (snd_pcm_common_ioctl1)
(snd_pcm_common_ioctl1) from (snd_pcm_playback_ioctl1)
(snd_pcm_playback_ioctl1) from (snd_pcm_playback_ioctl)
(snd_pcm_playback_ioctl) from (do_vfs_ioctl)
(do_vfs_ioctl) from (SyS_ioctl)
(SyS_ioctl) from (ret_fast_syscall)
This patch adds pm_qos_remove_request() on fail path in
serial_omap_probe() in order to fix this issue. While at it, free the
wakeup settings on fail path as well, just like it's done in
serial_omap_remove().
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Log warnings meant to help diagnose problems setting up earlycon
are reporting false positives for 'console='. Revert to the
previous behavior which reported nothing.
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).
Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.
See: https://www.exar.com/common/content/document.ashx?id=1587 page 11
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes problems with serial console break. When function
s3c64xx_serial_startup() was started while serial console has been working,
it caused lose of characters written to TX FIFO. This effect was particularly
observable with systemd, which closes serial port every time when it's
not currently needed, hence function s3c64xx_serial_startup() is called
quite often there. To fix this problem we avoid resetting TX FIFO if port is
used as serial console.
Example of broken console log:
[ 1086.7 Expecting device dev-ttySAC1.device...
[ 1086.[ OK ] Reached target Paths.
[ 1086.756416] s[ OK ] Reached target Swap.
[ 1086.776413] systemd[1]: Reached target Swap.
[ 1086.776642] systemd[1]: Starting Root Slice.
[ 5.53403[ OK ] Created slice Root Slice.
[ 5.548433] systemd[1]: Create[ OK ] Created slice User and Session Slice.
[ 5.568414] sys[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 5.588388] s[ OK ] Listening on Delayed Shutdown Socket.
[ 5.608376] sy[ OK ] Listening on Journal Socket (/dev/log).
[ 5.628361] [ OK ] Listening on udev Kernel Socket.
[ 5.648357] s[ OK ] Listening on udev Control Socket.
[ 5.668353] s[ OK ] Listening on Journal Socket.
[ 5.688366] systemd[1]: Listeni[ OK ] Created slice System Slice.
[ 5.708393] Mounting Temporary Directory...
[ 7139.067436] Starting prepare device daemon...
[ 7139.091726] sy Starting Generate environment from /etc/profile.d...
[ 5.792867] system Starting Create Static Device Nodes in /dev...
[ 7848.718 Mounting Debug File System...
[ 7848.7384 Mounting Configuration File System...
[ 5.852 Starting Apply Kernel Variables...
[ 5.8720 Starting Setup Virtual Console...
[ 7848.798 Starting udev Coldplug all Devices...
[ 7848.817 Starting Journal Service...
[ OK ] Started Journal Service.
[ 7848.854222] s[ OK ] Reached target Slices.
Starting Remount Root and Kernel File Systems...
[ OK ] Mounted Configuration File System.
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Maxburst was not set when doing the dma slave configuration. This value
is checked by the recently introduced xdmac. It causes an error when
doing the slave configuration and so prevents from using dma.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not probe all serial drivers by of_serial.c which are using
device_type = "serial"; property. Only drivers which have valid
compatible strings listed in the driver should be probed.
When PORT_UNKNOWN is setup probe will fail anyway.
Arnd quotation about driver historical background:
"when I wrote that driver initially, the idea was that it would
get used as a stub to hook up all other serial drivers but after
that, the common code learned to create platform devices from DT"
This patch fix the problem with on the system with xilinx_uartps and
16550a where of_serial failed to register for xilinx_uartps and because
of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking
for irq with request_irq() EINVAL is returned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type =
"serial"; property in DT of_serial.c driver maps and unmaps IRQ (because
driver probe fails). Then a driver is called but irq mapping is not
created that's why driver is failing again in again on request_irq().
Based on this use platform_get_irq() instead of platform_get_resource()
which is doing irq_desc allocation and driver itself can request IRQ.
Fix both xilinx serial drivers in the tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix uart_console_write() kernel-doc build warnings.
Warning(drivers/tty/serial/serial_core.c:1778): No description found for parameter 'putchar'
Warning(drivers/tty/serial/serial_core.c:1778): Excess function parameter 'write' description in 'uart_console_write'
Fixes: 1cfe42b7fd29 ("serial: core: Fix kernel doc for uart_console_write()")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
|
|
If the device node has a "big-endian" property and 32-bit registers, tell
the serial driver to use UPIO_MEM32BE instead of UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add cases for UPIO_MEM32BE wherever there are currently cases handling
UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
* pnp:
PNP: Avoid leaving unregistered device objects in lists
PNP: Convert pnp_lock into a mutex
PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver
PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver
PNP: net/sb1000: Use module_pnp_driver to register driver
PNP: media/rc: Use module_pnp_driver to register driver
PNP: ide/ide-pnp: Use module_pnp_driver to register driver
PNP: ata/pata_isapnp: Use module_pnp_driver to register driver
PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver
PNP: Add helper macro for pnp_register_driver boilerplate
PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
|
|
Hardware is capable of inverting RTS signal when working
in RS-485 mode. Expose this functionality to user space.
Relay on a matching combination of standard flags
(SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND) to
detect when user space is requesting inverted RTS mode.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial ports of F81504/F81508/F81512 will failed when wakeup from S3(STR).
It's due to when the system wakeup from S3(STR), this PCI device's
configuration space from 0x40 to 0x40 + max_port * 0x08 should be
re-configured.
We move all initialization from pci_fintek_setup() to pci_fintek_init() and
set it to pci_serial_quirks .init section. It's will re-init this device when
system wakeup from pciserial_resume_ports().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Document the expected behavior of kernel command lines of the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
and
earlycon=uart[8250],io|mmio|mmio32,<addr>[,options]
earlycon=uart[8250],<addr>[,options]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Restore undocumented behavior of kernel command line parameters of
the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
where 'options' have not been specified; in this case, the hardware
is assumed to be initialized.
Fixes: c7cef0a84912cab3c9df8 ("console: Add extensible console matching")
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes in here as well, also to help out with merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the receiver was enabled during startup, a character could
have been in the FIFO when the UART get initially used. The
driver configures the (receive) watermark level, and flushes the
FIFO. However, the receive flag (RDRF) could still be set at that
stage (as mentioned in the register description of UARTx_RWFIFO).
This leads to an interrupt which won't be handled properly in
interrupt mode: The receive interrupt function lpuart_rxint checks
the FIFO count, which is 0 at that point (due to the flush
during initialization). The problem does not manifest when using
DMA to receive characters.
Fix this situation by explicitly read the status register, which
leads to clearing of the RDRF flag. Due to the flush just after
the status flag read, a explicit data read is not to required.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Specify transmit FIFO size which might be different depending on
LPUART instance. This makes sure uart_wait_until_sent in serial
core getting called, which in turn waits and checks if the FIFO
is really empty on shutdown by using the tx_empty callback.
Without the call of this callback, the last several characters
might not yet be transmitted when closing the serial port. This
can be reproduced by simply using echo and redirect the output to
a ttyLP device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exynos serial ports operate either in a DMA-based or interrupt-based
modes. In DMA-based mode, the UART generates a transfer data request
and a Transmission (Tx) interrupt in interrupt-based mode.
The Tx IRQ is only unmasked in interrupt-based mode and it was done
in s3c24xx_serial_start_tx(). Commit ba019a3e2ad5 ("serial: samsung:
remove redundant interrupt enabling") removed the IRQ enable on that
function since it is enabled when the mode is set in enable_tx_pio().
The problem is that enable_tx_pio() is only called if the port mode
has not been set before but the mode was not cleared on .shutdown().
So if the UART was shutdown and then started up again, the mode set
will remain and the Tx IRQ won't be unmasked.
This caused a hang on at least Exynos5250, Exynos5420 and Exynos5800
when the system is rebooted or powered off.
Fixes: ba019a3e2ad5 ("serial: samsung: remove redundant interrupt enabling")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The clock rate is requested from a property called
"clock-frequency" in both dw8250_probe_of and
dw8250_probe_acpi. Moving the requests to dw8250_probe.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Having ACPI handle does not mean the same as having ACPI
identifier. The check is in any case useless, but having it
prevents this driver from being used for example with
multifunctional PCI devices, such as the newer Intel LPSS
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Tangier contains 4 HSUART ports as found on Intel Edison board which are
8250 compatible. The patch adds necessary bits to the driver.
Note that the HSU port0 is currently unavailable and thus not supported.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for intel_mid_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) nominator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
24 25 12 48000000 64000000 4000000(1)
49 50 14 49000000 56000000 3500000(1)
4 5 16 40000000 40000000 2500000(1)
16 25 16 32000000 32000000 500000(4),1000000(2),2000000(1)
24 25 16 48000000 48000000 1500000(2),3000000(1)
2304 3125 16 36864000 36864000 576000(4),1152000(2)
8192 15625 16 26214400 26214400 50(32768),200(8192)
9216 15625 16 29491200 29491200 1800(1024),57600(32),115200(16),
230400(8),460800(4),921600(2),1843200(1)
12288 15625 16 39321600 39321600 75(32768),150(16384),300(8192),
600(4096),1200(2048),2400(1024),4800(512),
9600(256),19200(128),38400(64)
45056 78125 16 28835840 28835840 110(16384)
274432 390625 16 35127296 35127296 134(16384)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for byt_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) numerator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
4 5 16 80000000 80000000 2500000(2)
14 25 16 56000000 56000000 3500000(1)
16 25 16 64000000 64000000 500000(8),1000000(4),2000000(2),
4000000(1)
24 25 16 96000000 96000000 1500000(4),3000000(2)
2180 3103 16 70254592 70254592 134(32768)
2304 3125 16 73728000 73728000 576000(8),1152000(4)
8192 15625 16 52428800 52428800 50(65536),200(16384)
9216 15625 16 58982400 58982400 1800(2048),57600(64),115200(32),
230400(16),460800(8),921600(4),1843200(2)
12288 15625 16 78643200 78643200 75(65536),150(32768),300(16384),
600(8192),1200(4096),2400(2048),
4800(1024),9600(512),19200(256),38400(128)
9893 17154 16 57671680 57671680 110(32768)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
In addition, CONFIG_PPC_8xx also defines CONFIG_CPM1 as
communication co-processor
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
It looks like not many places still have that old CONFIG_8xx used,
so it is likely to be a good time to get rid of it completely ?
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"brd->nasync" amd "brd->maxports" are the same. They hold the number of
filled out channels in the brd->channels[] array. These tests should
be ">=" instead of ">" so that we don't read one element past the end.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cdns_uart_console_setup() checks port->mapbase != 0, but the port may
not be initialized yet even if this condition is met [e.g., ioremap()
may have failed]. Check port->membase != NULL instead, similar to
cdns_early_console_setup().
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Get rid of cdns_uart_readl() and cdns_uart_writel() and just call
readl() and writel() directly.
Most of the patch was created by search-and-replace (I had to convert a
few lines manually, and break some lines longer than 80 columns):
* s/cdns_uart_readl(/readl(port->membase + /g
* s/cdns_uart_writel(\([^,]*\),/writel(\1, port->membase +/g
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cdns_uart_get_port() sets port->iobase = 1 to "mark port in use", but
this "in use" condition is not checked anywhere else in the code. So
remove the line, keeping port->iobase = 0 (which also makes more sense).
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code assumes that the array cdns_uart_port[] has dimension
CDNS_UART_NR_PORTS, so let us define it this way.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The register space size is 0x1000, and this value [not 0xfff] should be
provided to request_mem_region(), ioremap(), etc.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make the 8250 driver reserve exactly the mmio region specified
in the devicetree. This prevents conflicts between UPIO_AU type
UARTs and other devices mapped closer than the default size of
0x1000 (or 0x100 for RT2880).
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds a mapsize field to struct uart_port to be used in
conjunction with mapbase. If set, it overrides whatever value
serial8250_port_size() would otherwise report.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add ACPI identifier for UART on AMD SOC Carrizo.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current calculation method in the case of 9600bps, rounding error occurs
has become setting that occur timeout faster than the required time. When we
use 9600bps, 32byte buffer, 10 bit (CS8) and 100 HZ, it becomes 3 jiffies
(30msec). In fact it is necessary 33msec. This updates to the calculation
that are not actually less than the value set by the rounding error.
Also, this is nothing will be calculated value when there is no load. If there
are a lot of case load, overrun error will occur immediately.
This is by the buffer size to be calculated twice the DMA buffer, and add the
change of setting a sufficient time-out value.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SCIFA and SCIFB can detect the overrun, but it does not support.
This adds overrun handling of SCIFA and SCIFB.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Although clk_disable_unprepare() is called both on .remove()
and in .probe() error path, the clock is never actually enabled.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
EFCR register contains RS-485 configuration which should not
be changed by shutdown. Instead of doing a write only update
the appropriate bits.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If ports are not explicitly removed on the error path
the device will not get properly unregistered leaving
/dev/ttySC* nodes in the filesystem.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When wakeirq is not used/enabled, "no wakeirq for uart0" is output for
all TTY as the log message is generated before the port line is
initialized.
[ 0.802656] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.811700] omap_uart 44e09000.serial: no wakeirq for uart0
[ 0.812379] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[ 1.503622] console [ttyO0] enabled
[ 1.509836] omap_uart 48022000.serial: no wakeirq for uart0
[ 1.516118] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[ 1.527711] omap_uart 48024000.serial: no wakeirq for uart0
[ 1.533881] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[ 1.545324] omap_uart 481a6000.serial: no wakeirq for uart0
[ 1.551410] 481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 60, base_baud = 3000000) is a OMAP UART3
[ 1.562946] omap_uart 481a8000.serial: no wakeirq for uart0
[ 1.569036] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61, base_baud = 3000000) is a OMAP UART4
Fix by moving wakeirq initialization, check, and dev_info() call to
after port line initialization and validation.
Signed-off-by: Doug Kehn <rdkehn@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver is orphaned now that mach-msm has been removed.
Delete it.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This config no longer exists now that mach-msm has been removed.
Delete it and the associated code.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove pci_fintek_setup() non-used var with calculation ciobase
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The serial_core.h file have been included in header file
serial_8250.h. so remove the "#include <serial_core.h>" in
some 8250 serial drivers, because they have included the header file
serial_8250.h.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Au1x00/RT2800+ doesn't implement the 8250 scratch register (and
this may be true of other h/w currently supported by the 8250 driver);
read back the canary value written to the scratch register to enable
the console h/w restart after resume from system suspend.
Fixes: 4516d50aabedb ("serial: 8250: Use canary to restart console ...")
Reported-by: Mason <slash.tmp@free.fr>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Au1x00/RT2800+ hardware has an alternate register layout which is
remapped with lookup tables by the au_serial_in()/out() i/o accessors.
However, the h/w does not support the complete 8250 register set, and
accesses to unmapped registers cause out-of-bounds lookups. Further,
because the lookup tables are defined by designated initializers, the
tables may contain unmapped entries (although the current tables do not).
Declare fixed-size lookup tables with contiguous initialization for
the complete 8250 register map; unmapped registers are initialized to -1.
Validate the register index (ie., 'offset') is in the range [0, table size).
Return fixed value for unmapped register reads and ignore unmapped register
writes.
Reported-by: Mason <slash.tmp@free.fr>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
