wil6210: boot loader

Introduce boot loader. Instead of the operational firmware,
very small boot loader is burned to the on-board flash. Boot loader
initializes hardware upon reset, and prepares for low power mode.
Boot loader reports MAC address and detects radio chip connected.

Driver loads firmware only when bringing up interface. All information
required to set up network interface, most important is MAC address,
reported by the boot loader

The firmware composed of 2 files:
- wil6210.fw - firmware itself (compiled code + data)
- wil6210.board - board file (various board and radio dependent
  calibrations and parameters)

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

1 files changed, 68 insertions, 36 deletions

diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index b04e0afdcb21..acbbd272a41e 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -29,10 +29,6 @@ bool no_fw_recovery;
 module_param(no_fw_recovery, bool, S_IRUGO | S_IWUSR);
 MODULE_PARM_DESC(no_fw_recovery, " disable automatic FW error recovery");
 
-static bool no_fw_load = true;
-module_param(no_fw_load, bool, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(no_fw_load, " do not download FW, use one in on-card flash.");
-
 /* if not set via modparam, will be set to default value of 1/8 of
  * rx ring size during init flow
  */
@@ -532,6 +528,8 @@ static int wil_target_reset(struct wil6210_priv *wil)
 
 	wil_halt_cpu(wil);
 
+	/* clear all boot loader "ready" bits */
+	W(RGF_USER_BL + offsetof(struct RGF_BL, ready), 0);
 	/* Clear Fw Download notification */
 	C(RGF_USER_USAGE_6, BIT(0));
 
@@ -583,16 +581,16 @@ static int wil_target_reset(struct wil6210_priv *wil)
 	/* TODO: check order here!!! Erez code is different */
 	W(RGF_USER_CLKS_CTL_SW_RST_VEC_0, 0);
 
-	/* wait until device ready. typical time is 200..250 msec */
+	/* wait until device ready. typical time is 20..80 msec */
 	do {
 		msleep(RST_DELAY);
-		x = R(RGF_USER_HW_MACHINE_STATE);
+		x = R(RGF_USER_BL + offsetof(struct RGF_BL, ready));
 		if (delay++ > RST_COUNT) {
-			wil_err(wil, "Reset not completed, hw_state 0x%08x\n",
+			wil_err(wil, "Reset not completed, bl.ready 0x%08x\n",
 				x);
 			return -ETIME;
 		}
-	} while (x != HW_MACHINE_BOOT_DONE);
+	} while (!(x & BIT_BL_READY));
 
 	if (!is_reset_v2)
 		W(RGF_PCIE_LOS_COUNTER_CTL, BIT(8));
@@ -603,11 +601,6 @@ static int wil_target_reset(struct wil6210_priv *wil)
 	return 0;
 }
 
-#undef R
-#undef W
-#undef S
-#undef C
-
 void wil_mbox_ring_le2cpus(struct wil6210_mbox_ring *r)
 {
 	le32_to_cpus(&r->base);
@@ -617,6 +610,32 @@ void wil_mbox_ring_le2cpus(struct wil6210_mbox_ring *r)
 	le32_to_cpus(&r->head);
 }
 
+static int wil_get_bl_info(struct wil6210_priv *wil)
+{
+	struct net_device *ndev = wil_to_ndev(wil);
+	struct RGF_BL bl;
+
+	wil_memcpy_fromio_32(&bl, wil->csr + HOSTADDR(RGF_USER_BL), sizeof(bl));
+	le32_to_cpus(&bl.ready);
+	le32_to_cpus(&bl.version);
+	le32_to_cpus(&bl.rf_type);
+	le32_to_cpus(&bl.baseband_type);
+
+	if (!is_valid_ether_addr(bl.mac_address)) {
+		wil_err(wil, "BL: Invalid MAC %pM\n", bl.mac_address);
+		return -EINVAL;
+	}
+
+	ether_addr_copy(ndev->perm_addr, bl.mac_address);
+	if (!is_valid_ether_addr(ndev->dev_addr))
+		ether_addr_copy(ndev->dev_addr, bl.mac_address);
+	wil_info(wil,
+		 "Boot Loader: ver = %d MAC = %pM RF = 0x%08x bband = 0x%08x\n",
+		 bl.version, bl.mac_address, bl.rf_type, bl.baseband_type);
+
+	return 0;
+}
+
 static int wil_wait_for_fw_ready(struct wil6210_priv *wil)
 {
 	ulong to = msecs_to_jiffies(1000);
@@ -637,7 +656,7 @@ static int wil_wait_for_fw_ready(struct wil6210_priv *wil)
  * After calling this routine, you're expected to reload
  * the firmware.
  */
-int wil_reset(struct wil6210_priv *wil)
+int wil_reset(struct wil6210_priv *wil, bool load_fw)
 {
 	int rc;
 
@@ -675,30 +694,36 @@ int wil_reset(struct wil6210_priv *wil)
 	if (rc)
 		return rc;
 
-	if (!no_fw_load) {
-		wil_info(wil, "Use firmware <%s>\n", WIL_FW_NAME);
+	rc = wil_get_bl_info(wil);
+	if (rc)
+		return rc;
+
+	if (load_fw) {
+		wil_info(wil, "Use firmware <%s> + board <%s>\n", WIL_FW_NAME,
+			 WIL_FW2_NAME);
+
 		wil_halt_cpu(wil);
 		/* Loading f/w from the file */
 		rc = wil_request_firmware(wil, WIL_FW_NAME);
 		if (rc)
 			return rc;
+		rc = wil_request_firmware(wil, WIL_FW2_NAME);
+		if (rc)
+			return rc;
+
+		/* Mark FW as loaded from host */
+		S(RGF_USER_USAGE_6, 1);
 
-		/* clear any interrupts which on-card-firmware may have set */
+		/* clear any interrupts which on-card-firmware
+		 * may have set
+		 */
 		wil6210_clear_irq(wil);
-		{ /* CAF_ICR - clear and mask */
-			u32 a = HOSTADDR(RGF_CAF_ICR) +
-				offsetof(struct RGF_ICR, ICR);
-			u32 m = HOSTADDR(RGF_CAF_ICR) +
-				offsetof(struct RGF_ICR, IMV);
-			u32 icr = ioread32(wil->csr + a);
-
-			iowrite32(icr, wil->csr + a); /* W1C */
-			iowrite32(~0, wil->csr + m);
-			wmb(); /* wait for completion */
-		}
+		/* CAF_ICR - clear and mask */
+		/* it is W1C, clear by writing back same value */
+		S(RGF_CAF_ICR + offsetof(struct RGF_ICR, ICR), 0);
+		W(RGF_CAF_ICR + offsetof(struct RGF_ICR, IMV), ~0);
+
 		wil_release_cpu(wil);
-	} else {
-		wil_info(wil, "Use firmware from on-card flash\n");
 	}
 
 	/* init after reset */
@@ -706,15 +731,22 @@ int wil_reset(struct wil6210_priv *wil)
 	reinit_completion(&wil->wmi_ready);
 	reinit_completion(&wil->wmi_call);
 
-	wil_configure_interrupt_moderation(wil);
-	wil_unmask_irq(wil);
+	if (load_fw) {
+		wil_configure_interrupt_moderation(wil);
+		wil_unmask_irq(wil);
 
-	/* we just started MAC, wait for FW ready */
-	rc = wil_wait_for_fw_ready(wil);
+		/* we just started MAC, wait for FW ready */
+		rc = wil_wait_for_fw_ready(wil);
+	}
 
 	return rc;
 }
 
+#undef R
+#undef W
+#undef S
+#undef C
+
 void wil_fw_error_recovery(struct wil6210_priv *wil)
 {
 	wil_dbg_misc(wil, "starting fw error recovery\n");
@@ -730,7 +762,7 @@ int __wil_up(struct wil6210_priv *wil)
 
 	WARN_ON(!mutex_is_locked(&wil->mutex));
 
-	rc = wil_reset(wil);
+	rc = wil_reset(wil, true);
 	if (rc)
 		return rc;
 
@@ -837,7 +869,7 @@ int __wil_down(struct wil6210_priv *wil)
 	if (!iter)
 		wil_err(wil, "timeout waiting for idle FW/HW\n");
 
-	wil_rx_fini(wil);
+	wil_reset(wil, false);
 
 	return 0;
 }