| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"This is a set of pin control fixes I have collected over the last few
days. Some have rotated more than others in linux-next, but they were
rebased on v3.14-rc5 due to sloppy commit messages. I am quite
convinced that they are all good fixes that only hit this or that
individual driver and not the entire subsystem.
- Fix chained interrupts, interrupt masking and register offset
calculation for the sunxi driver
- Make MSM a bool rather than a tristate to stop build problems to
happen - chained interrupt controllers cannot currently be defined
in modules
- Fix a clock in the PFC driver
- Fix a kernel panic in the sirf driver"
* tag 'pinctrl-v3.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sirf: fix kernel panic in gpio_lock_as_irq
pinctrl: sh-pfc: r8a7791: SD1_CLK fix
pinctrl: msm: make PINCTRL_MSM bool instead of tristate
pinctrl: sunxi: Fix interrupt register offset calculation
pinctrl: sunxi: Fix masking when setting irq type
pinctrl: sunxi: use chained_irq_{enter, exit} for GIC compatibility
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fix from Konrad Rzeszutek Wilk:
"This has exactly one patch for Xen ARM. It sets the dependency to
compile the kernel with MMU enabled - otherwise - the guest won't work
very well"
* tag 'stable/for-linus-3.14-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
ARM: XEN depends on having a MMU
|
|
Pull c6x build fix from Mark Salter:
"Build fix for c6x"
* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
c6x: fix build failure caused by cache.h
|
|
commit 655dada6277991 causes kernel panic, this patch fixes it.
[ 1.197816] [ffffffee] *pgd=0d7fd821, *pte=00000000, *ppte=00000000
[ 1.204070] Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[ 1.209447] Modules linked in:
[ 1.212490] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.0-rc1 #3
[ 1.218737] task: cd03c000 ti: cd040000 task.ti: cd040000
[ 1.224127] PC is at gpiod_lock_as_irq+0xc/0x64
[ 1.228634] LR is at sirfsoc_gpio_irq_startup+0x18/0x44
[ 1.233842] pc : [<c01d3990>] lr : [<c01d1c38>] psr: a0000193
[ 1.233842] sp : cd041d30 ip : 00000000 fp : 00000000
[ 1.245296] r10: 00000000 r9 : cd023db4 r8 : 60000113
[ 1.250505] r7 : 0000003e r6 : cd023dd4 r5 : c06bfa54 r4 : cd023d80
[ 1.257014] r3 : 00000020 r2 : 00000000 r1 : ffffffea r0 : ffffffea
[ 1.263526] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 1.270903] Control: 10c53c7d Table: 00004059 DAC: 00000015
[ 1.276631] Process swapper/0 (pid: 1, stack limit = 0xcd040240)
[ 1.282620] Stack: (0xcd041d30 to 0xcd042000)
[ 1.286963] 1d20: cd023d80 c01d1c38 c01d1c20 cd023d80
[ 1.295124] 1d40: 00000001 c0068438 cd023d80 ccb6d880 cd023dd4 c0067044 0000718e c006719c
[ 1.286963] 1d20: cd023d80 c01d1c38 c01d1c20 cd023d80
[ 1.295124] 1d40: 00000001 c0068438 cd023d80 ccb6d880 cd023dd4 c0067044 0000718e c006719c
[ 1.295124] 1d40: 00000001 c0068438 cd023d80 ccb6d880 cd023dd4 c0067044 0000718e c006719c
[ 1.303283] 1d60: 00000800 00000083 ccb6d880 cd023d80 c02b41d8 00000083 0000003e ccb7c410
[ 1.311442] 1d80: 00000000 c00671dc 00000083 0000003e c02b41d8 cd3dd5c0 0000003e ccb7c634
[ 1.319601] 1da0: cd040030 c00672a8 cd3dd5c0 ccb7c410 ccb6d340 ccb7c410 ccb6d340 cd3dd400
[ 1.327760] 1dc0: cd3dd410 c02b4434 ccb7c410 c01265a8 00000001 cd3dd410 c0687108 00000000
[ 1.335919] 1de0: c0687108 00000000 00000000 c0240170 c0240158 cd3dd410 c06c30d0 c023e8bc
[ 1.344079] 1e00: c023e9d4 00000000 cd3dd410 c023e9d4 c0682150 c023cf88 cd003e98 cd2d50c4
[ 1.352238] 1e20: cd3dd410 cd3dd444 c06822f0 c023e768 cd3dd418 cd3dd410 c06822f0 c023de14
[ 1.360397] 1e40: cd3dd418 00000000 cd3dd410 c023c398 cd041e78 cd041ea8 cd3dd400 cd3dd410
[ 1.368556] 1e60: 00000083 00000000 cd3dd400 cd3dd410 00000083 000000c8 c04e00c8 c023fee8
[ 1.376715] 1e80: 00000000 cd041ea8 cd3dd400 00000001 00000083 c024048c c0435ef8 c0434dec
[ 1.384874] 1ea0: c068da58 c04c6d04 c0682150 c0435ef8 ffffffff 00000000 00000000 c068da58
[ 1.393033] 1ec0: 00000020 00000000 00000000 00000000 c05dabb8 00000007 c068d640 c068d640
[ 1.401193] 1ee0: c04c247c c04c249c 00000000 c00088e8 cd004c00 c043bbb8 cd029180 c03812a0
[ 1.409352] 1f00: 00000000 00000000 60000113 c0673728 60000113 c0673728 00000000 00000000
[ 1.417511] 1f20: cd7fce01 c0390a54 00000065 c003a81c c049e8bc 00000007 cd7fce0e 00000007
[ 1.425670] 1f40: 00000000 c05dabb8 00000007 c068d640 c068d640 c04c050c c04e00c8 00000065
[ 1.433829] 1f60: c04e00c0 c04c0c54 00000007 00000007 c04c050c c037d8fc cd03c000 c004322c
[ 1.441988] 1f80: c0662b40 0000d640 c03737c0 00000000 00000000 00000000 00000000 00000000
[ 1.450147] 1fa0: 00000000 c03737cc 00000000 c000e478 00000000 00000000 00000000 00000000
[ 1.458307] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.466467] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 0002d481 05014092
[ 1.474640] [<c01d3990>] (gpiod_lock_as_irq) from [<c01d1c38>] (sirfsoc_gpio_irq_startup+0x18/0x44)
[ 1.483661] [<c01d1c38>] (sirfsoc_gpio_irq_startup) from [<c0068438>] (irq_startup+0x34/0x6c)
[ 1.492163] [<c0068438>] (irq_startup) from [<c0067044>] (__setup_irq+0x450/0x4b8)
[ 1.499714] [<c0067044>] (__setup_irq) from [<c00671dc>] (request_threaded_irq+0xa8/0x128)
[ 1.507960] [<c00671dc>] (request_threaded_irq) from [<c00672a8>] (request_any_context_irq+0x4c/0x7c)
[ 1.517164] [<c00672a8>] (request_any_context_irq) from [<c02b4434>] (gpio_extcon_probe+0x144/0x1d4)
[ 1.526279] [<c02b4434>] (gpio_extcon_probe) from [<c0240170>] (platform_drv_probe+0x18/0x48)
[ 1.534783] [<c0240170>] (platform_drv_probe) from [<c023e8bc>] (driver_probe_device+0x120/0x238)
[ 1.543641] [<c023e8bc>] (driver_probe_device) from [<c023cf88>] (bus_for_each_drv+0x58/0x8c)
[ 1.552143] [<c023cf88>] (bus_for_each_drv) from [<c023e768>] (device_attach+0x74/0x88)
[ 1.560126] [<c023e768>] (device_attach) from [<c023de14>] (bus_probe_device+0x84/0xa8)
[ 1.568113] [<c023de14>] (bus_probe_device) from [<c023c398>] (device_add+0x440/0x520)
[ 1.576012] [<c023c398>] (device_add) from [<c023fee8>] (platform_device_add+0xb4/0x214)
[ 1.584084] [<c023fee8>] (platform_device_add) from [<c024048c>] (platform_device_register_full+0xb8/0xdc)
[ 1.593719] [<c024048c>] (platform_device_register_full) from [<c04c6d04>] (sirfsoc_init_late+0xec/0xf4)
[ 1.603185] [<c04c6d04>] (sirfsoc_init_late) from [<c04c249c>] (init_machine_late+0x20/0x28)
[ 1.611603] [<c04c249c>] (init_machine_late) from [<c00088e8>] (do_one_initcall+0xf8/0x144)
[ 1.619934] [<c00088e8>] (do_one_initcall) from [<c04c0c54>] (kernel_init_freeable+0x13c/0x1dc)
[ 1.628620] [<c04c0c54>] (kernel_init_freeable) from [<c03737cc>] (kernel_init+0xc/0x118)
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix the SD1_CLK handling for r8a7791. Without this patch
it is impossible to request all pins needed for SDHI1 on
the Koelsch board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Modular builds of pinctrl-msm break due to handle_bad_irq being
unexported for module use. For now, make PINCTRL_MSM 'bool'.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This fixing setting the interrupt type for eints >= 8.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On tha Allwinner A20 SoC, the external interrupts on the pin controller
device are connected to the GIC. Without chained_irq_{enter, exit},
external GPIO interrupts, such as used by mmc core card detect, cause
the system to hang.
This issue was first encountered during my attempt to get out-of-band
interrupts for WiFi on the Cubietruck working. With David's new series
of sunci-mci using mmc slot-gpio for (GPIO interrupt based) card
detection, removing the SD card also causes my Cubietruck to hang. This
problem should extend to all Allwinner A20 based boards.
With this fix, the system no longer hangs when I remove or insert the
SD card. /proc/interrupts show that the interrupt has correctly fired.
However the system still does not detect card removal/insertion. I
believe this is another unrelated issue.
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A patch to linux/irqflags.h uncovered a problem with c6x asm/cache.h
which causes a build failure:
/arch/c6x/include/asm/cache.h:63:20: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘c6x_cache_init’
extern void __init c6x_cache_init(void);
The asm/cache.h was relying on linux/irqflags.h to pull in linux/init.h
but the recent patch changed that. The c6x header should have included
linux/init.h all along.
Signed-off-by: Mark Salter <msalter@redhat.com>
|
|
Pull networking fixes from David Miller:
1) Fix memory leak in ieee80211_prep_connection(), sta_info leaked on
error. From Eytan Lifshitz.
2) Unintentional switch case fallthrough in nft_reject_inet_eval(),
from Patrick McHardy.
3) Must check if payload lenth is a power of 2 in
nft_payload_select_ops(), from Nikolay Aleksandrov.
4) Fix mis-checksumming in xen-netfront driver, ip_hdr() is not in the
correct place when we invoke skb_checksum_setup(). From Wei Liu.
5) TUN driver should not advertise HW vlan offload features in
vlan_features. Fix from Fernando Luis Vazquez Cao.
6) IPV6_VTI needs to select NET_IPV_TUNNEL to avoid build errors, fix
from Steffen Klassert.
7) Add missing locking in xfrm_migrade_state_find(), we must hold the
per-namespace xfrm_state_lock while traversing the lists. Fix from
Steffen Klassert.
8) Missing locking in ath9k driver, access to tid->sched must be done
under ath_txq_lock(). Fix from Stanislaw Gruszka.
9) Fix two bugs in TCP fastopen. First respect the size argument given
to tcp_sendmsg() in the fastopen path, and secondly prevent
tcp_send_syn_data() from potentially using order-5 allocations.
From Eric Dumazet.
10) Fix handling of default neigh garbage collection params, from Jiri
Pirko.
11) Fix cwnd bloat and over-inflation of RTT when transmit segmentation
is in use. From Eric Dumazet.
12) Missing initialization of Realtek r8169 driver's statistics
seqlocks. Fix from Kyle McMartin.
13) Fix RTNL assertion failures in 802.3ad and AB ARP monitor of bonding
driver, from Ding Tianhong.
14) Bonding slave release race can cause divide by zero, fix from
Nikolay Aleksandrov.
15) Overzealous return from neigh_periodic_work() causes reachability
time to not be computed. Fix from Duain Jiong.
16) Fix regression in ipv6_find_hdr(), it should not return -ENOENT when
a specific target is specified and found. From Hans Schillstrom.
17) Fix VLAN tag stripping regression in BNA driver, from Ivan Vecera.
18) Tail loss probe can calculate bogus RTTs due to missing packet
marking on retransmit. Fix from Yuchung Cheng.
19) We cannot do skb_dst_drop() in iptunnel_pull_header() because
multicast loopback detection in later code paths need access to
skb_rtable(). Fix from Xin Long.
20) The macvlan driver regresses in that it propagates lower device
offload support disables into itself, causing severe slowdowns when
running over a bridge. Provide the software offloads always on
macvlan devices to deal with this and the regression is gone. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
macvlan: Add support for 'always_on' offload features
net: sctp: fix sctp_sf_do_5_1D_ce to verify if we/peer is AUTH capable
ip_tunnel:multicast process cause panic due to skb->_skb_refdst NULL pointer
net: cpsw: fix cpdma rx descriptor leak on down interface
be2net: isolate TX workarounds not applicable to Skyhawk-R
be2net: Fix skb double free in be_xmit_wrokarounds() failure path
be2net: clear promiscuous bits in adapter->flags while disabling promiscuous mode
be2net: Fix to reset transparent vlan tagging
qlcnic: dcb: a couple off by one bugs
tcp: fix bogus RTT on special retransmission
hsr: off by one sanity check in hsr_register_frame_in()
can: remove CAN FD compatibility for CAN 2.0 sockets
can: flexcan: factor out soft reset into seperate funtion
can: flexcan: flexcan_remove(): add missing netif_napi_del()
can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze
can: flexcan: factor out transceiver {en,dis}able into seperate functions
can: flexcan: fix transition from and to low power mode in chip_{en,dis}able
can: flexcan: flexcan_open(): fix error path if flexcan_chip_start() fails
can: flexcan: fix shutdown: first disable chip, then all interrupts
USB AX88179/178A: Support D-Link DUB-1312
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes here which ensure that regulators using the core
support for GPIO enables work in all cases by ensuring that helpers
are used consistently rather than open coding in places and hence not
having GPIO support in some of them"
* tag 'regulator-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Replace direct ops->disable usage
regulator: core: Replace direct ops->enable usage
|
|
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton akpm@linux-foundation.org>:
mm: page_alloc: exempt GFP_THISNODE allocations from zone fairness
mm: numa: bugfix for LAST_CPUPID_NOT_IN_PAGE_FLAGS
MAINTAINERS: add and correct types of some "T:" entries
MAINTAINERS: use tab for separator
rapidio/tsi721: fix tasklet termination in dma channel release
hfsplus: fix remount issue
zram: avoid null access when fail to alloc meta
sh: prefix sh-specific "CCR" and "CCR2" by "SH_"
ocfs2: fix quota file corruption
drivers/rtc/rtc-s3c.c: fix incorrect way of save/restore of S3C2410_TICNT for TYPE_S3C64XX
kallsyms: fix absolute addresses for kASLR
scripts/gen_initramfs_list.sh: fix flags for initramfs LZ4 compression
mm: include VM_MIXEDMAP flag in the VM_SPECIAL list to avoid m(un)locking
memcg: reparent charges of children before processing parent
memcg: fix endless loop in __mem_cgroup_iter_next()
lib/radix-tree.c: swapoff tmpfs radix_tree: remember to rcu_read_unlock
dma debug: account for cachelines and read-only mappings in overlap tracking
mm: close PageTail race
MAINTAINERS: EDAC: add Mauro and Borislav as interim patch collectors
|
|
Jan Stancek reports manual page migration encountering allocation
failures after some pages when there is still plenty of memory free, and
bisected the problem down to commit 81c0a2bb515f ("mm: page_alloc: fair
zone allocator policy").
The problem is that GFP_THISNODE obeys the zone fairness allocation
batches on one hand, but doesn't reset them and wake kswapd on the other
hand. After a few of those allocations, the batches are exhausted and
the allocations fail.
Fixing this means either having GFP_THISNODE wake up kswapd, or
GFP_THISNODE not participating in zone fairness at all. The latter
seems safer as an acute bugfix, we can clean up later.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When doing some numa tests on powerpc, I triggered an oops bug. I find
it is caused by using page->_last_cpupid. It should be initialized as
"-1 & LAST_CPUPID_MASK", but not "-1". Otherwise, in task_numa_fault(),
we will miss the checking (last_cpupid == (-1 & LAST_CPUPID_MASK)). And
finally cause an oops bug in task_numa_group(), since the online cpu is
less than possible cpu. This happen with CONFIG_SPARSE_VMEMMAP disabled
Call trace:
SMP NR_CPUS=64 NUMA PowerNV
Modules linked in:
CPU: 24 PID: 804 Comm: systemd-udevd Not tainted3.13.0-rc1+ #32
task: c000001e2746aa80 ti: c000001e32c50000 task.ti:c000001e32c50000
REGS: c000001e32c53510 TRAP: 0300 Not tainted(3.13.0-rc1+)
MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR:28024424 XER: 20000000
CFAR: c000000000009324 DAR: 7265717569726857 DSISR:40000000 SOFTE: 1
NIP .task_numa_fault+0x1470/0x2370
LR .task_numa_fault+0x1468/0x2370
Call Trace:
.task_numa_fault+0x1468/0x2370 (unreliable)
.do_numa_page+0x480/0x4a0
.handle_mm_fault+0x4ec/0xc90
.do_page_fault+0x3a8/0x890
handle_page_fault+0x10/0x30
Instruction dump:
3c82fefb 3884b138 48d9cff1 60000000 48000574 3c62fefb3863af78 3c82fefb
3884b138 48d9cfd5 60000000 e93f0100 <812902e4> 7d2907b45529063e 7d2a07b4
---[ end trace 15f2510da5ae07cf ]---
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tree location entries should start with the appropriate type.
Add git to some, hg to another.
Neaten tree type description.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert whitespace to single tab for separators.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch is a modification of the patch originally proposed by
Xiaotian Feng <xtfeng@gmail.com>: https://lkml.org/lkml/2012/11/5/413
This new version disables DMA channel interrupts and ensures that the
tasklet wil not be scheduled again before calling tasklet_kill().
Unfortunately the updated patch was not released at that time due to
planned rework of Tsi721 mport driver to use threaded interrupts (which
has yet to happen). Recently the issue was reported again:
https://lkml.org/lkml/2014/2/19/762.
Description from the original Xiaotian's patch:
"Some drivers use tasklet_disable in device remove/release process,
tasklet_disable will inc tasklet->count and return. If the tasklet is
not handled yet under some softirq pressure, the tasklet will be
placed on the tasklet_vec, never have a chance to be excuted. This
might lead to a heavy loaded ksoftirqd, wakeup with pending_softirq,
but tasklet is disabled. tasklet_kill should be used in this case."
This patch is applicable to kernel versions starting from v3.5.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: <stable@vger.kernel.org> [3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Current implementation of HFS+ driver has small issue with remount
option. Namely, for example, you are unable to remount from RO mode
into RW mode by means of command "mount -o remount,rw /dev/loop0
/mnt/hfsplus". Trying to execute sequence of commands results in an
error message:
mount /dev/loop0 /mnt/hfsplus
mount -o remount,ro /dev/loop0 /mnt/hfsplus
mount -o remount,rw /dev/loop0 /mnt/hfsplus
mount: you must specify the filesystem type
mount -t hfsplus -o remount,rw /dev/loop0 /mnt/hfsplus
mount: /mnt/hfsplus not mounted or bad option
The reason of such issue is failure of mount syscall:
mount("/dev/loop0", "/mnt/hfsplus", 0x2282a60, MS_MGC_VAL|MS_REMOUNT, NULL) = -1 EINVAL (Invalid argument)
Namely, hfsplus_parse_options_remount() method receives empty "input"
argument and return false in such case. As a result, hfsplus_remount()
returns -EINVAL error code.
This patch fixes the issue by means of return true for the case of empty
"input" argument in hfsplus_parse_options_remount() method.
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
zram_meta_alloc could fail so caller should check it. Otherwise, your
system will hang.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit bcf24e1daa94 ("mmc: omap_hsmmc: use the generic config for
omap2plus devices"), enabled the build for other platforms for compile
testing.
sh-allmodconfig now fails with:
include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant
make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1
This happens because SuperH #defines "CCR", which is one of the enum
values in include/linux/omap-dma.h. There's a similar issue with "CCR2"
on sh2a.
As "CCR" and "CCR2" are too generic names for global #defines, prefix
them with "SH_" to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Global quota files are accessed from different nodes. Thus we cannot
cache offset of quota structure in the quota file after we drop our node
reference count to it because after that moment quota structure may be
freed and reallocated elsewhere by a different node resulting in
corruption of quota file.
Fix the problem by clearing dq_off when we are releasing dquot structure.
We also remove the DB_READ_B handling because it is useless -
DQ_ACTIVE_B is set iff DQ_READ_B is set.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Goldwyn Rodrigues <rgoldwyn@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
for TYPE_S3C64XX
On exynos5250, exynos5420 and exynos5260 it was observed that, after 1
cycle of S2R, the rtc-tick occurs at a very fast rate as compared to the
rtc-tick occuring before S2R.
This patch fixes the above issue by correcting the wrong way of
save/restore of S3C2410_TICNT for TYPE_S3C64XX.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently symbols that are absolute addresses are incorrectly displayed
in /proc/kallsyms if the kernel is loaded with kASLR.
The problem was that the scripts/kallsyms.c file which generates the
array of symbol names and addresses uses an relocatable value for all
symbols, even absolute symbols. This patch fixes that.
Several kallsyms output in different boot states for comparison:
$ egrep '_(stext|_per_cpu_(start|end))' /root/kallsyms.nokaslr
0000000000000000 D __per_cpu_start
0000000000014280 D __per_cpu_end
ffffffff810001c8 T _stext
$ egrep '_(stext|_per_cpu_(start|end))' /root/kallsyms.kaslr1
000000001f200000 D __per_cpu_start
000000001f214280 D __per_cpu_end
ffffffffa02001c8 T _stext
$ egrep '_(stext|_per_cpu_(start|end))' /root/kallsyms.kaslr2
000000000d400000 D __per_cpu_start
000000000d414280 D __per_cpu_end
ffffffff8e4001c8 T _stext
$ egrep '_(stext|_per_cpu_(start|end))' /root/kallsyms.kaslr-fixed
0000000000000000 D __per_cpu_start
0000000000014280 D __per_cpu_end
ffffffffadc001c8 T _stext
Signed-off-by: Andy Honig <ahonig@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
LZ4 as implemented in the kernel differs from the default method now
used by the reference implementation of LZ4. Until the in-kernel method
is updated to support the new default, passing the legacy flag (-l) to
the compressor is necessary. Without this flag the kernel-generated,
LZ4-compressed initramfs is junk.
Kyungsik said:
: It seems that lz4 supports legacy format with the same option as lz4c
: does. Just looking at the first few bytes of lz4 compressed image, we can
: see whether it is new format or not.
:
: It shows new format magic number without this patch. New format magic
: number is 0x184d2204.
:
: $ hexdump -C ./initramfs_data.cpio.lz4 |more
: 00000000 04 22 4d 18 64 70 b9 69 (Little Endian)
: ...
:
: Currently kernel supports legacy format only.
Signed-off-by: Daniel M. Weeks <dan@danweeks.net>
Cc: Michal Marek <mmarek@suse.cz>
Acked-by: Kyungsik Lee <kyungsik.lee@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Daniel Borkmann reported a VM_BUG_ON assertion failing:
------------[ cut here ]------------
kernel BUG at mm/mlock.c:528!
invalid opcode: 0000 [#1] SMP
Modules linked in: ccm arc4 iwldvm [...]
video
CPU: 3 PID: 2266 Comm: netsniff-ng Not tainted 3.14.0-rc2+ #8
Hardware name: LENOVO 2429BP3/2429BP3, BIOS G4ET37WW (1.12 ) 05/29/2012
task: ffff8801f87f9820 ti: ffff88002cb44000 task.ti: ffff88002cb44000
RIP: 0010:[<ffffffff81171ad0>] [<ffffffff81171ad0>] munlock_vma_pages_range+0x2e0/0x2f0
Call Trace:
do_munmap+0x18f/0x3b0
vm_munmap+0x41/0x60
SyS_munmap+0x22/0x30
system_call_fastpath+0x1a/0x1f
RIP munlock_vma_pages_range+0x2e0/0x2f0
---[ end trace a0088dcf07ae10f2 ]---
because munlock_vma_pages_range() thinks it's unexpectedly in the middle
of a THP page. This can be reproduced with default config since 3.11
kernels. A reproducer can be found in the kernel's selftest directory
for networking by running ./psock_tpacket.
The problem is that an order=2 compound page (allocated by
alloc_one_pg_vec_page() is part of the munlocked VM_MIXEDMAP vma (mapped
by packet_mmap()) and mistaken for a THP page and assumed to be order=9.
The checks for THP in munlock came with commit ff6a6da60b89 ("mm:
accelerate munlock() treatment of THP pages"), i.e. since 3.9, but did
not trigger a bug. It just makes munlock_vma_pages_range() skip such
compound pages until the next 512-pages-aligned page, when it encounters
a head page. This is however not a problem for vma's where mlocking has
no effect anyway, but it can distort the accounting.
Since commit 7225522bb429 ("mm: munlock: batch non-THP page isolation
and munlock+putback using pagevec") this can trigger a VM_BUG_ON in
PageTransHuge() check.
This patch fixes the issue by adding VM_MIXEDMAP flag to VM_SPECIAL, a
list of flags that make vma's non-mlockable and non-mergeable. The
reasoning is that VM_MIXEDMAP vma's are similar to VM_PFNMAP, which is
already on the VM_SPECIAL list, and both are intended for non-LRU pages
where mlocking makes no sense anyway. Related Lkml discussion can be
found in [2].
[1] tools/testing/selftests/net/psock_tpacket
[2] https://lkml.org/lkml/2014/1/10/427
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Reported-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: John David Anglin <dave.anglin@bell.net>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Jared Hulbert <jaredeh@gmail.com>
Tested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org> [3.11.x+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sometimes the cleanup after memcg hierarchy testing gets stuck in
mem_cgroup_reparent_charges(), unable to bring non-kmem usage down to 0.
There may turn out to be several causes, but a major cause is this: the
workitem to offline parent can get run before workitem to offline child;
parent's mem_cgroup_reparent_charges() circles around waiting for the
child's pages to be reparented to its lrus, but it's holding
cgroup_mutex which prevents the child from reaching its
mem_cgroup_reparent_charges().
Further testing showed that an ordered workqueue for cgroup_destroy_wq
is not always good enough: percpu_ref_kill_and_confirm's call_rcu_sched
stage on the way can mess up the order before reaching the workqueue.
Instead, when offlining a memcg, call mem_cgroup_reparent_charges() on
all its children (and grandchildren, in the correct order) to have their
charges reparented first.
Fixes: e5fca243abae ("cgroup: use a dedicated workqueue for cgroup destruction")
Signed-off-by: Filipe Brandenburger <filbranden@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [v3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 0eef615665ed ("memcg: fix css reference leak and endless loop in
mem_cgroup_iter") got the interaction with the commit a few before it
d8ad30559715 ("mm/memcg: iteration skip memcgs not yet fully
initialized") slightly wrong, and we didn't notice at the time.
It's elusive, and harder to get than the original, but for a couple of
days before rc1, I several times saw a endless loop similar to that
supposedly being fixed.
This time it was a tighter loop in __mem_cgroup_iter_next(): because we
can get here when our root has already been offlined, and the ordering
of conditions was such that we then just cycled around forever.
Fixes: 0eef615665ed ("memcg: fix css reference leak and endless loop in mem_cgroup_iter").
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Greg Thelen <gthelen@google.com>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Running fsx on tmpfs with concurrent memhog-swapoff-swapon, lots of
BUG: sleeping function called from invalid context at kernel/fork.c:606
in_atomic(): 0, irqs_disabled(): 0, pid: 1394, name: swapoff
1 lock held by swapoff/1394:
#0: (rcu_read_lock){.+.+.+}, at: [<ffffffff812520a1>] radix_tree_locate_item+0x1f/0x2b6
followed by
================================================
[ BUG: lock held when returning to user space! ]
3.14.0-rc1 #3 Not tainted
------------------------------------------------
swapoff/1394 is leaving the kernel with locks still held!
1 lock held by swapoff/1394:
#0: (rcu_read_lock){.+.+.+}, at: [<ffffffff812520a1>] radix_tree_locate_item+0x1f/0x2b6
after which the system recovered nicely.
Whoops, I long ago forgot the rcu_read_unlock() on one unlikely branch.
Fixes e504f3fdd63d ("tmpfs radix_tree: locate_item to speed up swapoff")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While debug_dma_assert_idle() checks if a given *page* is actively
undergoing dma the valid granularity of a dma mapping is a *cacheline*.
Sander's testing shows that the warning message "DMA-API: exceeded 7
overlapping mappings of pfn..." is falsely triggering. The test is
simply mapping multiple cachelines in a given page.
Ultimately we want overlap tracking to be valid as it is a real api
violation, so we need to track active mappings by cachelines. Update
the active dma tracking to use the page-frame-relative cacheline of the
mapping as the key, and update debug_dma_assert_idle() to check for all
possible mapped cachelines for a given page.
However, the need to track active mappings is only relevant when the
dma-mapping is writable by the device. In fact it is fairly standard
for read-only mappings to have hundreds or thousands of overlapping
mappings at once. Limiting the overlap tracking to writable
(!DMA_TO_DEVICE) eliminates this class of false-positive overlap
reports.
Note, the radix gang lookup is sub-optimal. It would be best if it
stopped fetching entries once the search passed a page boundary.
Nevertheless, this implementation does not perturb the original net_dma
failing case. That is to say the extra overhead does not show up in
terms of making the failing case pass due to a timing change.
References:
http://marc.info/?l=linux-netdev&m=139232263419315&w=2
http://marc.info/?l=linux-netdev&m=139217088107122&w=2
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit bf6bddf1924e ("mm: introduce compaction and migration for
ballooned pages") introduces page_count(page) into memory compaction
which dereferences page->first_page if PageTail(page).
This results in a very rare NULL pointer dereference on the
aforementioned page_count(page). Indeed, anything that does
compound_head(), including page_count() is susceptible to racing with
prep_compound_page() and seeing a NULL or dangling page->first_page
pointer.
This patch uses Andrea's implementation of compound_trans_head() that
deals with such a race and makes it the default compound_head()
implementation. This includes a read memory barrier that ensures that
if PageTail(head) is true that we return a head page that is neither
NULL nor dangling. The patch then adds a store memory barrier to
prep_compound_page() to ensure page->first_page is set.
This is the safest way to ensure we see the head page that we are
expecting, PageTail(page) is already in the unlikely() path and the
memory barriers are unfortunately required.
Hugetlbfs is the exception, we don't enforce a store memory barrier
during init since no race is possible.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Holger Kiehl <Holger.Kiehl@dwd.de>
Cc: Christoph Lameter <cl@linux.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We're more or less collecting EDAC patches already anyway so let's hold it
down so that get_maintainer sees it too.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Macvlan currently inherits all of its features from the lower
device. When lower device disables offload support, this causes
macvlan to disable offload support as well. This causes
performance regression when using macvlan/macvtap in bridge
mode.
It can be easily demonstrated by creating 2 namespaces using
macvlan in bridge mode and running netperf between them:
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 20.00 1204.61
To restore the performance, we add software offload features
to the list of "always_on" features for macvlan. This way
when a namespace or a guest using macvtap initially sends a
packet, this packet will not be segmented at macvlan level.
It will only be segmented when macvlan sends the packet
to the lower device.
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 20.00 5507.35
Fixes: 6acf54f1cf0a6747bac9fea26f34cfc5a9029523 (macvtap: Add support of packet capture on macvtap device.)
Fixes: 797f87f83b60685ff8a13fa0572d2f10393c50d3 (macvlan: fix netdev feature propagation from lower device)
CC: Florian Westphal <fw@strlen.de>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.14 stream...
For the mac80211 bits, Johannes says:
"This time I have a fix to get out of an 'infinite error state' in case
regulatory domain updates failed and two fixes for VHT associations: one
to not disconnect immediately when the AP uses more bandwidth than the
new regdomain would allow after a change due to association country
information getting used, and one for an issue in the code where
mac80211 doesn't correctly ignore a reserved field and then uses an HT
instead of VHT association."
For the iwlwifi bits, Emmanuel says:
"Johannes fixes a long standing bug in the AMPDU status reporting.
Max fixes the listen time which was way too long and causes trouble
to several APs."
Along with those, Bing Zhao marks the mwifiex_usb driver as _not_
supporting USB autosuspend after a number of problems with that have
been reported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC4895 introduced AUTH chunks for SCTP; during the SCTP
handshake RANDOM; CHUNKS; HMAC-ALGO are negotiated (CHUNKS
being optional though):
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
-------------------- COOKIE-ECHO -------------------->
<-------------------- COOKIE-ACK ---------------------
A special case is when an endpoint requires COOKIE-ECHO
chunks to be authenticated:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
------------------ AUTH; COOKIE-ECHO ---------------->
<-------------------- COOKIE-ACK ---------------------
RFC4895, section 6.3. Receiving Authenticated Chunks says:
The receiver MUST use the HMAC algorithm indicated in
the HMAC Identifier field. If this algorithm was not
specified by the receiver in the HMAC-ALGO parameter in
the INIT or INIT-ACK chunk during association setup, the
AUTH chunk and all the chunks after it MUST be discarded
and an ERROR chunk SHOULD be sent with the error cause
defined in Section 4.1. [...] If no endpoint pair shared
key has been configured for that Shared Key Identifier,
all authenticated chunks MUST be silently discarded. [...]
When an endpoint requires COOKIE-ECHO chunks to be
authenticated, some special procedures have to be followed
because the reception of a COOKIE-ECHO chunk might result
in the creation of an SCTP association. If a packet arrives
containing an AUTH chunk as a first chunk, a COOKIE-ECHO
chunk as the second chunk, and possibly more chunks after
them, and the receiver does not have an STCB for that
packet, then authentication is based on the contents of
the COOKIE-ECHO chunk. In this situation, the receiver MUST
authenticate the chunks in the packet by using the RANDOM
parameters, CHUNKS parameters and HMAC_ALGO parameters
obtained from the COOKIE-ECHO chunk, and possibly a local
shared secret as inputs to the authentication procedure
specified in Section 6.3. If authentication fails, then
the packet is discarded. If the authentication is successful,
the COOKIE-ECHO and all the chunks after the COOKIE-ECHO
MUST be processed. If the receiver has an STCB, it MUST
process the AUTH chunk as described above using the STCB
from the existing association to authenticate the
COOKIE-ECHO chunk and all the chunks after it. [...]
Commit bbd0d59809f9 introduced the possibility to receive
and verification of AUTH chunk, including the edge case for
authenticated COOKIE-ECHO. On reception of COOKIE-ECHO,
the function sctp_sf_do_5_1D_ce() handles processing,
unpacks and creates a new association if it passed sanity
checks and also tests for authentication chunks being
present. After a new association has been processed, it
invokes sctp_process_init() on the new association and
walks through the parameter list it received from the INIT
chunk. It checks SCTP_PARAM_RANDOM, SCTP_PARAM_HMAC_ALGO
and SCTP_PARAM_CHUNKS, and copies them into asoc->peer
meta data (peer_random, peer_hmacs, peer_chunks) in case
sysctl -w net.sctp.auth_enable=1 is set. If in INIT's
SCTP_PARAM_SUPPORTED_EXT parameter SCTP_CID_AUTH is set,
peer_random != NULL and peer_hmacs != NULL the peer is to be
assumed asoc->peer.auth_capable=1, in any other case
asoc->peer.auth_capable=0.
Now, if in sctp_sf_do_5_1D_ce() chunk->auth_chunk is
available, we set up a fake auth chunk and pass that on to
sctp_sf_authenticate(), which at latest in
sctp_auth_calculate_hmac() reliably dereferences a NULL pointer
at position 0..0008 when setting up the crypto key in
crypto_hash_setkey() by using asoc->asoc_shared_key that is
NULL as condition key_id == asoc->active_key_id is true if
the AUTH chunk was injected correctly from remote. This
happens no matter what net.sctp.auth_enable sysctl says.
The fix is to check for net->sctp.auth_enable and for
asoc->peer.auth_capable before doing any operations like
sctp_sf_authenticate() as no key is activated in
sctp_auth_asoc_init_active_key() for each case.
Now as RFC4895 section 6.3 states that if the used HMAC-ALGO
passed from the INIT chunk was not used in the AUTH chunk, we
SHOULD send an error; however in this case it would be better
to just silently discard such a maliciously prepared handshake
as we didn't even receive a parameter at all. Also, as our
endpoint has no shared key configured, section 6.3 says that
MUST silently discard, which we are doing from now onwards.
Before calling sctp_sf_pdiscard(), we need not only to free
the association, but also the chunk->auth_chunk skb, as
commit bbd0d59809f9 created a skb clone in that case.
I have tested this locally by using netfilter's nfqueue and
re-injecting packets into the local stack after maliciously
modifying the INIT chunk (removing RANDOM; HMAC-ALGO param)
and the SCTP packet containing the COOKIE_ECHO (injecting
AUTH chunk before COOKIE_ECHO). Fixed with this patch applied.
Fixes: bbd0d59809f9 ("[SCTP]: Implement the receive and verification of AUTH chunk")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <yasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://gitorious.org/linux-can/linux-can
linux-can-fixes-for-3.14-20140303
Marc Kleine-Budde says:
====================
this is a pull request of 8 patches. Oliver Hartkopp contributes a patch which
removes the CAN FD compatibility for CAN 2.0 sockets, as it turns out that this
compatibility has some conceptual cornercases. The remaining 7 patches are by
me, they address a problem in the flexcan driver. When shutting down the
interface ("ifconfig can0 down") under heavy network load the whole system will
hang. This series reworks the actual sequence in close() and the transition
from and to the low power modes of the CAN controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when ip_tunnel process multicast packets, it may check if the packet is looped
back packet though 'rt_is_output_route(skb_rtable(skb))' in ip_tunnel_rcv(),
but before that , skb->_skb_refdst has been dropped in iptunnel_pull_header(),
so which leads to a panic.
fix the bug: https://bugzilla.kernel.org/show_bug.cgi?id=70681
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a CPDMA RX Descriptor leak that occurs after taking
the interface down when the CPSW is in Dual MAC mode. Previously
the CPSW_ALE port was left open up which causes packets to be received
and processed by the RX interrupt handler and were passed to the
non active network interface where they were ignored.
The fix is for the slave_stop function of the selected interface
to disable the respective CPSW_ALE Port from forwarding packets. This
blocks traffic from being received on the inactive interface.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of TX workarounds in be_xmit_workarounds() routine
are not applicable (and result in HW errors) to Skyhawk-R chip.
Isolate BE3-R/Lancer specific workarounds to a separate routine.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_padto(), skb_share_check() and __vlan_put_tag() routines free
skb when they return an error. This patch fixes be_xmit_workarounds()
to not free skb again in such cases.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mode
We should clear promiscuous bits in adapter->flags while disabling promiscuous
mode. Else we will not put interface back into VLAN promisc mode if the vlans
already added exceeds the maximum limit.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1
and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer.
Hence removing the get_hsw_config call from be_vf_setup() as it's
only use of getting default pvid is no longer needed.
Also do proper housekeeping only if the FW command succeeds.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ->tc_cfg[] array has QLC_DCB_MAX_TC (8) elements so the check is
off by one. These functions are always called with valid values though
so it doesn't affect how the code works.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTT may be bogus with tall loss probe (TLP) when a packet
is retransmitted and latter (s)acked without TCPCB_SACKED_RETRANS flag.
For example, TLP calls __tcp_retransmit_skb() instead of
tcp_retransmit_skb(). The skb timestamps are updated but the sacked
flag is not marked with TCPCB_SACKED_RETRANS. As a result we'll
get bogus RTT in tcp_clean_rtx_queue() or in tcp_sacktag_one() on
spurious retransmission.
The fix is to apply the sticky flag TCP_EVER_RETRANS to enforce Karn's
check on RTT sampling. However this will disable F-RTO if timeout occurs
after TLP, by resetting undo_marker in tcp_enter_loss(). We relax this
check to only if any pending retransmists are still in-flight.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a sanity check and we never pass invalid values so this patch
doesn't change anything. However the node->time_in[] array has
HSR_MAX_SLAVE (2) elements and not HSR_MAX_DEV (3).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes, most of them SCHED_DEADLINE fallout"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Prevent rt_time growth to infinity
sched/deadline: Switch CPU's presence test order
sched/deadline: Cleanup RT leftovers from {inc/dec}_dl_migration
sched: Fix double normalization of vruntime
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull liblockdep fixes from Ingo Molnar:
"A handful of build fixes for liblockdep"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/liblockdep: Use realpath for srctree and objtree
tools/liblockdep: Add a stub for new rcu_is_watching
tools/liblockdep: Mark runtests.sh as executable
tools/liblockdep: Add include directory to allow tests to compile
tools/liblockdep: Fix include of asm/hash.h
tools/liblockdep: Fix initialization code path
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clk framework fixes from Mike Turquette:
"Clock framework and driver fixes, all of which fix user-visible
regressions.
There is a single framework fix that prevents dereferencing a NULL
pointer when calling clk_get. The range of fixes for clock driver
regressions spans memory leak fixes, touching the wrong registers that
cause things to explode, misconfigured clock rates that result in
non-responsive devices and even some boot failures. The most benign
fix is DT binding doc typo. It is a stable ABI exposed from the
kernel that was introduced in -rc1, so best to fix it now"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk:at91: Fix memory leak in of_at91_clk_master_setup()
clk: nomadik: fix multiplatform problem
clk: Correct handling of NULL clk in __clk_{get, put}
clk: shmobile: Fix typo in MSTP clock DT bindings
clk: shmobile: rcar-gen2: Fix qspi divisor
clk: shmobile: rcar-gen2: Fix clock parent for all non-PLL clocks
clk: tegra124: remove gr2d and gr3d clocks
clk: tegra: Fix vic03 mux index
clk: shmobile: rcar-gen2: Fix qspi divisor
clk: shmobile: rcar-gen2: Fix clock parent all non-PLL clocks
clk: tegra: use max divider if divider overflows
clk: tegra: cclk_lp has a pllx/2 divider
clk: tegra: fix sdmmc clks on Tegra1x4
clk: tegra: fix host1x clock on Tegra124
clk: tegra: PLLD2 fixes for hdmi
clk: tegra: Fix PLLD mnp table
clk: tegra: Fix PLLP rate table
clk: tegra: Correct clock number for UARTE
clk: tegra: Add missing Tegra20 fuse clks
ARM: keystone: dts: fix clkvcp3 control register address
...
|
|
arch/arm/xen/enlighten.c (and maybe others) use MMU-specific functions
like pte_mkspecial which are only available on MMU builds. So let XEN
depend on MMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
