arm64: dts: qcom: Add UFS nodes

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

2 files changed, 141 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
index eedfaf8922e2..ed53464c2957 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -417,6 +417,27 @@
 	vdda-pll-supply = <&vdda_usb2_ss_core>;
 };
 
+&ufshc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-voltage-level = <2950000 2960000>;
+	vcc-max-microamp = <600000>;
+	vccq2-max-microamp = <600000>;
+
+	qcom,vddp-ref-clk-supply = <&vreg_l2a_1p2>;
+	qcom,vddp-ref-clk-max-microamp = <100>;
+};
+
+&ufsphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>; /* 0.88v */
+	vdda-pll-supply = <&vreg_l26a_1p2>; /* 1.2v */
+	vdda-phy-max-microamp = <62900>;
+	vdda-pll-max-microamp = <18300>;
+};
+
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
 
 &qup_i2c10_default {
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index b72bdb0a31a5..60cb5af66a1b 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -808,6 +808,84 @@
 			};
 		};
 
+		ufshc: ufshc@1d84000 {
+			compatible = "qcom,ufshc";
+			reg = <0x1d84000 0x2500>;
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufsphy_0>;
+			phy-names = "ufsphy";
+
+			lanes-per-direction = <2>;
+			dev-ref-clk-freq = <0>; /* 19.2 MHz */
+
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
+			clock-names = "core_clk",
+				      "bus_aggr_clk",
+				      "iface_clk",
+				      "core_clk_unipro",
+				      "ref_clk",
+				      "tx_lane0_sync_clk",
+				      "rx_lane0_sync_clk",
+				      "rx_lane1_sync_clk";
+			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
+			         <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_UFS_PHY_AHB_CLK>,
+				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+			freq-table-hz = <50000000 200000000>,
+					<0 0>,
+					<0 0>,
+					<37500000 150000000>,
+					<0 0>,
+					<0 0>,
+					<0 0>,
+					<0 0>;
+
+			non-removable;
+			pinctrl-names = "dev-reset-assert", "dev-reset-deassert";
+			pinctrl-0 = <&ufs_dev_reset_assert>;
+			pinctrl-1 = <&ufs_dev_reset_deassert>;
+
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "core_reset";
+
+			status = "disabled";
+		};
+
+		ufsphy: phy@1d87000 {
+			compatible = "qcom,sdm845-qmp-ufs-phy";
+			reg = <0x1d87000 0x18c>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clock-names = "ref",
+				      "ref_aux";
+			clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
+
+			status = "disabled";
+
+			ufsphy_0: lane@1d87400 {
+				reg = <0x1d87400 0x108>,
+				      <0x1d87600 0x1e0>,
+				      <0x1d87c00 0x1dc>;
+				#phy-cells = <0>;
+			};
+
+			ufsphy_1: lane@1d87800 {
+				reg = <0x1d87800 0x108>,
+				      <0x1d87a00 0x1e0>,
+				      <0x1d87c00 0x1dc>;
+				#phy-cells = <0>;
+			};
+		};
+
 		tcsr_mutex_regs: syscon@1f40000 {
 			compatible = "syscon";
 			reg = <0x1f40000 0x40000>;
@@ -1068,6 +1146,48 @@
 					function = "qup9";
 				};
 			};
+
+			ufs_dev_reset_assert: ufs_dev_reset_assert {
+				pins = "ufs_reset";
+				bias-pull-down;         /* default: pull down */
+				/*
+				 * UFS_RESET driver strengths are having
+				 * different values/steps compared to typical
+				 * GPIO drive strengths.
+				 *
+				 * Following table clarifies:
+				 *
+				 * HDRV value | UFS_RESET | Typical GPIO
+				 *   (dec)    |   (mA)    |    (mA)
+				 *     0      |   0.8     |    2
+				 *     1      |   1.55    |    4
+				 *     2      |   2.35    |    6
+				 *     3      |   3.1     |    8
+				 *     4      |   3.9     |    10
+				 *     5      |   4.65    |    12
+				 *     6      |   5.4     |    14
+				 *     7      |   6.15    |    16
+				 *
+				 * POR value for UFS_RESET HDRV is 3 which means
+				 * 3.1mA and we want to use that. Hence just
+				 * specify 8mA to "drive-strength" binding and
+				 * that should result into writing 3 to HDRV
+				 * field.
+				 */
+				drive-strength = <8>;   /* default: 3.1 mA */
+				output-low; /* active low reset */
+			};
+
+			ufs_dev_reset_deassert: ufs_dev_reset_deassert {
+				pins = "ufs_reset";
+				bias-pull-down;         /* default: pull down */
+				/*
+				 * default: 3.1 mA
+				 * check comments under ufs_dev_reset_assert
+				 */
+				drive-strength = <8>;
+				output-high; /* active low reset */
+			};
 		};
 
 		usb_1_hsphy: phy@88e2000 {