aboutsummaryrefslogtreecommitdiff
path: root/net
AgeCommit message (Collapse)Author
2020-09-04net/packet: fix overflow in tpacket_rcvOr Cohen
Using tp_reserve to calculate netoff can overflow as tp_reserve is unsigned int and netoff is unsigned short. This may lead to macoff receving a smaller value then sizeof(struct virtio_net_hdr), and if po->has_vnet_hdr is set, an out-of-bounds write will occur when calling virtio_net_hdr_from_skb. The bug is fixed by converting netoff to unsigned int and checking if it exceeds USHRT_MAX. This addresses CVE-2020-14386 Fixes: 8913336a7e8d ("packet: add PACKET_RESERVE sockopt") Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-09-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds
Pull networking fixes from David Miller: 1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi Kivilinna. 2) Fix loss of RTT samples in rxrpc, from David Howells. 3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu. 4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka. 5) We disable BH for too lokng in sctp_get_port_local(), add a cond_resched() here as well, from Xin Long. 6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu. 7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from Yonghong Song. 8) Missing of_node_put() in mt7530 DSA driver, from Sumera Priyadarsini. 9) Fix crash in bnxt_fw_reset_task(), from Michael Chan. 10) Fix geneve tunnel checksumming bug in hns3, from Yi Li. 11) Memory leak in rxkad_verify_response, from Dinghao Liu. 12) In tipc, don't use smp_processor_id() in preemptible context. From Tuong Lien. 13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu. 14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter. 15) Fix ABI mismatch between driver and firmware in nfp, from Louis Peens. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits) net/smc: fix sock refcounting in case of termination net/smc: reset sndbuf_desc if freed net/smc: set rx_off for SMCR explicitly net/smc: fix toleration of fake add_link messages tg3: Fix soft lockup when tg3_reset_task() fails. doc: net: dsa: Fix typo in config code sample net: dp83867: Fix WoL SecureOn password nfp: flower: fix ABI mismatch between driver and firmware tipc: fix shutdown() of connectionless socket ipv6: Fix sysctl max for fib_multipath_hash_policy drivers/net/wan/hdlc: Change the default of hard_header_len to 0 net: gemini: Fix another missing clk_disable_unprepare() in probe net: bcmgenet: fix mask check in bcmgenet_validate_flow() amd-xgbe: Add support for new port mode net: usb: dm9601: Add USB ID of Keenetic Plus DSL vhost: fix typo in error message net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init() pktgen: fix error message with wrong function name net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode cxgb4: fix thermal zone device registration ...
2020-09-03net/smc: fix sock refcounting in case of terminationUrsula Braun
When an ISM device is removed, all its linkgroups are terminated, i.e. all the corresponding connections are killed. Connection killing invokes smc_close_active_abort(), which decreases the sock refcount for certain states to simulate passive closing. And it cancels the close worker and has to give up the sock lock for this timeframe. This opens the door for a passive close worker or a socket close to run in between. In this case smc_close_active_abort() and passive close worker resp. smc_release() might do a sock_put for passive closing. This causes: [ 1323.315943] refcount_t: underflow; use-after-free. [ 1323.316055] WARNING: CPU: 3 PID: 54469 at lib/refcount.c:28 refcount_warn_saturate+0xe8/0x130 [ 1323.316069] Kernel panic - not syncing: panic_on_warn set ... [ 1323.316084] CPU: 3 PID: 54469 Comm: uperf Not tainted 5.9.0-20200826.rc2.git0.46328853ed20.300.fc32.s390x+debug #1 [ 1323.316096] Hardware name: IBM 2964 NC9 702 (z/VM 6.4.0) [ 1323.316108] Call Trace: [ 1323.316125] [<00000000c0d4aae8>] show_stack+0x90/0xf8 [ 1323.316143] [<00000000c15989b0>] dump_stack+0xa8/0xe8 [ 1323.316158] [<00000000c0d8344e>] panic+0x11e/0x288 [ 1323.316173] [<00000000c0d83144>] __warn+0xac/0x158 [ 1323.316187] [<00000000c1597a7a>] report_bug+0xb2/0x130 [ 1323.316201] [<00000000c0d36424>] monitor_event_exception+0x44/0xc0 [ 1323.316219] [<00000000c195c716>] pgm_check_handler+0x1da/0x238 [ 1323.316234] [<00000000c151844c>] refcount_warn_saturate+0xec/0x130 [ 1323.316280] ([<00000000c1518448>] refcount_warn_saturate+0xe8/0x130) [ 1323.316310] [<000003ff801f2e2a>] smc_release+0x192/0x1c8 [smc] [ 1323.316323] [<00000000c169f1fa>] __sock_release+0x5a/0xe0 [ 1323.316334] [<00000000c169f2ac>] sock_close+0x2c/0x40 [ 1323.316350] [<00000000c1086de0>] __fput+0xb8/0x278 [ 1323.316362] [<00000000c0db1e0e>] task_work_run+0x76/0xb8 [ 1323.316393] [<00000000c0d8ab84>] do_exit+0x26c/0x520 [ 1323.316408] [<00000000c0d8af08>] do_group_exit+0x48/0xc0 [ 1323.316421] [<00000000c0d8afa8>] __s390x_sys_exit_group+0x28/0x38 [ 1323.316433] [<00000000c195c32c>] system_call+0xe0/0x2b4 [ 1323.316446] 1 lock held by uperf/54469: [ 1323.316456] #0: 0000000044125e60 (&sb->s_type->i_mutex_key#9){+.+.}-{3:3}, at: __sock_release+0x44/0xe0 The patch rechecks sock state in smc_close_active_abort() after smc_close_cancel_work() to avoid duplicate decrease of sock refcount for the same purpose. Fixes: 611b63a12732 ("net/smc: cancel tx worker in case of socket aborts") Reviewed-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-03net/smc: reset sndbuf_desc if freedUrsula Braun
When an SMC connection is created, and there is a problem to create an RMB or DMB, the previously created send buffer is thrown away as well including buffer descriptor freeing. Make sure the connection no longer references the freed buffer descriptor, otherwise bugs like this are possible: [71556.835148] ============================================================================= [71556.835168] BUG kmalloc-128 (Tainted: G B OE ): Poison overwritten [71556.835172] ----------------------------------------------------------------------------- [71556.835179] INFO: 0x00000000d20894be-0x00000000aaef63e9 @offset=2724. First byte 0x0 instead of 0x6b [71556.835215] INFO: Allocated in __smc_buf_create+0x184/0x578 [smc] age=0 cpu=5 pid=46726 [71556.835234] ___slab_alloc+0x5a4/0x690 [71556.835239] __slab_alloc.constprop.0+0x70/0xb0 [71556.835243] kmem_cache_alloc_trace+0x38e/0x3f8 [71556.835250] __smc_buf_create+0x184/0x578 [smc] [71556.835257] smc_buf_create+0x2e/0xe8 [smc] [71556.835264] smc_listen_work+0x516/0x6a0 [smc] [71556.835275] process_one_work+0x280/0x478 [71556.835280] worker_thread+0x66/0x368 [71556.835287] kthread+0x17a/0x1a0 [71556.835294] ret_from_fork+0x28/0x2c [71556.835301] INFO: Freed in smc_buf_create+0xd8/0xe8 [smc] age=0 cpu=5 pid=46726 [71556.835307] __slab_free+0x246/0x560 [71556.835311] kfree+0x398/0x3f8 [71556.835318] smc_buf_create+0xd8/0xe8 [smc] [71556.835324] smc_listen_work+0x516/0x6a0 [smc] [71556.835328] process_one_work+0x280/0x478 [71556.835332] worker_thread+0x66/0x368 [71556.835337] kthread+0x17a/0x1a0 [71556.835344] ret_from_fork+0x28/0x2c [71556.835348] INFO: Slab 0x00000000a0744551 objects=51 used=51 fp=0x0000000000000000 flags=0x1ffff00000010200 [71556.835352] INFO: Object 0x00000000563480a1 @offset=2688 fp=0x00000000289567b2 [71556.835359] Redzone 000000006783cde2: bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb ................ [71556.835363] Redzone 00000000e35b876e: bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb ................ [71556.835367] Redzone 0000000023074562: bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb ................ [71556.835372] Redzone 00000000b9564b8c: bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb ................ [71556.835376] Redzone 00000000810c6362: bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb ................ [71556.835380] Redzone 0000000065ef52c3: bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb ................ [71556.835384] Redzone 00000000c5dd6984: bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb ................ [71556.835388] Redzone 000000004c480f8f: bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb ................ [71556.835392] Object 00000000563480a1: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk [71556.835397] Object 000000009c479d06: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk [71556.835401] Object 000000006e1dce92: 6b 6b 6b 6b 00 00 00 00 6b 6b 6b 6b 6b 6b 6b 6b kkkk....kkkkkkkk [71556.835405] Object 00000000227f7cf8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk [71556.835410] Object 000000009a701215: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk [71556.835414] Object 000000003731ce76: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk [71556.835418] Object 00000000f7085967: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk [71556.835422] Object 0000000007f99927: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkkkkkkkkkk. [71556.835427] Redzone 00000000579c4913: bb bb bb bb bb bb bb bb ........ [71556.835431] Padding 00000000305aef82: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ [71556.835435] Padding 00000000b1cdd722: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ [71556.835438] Padding 00000000c7568199: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ [71556.835442] Padding 00000000fad4c4d4: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ [71556.835451] CPU: 0 PID: 47939 Comm: kworker/0:15 Tainted: G B OE 5.9.0-rc1uschi+ #54 [71556.835456] Hardware name: IBM 3906 M03 703 (LPAR) [71556.835464] Workqueue: events smc_listen_work [smc] [71556.835470] Call Trace: [71556.835478] [<00000000d5eaeb10>] show_stack+0x90/0xf8 [71556.835493] [<00000000d66fc0f8>] dump_stack+0xa8/0xe8 [71556.835499] [<00000000d61a511c>] check_bytes_and_report+0x104/0x130 [71556.835504] [<00000000d61a57b2>] check_object+0x26a/0x2e0 [71556.835509] [<00000000d61a59bc>] alloc_debug_processing+0x194/0x238 [71556.835514] [<00000000d61a8c14>] ___slab_alloc+0x5a4/0x690 [71556.835519] [<00000000d61a9170>] __slab_alloc.constprop.0+0x70/0xb0 [71556.835524] [<00000000d61aaf66>] kmem_cache_alloc_trace+0x38e/0x3f8 [71556.835530] [<000003ff80549bbc>] __smc_buf_create+0x184/0x578 [smc] [71556.835538] [<000003ff8054a396>] smc_buf_create+0x2e/0xe8 [smc] [71556.835545] [<000003ff80540c16>] smc_listen_work+0x516/0x6a0 [smc] [71556.835549] [<00000000d5f0f448>] process_one_work+0x280/0x478 [71556.835554] [<00000000d5f0f6a6>] worker_thread+0x66/0x368 [71556.835559] [<00000000d5f18692>] kthread+0x17a/0x1a0 [71556.835563] [<00000000d6abf3b8>] ret_from_fork+0x28/0x2c [71556.835569] INFO: lockdep is turned off. [71556.835573] FIX kmalloc-128: Restoring 0x00000000d20894be-0x00000000aaef63e9=0x6b [71556.835577] FIX kmalloc-128: Marking all objects used Fixes: fd7f3a746582 ("net/smc: remove freed buffer from list") Reviewed-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-03net/smc: set rx_off for SMCR explicitlyUrsula Braun
SMC tries to make use of SMCD first. If a problem shows up, it tries to switch to SMCR. If the SMCD initializing problem shows up after the SMCD connection has already been initialized, field rx_off keeps the wrong SMCD value for SMCR, which results in corrupted data at the receiver. This patch adds an explicit (re-)setting of field rx_off to zero if the connection uses SMCR. Fixes: be244f28d22f ("net/smc: add SMC-D support in data transfer") Reviewed-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-03net/smc: fix toleration of fake add_link messagesKarsten Graul
Older SMCR implementations had no link failover support and used one link only. Because the handshake protocol requires to try the establishment of a second link the old code sent a fake add_link message and declined any server response afterwards. The current code supports multiple links and inspects the received fake add_link message more closely. To tolerate the fake add_link messages smc_llc_is_local_add_link() needs an improved check of the message to be able to separate between locally enqueued and fake add_link messages. And smc_llc_cli_add_link() needs to check if the provided qp_mtu size is invalid and reject the add_link request in that case. Fixes: c48254fa48e5 ("net/smc: move add link processing for new device into llc layer") Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-02tipc: fix shutdown() of connectionless socketTetsuo Handa
syzbot is reporting hung task at nbd_ioctl() [1], for there are two problems regarding TIPC's connectionless socket's shutdown() operation. ---------- #include <fcntl.h> #include <sys/socket.h> #include <sys/ioctl.h> #include <linux/nbd.h> #include <unistd.h> int main(int argc, char *argv[]) { const int fd = open("/dev/nbd0", 3); alarm(5); ioctl(fd, NBD_SET_SOCK, socket(PF_TIPC, SOCK_DGRAM, 0)); ioctl(fd, NBD_DO_IT, 0); /* To be interrupted by SIGALRM. */ return 0; } ---------- One problem is that wait_for_completion() from flush_workqueue() from nbd_start_device_ioctl() from nbd_ioctl() cannot be completed when nbd_start_device_ioctl() received a signal at wait_event_interruptible(), for tipc_shutdown() from kernel_sock_shutdown(SHUT_RDWR) from nbd_mark_nsock_dead() from sock_shutdown() from nbd_start_device_ioctl() is failing to wake up a WQ thread sleeping at wait_woken() from tipc_wait_for_rcvmsg() from sock_recvmsg() from sock_xmit() from nbd_read_stat() from recv_work() scheduled by nbd_start_device() from nbd_start_device_ioctl(). Fix this problem by always invoking sk->sk_state_change() (like inet_shutdown() does) when tipc_shutdown() is called. The other problem is that tipc_wait_for_rcvmsg() cannot return when tipc_shutdown() is called, for tipc_shutdown() sets sk->sk_shutdown to SEND_SHUTDOWN (despite "how" is SHUT_RDWR) while tipc_wait_for_rcvmsg() needs sk->sk_shutdown set to RCV_SHUTDOWN or SHUTDOWN_MASK. Fix this problem by setting sk->sk_shutdown to SHUTDOWN_MASK (like inet_shutdown() does) when the socket is connectionless. [1] https://syzkaller.appspot.com/bug?id=3fe51d307c1f0a845485cf1798aa059d12bf18b2 Reported-by: syzbot <syzbot+e36f41d207137b5d12f7@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-02ipv6: Fix sysctl max for fib_multipath_hash_policyIdo Schimmel
Cited commit added the possible value of '2', but it cannot be set. Fix it by adjusting the maximum value to '2'. This is consistent with the corresponding IPv4 sysctl. Before: # sysctl -w net.ipv6.fib_multipath_hash_policy=2 sysctl: setting key "net.ipv6.fib_multipath_hash_policy": Invalid argument net.ipv6.fib_multipath_hash_policy = 2 # sysctl net.ipv6.fib_multipath_hash_policy net.ipv6.fib_multipath_hash_policy = 0 After: # sysctl -w net.ipv6.fib_multipath_hash_policy=2 net.ipv6.fib_multipath_hash_policy = 2 # sysctl net.ipv6.fib_multipath_hash_policy net.ipv6.fib_multipath_hash_policy = 2 Fixes: d8f74f0975d8 ("ipv6: Support multipath hashing on inner IP pkts") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Stephen Suryaputra <ssuryaextr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-01pktgen: fix error message with wrong function nameLeesoo Ahn
Error on calling kthread_create_on_node prints wrong function name, kernel_thread. Fixes: 94dcf29a11b3 ("kthread: use kthread_create_on_node()") Signed-off-by: Leesoo Ahn <dev@ooseel.net> Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Do not delete clash entries on reply, let them expire instead, from Florian Westphal. 2) Do not report EAGAIN to nfnetlink, otherwise this enters a busy loop. Update nfnetlink_unicast() to translate EAGAIN to ENOBUFS. 3) Remove repeated words in code comments, from Randy Dunlap. 4) Several patches for the flowtable selftests, from Fabian Frederick. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-30tipc: fix using smp_processor_id() in preemptibleTuong Lien
The 'this_cpu_ptr()' is used to obtain the AEAD key' TFM on the current CPU for encryption, however the execution can be preemptible since it's actually user-space context, so the 'using smp_processor_id() in preemptible' has been observed. We fix the issue by using the 'get/put_cpu_ptr()' API which consists of a 'preempt_disable()' instead. Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication") Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-29netfilter: conntrack: do not auto-delete clash entries on replyFlorian Westphal
Its possible that we have more than one packet with the same ct tuple simultaneously, e.g. when an application emits n packets on same UDP socket from multiple threads. NAT rules might be applied to those packets. With the right set of rules, n packets will be mapped to m destinations, where at least two packets end up with the same destination. When this happens, the existing clash resolution may merge the skb that is processed after the first has been received with the identical tuple already in hash table. However, its possible that this identical tuple is a NAT_CLASH tuple. In that case the second skb will be sent, but no reply can be received since the reply that is processed first removes the NAT_CLASH tuple. Do not auto-delete, this gives a 1 second window for replies to be passed back to originator. Packets that are coming later (udp stream case) will not be affected: they match the original ct entry, not a NAT_CLASH one. Also prevent NAT_CLASH entries from getting offloaded. Fixes: 6a757c07e51f ("netfilter: conntrack: allow insertion of clashing entries") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-28netfilter: nfnetlink: nfnetlink_unicast() reports EAGAIN instead of ENOBUFSPablo Neira Ayuso
Frontend callback reports EAGAIN to nfnetlink to retry a command, this is used to signal that module autoloading is required. Unfortunately, nlmsg_unicast() reports EAGAIN in case the receiver socket buffer gets full, so it enters a busy-loop. This patch updates nfnetlink_unicast() to turn EAGAIN into ENOBUFS and to use nlmsg_unicast(). Remove the flags field in nfnetlink_unicast() since this is always MSG_DONTWAIT in the existing code which is exactly what nlmsg_unicast() passes to netlink_unicast() as parameter. Fixes: 96518518cc41 ("netfilter: add nftables") Reported-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-28netfilter: delete repeated wordsRandy Dunlap
Drop duplicated words in net/netfilter/ and net/ipv4/netfilter/. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-28net_sched: fix error path in red_init()Cong Wang
When ->init() fails, ->destroy() is called to clean up. So it is unnecessary to clean up in red_init(), and it would cause some refcount underflow. Fixes: aee9caa03fc3 ("net: sched: sch_red: Add qevents "early_drop" and "mark"") Reported-and-tested-by: syzbot+b33c1cb0a30ebdc8a5f9@syzkaller.appspotmail.com Reported-and-tested-by: syzbot+e5ea5f8a3ecfd4427a1c@syzkaller.appspotmail.com Cc: Petr Machata <petrm@mellanox.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-28netlink: fix a data race in netlink_rcv_wake()zhudi
The data races were reported by KCSAN: BUG: KCSAN: data-race in netlink_recvmsg / skb_queue_tail write (marked) to 0xffff8c0986e5a8c8 of 8 bytes by interrupt on cpu 3: skb_queue_tail+0xcc/0x120 __netlink_sendskb+0x55/0x80 netlink_broadcast_filtered+0x465/0x7e0 nlmsg_notify+0x8f/0x120 rtnl_notify+0x8e/0xb0 __neigh_notify+0xf2/0x120 neigh_update+0x927/0xde0 arp_process+0x8a3/0xf50 arp_rcv+0x27c/0x3b0 __netif_receive_skb_core+0x181c/0x1840 __netif_receive_skb+0x38/0xf0 netif_receive_skb_internal+0x77/0x1c0 napi_gro_receive+0x1bd/0x1f0 e1000_clean_rx_irq+0x538/0xb20 [e1000] e1000_clean+0x5e4/0x1340 [e1000] net_rx_action+0x310/0x9d0 __do_softirq+0xe8/0x308 irq_exit+0x109/0x110 do_IRQ+0x7f/0xe0 ret_from_intr+0x0/0x1d 0xffffffffffffffff read to 0xffff8c0986e5a8c8 of 8 bytes by task 1463 on cpu 0: netlink_recvmsg+0x40b/0x820 sock_recvmsg+0xc9/0xd0 ___sys_recvmsg+0x1a4/0x3b0 __sys_recvmsg+0x86/0x120 __x64_sys_recvmsg+0x52/0x70 do_syscall_64+0xb5/0x360 entry_SYSCALL_64_after_hwframe+0x65/0xca 0xffffffffffffffff Since the write is under sk_receive_queue->lock but the read is done as lockless. so fix it by using skb_queue_empty_lockless() instead of skb_queue_empty() for the read in netlink_rcv_wake() Signed-off-by: zhudi <zhudi21@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-28Merge tag 'mac80211-for-davem-2020-08-28' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== We have: * fixes for AQL (airtime queue limits) * reduce packet loss detection false positives * a small channel number fix for the 6 GHz band * a fix for 80+80/160 MHz negotiation * an nl80211 attribute (NL80211_ATTR_HE_6GHZ_CAPABILITY) fix * add a missing sanity check for the regulatory code ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-27rxrpc: Fix memory leak in rxkad_verify_response()Dinghao Liu
Fix a memory leak in rxkad_verify_response() whereby the response buffer doesn't get freed if we fail to allocate a ticket buffer. Fixes: ef68622da9cc ("rxrpc: Handle temporary errors better in rxkad security") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-27Merge tag 'rxrpc-fixes-20200820' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs David Howells says: ==================== rxrpc, afs: Fix probing issues Here are some fixes for rxrpc and afs to fix issues in the RTT measuring in rxrpc and thence the Volume Location server probing in afs: (1) Move the serial number of a received ACK into a local variable to simplify the next patch. (2) Fix the loss of RTT samples due to extra interposed ACKs causing baseline information to be discarded too early. This is a particular problem for afs when it sends a single very short call to probe a server it hasn't talked to recently. (3) Fix rxrpc_kernel_get_srtt() to indicate whether it actually has seen any valid samples or not. (4) Remove a field that's set/woken, but never read/waited on. (5) Expose the RTT and other probe information through procfs to make debugging of this stuff easier. (6) Fix VL rotation in afs to only use summary information from VL probing and not the probe running state (which gets clobbered when next a probe is issued). (7) Fix VL rotation to actually return the error aggregated from the probe errors. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-27net: Fix some commentsMiaohe Lin
Fix some comments, including wrong function name, duplicated word and so on. Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-27cfg80211: Adjust 6 GHz frequency to channel conversionAmar Singhal
Adjust the 6 GHz frequency to channel conversion function, the other way around was previously handled. Signed-off-by: Amar Singhal <asinghal@codeaurora.org> Link: https://lore.kernel.org/r/1592599921-10607-1-git-send-email-asinghal@codeaurora.org [rewrite commit message, hard-code channel 2] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-27mac80211: reduce packet loss event false positivesFelix Fietkau
When running a large number of packets per second with a high data rate and long A-MPDUs, the packet loss threshold can be reached very quickly when the link conditions change. This frequently shows up as spurious disconnects. Mitigate false positives by using a similar logic for regular stations as the one being used for TDLS, though with a more aggressive timeout. Packet loss events are only reported if no ACK was received for a second. Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20200808172542.41628-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-27cfg80211: regulatory: reject invalid hintsJohannes Berg
Reject invalid hints early in order to not cause a kernel WARN later if they're restored to or similar. Reported-by: syzbot+d451401ffd00a60677ee@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=d451401ffd00a60677ee Link: https://lore.kernel.org/r/20200819084648.13956-1-johannes@sipsolutions.net Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-27wireless: fix wrong 160/80+80 MHz settingShay Bar
Fix cfg80211_chandef_usable(): consider IEEE80211_VHT_CAP_EXT_NSS_BW when verifying 160/80+80 MHz. Based on: "Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW Support subfield at a STA transmitting the VHT Capabilities Information field" From "Draft P802.11REVmd_D3.0.pdf" Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com> Signed-off-by: Shay Bar <shay.bar@celeno.com> Link: https://lore.kernel.org/r/20200826143139.25976-1-shay.bar@celeno.com [reformat the code a bit and use u32_get_bits()] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-27mac80211: improve AQL aggregation estimation for low data ratesFelix Fietkau
Links with low data rates use much smaller aggregates and are much more sensitive to latency added by bufferbloat. Tune the assumed aggregation length based on the tx rate duration. Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20200821163045.62140-3-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-27mac80211: factor out code to look up the average packet length duration for ↵Felix Fietkau
a rate This will be used to enhance AQL estimated aggregation length Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20200821163045.62140-2-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-27mac80211: use rate provided via status->rate on ieee80211_tx_status_ext for AQLFelix Fietkau
Since ieee80211_tx_info does not have enough room to encode HE rates, HE drivers use status->rate to provide rate info. Store it in struct sta_info and use it for AQL. Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20200821163045.62140-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-26net: disable netpoll on fresh napisJakub Kicinski
napi_disable() makes sure to set the NAPI_STATE_NPSVC bit to prevent netpoll from accessing rings before init is complete. However, the same is not done for fresh napi instances in netif_napi_add(), even though we expect NAPI instances to be added as disabled. This causes crashes during driver reconfiguration (enabling XDP, changing the channel count) - if there is any printk() after netif_napi_add() but before napi_enable(). To ensure memory ordering is correct we need to use RCU accessors. Reported-by: Rob Sherwood <rsher@fb.com> Fixes: 2d8bff12699a ("netpoll: Close race condition between poll_one_napi and napi_disable") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-26ipv4: Silence suspicious RCU usage warningIdo Schimmel
fib_info_notify_update() is always called with RTNL held, but not from an RCU read-side critical section. This leads to the following warning [1] when the FIB table list is traversed with hlist_for_each_entry_rcu(), but without a proper lockdep expression. Since modification of the list is protected by RTNL, silence the warning by adding a lockdep expression which verifies RTNL is held. [1] ============================= WARNING: suspicious RCU usage 5.9.0-rc1-custom-14233-g2f26e122d62f #129 Not tainted ----------------------------- net/ipv4/fib_trie.c:2124 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 1 lock held by ip/834: #0: ffffffff85a3b6b0 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x49a/0xbd0 stack backtrace: CPU: 0 PID: 834 Comm: ip Not tainted 5.9.0-rc1-custom-14233-g2f26e122d62f #129 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014 Call Trace: dump_stack+0x100/0x184 lockdep_rcu_suspicious+0x143/0x14d fib_info_notify_update+0x8d1/0xa60 __nexthop_replace_notify+0xd2/0x290 rtm_new_nexthop+0x35e2/0x5946 rtnetlink_rcv_msg+0x4f7/0xbd0 netlink_rcv_skb+0x17a/0x480 rtnetlink_rcv+0x22/0x30 netlink_unicast+0x5ae/0x890 netlink_sendmsg+0x98a/0xf40 ____sys_sendmsg+0x879/0xa00 ___sys_sendmsg+0x122/0x190 __sys_sendmsg+0x103/0x1d0 __x64_sys_sendmsg+0x7d/0xb0 do_syscall_64+0x32/0x50 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7fde28c3be57 Code: 0c 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10 RSP: 002b:00007ffc09330028 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fde28c3be57 RDX: 0000000000000000 RSI: 00007ffc09330090 RDI: 0000000000000003 RBP: 000000005f45f911 R08: 0000000000000001 R09: 00007ffc0933012c R10: 0000000000000076 R11: 0000000000000246 R12: 0000000000000001 R13: 00007ffc09330290 R14: 00007ffc09330eee R15: 00005610e48ed020 Fixes: 1bff1a0c9bbd ("ipv4: Add function to send route updates") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-26mptcp: free acked data before waiting for more memoryFlorian Westphal
After subflow lock is dropped, more wmem might have been made available. This fixes a deadlock in mptcp_connect.sh 'mmap' mode: wmem is exhausted. But as the mptcp socket holds on to already-acked data (for retransmit) no wakeup will occur. Using 'goto restart' calls mptcp_clean_una(sk) which will free pages that have been acked completely in the mean time. Fixes: fb529e62d3f3 ("mptcp: break and restart in case mptcp sndbuf is full") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-26taprio: Fix using wrong queues in gate maskVinicius Costa Gomes
Since commit 9c66d1564676 ("taprio: Add support for hardware offloading") there's a bit of inconsistency when offloading schedules to the hardware: In software mode, the gate masks are specified in terms of traffic classes, so if say "sched-entry S 03 20000", it means that the traffic classes 0 and 1 are open for 20us; when taprio is offloaded to hardware, the gate masks are specified in terms of hardware queues. The idea here is to fix hardware offloading, so schedules in hardware and software mode have the same behavior. What's needed to do is to map traffic classes to queues when applying the offload to the driver. Fixes: 9c66d1564676 ("taprio: Add support for hardware offloading") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-25Merge tag 'nfsd-5.9-1' of git://git.linux-nfs.org/projects/cel/cel-2.6Linus Torvalds
Pull nfs server fixes from Chuck Lever: - Eliminate an oops introduced in v5.8 - Remove a duplicate #include added by nfsd-5.9 * tag 'nfsd-5.9-1' of git://git.linux-nfs.org/projects/cel/cel-2.6: SUNRPC: remove duplicate include nfsd: fix oops on mixed NFSv4/NFSv3 client access
2020-08-25net: caif: fix error code handlingTong Zhang
cfpkt_peek_head return 0 and 1, caller is checking error using <0 Signed-off-by: Tong Zhang <ztong0001@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-24Merge tag 'batadv-net-for-davem-20200824' of git://git.open-mesh.org/linux-mergeDavid S. Miller
Simon Wunderlich says: ==================== Here are some batman-adv bugfixes: - Avoid uninitialized memory access when handling DHCP, by Sven Eckelmann - Fix check for own OGM in OGM receive handler, by Linus Luessing - Fix netif_rx access for non-interrupt context in BLA, by Jussi Kivilinna ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-24net: Get rid of consume_skb when tracing is offHerbert Xu
The function consume_skb is only meaningful when tracing is enabled. This patch makes it conditional on CONFIG_TRACEPOINTS. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-24netlabel: fix problems with mapping removalPaul Moore
This patch fixes two main problems seen when removing NetLabel mappings: memory leaks and potentially extra audit noise. The memory leaks are caused by not properly free'ing the mapping's address selector struct when free'ing the entire entry as well as not properly cleaning up a temporary mapping entry when adding new address selectors to an existing entry. This patch fixes both these problems such that kmemleak reports no NetLabel associated leaks after running the SELinux test suite. The potentially extra audit noise was caused by the auditing code in netlbl_domhsh_remove_entry() being called regardless of the entry's validity. If another thread had already marked the entry as invalid, but not removed/free'd it from the list of mappings, then it was possible that an additional mapping removal audit record would be generated. This patch fixes this by returning early from the removal function when the entry was previously marked invalid. This change also had the side benefit of improving the code by decreasing the indentation level of large chunk of code by one (accounting for most of the diffstat). Fixes: 63c416887437 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping") Reported-by: Stephen Smalley <stephen.smalley.work@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-24sctp: not disable bh in the whole sctp_get_port_local()Xin Long
With disabling bh in the whole sctp_get_port_local(), when snum == 0 and too many ports have been used, the do-while loop will take the cpu for a long time and cause cpu stuck: [ ] watchdog: BUG: soft lockup - CPU#11 stuck for 22s! [ ] RIP: 0010:native_queued_spin_lock_slowpath+0x4de/0x940 [ ] Call Trace: [ ] _raw_spin_lock+0xc1/0xd0 [ ] sctp_get_port_local+0x527/0x650 [sctp] [ ] sctp_do_bind+0x208/0x5e0 [sctp] [ ] sctp_autobind+0x165/0x1e0 [sctp] [ ] sctp_connect_new_asoc+0x355/0x480 [sctp] [ ] __sctp_connect+0x360/0xb10 [sctp] There's no need to disable bh in the whole function of sctp_get_port_local. So fix this cpu stuck by removing local_bh_disable() called at the beginning, and using spin_lock_bh() instead. The same thing was actually done for inet_csk_get_port() in Commit ea8add2b1903 ("tcp/dccp: better use of ephemeral ports in bind()"). Thanks to Marcelo for pointing the buggy code out. v1->v2: - use cond_resched() to yield cpu to other tasks if needed, as Eric noticed. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Don't flag SCTP heartbeat as invalid for re-used connections, from Florian Westphal. 2) Bogus overlap report due to rbtree tree rotations, from Stefano Brivio. 3) Detect partial overlap with start end point match, also from Stefano. 4) Skip netlink dump of NFTA_SET_USERDATA is unset. 5) Incorrect nft_list_attributes enumeration definition. 6) Missing zeroing before memcpy to destination register, also from Florian. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-22net: nexthop: don't allow empty NHA_GROUPNikolay Aleksandrov
Currently the nexthop code will use an empty NHA_GROUP attribute, but it requires at least 1 entry in order to function properly. Otherwise we end up derefencing null or random pointers all over the place due to not having any nh_grp_entry members allocated, nexthop code relies on having at least the first member present. Empty NHA_GROUP doesn't make any sense so just disallow it. Also add a WARN_ON for any future users of nexthop_create_group(). BUG: kernel NULL pointer dereference, address: 0000000000000080 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] SMP CPU: 0 PID: 558 Comm: ip Not tainted 5.9.0-rc1+ #93 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014 RIP: 0010:fib_check_nexthop+0x4a/0xaa Code: 0f 84 83 00 00 00 48 c7 02 80 03 f7 81 c3 40 80 fe fe 75 12 b8 ea ff ff ff 48 85 d2 74 6b 48 c7 02 40 03 f7 81 c3 48 8b 40 10 <48> 8b 80 80 00 00 00 eb 36 80 78 1a 00 74 12 b8 ea ff ff ff 48 85 RSP: 0018:ffff88807983ba00 EFLAGS: 00010213 RAX: 0000000000000000 RBX: ffff88807983bc00 RCX: 0000000000000000 RDX: ffff88807983bc00 RSI: 0000000000000000 RDI: ffff88807bdd0a80 RBP: ffff88807983baf8 R08: 0000000000000dc0 R09: 000000000000040a R10: 0000000000000000 R11: ffff88807bdd0ae8 R12: 0000000000000000 R13: 0000000000000000 R14: ffff88807bea3100 R15: 0000000000000001 FS: 00007f10db393700(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000080 CR3: 000000007bd0f004 CR4: 00000000003706f0 Call Trace: fib_create_info+0x64d/0xaf7 fib_table_insert+0xf6/0x581 ? __vma_adjust+0x3b6/0x4d4 inet_rtm_newroute+0x56/0x70 rtnetlink_rcv_msg+0x1e3/0x20d ? rtnl_calcit.isra.0+0xb8/0xb8 netlink_rcv_skb+0x5b/0xac netlink_unicast+0xfa/0x17b netlink_sendmsg+0x334/0x353 sock_sendmsg_nosec+0xf/0x3f ____sys_sendmsg+0x1a0/0x1fc ? copy_msghdr_from_user+0x4c/0x61 ___sys_sendmsg+0x63/0x84 ? handle_mm_fault+0xa39/0x11b5 ? sockfd_lookup_light+0x72/0x9a __sys_sendmsg+0x50/0x6e do_syscall_64+0x54/0xbe entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f10dacc0bb7 Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb cd 66 0f 1f 44 00 00 8b 05 9a 4b 2b 00 85 c0 75 2e 48 63 ff 48 63 d2 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 01 c3 48 8b 15 b1 f2 2a 00 f7 d8 64 89 02 48 RSP: 002b:00007ffcbe628bf8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007ffcbe628f80 RCX: 00007f10dacc0bb7 RDX: 0000000000000000 RSI: 00007ffcbe628c60 RDI: 0000000000000003 RBP: 000000005f41099c R08: 0000000000000001 R09: 0000000000000008 R10: 00000000000005e9 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 00007ffcbe628d70 R15: 0000563a86c6e440 Modules linked in: CR2: 0000000000000080 CC: David Ahern <dsahern@gmail.com> Fixes: 430a049190de ("nexthop: Add support for nexthop groups") Reported-by: syzbot+a61aa19b0c14c8770bd9@syzkaller.appspotmail.com Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-21Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller
Alexei Starovoitov says: ==================== pull-request: bpf 2020-08-21 The following pull-request contains BPF updates for your *net* tree. We've added 11 non-merge commits during the last 5 day(s) which contain a total of 12 files changed, 78 insertions(+), 24 deletions(-). The main changes are: 1) three fixes in BPF task iterator logic, from Yonghong. 2) fix for compressed dwarf sections in vmlinux, from Jiri. 3) fix xdp attach regression, from Andrii. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-21netfilter: nf_tables: fix destination register zeroingFlorian Westphal
Following bug was reported via irc: nft list ruleset set knock_candidates_ipv4 { type ipv4_addr . inet_service size 65535 elements = { 127.0.0.1 . 123, 127.0.0.1 . 123 } } .. udp dport 123 add @knock_candidates_ipv4 { ip saddr . 123 } udp dport 123 add @knock_candidates_ipv4 { ip saddr . udp dport } It should not have been possible to add a duplicate set entry. After some debugging it turned out that the problem is the immediate value (123) in the second-to-last rule. Concatenations use 32bit registers, i.e. the elements are 8 bytes each, not 6 and it turns out the kernel inserted inet firewall @knock_candidates_ipv4 element 0100007f ffff7b00 : 0 [end] element 0100007f 00007b00 : 0 [end] Note the non-zero upper bits of the first element. It turns out that nft_immediate doesn't zero the destination register, but this is needed when the length isn't a multiple of 4. Furthermore, the zeroing in nft_payload is broken. We can't use [len / 4] = 0 -- if len is a multiple of 4, index is off by one. Skip zeroing in this case and use a conditional instead of (len -1) / 4. Fixes: 49499c3e6e18 ("netfilter: nf_tables: switch registers to 32 bit addressing") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-21netfilter: nf_tables: add NFTA_SET_USERDATA if not nullPablo Neira Ayuso
Kernel sends an empty NFTA_SET_USERDATA attribute with no value if userspace adds a set with no NFTA_SET_USERDATA attribute. Fixes: e6d8ecac9e68 ("netfilter: nf_tables: Add new attributes into nft_set to store user data.") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-21netfilter: nft_set_rbtree: Detect partial overlap with start endpoint matchStefano Brivio
Getting creative with nft and omitting the interval_overlap() check from the set_overlap() function, without omitting set_overlap() altogether, led to the observation of a partial overlap that wasn't detected, and would actually result in replacement of the end element of an existing interval. This is due to the fact that we'll return -EEXIST on a matching, pre-existing start element, instead of -ENOTEMPTY, and the error is cleared by API if NLM_F_EXCL is not given. At this point, we can insert a matching start, and duplicate the end element as long as we don't end up into other intervals. For instance, inserting interval 0 - 2 with an existing 0 - 3 interval would result in a single 0 - 2 interval, and a dangling '3' end element. This is because nft will proceed after inserting the '0' start element as no error is reported, and no further conflicting intervals are detected on insertion of the end element. This needs a different approach as it's a local condition that can be detected by looking for duplicate ends coming from left and right, separately. Track those and directly report -ENOTEMPTY on duplicated end elements for a matching start. Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-21netfilter: nft_set_rbtree: Handle outcomes of tree rotations in overlap ↵Stefano Brivio
detection Checks for partial overlaps on insertion assume that end elements are always descendant nodes of their corresponding start, because they are inserted later. However, this is not the case if a previous delete operation caused a tree rotation as part of rebalancing. Taking the issue reported by Andreas Fischer as an example, if we omit delete operations, the existing procedure works because, equivalently, we are inserting a start item with value 40 in the this region of the red-black tree with single-sized intervals: overlap flag 10 (start) / \ false 20 (start) / \ false 30 (start) / \ false 60 (start) / \ false 50 (end) / \ false 20 (end) / \ false 40 (start) if we now delete interval 30 - 30, the tree can be rearranged in a way similar to this (note the rotation involving 50 - 50): overlap flag 10 (start) / \ false 20 (start) / \ false 25 (start) / \ false 70 (start) / \ false 50 (end) / \ true (from rule a1.) 50 (start) / \ true 40 (start) and we traverse interval 50 - 50 from the opposite direction compared to what was expected. To deal with those cases, add a start-before-start rule, b4., that covers traversal of existing intervals from the right. We now need to restrict start-after-end rule b3. to cases where there are no occurring nodes between existing start and end elements, because addition of rule b4. isn't sufficient to ensure that the pre-existing end element we encounter while descending the tree corresponds to a start element of an interval that we already traversed entirely. Different types of overlap detection on trees with rotations resulting from re-balancing will be covered by nft test case sets/0044interval_overlap_1. Reported-by: Andreas Fischer <netfilter@d9c.eu> Bugzilla: https://bugzilla.netfilter.org/show_bug.cgi?id=1449 Cc: <stable@vger.kernel.org> # 5.6.x Fixes: 7c84d41416d8 ("netfilter: nft_set_rbtree: Detect partial overlaps on insertion") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-20tipc: call rcu_read_lock() in tipc_aead_encrypt_done()Xin Long
b->media->send_msg() requires rcu_read_lock(), as we can see elsewhere in tipc, tipc_bearer_xmit, tipc_bearer_xmit_skb and tipc_bearer_bc_xmit(). Syzbot has reported this issue as: net/tipc/bearer.c:466 suspicious rcu_dereference_check() usage! Workqueue: cryptd cryptd_queue_worker Call Trace: tipc_l2_send_msg+0x354/0x420 net/tipc/bearer.c:466 tipc_aead_encrypt_done+0x204/0x3a0 net/tipc/crypto.c:761 cryptd_aead_crypt+0xe8/0x1d0 crypto/cryptd.c:739 cryptd_queue_worker+0x118/0x1b0 crypto/cryptd.c:181 process_one_work+0x94c/0x1670 kernel/workqueue.c:2269 worker_thread+0x64c/0x1120 kernel/workqueue.c:2415 kthread+0x3b5/0x4a0 kernel/kthread.c:291 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293 So fix it by calling rcu_read_lock() in tipc_aead_encrypt_done() for b->media->send_msg(). Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication") Reported-by: syzbot+47bbc6b678d317cccbe0@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-20net/sched: act_ct: Fix skb double-free in tcf_ct_handle_fragments() error flowAlaa Hleihel
tcf_ct_handle_fragments() shouldn't free the skb when ip_defrag() call fails. Otherwise, we will cause a double-free bug. In such cases, just return the error to the caller. Fixes: b57dc7c13ea9 ("net/sched: Introduce action ct") Signed-off-by: Alaa Hleihel <alaa@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-20net: sctp: Fix negotiation of the number of data streams.David Laight
The number of output and input streams was never being reduced, eg when processing received INIT or INIT_ACK chunks. The effect is that DATA chunks can be sent with invalid stream ids and then discarded by the remote system. Fixes: 2075e50caf5ea ("sctp: convert to genradix") Signed-off-by: David Laight <david.laight@aculab.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-20gre6: Fix reception with IP6_TNL_F_RCV_DSCP_COPYMark Tomlinson
When receiving an IPv4 packet inside an IPv6 GRE packet, and the IP6_TNL_F_RCV_DSCP_COPY flag is set on the tunnel, the IPv4 header would get corrupted. This is due to the common ip6_tnl_rcv() function assuming that the inner header is always IPv6. This patch checks the tunnel protocol for IPv4 inner packets, but still defaults to IPv6. Fixes: 308edfdf1563 ("gre6: Cleanup GREv6 receive path, call common GRE functions") Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-20bpf: xdp: Fix XDP mode when no mode flags specifiedAndrii Nakryiko
7f0a838254bd ("bpf, xdp: Maintain info on attached XDP BPF programs in net_device") inadvertently changed which XDP mode is assumed when no mode flags are specified explicitly. Previously, driver mode was preferred, if driver supported it. If not, generic SKB mode was chosen. That commit changed default to SKB mode always. This patch fixes the issue and restores the original logic. Fixes: 7f0a838254bd ("bpf, xdp: Maintain info on attached XDP BPF programs in net_device") Reported-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Tested-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/bpf/20200820052841.1559757-1-andriin@fb.com