aboutsummaryrefslogtreecommitdiff
path: root/drivers/dma/amba-pl08x.c
AgeCommit message (Collapse)Author
2012-05-11dmaengine: Use dma_sg_len(sg) instead of sg->lengthLars-Peter Clausen
sg->length may or may not contain the length of the dma region to transfer, depending on the architecture - dma_sg_len(sg) always will though. For the architectures which use the drivers modified by this patch it probably is the case that sg->length contains the dma transfer length. But to be consistent and future proof change them to use dma_sg_len. To quote Russel King: sg->length is meaningless to something performing DMA. In cases where sg_dma_len(sg) and sg->length are the same storage, then there's no problem. But scatterlists _can_ (and one some architectures) do split them - especially when you have an IOMMU which can allow you to combine a scatterlist into fewer entries. So, anything using sg->length for the size of a scatterlist's DMA transfer _after_ a call to dma_map_sg() is almost certainly buggy. The patch has been generated using the following coccinelle patch: <smpl> @@ struct scatterlist *sg; expression X; @@ -sg[X].length +sg_dma_len(&sg[X]) @@ struct scatterlist *sg; @@ -sg->length +sg_dma_len(sg) </smpl> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-05-11dmaengine: Use sg_dma_address instead of sg_physLars-Peter Clausen
dmaengine drivers should always use sg_dma_address instead of sg_phys to get the addresses for the transfer from a sg element. To quote Russel King: sg_phys(sg) of course has nothing to do with DMA addresses. It's the physical address _to the CPU_ of the memory associated with the scatterlist entry. That may, or may not have the same value for the DMA engine, particularly if IOMMUs are involved. And if these drivers are used on ARM, they must be fixed, sooner rather than later. There's patches in the works which will mean we will end up with IOMMU support in the DMA mapping later, which means everything I've said above will become reality. The patch has been generated using the following coccinelle patch: <smpl> @@ struct scatterlist *sg; @@ -sg_phys(sg) +sg_dma_address(sg) </smpl> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-25Merge branch 'fixes' into nextVinod Koul
2012-04-25dma/amba-pl08x: add support for the Nomadik variantLinus Walleij
The Nomadik PL080 variant has some extra protection bits that may be set, so we need to check these bits to see if the channels are actually available for the DMAengine to use. Cc: Russell King <linux@arm.linux.org.uk> Cc: Alim Akhtar <alim.akhtar@gmail.com> Cc: Alessandro Rubini <rubini@gnudd.com> Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-25dmaengine/amba-pl08x : reset phychan_hold on terminate allDavide Ciminaghi
When a client calls pl08x_control with DMA_TERMINATE_ALL, it is correct to terminate and release the phy channel currently in use (if one is in use), but the phychan_hold counter must also be reset (otherwise it could get trapped in an unbalanced state). Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com> Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-23dma/amba-pl08x: check for terminal count status onlyLinus Walleij
For some reason I can't figure out we're reading the PL080_INT_STATUS register instead of PL080_TC_STATUS when checking for the terminal count. The PL080_INT_STATUS is a logical OR between the error and terminal count status register and may not report what we want it to, especially if there is an error and a terminal count at the same time and the former is not lowered in time for the check in the TC register. Make sure we read what we're actually interested in. Cc: Russell King <linux@arm.linux.org.uk> Cc: Viresh Kumar <viresh.kumar@st.com> Cc: Alim Akhtar <alim.akhtar@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-21dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclicAlexandre Bounine
Add context parameter to device_prep_slave_sg() and device_prep_dma_cyclic() interfaces to allow passing client/target specific information associated with the data transfer. Modify all affected DMA engine drivers. Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-13dmaengine: consolidate initialization of cookiesRussell King - ARM Linux
Provide a common function to initialize a channels cookie values. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jassi Brar <jassisinghbrar@gmail.com> [imx-sdma.c & mxs-dma.c] Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-13dmaengine: consolidate tx_status functionsRussell King - ARM Linux
Now that we have the completed cookie in the dma_chan structure, we can consolidate the tx_status functions by providing a function to set the txstate structure and returning the DMA status. We also provide a separate helper to set the residue for cookies which are still in progress. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jassi Brar <jassisinghbrar@gmail.com> [imx-sdma.c & mxs-dma.c] Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-13dmaengine: provide a common function for completing a dma descriptorRussell King - ARM Linux
Provide a common function to do the cookie mechanics for completing a DMA descriptor. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jassi Brar <jassisinghbrar@gmail.com> [imx-sdma.c & mxs-dma.c] Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-13dmaengine: consolidate assignment of DMA cookiesRussell King - ARM Linux
Everyone deals with assigning DMA cookies in the same way (it's part of the API so they should be), so lets consolidate the common code into a helper function to avoid this duplication. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jassi Brar <jassisinghbrar@gmail.com> [imx-sdma.c & mxs-dma.c] Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-13dmaengine: add private header fileRussell King - ARM Linux
Add a local private header file to contain definitions and declarations which should only be used by DMA engine drivers. We also fix linux/dmaengine.h to use LINUX_DMAENGINE_H to guard against multiple inclusion. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jassi Brar <jassisinghbrar@gmail.com> [imx-sdma.c & mxs-dma.c] Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-13dmaengine: move last completed cookie into generic dma_chan structureRussell King - ARM Linux
Every DMA engine implementation declares a last completed dma cookie in their private dma channel structures. This is pointless, and forces driver specific code. Move this out into the common dma_chan structure. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jassi Brar <jassisinghbrar@gmail.com> [imx-sdma.c & mxs-dma.c] Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-02-22dmaengine/amba-pl08x: Take flow controller info from DMA_SLAVE_CONFIGViresh Kumar
Flow controller information is passed now from DMA_SLAVE_CONFIG option. This patch makes changes in pl08x driver to use device_fc from it instead of platform data. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-01-31drivers/dma/amba-pl08x.c: adjust double testJulia Lawall
Rewrite a duplicated test to test the correct value The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression E; @@ ( * E || ... || E | * E && ... && E ) // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-01-17Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits) ARM: mach-shmobile: specify CHCLR registers on SH7372 dma: shdma: fix runtime PM: clear channel buffers on reset dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit dmaengine/ste_dma40: clear LNK on channel startup dmaengine: intel_mid_dma: remove legacy pm interface ASoC: mxs: correct 'direction' of device_prep_dma_cyclic dmaengine: intel_mid_dma: error path fix dmaengine: intel_mid_dma: locking and freeing fixes mtd: gpmi-nand: move to dma_transfer_direction mtd: fix compile error for gpmi-nand mmc: mxs-mmc: fix the dma_transfer_direction migration dmaengine: add DMA_TRANS_NONE to dma_transfer_direction dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled. dma: mxs-dma: fix a typo in comment DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove video i.MX IPU: Fix display connections i.MX IPU DMA: Fix wrong burstsize settings dmaengine/ste_dma40: allow fixed physical channel ... Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c} The conflicts looked pretty trivial, but I'll ask people to verify them.
2011-12-05dmaengine/amba-pl08x: Config ccfg and increment phychan_hold if phychan is trueViresh Kumar
Currently, if plchan->phychan is true, we return immediately from prep_phy_chan(). We must configure txd->ccfg and increment phychan_hold before returning. Otherwise, request line number wouldn't be configured in this txd. Reported-by: Rajeev Kumar <rajeev-dlh.kumar@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2011-11-22dmaengine: pl08x: Enable module alias autogeneration for AMBA driversDave Martin
Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Vinod Koul <vinod.koul@intel.com>
2011-10-27dmaengine: move drivers to dma_transfer_directionVinod Koul
fixup usage of dma direction by introducing dma_transfer_direction, this patch moves dma/drivers/* to use new enum Cc: Jassi Brar <jaswinder.singh@linaro.org> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Viresh Kumar <viresh.kumar@st.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Mika Westerberg <mika.westerberg@iki.fi> Cc: H Hartley Sweeten <hartleys@visionengravers.com> Cc: Li Yang <leoli@freescale.com> Cc: Zhang Wei <zw@zh-kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Cc: Shawn Guo <shawn.guo@freescale.com> Cc: Yong Wang <yong.y.wang@intel.com> Cc: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Cc: Boojin Kim <boojin.kim@samsung.com> Cc: Barry Song <Baohua.Song@csr.com> Acked-by: Mika Westerberg <mika.westerberg@iki.fi> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2011-09-19dmaengine/amba-pl08x: Check txd->llis_va before freeing dma_poolViresh Kumar
In pl08x_free_txd(), check if pool is allocated successfully before freeing it. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-09-19dmaengine/amba-pl08x: Add support for sg len greater than one for slave ↵Viresh Kumar
transfers Untill now, sg_len greater than one is not supported. This patch adds support to do that. Note: Still, if peripheral is flow controller, sg_len can't be greater that one. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-09-05dmaengine: amba-pl08x: make filter check that the channel is owned by pl08xRussell King - ARM Linux
Before converting the dma channel to our private data structure, first check that the channel is indeed one which our driver registered. We do this by ensuring that the underlying device is bound to our driver. This avoids potential oopses if we try to reference 'plchan->name' against a foreign drivers dma channel. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-09-02Merge branch 'next' into v3.1-rc4Vinod Koul
Fixed trivial conflicts in drivers/dma/amba-pl08x.c Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Call pl08x_free_txd() instead of calling kfree() directlyViresh Kumar
pl08x_prep_channel_resources() is calling kfree() directly for txd(). To maintain consistency in code call pl08x_free_txd() instead. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Pass flow controller information with slave channel dataViresh Kumar
At least, on SPEAr platforms there is one peripheral, JPEG, which can be flow controller for DMA transfer. Currently DMA controller driver didn't support peripheral flow controller configurations. This patch adds device_fc field in struct pl08x_channel_data, which will be used only for slave transfers and is not used in case of mem2mem transfers. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Choose peripheral bus as master busViresh Kumar
When we have DMA transfers between peripheral and memory, then we shouldn't reduce width of peripheral at all, as that may be a strict requirement. But we can always reduce width of memory access, with some compromise in performance. Thus, we must select peripheral as master and not memory. Also this rearranges code to make it shorter. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Align lli_len to max(src.width, dst.width)Viresh Kumar
Currently lli_len is aligned to min of two widths, which looks to be incorrect. Instead it should be aligned to max of both widths. Lets say, total_size = 441 bytes MIN: lets check if min() suits or not: CASE 1: srcwidth = 1, dstwidth = 4 min(src, dst) = 1 i.e. We program transfer size in control reg to 441. Now, till 440 bytes everything is fine, but on the last byte DMAC can't transfer 1 byte to dst, as its width is 4. CASE 2: srcwidth = 4, dstwidth = 1 min(src, dst) = 1 i.e. we program transfer size in control reg to 110 (data transferred = 110 * srcwidth). So, here too 1 byte is left, but on the source side. MAX: Lets check if max() suits or not: CASE 3: srcwidth = 1, dstwidth = 4 max(src, dst) = 4 Aligned size is 440 i.e. We program transfer size in control reg to 440. Now, all 440 bytes will be transferred without any issues. CASE 4: srcwidth = 4, dstwidth = 1 max(src, dst) = 4 Aligned size is 440 i.e. We program transfer size in control reg to 110 (data transferred = 110 * srcwidth). Now, also all 440 bytes will be transferred without any issues. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Add prep_single_byte_llis() routineViresh Kumar
Code for creating single byte llis is present at several places. Create a routine to avoid code redundancy. Also, we don't need one lli per single byte transfer, we can have single lli to do all single byte transfer. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: max_bytes_per_lli is TRANSFER_SIZE * src_width (not ↵Viresh Kumar
MIN(width)) max_bytes_per_lli = bd.srcbus.buswidth * PL080_CONTROL_TRANSFER_SIZE_MASK; This is confirmed by ARM support guys. Below is summary of mail exchange with them: [Viresh] What is the total data to be transferred in case source and destination bus widths are different. Suppose, source bus width is 2 bytes and destination is 4 bytes. Now in order to transfer 80 bytes, what should be value of TransferSize field in control reg: 40? or 20?. [David from ARM] The value that is programmed into the TransferSize field should be the number of <SourceWidth> transfers needed to achieve the required data transfer. So, to transfer 80 bytes, with a Source Width of 2, the TransferSize field = should be programmed with: Total transfer size ------------------- = 40 <source width> [Viresh] Will this change if source is 4 bytes and dest is 2? [David] Yes - the calculation then becomes: Total transfer size ------------------- =20 <source width> Also, max_bytes_per_lli must be calculated after fixing src and dest widths not before that. So move this code to the correct place. This patch also removes max_bytes_per_lli from earlier print message, as till that point max_bytes_per_lli is unknown. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Get rid of pl08x_pre_boundary()Viresh Kumar
Pl080 Manual says: "Bursts do not cross the 1KB address boundary" We can program the controller to cross 1 KB boundary on a burst and controller can take care of this boundary condition by itself. Following is the discussion with ARM Technical Support Guys (David): [Viresh] Manual says: "Bursts do not cross the 1KB address boundary" What does that actually mean? As, Maximum size transferable with a single LLI is 4095 * 4 =16380 ~ 16KB. So, if we don't have src/dest address aligned to burst size, we can't use this big of an LLI. [David] There is a difference between bursts describing the total data transferred by the DMA controller and AHB bursts. Bursts described by the programmable parameters in the PL080 have no direct connection with the bursts that are seen on the AHB bus. The statement that "Bursts do not cross the 1KB address boundary" in the TRM is referring to AHB bursts, where this limitation is a requirement of the AHB spec. You can still issue bursts within the PL080 that are in excess of 1KB. The PL080 will make sure that its bursts are broken down into legal AHB bursts which will be formatted to ensure that no AHB burst crosses a 1KB boundary. Based on above discussion, this patch removes all code related to 1 KB boundary as we are not required to handle this in driver. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Schedule tasklet in case of error interruptViresh Kumar
Currently, if error interrupt occurs, nothing is done in interrupt handler (just clearing the interrupts). We must somehow indicate this to the user that DMA is over, due to ERR interrupt or TC interrupt. So, this patch just schedules existing tasklet, with a print showing error interrupt has occurred on which channels. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: No need to check "ch->signal < 0"Viresh Kumar
We have just executed following in pl08x_get_phy_channel(): ch->signal = -1; We don't have to compare "ch->signal < 0", as this will always be true. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Simplify pl08x_ensure_on()Viresh Kumar
Simply writing 1 on bit 0 is sufficient instead of reading and clearing bits. Also as per manual, for bit 3-31 of DMACConfiguration register: "read undefined, write as 0" So, we must not rely on values read from this registers bit 3-31. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: support runtime PMViresh Kumar
Insert notifiers for the runtime PM API. With this the runtime PM layer kicks in to action where used. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Changing few prints to dev_dbg from dev_infoViresh Kumar
For 8 memory and 16 slave channels 35 boot print lines are printed. And that is too much. Most of this would be more useful for debugging. So moving few of them to dev_dbg instead of dev_info. Now only 3 prints will be printed. This also rearrange one of the debug message to fit into two lines. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Remove redundant comment and rewrite originalViresh Kumar
Similar comment is present over routine also pl08x_choose_master_bus(). Keeping one of them. Also rewrite that comment to convey message clearly. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: pass (*ptr) to sizeof() instead of (struct xyz)Viresh Kumar
As mentioned in Documentation/CodingStyle, The preferred form for passing a size of a struct is the following: p = kmalloc(sizeof(*p), ...); The alternative form where struct name is spelled out hurts readability and introduces an opportunity for a bug when the pointer variable type is changed but the corresponding sizeof that is passed to a memory allocator is not. This patch replaces (struct xyz) with *ptr at several occurrences in driver. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Rearrange inclusion of header files in ascending orderViresh Kumar
Header files included in driver are not present in alphabetical order. Rearrange them in alphabetical order. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-25dmaengine/amba-pl08x: Resolve formatting issuesViresh Kumar
There were few formatting related issues in code. This patch fixes them. Fixes include: - Remove extra blank lines - align code to 80 cols - combine several lines to one line Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-08-09dmaengine: PL08x: Fix trivial build errorRussell King
Something changed during the 3.1 merge window in the include files which now causes the pl08x DMA engine driver to fail to build. Fix this by adding the now necessary dma-mapping.h include: drivers/dma/amba-pl08x.c: In function ■pl08x_unmap_buffers■: drivers/dma/amba-pl08x.c:1524: error: implicit declaration of function ■dma_unmap_single■ drivers/dma/amba-pl08x.c:1527: error: implicit declaration of function ■dma_unmap_page■ Acked-by: Vinod Koul <vinod.koul@intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-07-26dmaengine: pl08x: handle the rest of enums in pl08x_widthVinod Koul
pl08x_width function does not handle rest of enums for DMA_SLAVE_BUSWIDTH_xxxx which causes gcc to emit below warining drivers/dma/amba-pl08x.c: In function 'pl08x_width': drivers/dma/amba-pl08x.c:1119: warning: enumeration value 'DMA_SLAVE_BUSWIDTH_UNDEFINED' not handled in switch drivers/dma/amba-pl08x.c:1119: warning: enumeration value 'DMA_SLAVE_BUSWIDTH_8_BYTES' not handled in switch this patch adds a default case which returns error Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-07-26DMA: PL08x: cleanup selection of burst sizeRussell King - ARM Linux
Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-07-26DMA: PL08x: avoid recalculating cctl at each prepareRussell King - ARM Linux
Now that we have separate cctl values for M>P and P>M transfers, we can avoid calculating the cctl value each time we prepare a transaction. Move the bus selection and increment setting to the slave configuration and initialization functions. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-07-26DMA: PL08x: cleanup selection of buswidthRussell King - ARM Linux
Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-07-26DMA: PL08x: separately store source/destination cctlRussell King - ARM Linux
Store the source/destination cctl values into the channel structure. This moves us towards being able to avoid a configuration call each time we use the channel. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-07-26DMA: PL08x: separately store source/destination slave addressRussell King - ARM Linux
Store the source/destination slave address separately into the channel structure. This moves us towards being able to avoid a configuration call each time we use the channel. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-07-26DMA: PL08x: clean up LLI debuggingRussell King - ARM Linux
Clean up debugging when setting up the LLI list. This reduces the amount of output while preserving the information, and makes it easier to read. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-07-26DMA: PL08x: select LLI bus only once per LLI setupRussell King - ARM Linux
Avoid re-selecting the LLI bus each time we create an LLI. Move it out of the LLI setup loops. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-07-26DMA: PL08x: remove unused constantsRussell King - ARM Linux
PL08X_WQ_PERIODMIN and PL08X_MAX_ALLOCS are not used, remove them. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2011-02-23ARM: amba: make probe() functions take const id tablesRussell King
Make Primecell driver probe functions take a const pointer to their ID tables. Drivers should never modify their ID tables in their probe handler. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-24 01:41:20 +0000