From f26c07f96829df378e5d6645b598e85c8387cf0e Mon Sep 17 00:00:00 2001 From: Prashant Sreedharan Date: Sat, 20 Dec 2014 12:16:17 -0800 Subject: tg3: tg3_disable_ints using uninitialized mailbox value to disable interrupts [ Upstream commit 05b0aa579397b734f127af58e401a30784a1e315 ] During driver load in tg3_init_one, if the driver detects DMA activity before intializing the chip tg3_halt is called. As part of tg3_halt interrupts are disabled using routine tg3_disable_ints. This routine was using mailbox value which was not initialized (default value is 0). As a result driver was writing 0x00000001 to pci config space register 0, which is the vendor id / device id. This driver bug was exposed because of the commit a7877b17a667 (PCI: Check only the Vendor ID to identify Configuration Request Retry). Also this issue is only seen in older generation chipsets like 5722 because config space write to offset 0 from driver is possible. The newer generation chips ignore writes to offset 0. Also without commit a7877b17a667, for these older chips when a GRC reset is issued the Bootcode would reprogram the vendor id/device id, which is the reason this bug was masked earlier. Fixed by initializing the interrupt mailbox registers before calling tg3_halt. Please queue for -stable. Reported-by: Nils Holland Reported-by: Marcelo Ricardo Leitner Signed-off-by: Prashant Sreedharan Signed-off-by: Michael Chan Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- drivers/net/ethernet/broadcom/tg3.c | 34 +++++++++++++++++----------------- 1 file changed, 17 insertions(+), 17 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index 086eac5af5c2..82061139b215 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -17731,23 +17731,6 @@ static int tg3_init_one(struct pci_dev *pdev, goto err_out_apeunmap; } - /* - * Reset chip in case UNDI or EFI driver did not shutdown - * DMA self test will enable WDMAC and we'll see (spurious) - * pending DMA on the PCI bus at that point. - */ - if ((tr32(HOSTCC_MODE) & HOSTCC_MODE_ENABLE) || - (tr32(WDMAC_MODE) & WDMAC_MODE_ENABLE)) { - tw32(MEMARB_MODE, MEMARB_MODE_ENABLE); - tg3_halt(tp, RESET_KIND_SHUTDOWN, 1); - } - - err = tg3_test_dma(tp); - if (err) { - dev_err(&pdev->dev, "DMA engine test failed, aborting\n"); - goto err_out_apeunmap; - } - intmbx = MAILBOX_INTERRUPT_0 + TG3_64BIT_REG_LOW; rcvmbx = MAILBOX_RCVRET_CON_IDX_0 + TG3_64BIT_REG_LOW; sndmbx = MAILBOX_SNDHOST_PROD_IDX_0 + TG3_64BIT_REG_LOW; @@ -17792,6 +17775,23 @@ static int tg3_init_one(struct pci_dev *pdev, sndmbx += 0xc; } + /* + * Reset chip in case UNDI or EFI driver did not shutdown + * DMA self test will enable WDMAC and we'll see (spurious) + * pending DMA on the PCI bus at that point. + */ + if ((tr32(HOSTCC_MODE) & HOSTCC_MODE_ENABLE) || + (tr32(WDMAC_MODE) & WDMAC_MODE_ENABLE)) { + tw32(MEMARB_MODE, MEMARB_MODE_ENABLE); + tg3_halt(tp, RESET_KIND_SHUTDOWN, 1); + } + + err = tg3_test_dma(tp); + if (err) { + dev_err(&pdev->dev, "DMA engine test failed, aborting\n"); + goto err_out_apeunmap; + } + tg3_init_coal(tp); pci_set_drvdata(pdev, dev); -- cgit v1.2.3 From 07d187d6fd9fe29d88463d83401ed24619a1aeb8 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Sun, 11 Jan 2015 10:32:18 -0800 Subject: alx: fix alx_poll() [ Upstream commit 7a05dc64e2e4c611d89007b125b20c0d2a4d31a5 ] Commit d75b1ade567f ("net: less interrupt masking in NAPI") uncovered wrong alx_poll() behavior. A NAPI poll() handler is supposed to return exactly the budget when/if napi_complete() has not been called. It is also supposed to return number of frames that were received, so that netdev_budget can have a meaning. Also, in case of TX pressure, we still have to dequeue received packets : alx_clean_rx_irq() has to be called even if alx_clean_tx_irq(alx) returns false, otherwise device is half duplex. Signed-off-by: Eric Dumazet Fixes: d75b1ade567f ("net: less interrupt masking in NAPI") Reported-by: Oded Gabbay Bisected-by: Oded Gabbay Tested-by: Oded Gabbay Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- drivers/net/ethernet/atheros/alx/main.c | 24 +++++++++++++----------- 1 file changed, 13 insertions(+), 11 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/atheros/alx/main.c b/drivers/net/ethernet/atheros/alx/main.c index 380d24922049..3e1d7d29b4ec 100644 --- a/drivers/net/ethernet/atheros/alx/main.c +++ b/drivers/net/ethernet/atheros/alx/main.c @@ -184,15 +184,16 @@ static void alx_schedule_reset(struct alx_priv *alx) schedule_work(&alx->reset_wk); } -static bool alx_clean_rx_irq(struct alx_priv *alx, int budget) +static int alx_clean_rx_irq(struct alx_priv *alx, int budget) { struct alx_rx_queue *rxq = &alx->rxq; struct alx_rrd *rrd; struct alx_buffer *rxb; struct sk_buff *skb; u16 length, rfd_cleaned = 0; + int work = 0; - while (budget > 0) { + while (work < budget) { rrd = &rxq->rrd[rxq->rrd_read_idx]; if (!(rrd->word3 & cpu_to_le32(1 << RRD_UPDATED_SHIFT))) break; @@ -203,7 +204,7 @@ static bool alx_clean_rx_irq(struct alx_priv *alx, int budget) ALX_GET_FIELD(le32_to_cpu(rrd->word0), RRD_NOR) != 1) { alx_schedule_reset(alx); - return 0; + return work; } rxb = &rxq->bufs[rxq->read_idx]; @@ -243,7 +244,7 @@ static bool alx_clean_rx_irq(struct alx_priv *alx, int budget) } napi_gro_receive(&alx->napi, skb); - budget--; + work++; next_pkt: if (++rxq->read_idx == alx->rx_ringsz) @@ -258,21 +259,22 @@ next_pkt: if (rfd_cleaned) alx_refill_rx_ring(alx, GFP_ATOMIC); - return budget > 0; + return work; } static int alx_poll(struct napi_struct *napi, int budget) { struct alx_priv *alx = container_of(napi, struct alx_priv, napi); struct alx_hw *hw = &alx->hw; - bool complete = true; unsigned long flags; + bool tx_complete; + int work; - complete = alx_clean_tx_irq(alx) && - alx_clean_rx_irq(alx, budget); + tx_complete = alx_clean_tx_irq(alx); + work = alx_clean_rx_irq(alx, budget); - if (!complete) - return 1; + if (!tx_complete || work == budget) + return budget; napi_complete(&alx->napi); @@ -284,7 +286,7 @@ static int alx_poll(struct napi_struct *napi, int budget) alx_post_write(hw); - return 0; + return work; } static irqreturn_t alx_intr_handle(struct alx_priv *alx, u32 intr) -- cgit v1.2.3 From 0042721e23933b6e56cf2766557addbd6d16a018 Mon Sep 17 00:00:00 2001 From: Govindarajulu Varadarajan <_govind@gmx.com> Date: Thu, 18 Dec 2014 15:58:42 +0530 Subject: enic: fix rx skb checksum [ Upstream commit 17e96834fd35997ca7cdfbf15413bcd5a36ad448 ] Hardware always provides compliment of IP pseudo checksum. Stack expects whole packet checksum without pseudo checksum if CHECKSUM_COMPLETE is set. This causes checksum error in nf & ovs. kernel: qg-19546f09-f2: hw csum failure kernel: CPU: 9 PID: 0 Comm: swapper/9 Tainted: GF O-------------- 3.10.0-123.8.1.el7.x86_64 #1 kernel: Hardware name: Cisco Systems Inc UCSB-B200-M3/UCSB-B200-M3, BIOS B200M3.2.2.3.0.080820141339 08/08/2014 kernel: ffff881218f40000 df68243feb35e3a8 ffff881237a43ab8 ffffffff815e237b kernel: ffff881237a43ad0 ffffffff814cd4ca ffff8829ec71eb00 ffff881237a43af0 kernel: ffffffff814c6232 0000000000000286 ffff8829ec71eb00 ffff881237a43b00 kernel: Call Trace: kernel: [] dump_stack+0x19/0x1b kernel: [] netdev_rx_csum_fault+0x3a/0x40 kernel: [] __skb_checksum_complete_head+0x62/0x70 kernel: [] __skb_checksum_complete+0x11/0x20 kernel: [] nf_ip_checksum+0xcc/0x100 kernel: [] icmp_error+0x1f7/0x35c [nf_conntrack_ipv4] kernel: [] ? netif_rx+0xb9/0x1d0 kernel: [] ? internal_dev_recv+0xdb/0x130 [openvswitch] kernel: [] nf_conntrack_in+0xf0/0xa80 [nf_conntrack] kernel: [] ? inet_del_offload+0x40/0x40 kernel: [] ipv4_conntrack_in+0x22/0x30 [nf_conntrack_ipv4] kernel: [] nf_iterate+0xaa/0xc0 kernel: [] ? inet_del_offload+0x40/0x40 kernel: [] nf_hook_slow+0x84/0x140 kernel: [] ? inet_del_offload+0x40/0x40 kernel: [] ip_rcv+0x344/0x380 Hardware verifies IP & tcp/udp header checksum but does not provide payload checksum, use CHECKSUM_UNNECESSARY. Set it only if its valid IP tcp/udp packet. Cc: Jiri Benc Cc: Stefan Assmann Reported-by: Sunil Choudhary Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Reviewed-by: Jiri Benc Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- drivers/net/ethernet/cisco/enic/enic_main.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/cisco/enic/enic_main.c b/drivers/net/ethernet/cisco/enic/enic_main.c index b740bfce72ef..ff9b423805a0 100644 --- a/drivers/net/ethernet/cisco/enic/enic_main.c +++ b/drivers/net/ethernet/cisco/enic/enic_main.c @@ -1044,10 +1044,14 @@ static void enic_rq_indicate_buf(struct vnic_rq *rq, PKT_HASH_TYPE_L4 : PKT_HASH_TYPE_L3); } - if ((netdev->features & NETIF_F_RXCSUM) && !csum_not_calc) { - skb->csum = htons(checksum); - skb->ip_summed = CHECKSUM_COMPLETE; - } + /* Hardware does not provide whole packet checksum. It only + * provides pseudo checksum. Since hw validates the packet + * checksum but not provide us the checksum value. use + * CHECSUM_UNNECESSARY. + */ + if ((netdev->features & NETIF_F_RXCSUM) && tcp_udp_csum_ok && + ipv4_csum_ok) + skb->ip_summed = CHECKSUM_UNNECESSARY; if (vlan_stripped) __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan_tci); -- cgit v1.2.3 From 92570438f512ad7ef883426aa0a784b0bb6bb382 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Fri, 2 Jan 2015 16:15:59 -0600 Subject: net: ethernet: cpsw: fix hangs with interrupts commit 7ce67a38f799d1fb332f672b117efbadedaa5352 upstream. The CPSW IP implements pulse-signaled interrupts. Due to that we must write a correct, pre-defined value to the CPDMA_MACEOIVECTOR register so the controller generates a pulse on the correct IRQ line to signal the End Of Interrupt. The way the driver is written today, all four IRQ lines are requested using the same IRQ handler and, because of that, we could fall into situations where a TX IRQ fires but we tell the controller that we ended an RX IRQ (or vice-versa). This situation triggers an IRQ storm on the reserved IRQ 127 of INTC which will in turn call ack_bad_irq() which will, then, print a ton of: unexpected IRQ trap at vector 00 In order to fix the problem, we are moving all calls to cpdma_ctlr_eoi() inside the IRQ handler and making sure we *always* write the correct value to the CPDMA_MACEOIVECTOR register. Note that the algorithm assumes that IRQ numbers and value-to-be-written-to-EOI are proportional, meaning that a write of value 0 would trigger an EOI pulse for the RX_THRESHOLD Interrupt and that's the IRQ number sitting in the 0-th index of our irqs_table array. This, however, is safe at least for current implementations of CPSW so we will refrain from making the check smarter (and, as a side-effect, slower) until we actually have a platform where IRQ lines are swapped. This patch has been tested for several days with AM335x- and AM437x-based platforms. AM57x was left out because there are still pending patches to enable ethernet in mainline for that platform. A read of the TRM confirms the statement on previous paragraph. Reported-by: Yegor Yefremov Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly) Signed-off-by: Felipe Balbi Acked-by: Tony Lindgren Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- drivers/net/ethernet/ti/cpsw.c | 19 ++++++++----------- 1 file changed, 8 insertions(+), 11 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index 921b9df2faca..4a2508e22218 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -716,6 +716,14 @@ static void cpsw_rx_handler(void *token, int len, int status) static irqreturn_t cpsw_interrupt(int irq, void *dev_id) { struct cpsw_priv *priv = dev_id; + int value = irq - priv->irqs_table[0]; + + /* NOTICE: Ending IRQ here. The trick with the 'value' variable above + * is to make sure we will always write the correct value to the EOI + * register. Namely 0 for RX_THRESH Interrupt, 1 for RX Interrupt, 2 + * for TX Interrupt and 3 for MISC Interrupt. + */ + cpdma_ctlr_eoi(priv->dma, value); cpsw_intr_disable(priv); if (priv->irq_enabled == true) { @@ -745,8 +753,6 @@ static int cpsw_poll(struct napi_struct *napi, int budget) int num_tx, num_rx; num_tx = cpdma_chan_process(priv->txch, 128); - if (num_tx) - cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_TX); num_rx = cpdma_chan_process(priv->rxch, budget); if (num_rx < budget) { @@ -754,7 +760,6 @@ static int cpsw_poll(struct napi_struct *napi, int budget) napi_complete(napi); cpsw_intr_enable(priv); - cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_RX); prim_cpsw = cpsw_get_slave_priv(priv, 0); if (prim_cpsw->irq_enabled == false) { prim_cpsw->irq_enabled = true; @@ -1265,8 +1270,6 @@ static int cpsw_ndo_open(struct net_device *ndev) napi_enable(&priv->napi); cpdma_ctlr_start(priv->dma); cpsw_intr_enable(priv); - cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_RX); - cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_TX); if (priv->data.dual_emac) priv->slaves[priv->emac_port].open_stat = true; @@ -1512,9 +1515,6 @@ static void cpsw_ndo_tx_timeout(struct net_device *ndev) cpdma_chan_start(priv->txch); cpdma_ctlr_int_ctrl(priv->dma, true); cpsw_intr_enable(priv); - cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_RX); - cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_TX); - } static int cpsw_ndo_set_mac_address(struct net_device *ndev, void *p) @@ -1560,9 +1560,6 @@ static void cpsw_ndo_poll_controller(struct net_device *ndev) cpsw_interrupt(ndev->irq, priv); cpdma_ctlr_int_ctrl(priv->dma, true); cpsw_intr_enable(priv); - cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_RX); - cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_TX); - } #endif -- cgit v1.2.3 From ef879ee1e6b874903ae2668da23b6c0e8c983c7e Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Tue, 13 Jan 2015 17:35:49 +0530 Subject: drivers: net: cpsw: fix multicast flush in dual emac mode commit 25906052d953d3fbdb7e19480b9de5e6bb949f3f upstream. Since ALE table is a common resource for both the interfaces in Dual EMAC mode and while bringing up the second interface in cpsw_ndo_set_rx_mode() all the multicast entries added by the first interface is flushed out and only second interface multicast addresses are added. Fixing this by flushing multicast addresses based on dual EMAC port vlans which will not affect the other emac port multicast addresses. Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation) Signed-off-by: Mugunthan V N Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- drivers/net/ethernet/ti/cpsw.c | 11 +++++++++-- drivers/net/ethernet/ti/cpsw_ale.c | 10 +++++++++- drivers/net/ethernet/ti/cpsw_ale.h | 2 +- 3 files changed, 19 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index 4a2508e22218..316650c3b5d7 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -596,7 +596,7 @@ static void cpsw_set_promiscious(struct net_device *ndev, bool enable) /* Clear all mcast from ALE */ cpsw_ale_flush_multicast(ale, ALE_ALL_PORTS << - priv->host_port); + priv->host_port, -1); /* Flood All Unicast Packets to Host port */ cpsw_ale_control_set(ale, 0, ALE_P0_UNI_FLOOD, 1); @@ -620,6 +620,12 @@ static void cpsw_set_promiscious(struct net_device *ndev, bool enable) static void cpsw_ndo_set_rx_mode(struct net_device *ndev) { struct cpsw_priv *priv = netdev_priv(ndev); + int vid; + + if (priv->data.dual_emac) + vid = priv->slaves[priv->emac_port].port_vlan; + else + vid = priv->data.default_vlan; if (ndev->flags & IFF_PROMISC) { /* Enable promiscuous mode */ @@ -631,7 +637,8 @@ static void cpsw_ndo_set_rx_mode(struct net_device *ndev) } /* Clear all mcast from ALE */ - cpsw_ale_flush_multicast(priv->ale, ALE_ALL_PORTS << priv->host_port); + cpsw_ale_flush_multicast(priv->ale, ALE_ALL_PORTS << priv->host_port, + vid); if (!netdev_mc_empty(ndev)) { struct netdev_hw_addr *ha; diff --git a/drivers/net/ethernet/ti/cpsw_ale.c b/drivers/net/ethernet/ti/cpsw_ale.c index 7f893069c418..4eceb7e42c80 100644 --- a/drivers/net/ethernet/ti/cpsw_ale.c +++ b/drivers/net/ethernet/ti/cpsw_ale.c @@ -236,7 +236,7 @@ static void cpsw_ale_flush_mcast(struct cpsw_ale *ale, u32 *ale_entry, cpsw_ale_set_entry_type(ale_entry, ALE_TYPE_FREE); } -int cpsw_ale_flush_multicast(struct cpsw_ale *ale, int port_mask) +int cpsw_ale_flush_multicast(struct cpsw_ale *ale, int port_mask, int vid) { u32 ale_entry[ALE_ENTRY_WORDS]; int ret, idx; @@ -247,6 +247,14 @@ int cpsw_ale_flush_multicast(struct cpsw_ale *ale, int port_mask) if (ret != ALE_TYPE_ADDR && ret != ALE_TYPE_VLAN_ADDR) continue; + /* if vid passed is -1 then remove all multicast entry from + * the table irrespective of vlan id, if a valid vlan id is + * passed then remove only multicast added to that vlan id. + * if vlan id doesn't match then move on to next entry. + */ + if (vid != -1 && cpsw_ale_get_vlan_id(ale_entry) != vid) + continue; + if (cpsw_ale_get_mcast(ale_entry)) { u8 addr[6]; diff --git a/drivers/net/ethernet/ti/cpsw_ale.h b/drivers/net/ethernet/ti/cpsw_ale.h index de409c33b250..e701358fd00b 100644 --- a/drivers/net/ethernet/ti/cpsw_ale.h +++ b/drivers/net/ethernet/ti/cpsw_ale.h @@ -88,7 +88,7 @@ void cpsw_ale_stop(struct cpsw_ale *ale); int cpsw_ale_set_ageout(struct cpsw_ale *ale, int ageout); int cpsw_ale_flush(struct cpsw_ale *ale, int port_mask); -int cpsw_ale_flush_multicast(struct cpsw_ale *ale, int port_mask); +int cpsw_ale_flush_multicast(struct cpsw_ale *ale, int port_mask, int vid); int cpsw_ale_add_ucast(struct cpsw_ale *ale, u8 *addr, int port, int flags, u16 vid); int cpsw_ale_del_ucast(struct cpsw_ale *ale, u8 *addr, int port, -- cgit v1.2.3