blob: 818e931f2b63f4fce4459c562017fb9d51a11635 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
|
.. _nucleo_f401re_board:
ST Nucleo F401RE
################
Overview
********
The Nucleo F401RE board features an ARM Cortex-M4 based STM32F401RE MCU
with a wide range of connectivity support and configurations Here are
some highlights of the Nucleo F401RE board:
- STM32 microcontroller in QFP64 package
- Two types of extension resources:
- Arduino Uno V3 connectivity
- ST morpho extension pin headers for full access to all STM32 I/Os
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
- Flexible board power supply:
- USB VBUS or external source(3.3V, 5V, 7 - 12V)
- Power management access point
- Three LEDs: USB communication (LD1), user LED (LD2), power LED (LD3)
- Two push-buttons: USER and RESET
.. image:: img/nucleo64_perf_logo_1024.png
:width: 720px
:align: center
:height: 720px
:alt: Nucleo F401RE
More information about the board can be found at the `Nucleo F401RE website`_.
Hardware
********
Nucleo F401RE provides the following hardware components:
- STM32F401RET6 in LQFP64 package
- ARM®32-bit Cortex®-M4 CPU with FPU
- 84 MHz max CPU frequency
- VDD from 1.7 V to 3.6 V
- 512 KB Flash
- 96 KB SRAM
- GPIO with external interrupt capability
- 12-bit ADC with 16 channels
- RTC
- Advanced-control Timer
- General Purpose Timers (7)
- Watchdog Timers (2)
- USART/UART (3)
- I2C (3)
- SPI (4)
- SDIO
- USB 2.0 OTG FS
- DMA Controller
More information about STM32F401RE can be found here:
- `STM32F401RE on www.st.com`_
- `STM32F401 reference manual`_
Supported Features
==================
The Zephyr nucleo_401re board configuration supports the following hardware features:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
| PINMUX | on-chip | pinmux |
+-----------+------------+-------------------------------------+
| GPIO | on-chip | gpio |
+-----------+------------+-------------------------------------+
| PWM | on-chip | pwm |
+-----------+------------+-------------------------------------+
Other hardware features are not yet supported on Zephyr porting.
The default configuration can be found in the defconfig file:
``boards/arm/nucleo_f401re/nucleo_f401re_defconfig``
Pin Mapping
===========
Nucleo F401RE Board has 6 GPIO controllers. These controllers are responsible for pin muxing,
input/output, pull-up, etc.
Available pins:
---------------
.. image:: img/nucleo_f401re_arduino.png
:width: 720px
:align: center
:height: 540px
:alt: Nucleo F401RE Arduino connectors
.. image:: img/nucleo_f401re_morpho.png
:width: 720px
:align: center
:height: 540px
:alt: Nucleo F401RE Morpho connectors
For mode details please refer to `STM32 Nucleo-64 board User Manual`_.
Default Zephyr Peripheral Mapping:
----------------------------------
- UART_1_TX : PB6
- UART_1_RX : PB7
- UART_2_TX : PA2
- UART_2_RX : PA3
- PWM_2_CH1 : PA0
- USER_PB : PC13
- LD2 : PA5
System Clock
============
Nucleo F401RE System Clock could be driven by internal or external oscillator,
as well as main PLL clock. By default System clock is driven by PLL clock at 84MHz,
driven by 8MHz high speed external clock.
Serial Port
===========
Nucleo F401RE board has 3 UARTs. The Zephyr console output is assigned to UART2.
Default settings are 115200 8N1.
Programming and Debugging
*************************
Flashing
========
Nucleo F401RE board includes an ST-LINK/V2-1 embedded debug tool interface.
This interface is supported by the openocd version included in Zephyr SDK.
Flashing an application to Nucleo F401RE
----------------------------------------
The sample application hello_world is being used in this tutorial:
.. code-block:: console
$<zephyr_root_path>/samples/hello_world
To build the Zephyr kernel and application, enter:
.. code-block:: console
$ cd <zephyr_root_path>
$ source zephyr-env.sh
$ cd $ZEPHYR_BASE/samples/hello_world/
$ make BOARD=nucleo_f401re
Connect the Nucleo F401RE to your host computer using the USB port.
Then, enter the following command:
.. code-block:: console
$ make BOARD=nucleo_f401re flash
Run a serial host program to connect with your Nucleo board:
.. code-block:: console
$ minicom -D /dev/ttyACM0
You should see the following message:
.. code-block:: console
Hello World! arm
Debugging
=========
Access gdb with the following make command:
.. code-block:: console
$ make BOARD=nucleo_f411re debug
.. _Nucleo F401RE website:
http://www.st.com/en/evaluation-tools/nucleo-f401re.html
.. _STM32 Nucleo-64 board User Manual:
http://www.st.com/resource/en/user_manual/dm00105823.pdf
.. _STM32F401RE on www.st.com:
http://www.st.com/en/microcontrollers/stm32f401re.html
.. _STM32F401 reference manual:
http://www.st.com/resource/en/reference_manual/dm00096844.pdf
|
