Merge tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel into drm-next

Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
  on gm45/vlv. Since this is a testing-only feature it should ever hurt,
  but I figured it'll help with regression-testing -fixes. So I left it
  in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
  conflict with the bdw stage 1 patches if I'd postpone this to -next.
  It's only an relatively small interface rework, so shouldn't cause pain.
  It's also been in my tree since almost 3 weeks already.

That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over

Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.

There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.

* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
  drm/i915/vlv: use per-pipe backlight controls v2
  drm/i915: make backlight functions take a connector
  drm/i915: move opregion asle request handling to a work queue
  drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
  drm/i915: Make intel_dp_is_edp() less specific
  drm/i915: Give names to the VBT child device type bits
  drm/i915/vlv: enable HDA display audio for Valleyview2
  drm/i915/dvo: call ->mode_set callback only when the port is running
  drm/i915: avoid unclaimed registers when capturing the error state
  drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
  drm/i915: scramble reset support for DP port CRC on vlv
  drm/i915: scramble reset support for DP port CRC on g4x
  drm/i916: add "auto" pipe CRC source
  ...

Conflicts:
	MAINTAINERS
	drivers/gpu/drm/i915/intel_panel.c
	drivers/gpu/drm/nouveau/core/subdev/mc/base.c
	drivers/gpu/drm/radeon/atombios_encoders.c
	drivers/gpu/drm/radeon/radeon_connectors.c

1 files changed, 17 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
index 2c6be0377f5..d2ea4605d07 100644
--- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
+++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
@@ -86,6 +86,7 @@ General Properties:
 
 Clock Properties:
 
+  - fsl,cksel        Timer reference clock source.
   - fsl,tclk-period  Timer reference clock period in nanoseconds.
   - fsl,tmr-prsc     Prescaler, divides the output clock.
   - fsl,tmr-add      Frequency compensation value.
@@ -97,7 +98,7 @@ Clock Properties:
   clock. You must choose these carefully for the clock to work right.
   Here is how to figure good values:
 
-  TimerOsc     = system clock               MHz
+  TimerOsc     = selected reference clock   MHz
   tclk_period  = desired clock period       nanoseconds
   NominalFreq  = 1000 / tclk_period         MHz
   FreqDivRatio = TimerOsc / NominalFreq     (must be greater that 1.0)
@@ -114,6 +115,20 @@ Clock Properties:
   Pulse Per Second (PPS) signal, since this will be offered to the PPS
   subsystem to synchronize the Linux clock.
 
+  Reference clock source is determined by the value, which is holded
+  in CKSEL bits in TMR_CTRL register. "fsl,cksel" property keeps the
+  value, which will be directly written in those bits, that is why,
+  according to reference manual, the next clock sources can be used:
+
+  <0> - external high precision timer reference clock (TSEC_TMR_CLK
+        input is used for this purpose);
+  <1> - eTSEC system clock;
+  <2> - eTSEC1 transmit clock;
+  <3> - RTC clock input.
+
+  When this attribute is not used, eTSEC system clock will serve as
+  IEEE 1588 timer reference clock.
+
 Example:
 
 	ptp_clock@24E00 {
@@ -121,6 +136,7 @@ Example:
 		reg = <0x24E00 0xB0>;
 		interrupts = <12 0x8 13 0x8>;
 		interrupt-parent = < &ipic >;
+		fsl,cksel       = <1>;
 		fsl,tclk-period = <10>;
 		fsl,tmr-prsc    = <100>;
 		fsl,tmr-add     = <0x999999A4>;