ARM: dt: tegra: paz00: add regulators

The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this.

Three data sources were used for the data encoded here:
* The HW defaults, as extracted from real HW.
* The schematic, which specifies a voltage for each rail in the signal
  names.
* The AC100 kernel used by the Ubuntu port:

  repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git
  branch chromeos-ac100-3.0
  file arch/arm/mach-tegra/board-paz00-power.c

  For many rails, the constraints in that tree specified differing min
  and max voltages. In all cases, the min value was ignored, since
  there's no need currently to vary any of the voltages at run-time.
  DVFS might change this in the future.

In most cases these sources all matched. Differences are:

sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max
of 1.3v, but this higher voltage was only applied to HW by DVFS code,
which isn't currently supported in mainline.

sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max
of 1.125v, but this higher voltage was only applied to HW by DVFS code,
which isn't currently supported in mainline.

ldo3: The HW default is on. marvin24's kernel didn't specify always-on,
but since the board wasn't marked as having fully constrained regulators,
the rail was not turned off, so the difference had no effect. The rail
is needed for USB.

ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However,
since this regulator is used for the same purpose as on other boards that
require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT
VDAC on Tegra, and so in practice is unlikely to be used, even though it
is actaully hooked up in HW.

Portions based on work by Laxman Dewangan <ldewangan@nvidia.com>

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Marc Dietrich <marvin24@gmx.de> # v2
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>

1 files changed, 173 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/tegra20-paz00.dts b/arch/arm/boot/dts/tegra20-paz00.dts
index 684a9e1ff7e..ddf287f52d4 100644
--- a/arch/arm/boot/dts/tegra20-paz00.dts
+++ b/arch/arm/boot/dts/tegra20-paz00.dts
@@ -272,12 +272,170 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
+		pmic: tps6586x@34 {
+			compatible = "ti,tps6586x";
+			reg = <0x34>;
+			interrupts = <0 86 0x4>;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			sys-supply = <&p5valw_reg>;
+			vin-sm0-supply = <&sys_reg>;
+			vin-sm1-supply = <&sys_reg>;
+			vin-sm2-supply = <&sys_reg>;
+			vinldo01-supply = <&sm2_reg>;
+			vinldo23-supply = <&sm2_reg>;
+			vinldo4-supply = <&sm2_reg>;
+			vinldo678-supply = <&sm2_reg>;
+			vinldo9-supply = <&sm2_reg>;
+
+			regulators {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sys_reg: regulator@0 {
+					reg = <0>;
+					regulator-compatible = "sys";
+					regulator-name = "vdd_sys";
+					regulator-always-on;
+				};
+
+				regulator@1 {
+					reg = <1>;
+					regulator-compatible = "sm0";
+					regulator-name = "+1.2vs_sm0,vdd_core";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				regulator@2 {
+					reg = <2>;
+					regulator-compatible = "sm1";
+					regulator-name = "+1.0vs_sm1,vdd_cpu";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				sm2_reg: regulator@3 {
+					reg = <3>;
+					regulator-compatible = "sm2";
+					regulator-name = "+3.7vs_sm2,vin_ldo*";
+					regulator-min-microvolt = <3700000>;
+					regulator-max-microvolt = <3700000>;
+					regulator-always-on;
+				};
+
+				/* LDO0 is not connected to anything */
+
+				regulator@5 {
+					reg = <5>;
+					regulator-compatible = "ldo1";
+					regulator-name = "+1.1vs_ldo1,avdd_pll*";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				regulator@6 {
+					reg = <6>;
+					regulator-compatible = "ldo2";
+					regulator-name = "+1.2vs_ldo2,vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				regulator@7 {
+					reg = <7>;
+					regulator-compatible = "ldo3";
+					regulator-name = "+3.3vs_ldo3,avdd_usb*";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				regulator@8 {
+					reg = <8>;
+					regulator-compatible = "ldo4";
+					regulator-name = "+1.8vs_ldo4,avdd_osc,vddio_sys";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				regulator@9 {
+					reg = <9>;
+					regulator-compatible = "ldo5";
+					regulator-name = "+2.85vs_ldo5,vcore_mmc";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+				};
+
+				regulator@10 {
+					reg = <10>;
+					regulator-compatible = "ldo6";
+					/*
+					 * Research indicates this should be
+					 * 1.8v; other boards that use this
+					 * rail for the same purpose need it
+					 * set to 1.8v. The schematic signal
+					 * name is incorrect; perhaps copied
+					 * from an incorrect NVIDIA reference.
+					 */
+					regulator-name = "+2.85vs_ldo6,avdd_vdac";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				regulator@11 {
+					reg = <11>;
+					regulator-compatible = "ldo7";
+					regulator-name = "+3.3vs_ldo7,avdd_hdmi";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				regulator@12 {
+					reg = <12>;
+					regulator-compatible = "ldo8";
+					regulator-name = "+1.8vs_ldo8,avdd_hdmi_pll";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				regulator@13 {
+					reg = <13>;
+					regulator-compatible = "ldo9";
+					regulator-name = "+2.85vs_ldo9,vdd_ddr_rx";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+				};
+
+				regulator@14 {
+					reg = <14>;
+					regulator-compatible = "ldo_rtc";
+					regulator-name = "+3.3vs_rtc";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+			};
+		};
+
 		adt7461@4c {
 			compatible = "adi,adt7461";
 			reg = <0x4c>;
 		};
 	};
 
+	pmc {
+		nvidia,invert-interrupt;
+	};
+
 	usb@c5000000 {
 		status = "okay";
 	};
@@ -325,6 +483,21 @@
 		};
 	};
 
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		p5valw_reg: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "+5valw";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+		};
+	};
+
 	sound {
 		compatible = "nvidia,tegra-audio-alc5632-paz00",
 			"nvidia,tegra-audio-alc5632";