Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc driver specific updates from Olof Johansson:
 "These changes are specific to some driver that may be used by multiple
  boards or socs.  The most significant change in here is the move of
  the samsung iommu code from a platform specific in-kernel interface to
  the generic iommu subsystem."

Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  mmc: dt: Consolidate DT bindings
  iommu/exynos: Add iommu driver for EXYNOS Platforms
  ARM: davinci: optimize the DMA ISR
  ARM: davinci: implement DEBUG_LL port choice
  ARM: tegra: Add SMMU enabler in AHB
  ARM: tegra: Add Tegra AHB driver
  Input: pxa27x_keypad add choice to set direct_key_mask
  Input: pxa27x_keypad direct key may be low active
  Input: pxa27x_keypad bug fix for direct_key_mask
  Input: pxa27x_keypad keep clock on as wakeup source
  ARM: dt: tegra: pinmux changes for USB ULPI
  ARM: tegra: add USB ULPI PHY reset GPIO to device tree
  ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
  ARM: tegra: change pll_p_out4's rate to 24MHz
  ARM: tegra: fix pclk rate
  ARM: tegra: reparent sclk to pll_c_out1
  ARM: tegra: Add pllc clock init table
  ARM: dt: tegra cardhu: basic audio support
  ARM: dt: tegra30.dtsi: Add audio-related nodes
  ARM: tegra: add AUXDATA required for audio
  ...

3 files changed, 146 insertions, 53 deletions

diff --git a/arch/arm/mach-tegra/include/mach/tegra-ahb.h b/arch/arm/mach-tegra/include/mach/tegra-ahb.h
new file mode 100644
index 00000000000..e0f8c84b1d8
--- /dev/null
+++ b/arch/arm/mach-tegra/include/mach/tegra-ahb.h
@@ -0,0 +1,19 @@
+/*
+ * Copyright (c) 2012, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ */
+
+#ifndef __MACH_TEGRA_AHB_H__
+#define __MACH_TEGRA_AHB_H__
+
+extern int tegra_ahb_enable_smmu(struct device_node *ahb);
+
+#endif	/* __MACH_TEGRA_AHB_H__ */
diff --git a/arch/arm/mach-tegra/include/mach/uncompress.h b/arch/arm/mach-tegra/include/mach/uncompress.h
index 5a440f315e5..937c4c50219 100644
--- a/arch/arm/mach-tegra/include/mach/uncompress.h
+++ b/arch/arm/mach-tegra/include/mach/uncompress.h
@@ -63,52 +63,86 @@ static inline void save_uart_address(void)
 		buf[0] = 0;
 }
 
-/*
- * Setup before decompression.  This is where we do UART selection for
- * earlyprintk and init the uart_base register.
- */
-static inline void arch_decomp_setup(void)
+static const struct {
+	u32 base;
+	u32 reset_reg;
+	u32 clock_reg;
+	u32 bit;
+} uarts[] = {
+	{
+		TEGRA_UARTA_BASE,
+		TEGRA_CLK_RESET_BASE + 0x04,
+		TEGRA_CLK_RESET_BASE + 0x10,
+		6,
+	},
+	{
+		TEGRA_UARTB_BASE,
+		TEGRA_CLK_RESET_BASE + 0x04,
+		TEGRA_CLK_RESET_BASE + 0x10,
+		7,
+	},
+	{
+		TEGRA_UARTC_BASE,
+		TEGRA_CLK_RESET_BASE + 0x08,
+		TEGRA_CLK_RESET_BASE + 0x14,
+		23,
+	},
+	{
+		TEGRA_UARTD_BASE,
+		TEGRA_CLK_RESET_BASE + 0x0c,
+		TEGRA_CLK_RESET_BASE + 0x18,
+		1,
+	},
+	{
+		TEGRA_UARTE_BASE,
+		TEGRA_CLK_RESET_BASE + 0x0c,
+		TEGRA_CLK_RESET_BASE + 0x18,
+		2,
+	},
+};
+
+static inline bool uart_clocked(int i)
+{
+	if (*(u8 *)uarts[i].reset_reg & BIT(uarts[i].bit))
+		return false;
+
+	if (!(*(u8 *)uarts[i].clock_reg & BIT(uarts[i].bit)))
+		return false;
+
+	return true;
+}
+
+#ifdef CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA
+int auto_odmdata(void)
+{
+	volatile u32 *pmc = (volatile u32 *)TEGRA_PMC_BASE;
+	u32 odmdata = pmc[0xa0 / 4];
+
+	/*
+	 * Bits 19:18 are the console type: 0=default, 1=none, 2==DCC, 3==UART
+	 * Some boards apparently swap the last two values, but we don't have
+	 * any way of catering for that here, so we just accept either. If this
+	 * doesn't make sense for your board, just don't enable this feature.
+	 *
+	 * Bits 17:15 indicate the UART to use, 0/1/2/3/4 are UART A/B/C/D/E.
+	 */
+
+	switch  ((odmdata >> 18) & 3) {
+	case 2:
+	case 3:
+		break;
+	default:
+		return -1;
+	}
+
+	return (odmdata >> 15) & 7;
+}
+#endif
+
+#ifdef CONFIG_TEGRA_DEBUG_UART_AUTO_SCRATCH
+int auto_scratch(void)
 {
-	static const struct {
-		u32 base;
-		u32 reset_reg;
-		u32 clock_reg;
-		u32 bit;
-	} uarts[] = {
-		{
-			TEGRA_UARTA_BASE,
-			TEGRA_CLK_RESET_BASE + 0x04,
-			TEGRA_CLK_RESET_BASE + 0x10,
-			6,
-		},
-		{
-			TEGRA_UARTB_BASE,
-			TEGRA_CLK_RESET_BASE + 0x04,
-			TEGRA_CLK_RESET_BASE + 0x10,
-			7,
-		},
-		{
-			TEGRA_UARTC_BASE,
-			TEGRA_CLK_RESET_BASE + 0x08,
-			TEGRA_CLK_RESET_BASE + 0x14,
-			23,
-		},
-		{
-			TEGRA_UARTD_BASE,
-			TEGRA_CLK_RESET_BASE + 0x0c,
-			TEGRA_CLK_RESET_BASE + 0x18,
-			1,
-		},
-		{
-			TEGRA_UARTE_BASE,
-			TEGRA_CLK_RESET_BASE + 0x0c,
-			TEGRA_CLK_RESET_BASE + 0x18,
-			2,
-		},
-	};
 	int i;
-	volatile u32 *apb_misc = (volatile u32 *)TEGRA_APB_MISC_BASE;
-	u32 chip, div;
 
 	/*
 	 * Look for the first UART that:
@@ -125,20 +159,60 @@ static inline void arch_decomp_setup(void)
 	 * back to what's specified in TEGRA_DEBUG_UART_BASE.
 	 */
 	for (i = 0; i < ARRAY_SIZE(uarts); i++) {
-		if (*(u8 *)uarts[i].reset_reg & BIT(uarts[i].bit))
-			continue;
-
-		if (!(*(u8 *)uarts[i].clock_reg & BIT(uarts[i].bit)))
+		if (!uart_clocked(i))
 			continue;
 
 		uart = (volatile u8 *)uarts[i].base;
 		if (uart[UART_SCR << DEBUG_UART_SHIFT] != 'D')
 			continue;
 
-		break;
+		return i;
 	}
-	if (i == ARRAY_SIZE(uarts))
-		uart = (volatile u8 *)TEGRA_DEBUG_UART_BASE;
+
+	return -1;
+}
+#endif
+
+/*
+ * Setup before decompression.  This is where we do UART selection for
+ * earlyprintk and init the uart_base register.
+ */
+static inline void arch_decomp_setup(void)
+{
+	int uart_id, auto_uart_id;
+	volatile u32 *apb_misc = (volatile u32 *)TEGRA_APB_MISC_BASE;
+	u32 chip, div;
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTA)
+	uart_id = 0;
+#elif defined(CONFIG_TEGRA_DEBUG_UARTB)
+	uart_id = 1;
+#elif defined(CONFIG_TEGRA_DEBUG_UARTC)
+	uart_id = 2;
+#elif defined(CONFIG_TEGRA_DEBUG_UARTD)
+	uart_id = 3;
+#elif defined(CONFIG_TEGRA_DEBUG_UARTE)
+	uart_id = 4;
+#else
+	uart_id = -1;
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+	auto_uart_id = auto_odmdata();
+#elif defined(CONFIG_TEGRA_DEBUG_UART_AUTO_SCRATCH)
+	auto_uart_id = auto_scratch();
+#else
+	auto_uart_id = -1;
+#endif
+	if (auto_uart_id != -1)
+		uart_id = auto_uart_id;
+
+	if (uart_id < 0 || uart_id >= ARRAY_SIZE(uarts) ||
+	    !uart_clocked(uart_id))
+		uart = NULL;
+	else
+		uart = (volatile u8 *)uarts[uart_id].base;
+
 	save_uart_address();
 	if (uart == NULL)
 		return;
diff --git a/arch/arm/mach-tegra/include/mach/usb_phy.h b/arch/arm/mach-tegra/include/mach/usb_phy.h
index de1a0f602b2..935ce9f6559 100644
--- a/arch/arm/mach-tegra/include/mach/usb_phy.h
+++ b/arch/arm/mach-tegra/include/mach/usb_phy.h
@@ -61,8 +61,8 @@ struct tegra_usb_phy {
 	struct usb_phy *ulpi;
 };
 
-struct tegra_usb_phy *tegra_usb_phy_open(int instance, void __iomem *regs,
-			void *config, enum tegra_usb_phy_mode phy_mode);
+struct tegra_usb_phy *tegra_usb_phy_open(struct device *dev, int instance,
+	void __iomem *regs, void *config, enum tegra_usb_phy_mode phy_mode);
 
 int tegra_usb_phy_power_on(struct tegra_usb_phy *phy);