Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC bug fixes from Arnd Bergmann:
 "After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
  sent urgent fixes for 3.9.  I pushed back on a number of them that got
  deferred to 3.10, but these are the ones that seemed important.

  Regression in 3.9:

   - Multiple regressions in OMAP2+ clock cleanup
   - SH-Mobile frame buffer bug fix that merged here because of
     maintainer MIA
   - ux500 prcmu changes broke DT booting
   - MMCI duplicated regulator setup on ux500
   - New ux500 clock driver broke ethernet on snowball
   - Local interrupt driver for mvebu broke ethernet
   - MVEBU GPIO driver did not get set up right on Orion DT
   - incorrect interrupt number on Orion crypto for DT

  Long-standing bugs, including candidates for stable:

   - Kirkwood MMC needs to disable invalid card detect pins
   - MV SDIO pinmux was wrong on Mirabox
   - GoFlex Net board file needs to set NAND chip delay
   - MSM timer restart race
   - ep93xx early debug code broke in 3.7
   - i.MX CPU hotplug race
   - Incorrect clock setup for OMAP1 USB
   - Workaround for bad clock setup by some old OMAP4 boot loaders
   - Static I/O mappings on cns3xxx since 3.2"

* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: cns3xxx: fix mapping of private memory region
  arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
  arm: orion5x: correct IRQ used in dtsi for mv_cesa
  arm: orion5x: fix orion5x.dtsi gpio parameters
  ARM: Kirkwood: fix unused mvsdio gpio pins
  arm: mvebu: Use local interrupt only for the timer 0
  ARM: kirkwood: Fix chip-delay for GoFlex Net
  ARM: ux500: Enable the clock controlling Ethernet on Snowball
  ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
  ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
  fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
  ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
  ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
  ARM: msm: Stop counting before reprogramming clockevent
  ARM: ep93xx: Fix wait for UART FIFO to be empty
  ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
  ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
  ARM: OMAP4: clock data: lock USB DPLL on boot
  ARM: OMAP1: fix USB host on 1710

29 files changed, 154 insertions, 58 deletions

diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/armada-370-mirabox.dts
index dd0c57dd9f3..3234875824d 100644
--- a/arch/arm/boot/dts/armada-370-mirabox.dts
+++ b/arch/arm/boot/dts/armada-370-mirabox.dts
@@ -54,7 +54,7 @@
 		};
 
 		mvsdio@d00d4000 {
-			pinctrl-0 = <&sdio_pins2>;
+			pinctrl-0 = <&sdio_pins3>;
 			pinctrl-names = "default";
 			status = "okay";
 			/*
diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi
index 8188d138020..a195debb67d 100644
--- a/arch/arm/boot/dts/armada-370.dtsi
+++ b/arch/arm/boot/dts/armada-370.dtsi
@@ -59,6 +59,12 @@
 					     "mpp50", "mpp51", "mpp52";
 			      marvell,function = "sd0";
 			};
+
+			sdio_pins3: sdio-pins3 {
+			      marvell,pins = "mpp48", "mpp49", "mpp50",
+					     "mpp51", "mpp52", "mpp53";
+			      marvell,function = "sd0";
+			};
 	        };
 
 		gpio0: gpio@d0018100 {
diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
index 9de93096601..aaa63d0a809 100644
--- a/arch/arm/boot/dts/dbx5x0.dtsi
+++ b/arch/arm/boot/dts/dbx5x0.dtsi
@@ -191,8 +191,8 @@
 
 		prcmu: prcmu@80157000 {
 			compatible = "stericsson,db8500-prcmu";
-			reg = <0x80157000 0x1000>;
-			reg-names = "prcmu";
+			reg = <0x80157000 0x1000>, <0x801b0000 0x8000>, <0x801b8000 0x1000>;
+			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm";
 			interrupts = <0 47 0x4>;
 			#address-cells = <1>;
 			#size-cells = <1>;
diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts
index bd83b8fc7c8..c3573be7b92 100644
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
@@ -77,6 +77,7 @@
 		};
 
 		nand@3000000 {
+			chip-delay = <40>;
 			status = "okay";
 
 			partition@0 {
diff --git a/arch/arm/boot/dts/orion5x.dtsi b/arch/arm/boot/dts/orion5x.dtsi
index 8aad00f81ed..f7bec3b1ba3 100644
--- a/arch/arm/boot/dts/orion5x.dtsi
+++ b/arch/arm/boot/dts/orion5x.dtsi
@@ -13,6 +13,9 @@
 	compatible = "marvell,orion5x";
 	interrupt-parent = <&intc>;
 
+	aliases {
+		gpio0 = &gpio0;
+	};
 	intc: interrupt-controller {
 		compatible = "marvell,orion-intc", "marvell,intc";
 		interrupt-controller;
@@ -32,7 +35,9 @@
 			#gpio-cells = <2>;
 			gpio-controller;
 			reg = <0x10100 0x40>;
-			ngpio = <32>;
+			ngpios = <32>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <6>, <7>, <8>, <9>;
 		};
 
@@ -91,7 +96,7 @@
 			reg = <0x90000 0x10000>,
 			      <0xf2200000 0x800>;
 			reg-names = "regs", "sram";
-			interrupts = <22>;
+			interrupts = <28>;
 			status = "okay";
 		};
 	};
diff --git a/arch/arm/mach-cns3xxx/core.c b/arch/arm/mach-cns3xxx/core.c
index e698f26cc0c..52e4bb5cf12 100644
--- a/arch/arm/mach-cns3xxx/core.c
+++ b/arch/arm/mach-cns3xxx/core.c
@@ -22,19 +22,9 @@
 
 static struct map_desc cns3xxx_io_desc[] __initdata = {
 	{
-		.virtual	= CNS3XXX_TC11MP_TWD_BASE_VIRT,
-		.pfn		= __phys_to_pfn(CNS3XXX_TC11MP_TWD_BASE),
-		.length		= SZ_4K,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT,
-		.pfn		= __phys_to_pfn(CNS3XXX_TC11MP_GIC_CPU_BASE),
-		.length		= SZ_4K,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT,
-		.pfn		= __phys_to_pfn(CNS3XXX_TC11MP_GIC_DIST_BASE),
-		.length		= SZ_4K,
+		.virtual	= CNS3XXX_TC11MP_SCU_BASE_VIRT,
+		.pfn		= __phys_to_pfn(CNS3XXX_TC11MP_SCU_BASE),
+		.length		= SZ_8K,
 		.type		= MT_DEVICE,
 	}, {
 		.virtual	= CNS3XXX_TIMER1_2_3_BASE_VIRT,
diff --git a/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h
index 191c8e57f28..b1021aafa48 100644
--- a/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h
+++ b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h
@@ -94,10 +94,10 @@
 #define RTC_INTR_STS_OFFSET			0x34
 
 #define CNS3XXX_MISC_BASE			0x76000000	/* Misc Control */
-#define CNS3XXX_MISC_BASE_VIRT			0xFFF07000	/* Misc Control */
+#define CNS3XXX_MISC_BASE_VIRT			0xFB000000	/* Misc Control */
 
 #define CNS3XXX_PM_BASE				0x77000000	/* Power Management Control */
-#define CNS3XXX_PM_BASE_VIRT			0xFFF08000
+#define CNS3XXX_PM_BASE_VIRT			0xFB001000
 
 #define PM_CLK_GATE_OFFSET			0x00
 #define PM_SOFT_RST_OFFSET			0x04
@@ -109,7 +109,7 @@
 #define PM_PLL_HM_PD_OFFSET			0x1C
 
 #define CNS3XXX_UART0_BASE			0x78000000	/* UART 0 */
-#define CNS3XXX_UART0_BASE_VIRT			0xFFF09000
+#define CNS3XXX_UART0_BASE_VIRT			0xFB002000
 
 #define CNS3XXX_UART1_BASE			0x78400000	/* UART 1 */
 #define CNS3XXX_UART1_BASE_VIRT			0xFFF0A000
@@ -130,7 +130,7 @@
 #define CNS3XXX_I2S_BASE_VIRT			0xFFF10000
 
 #define CNS3XXX_TIMER1_2_3_BASE			0x7C800000	/* Timer */
-#define CNS3XXX_TIMER1_2_3_BASE_VIRT		0xFFF10800
+#define CNS3XXX_TIMER1_2_3_BASE_VIRT		0xFB003000
 
 #define TIMER1_COUNTER_OFFSET			0x00
 #define TIMER1_AUTO_RELOAD_OFFSET		0x04
@@ -227,16 +227,16 @@
  * Testchip peripheral and fpga gic regions
  */
 #define CNS3XXX_TC11MP_SCU_BASE			0x90000000	/* IRQ, Test chip */
-#define CNS3XXX_TC11MP_SCU_BASE_VIRT		0xFF000000
+#define CNS3XXX_TC11MP_SCU_BASE_VIRT		0xFB004000
 
 #define CNS3XXX_TC11MP_GIC_CPU_BASE		0x90000100	/* Test chip interrupt controller CPU interface */
-#define CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT	0xFF000100
+#define CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT	(CNS3XXX_TC11MP_SCU_BASE_VIRT + 0x100)
 
 #define CNS3XXX_TC11MP_TWD_BASE			0x90000600
-#define CNS3XXX_TC11MP_TWD_BASE_VIRT		0xFF000600
+#define CNS3XXX_TC11MP_TWD_BASE_VIRT		(CNS3XXX_TC11MP_SCU_BASE_VIRT + 0x600)
 
 #define CNS3XXX_TC11MP_GIC_DIST_BASE		0x90001000	/* Test chip interrupt controller distributor */
-#define CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT	0xFF001000
+#define CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT	(CNS3XXX_TC11MP_SCU_BASE_VIRT + 0x1000)
 
 #define CNS3XXX_TC11MP_L220_BASE		0x92002000	/* L220 registers */
 #define CNS3XXX_TC11MP_L220_BASE_VIRT		0xFF002000
diff --git a/arch/arm/mach-ep93xx/include/mach/uncompress.h b/arch/arm/mach-ep93xx/include/mach/uncompress.h
index d2afb4dd82a..b5cc77d2380 100644
--- a/arch/arm/mach-ep93xx/include/mach/uncompress.h
+++ b/arch/arm/mach-ep93xx/include/mach/uncompress.h
@@ -47,9 +47,13 @@ static void __raw_writel(unsigned int value, unsigned int ptr)
 
 static inline void putc(int c)
 {
-	/* Transmit fifo not full?  */
-	while (__raw_readb(PHYS_UART_FLAG) & UART_FLAG_TXFF)
-		;
+	int i;
+
+	for (i = 0; i < 10000; i++) {
+		/* Transmit fifo not full? */
+		if (!(__raw_readb(PHYS_UART_FLAG) & UART_FLAG_TXFF))
+			break;
+	}
 
 	__raw_writeb(c, PHYS_UART_DATA);
 }
diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
index 5a800bfcec5..5bf4a97ab24 100644
--- a/arch/arm/mach-imx/common.h
+++ b/arch/arm/mach-imx/common.h
@@ -110,6 +110,8 @@ void tzic_handle_irq(struct pt_regs *);
 
 extern void imx_enable_cpu(int cpu, bool enable);
 extern void imx_set_cpu_jump(int cpu, void *jump_addr);
+extern u32 imx_get_cpu_arg(int cpu);
+extern void imx_set_cpu_arg(int cpu, u32 arg);
 extern void v7_cpu_resume(void);
 extern u32 *pl310_get_save_ptr(void);
 #ifdef CONFIG_SMP
diff --git a/arch/arm/mach-imx/hotplug.c b/arch/arm/mach-imx/hotplug.c
index 7bc5fe15dda..361a253e2b6 100644
--- a/arch/arm/mach-imx/hotplug.c
+++ b/arch/arm/mach-imx/hotplug.c
@@ -46,11 +46,23 @@ static inline void cpu_enter_lowpower(void)
 void imx_cpu_die(unsigned int cpu)
 {
 	cpu_enter_lowpower();
+	/*
+	 * We use the cpu jumping argument register to sync with
+	 * imx_cpu_kill() which is running on cpu0 and waiting for
+	 * the register being cleared to kill the cpu.
+	 */
+	imx_set_cpu_arg(cpu, ~0);
 	cpu_do_idle();
 }
 
 int imx_cpu_kill(unsigned int cpu)
 {
+	unsigned long timeout = jiffies + msecs_to_jiffies(50);
+
+	while (imx_get_cpu_arg(cpu) == 0)
+		if (time_after(jiffies, timeout))
+			return 0;
 	imx_enable_cpu(cpu, false);
+	imx_set_cpu_arg(cpu, 0);
 	return 1;
 }
diff --git a/arch/arm/mach-imx/src.c b/arch/arm/mach-imx/src.c
index e15f1555c59..09a742f8c7a 100644
--- a/arch/arm/mach-imx/src.c
+++ b/arch/arm/mach-imx/src.c
@@ -43,6 +43,18 @@ void imx_set_cpu_jump(int cpu, void *jump_addr)
 		       src_base + SRC_GPR1 + cpu * 8);
 }
 
+u32 imx_get_cpu_arg(int cpu)
+{
+	cpu = cpu_logical_map(cpu);
+	return readl_relaxed(src_base + SRC_GPR1 + cpu * 8 + 4);
+}
+
+void imx_set_cpu_arg(int cpu, u32 arg)
+{
+	cpu = cpu_logical_map(cpu);
+	writel_relaxed(arg, src_base + SRC_GPR1 + cpu * 8 + 4);
+}
+
 void imx_src_prepare_restart(void)
 {
 	u32 val;
diff --git a/arch/arm/mach-kirkwood/guruplug-setup.c b/arch/arm/mach-kirkwood/guruplug-setup.c
index 1c6e736cbbf..08dd739aa70 100644
--- a/arch/arm/mach-kirkwood/guruplug-setup.c
+++ b/arch/arm/mach-kirkwood/guruplug-setup.c
@@ -53,6 +53,8 @@ static struct mv_sata_platform_data guruplug_sata_data = {
 
 static struct mvsdio_platform_data guruplug_mvsdio_data = {
 	/* unfortunately the CD signal has not been connected */
+	.gpio_card_detect = -1,
+	.gpio_write_protect = -1,
 };
 
 static struct gpio_led guruplug_led_pins[] = {
diff --git a/arch/arm/mach-kirkwood/openrd-setup.c b/arch/arm/mach-kirkwood/openrd-setup.c
index 8ddd69fdc93..6a6eb548307 100644
--- a/arch/arm/mach-kirkwood/openrd-setup.c
+++ b/arch/arm/mach-kirkwood/openrd-setup.c
@@ -55,6 +55,7 @@ static struct mv_sata_platform_data openrd_sata_data = {
 
 static struct mvsdio_platform_data openrd_mvsdio_data = {
 	.gpio_card_detect = 29,	/* MPP29 used as SD card detect */
+	.gpio_write_protect = -1,
 };
 
 static unsigned int openrd_mpp_config[] __initdata = {
diff --git a/arch/arm/mach-kirkwood/rd88f6281-setup.c b/arch/arm/mach-kirkwood/rd88f6281-setup.c
index c7d93b48926..d24223166e0 100644
--- a/arch/arm/mach-kirkwood/rd88f6281-setup.c
+++ b/arch/arm/mach-kirkwood/rd88f6281-setup.c
@@ -69,6 +69,7 @@ static struct mv_sata_platform_data rd88f6281_sata_data = {
 
 static struct mvsdio_platform_data rd88f6281_mvsdio_data = {
 	.gpio_card_detect = 28,
+	.gpio_write_protect = -1,
 };
 
 static unsigned int rd88f6281_mpp_config[] __initdata = {
diff --git a/arch/arm/mach-msm/timer.c b/arch/arm/mach-msm/timer.c
index 2969027f02f..f9fd77e8f1f 100644
--- a/arch/arm/mach-msm/timer.c
+++ b/arch/arm/mach-msm/timer.c
@@ -62,7 +62,10 @@ static int msm_timer_set_next_event(unsigned long cycles,
 {
 	u32 ctrl = readl_relaxed(event_base + TIMER_ENABLE);
 
-	writel_relaxed(0, event_base + TIMER_CLEAR);
+	ctrl &= ~TIMER_ENABLE_EN;
+	writel_relaxed(ctrl, event_base + TIMER_ENABLE);
+
+	writel_relaxed(ctrl, event_base + TIMER_CLEAR);
 	writel_relaxed(cycles, event_base + TIMER_MATCH_VAL);
 	writel_relaxed(ctrl | TIMER_ENABLE_EN, event_base + TIMER_ENABLE);
 	return 0;
diff --git a/arch/arm/mach-mvebu/irq-armada-370-xp.c b/arch/arm/mach-mvebu/irq-armada-370-xp.c
index 274ff58271d..6a9195e1057 100644
--- a/arch/arm/mach-mvebu/irq-armada-370-xp.c
+++ b/arch/arm/mach-mvebu/irq-armada-370-xp.c
@@ -44,6 +44,8 @@
 
 #define ARMADA_370_XP_MAX_PER_CPU_IRQS		(28)
 
+#define ARMADA_370_XP_TIMER0_PER_CPU_IRQ	(5)
+
 #define ACTIVE_DOORBELLS			(8)
 
 static DEFINE_RAW_SPINLOCK(irq_controller_lock);
@@ -62,7 +64,7 @@ static void armada_370_xp_irq_mask(struct irq_data *d)
 #ifdef CONFIG_SMP
 	irq_hw_number_t hwirq = irqd_to_hwirq(d);
 
-	if (hwirq > ARMADA_370_XP_MAX_PER_CPU_IRQS)
+	if (hwirq != ARMADA_370_XP_TIMER0_PER_CPU_IRQ)
 		writel(hwirq, main_int_base +
 				ARMADA_370_XP_INT_CLEAR_ENABLE_OFFS);
 	else
@@ -79,7 +81,7 @@ static void armada_370_xp_irq_unmask(struct irq_data *d)
 #ifdef CONFIG_SMP
 	irq_hw_number_t hwirq = irqd_to_hwirq(d);
 
-	if (hwirq > ARMADA_370_XP_MAX_PER_CPU_IRQS)
+	if (hwirq != ARMADA_370_XP_TIMER0_PER_CPU_IRQ)
 		writel(hwirq, main_int_base +
 				ARMADA_370_XP_INT_SET_ENABLE_OFFS);
 	else
@@ -147,7 +149,7 @@ static int armada_370_xp_mpic_irq_map(struct irq_domain *h,
 	writel(hw, main_int_base + ARMADA_370_XP_INT_SET_ENABLE_OFFS);
 	irq_set_status_flags(virq, IRQ_LEVEL);
 
-	if (hw < ARMADA_370_XP_MAX_PER_CPU_IRQS) {
+	if (hw == ARMADA_370_XP_TIMER0_PER_CPU_IRQ) {
 		irq_set_percpu_devid(virq);
 		irq_set_chip_and_handler(virq, &armada_370_xp_irq_chip,
 					handle_percpu_devid_irq);
diff --git a/arch/arm/mach-omap1/clock_data.c b/arch/arm/mach-omap1/clock_data.c
index cb7c6ae2e3f..6c4f766365a 100644
--- a/arch/arm/mach-omap1/clock_data.c
+++ b/arch/arm/mach-omap1/clock_data.c
@@ -543,15 +543,6 @@ static struct clk usb_dc_ck = {
 	/* Direct from ULPD, no parent */
 	.rate		= 48000000,
 	.enable_reg	= OMAP1_IO_ADDRESS(SOFT_REQ_REG),
-	.enable_bit	= USB_REQ_EN_SHIFT,
-};
-
-static struct clk usb_dc_ck7xx = {
-	.name		= "usb_dc_ck",
-	.ops		= &clkops_generic,
-	/* Direct from ULPD, no parent */
-	.rate		= 48000000,
-	.enable_reg	= OMAP1_IO_ADDRESS(SOFT_REQ_REG),
 	.enable_bit	= SOFT_USB_OTG_DPLL_REQ_SHIFT,
 };
 
@@ -727,8 +718,7 @@ static struct omap_clk omap_clks[] = {
 	CLK(NULL,	"usb_clko",	&usb_clko,	CK_16XX | CK_1510 | CK_310),
 	CLK(NULL,	"usb_hhc_ck",	&usb_hhc_ck1510, CK_1510 | CK_310),
 	CLK(NULL,	"usb_hhc_ck",	&usb_hhc_ck16xx, CK_16XX),
-	CLK(NULL,	"usb_dc_ck",	&usb_dc_ck,	CK_16XX),
-	CLK(NULL,	"usb_dc_ck",	&usb_dc_ck7xx,	CK_7XX),
+	CLK(NULL,	"usb_dc_ck",	&usb_dc_ck,	CK_16XX | CK_7XX),
 	CLK(NULL,	"mclk",		&mclk_1510,	CK_1510 | CK_310),
 	CLK(NULL,	"mclk",		&mclk_16xx,	CK_16XX),
 	CLK(NULL,	"bclk",		&bclk_1510,	CK_1510 | CK_310),
diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c
index 3d58f335f17..0c6834ae1fc 100644
--- a/arch/arm/mach-omap2/cclock44xx_data.c
+++ b/arch/arm/mach-omap2/cclock44xx_data.c
@@ -52,6 +52,13 @@
  */
 #define OMAP4_DPLL_ABE_DEFFREQ				98304000
 
+/*
+ * OMAP4 USB DPLL default frequency. In OMAP4430 TRM version V, section
+ * "3.6.3.9.5 DPLL_USB Preferred Settings" shows that the preferred
+ * locked frequency for the USB DPLL is 960MHz.
+ */
+#define OMAP4_DPLL_USB_DEFFREQ				960000000
+
 /* Root clocks */
 
 DEFINE_CLK_FIXED_RATE(extalt_clkin_ck, CLK_IS_ROOT, 59000000, 0x0);
@@ -1011,6 +1018,10 @@ DEFINE_CLK_OMAP_MUX(hsmmc2_fclk, "l3_init_clkdm", hsmmc1_fclk_sel,
 		    OMAP4430_CM_L3INIT_MMC2_CLKCTRL, OMAP4430_CLKSEL_MASK,
 		    hsmmc1_fclk_parents, func_dmic_abe_gfclk_ops);
 
+DEFINE_CLK_GATE(ocp2scp_usb_phy_phy_48m, "func_48m_fclk", &func_48m_fclk, 0x0,
+		OMAP4430_CM_L3INIT_USBPHYOCP2SCP_CLKCTRL,
+		OMAP4430_OPTFCLKEN_PHY_48M_SHIFT, 0x0, NULL);
+
 DEFINE_CLK_GATE(sha2md5_fck, "l3_div_ck", &l3_div_ck, 0x0,
 		OMAP4430_CM_L4SEC_SHA2MD51_CLKCTRL,
 		OMAP4430_MODULEMODE_SWCTRL_SHIFT, 0x0, NULL);
@@ -1538,6 +1549,7 @@ static struct omap_clk omap44xx_clks[] = {
 	CLK(NULL,	"per_mcbsp4_gfclk",			&per_mcbsp4_gfclk,	CK_443X),
 	CLK(NULL,	"hsmmc1_fclk",			&hsmmc1_fclk,	CK_443X),
 	CLK(NULL,	"hsmmc2_fclk",			&hsmmc2_fclk,	CK_443X),
+	CLK(NULL,	"ocp2scp_usb_phy_phy_48m",	&ocp2scp_usb_phy_phy_48m,	CK_443X),
 	CLK(NULL,	"sha2md5_fck",			&sha2md5_fck,	CK_443X),
 	CLK(NULL,	"slimbus1_fclk_1",		&slimbus1_fclk_1,	CK_443X),
 	CLK(NULL,	"slimbus1_fclk_0",		&slimbus1_fclk_0,	CK_443X),
@@ -1705,5 +1717,13 @@ int __init omap4xxx_clk_init(void)
 	if (rc)
 		pr_err("%s: failed to configure ABE DPLL!\n", __func__);
 
+	/*
+	 * Lock USB DPLL on OMAP4 devices so that the L3INIT power
+	 * domain can transition to retention state when not in use.
+	 */
+	rc = clk_set_rate(&dpll_usb_ck, OMAP4_DPLL_USB_DEFFREQ);
+	if (rc)
+		pr_err("%s: failed to configure USB DPLL!\n", __func__);
+
 	return 0;
 }
diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h
index 40f4a03d728..d6ba13e1c54 100644
--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -293,5 +293,8 @@ extern void omap_reserve(void);
 struct omap_hwmod;
 extern int omap_dss_reset(struct omap_hwmod *);
 
+/* SoC specific clock initializer */
+extern int (*omap_clk_init)(void);
+
 #endif /* __ASSEMBLER__ */
 #endif /* __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H */
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index 2c3fdd65387..5c445ca1e27 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -55,6 +55,12 @@
 #include "prm44xx.h"
 
 /*
+ * omap_clk_init: points to a function that does the SoC-specific
+ * clock initializations
+ */
+int (*omap_clk_init)(void);
+
+/*
  * The machine specific code may provide the extra mapping besides the
  * default mapping provided here.
  */
@@ -397,7 +403,7 @@ void __init omap2420_init_early(void)
 	omap242x_clockdomains_init();
 	omap2420_hwmod_init();
 	omap_hwmod_init_postsetup();
-	omap2420_clk_init();
+	omap_clk_init = omap2420_clk_init;
 }
 
 void __init omap2420_init_late(void)
@@ -427,7 +433,7 @@ void __init omap2430_init_early(void)
 	omap243x_clockdomains_init();
 	omap2430_hwmod_init();
 	omap_hwmod_init_postsetup();
-	omap2430_clk_init();
+	omap_clk_init = omap2430_clk_init;
 }
 
 void __init omap2430_init_late(void)
@@ -462,7 +468,7 @@ void __init omap3_init_early(void)
 	omap3xxx_clockdomains_init();
 	omap3xxx_hwmod_init();
 	omap_hwmod_init_postsetup();
-	omap3xxx_clk_init();
+	omap_clk_init = omap3xxx_clk_init;
 }
 
 void __init omap3430_init_early(void)
@@ -500,7 +506,7 @@ void __init ti81xx_init_early(void)
 	omap3xxx_clockdomains_init();
 	omap3xxx_hwmod_init();
 	omap_hwmod_init_postsetup();
-	omap3xxx_clk_init();
+	omap_clk_init = omap3xxx_clk_init;
 }
 
 void __init omap3_init_late(void)
@@ -568,7 +574,7 @@ void __init am33xx_init_early(void)
 	am33xx_clockdomains_init();
 	am33xx_hwmod_init();
 	omap_hwmod_init_postsetup();
-	am33xx_clk_init();
+	omap_clk_init = am33xx_clk_init;
 }
 #endif
 
@@ -593,7 +599,7 @@ void __init omap4430_init_early(void)
 	omap44xx_clockdomains_init();
 	omap44xx_hwmod_init();
 	omap_hwmod_init_postsetup();
-	omap4xxx_clk_init();
+	omap_clk_init = omap4xxx_clk_init;
 }
 
 void __init omap4430_init_late(void)
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index c2c798c08c2..a202a478510 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -1368,7 +1368,9 @@ static void _enable_sysc(struct omap_hwmod *oh)
 	}
 
 	if (sf & SYSC_HAS_MIDLEMODE) {
-		if (oh->flags & HWMOD_SWSUP_MSTANDBY) {
+		if (oh->flags & HWMOD_FORCE_MSTANDBY) {
+			idlemode = HWMOD_IDLEMODE_FORCE;
+		} else if (oh->flags & HWMOD_SWSUP_MSTANDBY) {
 			idlemode = HWMOD_IDLEMODE_NO;
 		} else {
 			if (sf & SYSC_HAS_ENAWAKEUP)
@@ -1440,7 +1442,8 @@ static void _idle_sysc(struct omap_hwmod *oh)
 	}
 
 	if (sf & SYSC_HAS_MIDLEMODE) {
-		if (oh->flags & HWMOD_SWSUP_MSTANDBY) {
+		if ((oh->flags & HWMOD_SWSUP_MSTANDBY) ||
+		    (oh->flags & HWMOD_FORCE_MSTANDBY)) {
 			idlemode = HWMOD_IDLEMODE_FORCE;
 		} else {
 			if (sf & SYSC_HAS_ENAWAKEUP)
diff --git a/arch/arm/mach-omap2/omap_hwmod.h b/arch/arm/mach-omap2/omap_hwmod.h
index d43d9b608ed..d5dc935f606 100644
--- a/arch/arm/mach-omap2/omap_hwmod.h
+++ b/arch/arm/mach-omap2/omap_hwmod.h
@@ -427,8 +427,8 @@ struct omap_hwmod_omap4_prcm {
  *
  * HWMOD_SWSUP_SIDLE: omap_hwmod code should manually bring module in and out
  *     of idle, rather than relying on module smart-idle
- * HWMOD_SWSUP_MSTDBY: omap_hwmod code should manually bring module in and out
- *     of standby, rather than relying on module smart-standby
+ * HWMOD_SWSUP_MSTANDBY: omap_hwmod code should manually bring module in and
+ *     out of standby, rather than relying on module smart-standby
  * HWMOD_INIT_NO_RESET: don't reset this module at boot - important for
  *     SDRAM controller, etc. XXX probably belongs outside the main hwmod file
  *     XXX Should be HWMOD_SETUP_NO_RESET
@@ -459,6 +459,10 @@ struct omap_hwmod_omap4_prcm {
  *     correctly, or this is being abused to deal with some PM latency
  *     issues -- but we're currently suffering from a shortage of
  *     folks who are able to track these issues down properly.
+ * HWMOD_FORCE_MSTANDBY: Always keep MIDLEMODE bits cleared so that device
+ *     is kept in force-standby mode. Failing to do so causes PM problems
+ *     with musb on OMAP3630 at least. Note that musb has a dedicated register
+ *     to control MSTANDBY signal when MIDLEMODE is set to force-standby.
  */
 #define HWMOD_SWSUP_SIDLE			(1 << 0)
 #define HWMOD_SWSUP_MSTANDBY			(1 << 1)
@@ -471,6 +475,7 @@ struct omap_hwmod_omap4_prcm {
 #define HWMOD_16BIT_REG				(1 << 8)
 #define HWMOD_EXT_OPT_MAIN_CLK			(1 << 9)
 #define HWMOD_BLOCK_WFI				(1 << 10)
+#define HWMOD_FORCE_MSTANDBY			(1 << 11)
 
 /*
  * omap_hwmod._int_flags definitions
diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
index ac7e03ec952..5112d04e7b7 100644
--- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
@@ -1707,9 +1707,14 @@ static struct omap_hwmod omap3xxx_usbhsotg_hwmod = {
 	 * Erratum ID: i479  idle_req / idle_ack mechanism potentially
 	 * broken when autoidle is enabled
 	 * workaround is to disable the autoidle bit at module level.
+	 *
+	 * Enabling the device in any other MIDLEMODE setting but force-idle
+	 * causes core_pwrdm not enter idle states at least on OMAP3630.
+	 * Note that musb has OTG_FORCESTDBY register that controls MSTANDBY
+	 * signal when MIDLEMODE is set to force-idle.
 	 */
 	.flags		= HWMOD_NO_OCP_AUTOIDLE | HWMOD_SWSUP_SIDLE
-				| HWMOD_SWSUP_MSTANDBY,
+				| HWMOD_FORCE_MSTANDBY,
 };
 
 /* usb_otg_hs */
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index 0e47d2e1687..9e0576569e0 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -2714,6 +2714,10 @@ static struct omap_ocp2scp_dev ocp2scp_dev_attr[] = {
 	{ }
 };
 
+static struct omap_hwmod_opt_clk ocp2scp_usb_phy_opt_clks[] = {
+	{ .role = "48mhz", .clk = "ocp2scp_usb_phy_phy_48m" },
+};
+
 /* ocp2scp_usb_phy */
 static struct omap_hwmod omap44xx_ocp2scp_usb_phy_hwmod = {
 	.name		= "ocp2scp_usb_phy",
@@ -2728,6 +2732,8 @@ static struct omap_hwmod omap44xx_ocp2scp_usb_phy_hwmod = {
 		},
 	},
 	.dev_attr	= ocp2scp_dev_attr,
+	.opt_clks	= ocp2scp_usb_phy_opt_clks,
+	.opt_clks_cnt	= ARRAY_SIZE(ocp2scp_usb_phy_opt_clks),
 };
 
 /*
diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
index 2bdd4cf17a8..f62b509ed08 100644
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -547,6 +547,8 @@ static inline void __init realtime_counter_init(void)
 			       clksrc_nr, clksrc_src)			\
 void __init omap##name##_gptimer_timer_init(void)			\
 {									\
+	if (omap_clk_init)						\
+		omap_clk_init();					\
 	omap_dmtimer_init();						\
 	omap2_gp_clockevent_init((clkev_nr), clkev_src, clkev_prop);	\
 	omap2_gptimer_clocksource_init((clksrc_nr), clksrc_src);	\
@@ -556,6 +558,8 @@ void __init omap##name##_gptimer_timer_init(void)			\
 				clksrc_nr, clksrc_src)			\
 void __init omap##name##_sync32k_timer_init(void)		\
 {									\
+	if (omap_clk_init)						\
+		omap_clk_init();					\
 	omap_dmtimer_init();						\
 	omap2_gp_clockevent_init((clkev_nr), clkev_src, clkev_prop);	\
 	/* Enable the use of clocksource="gp_timer" kernel parameter */	\
diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c
index 051b62c2710..7f2cb6c5e2c 100644
--- a/arch/arm/mach-ux500/board-mop500-sdi.c
+++ b/arch/arm/mach-ux500/board-mop500-sdi.c
@@ -81,7 +81,6 @@ static struct stedma40_chan_cfg mop500_sdi0_dma_cfg_tx = {
 #endif
 
 struct mmci_platform_data mop500_sdi0_data = {
-	.ios_handler	= mop500_sdi0_ios_handler,
 	.ocr_mask	= MMC_VDD_29_30,
 	.f_max		= 50000000,
 	.capabilities	= MMC_CAP_4_BIT_DATA |
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index b03457881c4..87d2d7b38ce 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -12,6 +12,7 @@
 #include <linux/init.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
+#include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/i2c.h>
 #include <linux/platform_data/i2c-nomadik.h>
@@ -439,6 +440,15 @@ static void mop500_prox_deactivate(struct device *dev)
 	regulator_put(prox_regulator);
 }
 
+void mop500_snowball_ethernet_clock_enable(void)
+{
+	struct clk *clk;
+
+	clk = clk_get_sys("fsmc", NULL);
+	if (!IS_ERR(clk))
+		clk_prepare_enable(clk);
+}
+
 static struct cryp_platform_data u8500_cryp1_platform_data = {
 		.mem_to_engine = {
 				.dir = STEDMA40_MEM_TO_PERIPH,
@@ -683,6 +693,8 @@ static void __init snowball_init_machine(void)
 	mop500_audio_init(parent);
 	mop500_uart_init(parent);
 
+	mop500_snowball_ethernet_clock_enable();
+
 	/* This board has full regulator constraints */
 	regulator_has_full_constraints();
 }
diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h
index eaa605f5d90..d38951be70d 100644
--- a/arch/arm/mach-ux500/board-mop500.h
+++ b/arch/arm/mach-ux500/board-mop500.h
@@ -104,6 +104,7 @@ void __init mop500_pinmaps_init(void);
 void __init snowball_pinmaps_init(void);
 void __init hrefv60_pinmaps_init(void);
 void mop500_audio_init(struct device *parent);
+void mop500_snowball_ethernet_clock_enable(void);
 
 int __init mop500_uib_init(void);
 void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 19235cf7bbe..f1a58184437 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -312,9 +312,10 @@ static void __init u8500_init_machine(void)
 	/* Pinmaps must be in place before devices register */
 	if (of_machine_is_compatible("st-ericsson,mop500"))
 		mop500_pinmaps_init();
-	else if (of_machine_is_compatible("calaosystems,snowball-a9500"))
+	else if (of_machine_is_compatible("calaosystems,snowball-a9500")) {
 		snowball_pinmaps_init();
-	else if (of_machine_is_compatible("st-ericsson,hrefv60+"))
+		mop500_snowball_ethernet_clock_enable();
+	} else if (of_machine_is_compatible("st-ericsson,hrefv60+"))
 		hrefv60_pinmaps_init();
 	else if (of_machine_is_compatible("st-ericsson,ccu9540")) {}
 		/* TODO: Add pinmaps for ccu9540 board. */