drm/i915: precompute pipe bpp before touching the hw

The procedure has now 3 steps:

1. Compute the bpp that the plane will output, this is done in
   pipe_config_set_bpp and stored into pipe_config->pipe_bpp. Also,
   this function clamps the pipe_bpp to whatever limit the EDID of any
   connected output specifies.
2. Adjust the pipe_bpp in the encoder and crtc functions, according to
   whatever constraints there are.
3. Decide whether to use dither by comparing the stored plane bpp with
   computed pipe_bpp.

There are a few slight functional changes in this patch:
- LVDS connector are now also going through the EDID clamping. But in
  a 2nd change we now unconditionally force the lvds bpc value - this
  shouldn't matter in reality when the panel setup is consistent, but
  better safe than sorry.
- HDMI now forces the pipe_bpp to the selected value - I think that's
  what we actually want, since otherwise at least the pixelclock
  computations are wrong (I'm not sure whether the port would accept
  e.g. 10 bpc when in 12bpc mode). Contrary to the old code, we pick
  the next higher bpc value, since otherwise there's no way to make
  use of the 12 bpc mode (since the next patch will remove the 12bpc
  plane format, it doesn't exist).

Both of these changes are due to the removal of the

	pipe_bpp = min(display_bpp, plane_bpp);

statement.

Another slight change is the reworking of the dp bpc code:
- For the mode_valid callback it's sufficient to only check whether
  the mode would fit at the lowest bpc.
- The bandwidth computation code is a bit restructured: It now walks
  all available bpp values in an outer loop and the codeblock that
  computes derived values (once a good configuration is found) has been
  moved out of the for loop maze. This is prep work to allow us to
  successively fall back on bpc values, and also correctly support bpc
  values != 8 or 6.

v2: Rebased on top of Paulo Zanoni's little refactoring to use more
drm dp helper functions.

v3: Rebased on top of Jani's eDP bpp fix and Ville's limited color
range work.

v4: Remove the INTEL_MODE_DP_FORCE_6BPC #define, no longer needed.

v5: Remove intel_crtc->bpp, too, and fix up the 12bpc check in the
hdmi code. Also fixup the bpp check in intel_dp.c, it'll get reworked
in a later patch though again.

v6: Fix spelling in a comment.

v7: Debug output improvements for the bpp computation.

v8: Fixup 6bpc lvds check - dual-link and 8bpc mode are different
things!

v9: Reinstate the fix to properly ignore the firmware edp bpp ... this
was lost in a rebase.

v10: Both g4x and vlv lack 12bpc pipes, so don't enforce that we have
that. Still unsure whether this is the way to go, but at least 6bpc
for a 8bpc hdmi output seems to work.

v11: And g4x/vlv also lack 12bpc hdmi support, so only support high
depth on DP. Adjust the code.

v12: Rebased.

v13: Split out the introduction of pipe_config->dither|pipe_bpp, as
requested from Jesse Barnes.

v14: Split out the special 6BPC handling for DP, as requested by Jesse
Barnes.

Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

1 files changed, 12 insertions, 0 deletions

diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c
index 9d6ed91b443..7b6d07b6a02 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -310,6 +310,7 @@ static bool intel_lvds_compute_config(struct intel_encoder *intel_encoder,
 	struct drm_display_mode *mode = &pipe_config->requested_mode;
 	struct intel_crtc *intel_crtc = lvds_encoder->base.new_crtc;
 	u32 pfit_control = 0, pfit_pgm_ratios = 0, border = 0;
+	unsigned int lvds_bpp;
 	int pipe;
 
 	/* Should never happen!! */
@@ -321,6 +322,17 @@ static bool intel_lvds_compute_config(struct intel_encoder *intel_encoder,
 	if (intel_encoder_check_is_cloned(&lvds_encoder->base))
 		return false;
 
+	if ((I915_READ(lvds_encoder->reg) & LVDS_A3_POWER_MASK) ==
+	    LVDS_A3_POWER_UP)
+		lvds_bpp = 8*3;
+	else
+		lvds_bpp = 6*3;
+
+	if (lvds_bpp != pipe_config->pipe_bpp) {
+		DRM_DEBUG_KMS("forcing display bpp (was %d) to LVDS (%d)\n",
+			      pipe_config->pipe_bpp, lvds_bpp);
+		pipe_config->pipe_bpp = lvds_bpp;
+	}
 	/*
 	 * We have timings from the BIOS for the panel, put them in
 	 * to the adjusted mode.  The CRTC will be set up for this mode,