Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
  omap2: Make OMAP2PLUS select OMAP_DM_TIMER
  OMAP4: hwmod data: Fix alignment and end of line in structurefields
  OMAP4: hwmod data: Move the DMA structures
  OMAP4: hwmod data: Move the smartreflex structures
  OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
  arm: omap: tusb6010: add name for MUSB IRQ
  arm: omap: craneboard: Add USB EHCI support
  omap2+: Initialize serial port for dynamic remuxing for n8x0
  omap2+: Add struct omap_board_data and use it for platform level serial init
  omap2+: Allow hwmod state changes to mux pads based on the state changes
  omap2+: Add support for hwmod specific muxing of devices
  omap2+: Add omap_mux_get_by_name
  OMAP2: PM: fix compile error when !CONFIG_SUSPEND
  MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
  OMAP4: Smartreflex framework extensions
  OMAP4: hwmod: Add inital data for smartreflex modules.
  OMAP4: PM: Program correct init voltages for scalable VDDs
  OMAP4: Adding voltage driver support
  OMAP4: Register voltage PMIC parameters with the voltage layer
  OMAP3: PM: Program correct init voltages for VDD1 and VDD2
  ...

Fix up trivial conflict in arch/arm/plat-omap/Kconfig

7 files changed, 93 insertions, 106 deletions

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index b33c78586bf..9d090833e24 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -39,6 +39,7 @@
 #include <linux/io.h>
 #include <linux/slab.h>
 #include <linux/i2c-omap.h>
+#include <linux/pm_runtime.h>
 
 /* I2C controller revisions */
 #define OMAP_I2C_REV_2			0x20
@@ -175,8 +176,6 @@ struct omap_i2c_dev {
 	void __iomem		*base;		/* virtual */
 	int			irq;
 	int			reg_shift;      /* bit shift for I2C register addresses */
-	struct clk		*iclk;		/* Interface clock */
-	struct clk		*fclk;		/* Functional clock */
 	struct completion	cmd_complete;
 	struct resource		*ioarea;
 	u32			latency;	/* maximum mpu wkup latency */
@@ -265,45 +264,18 @@ static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *i2c_dev, int reg)
 				(i2c_dev->regs[reg] << i2c_dev->reg_shift));
 }
 
-static int __init omap_i2c_get_clocks(struct omap_i2c_dev *dev)
+static void omap_i2c_unidle(struct omap_i2c_dev *dev)
 {
-	int ret;
+	struct platform_device *pdev;
+	struct omap_i2c_bus_platform_data *pdata;
 
-	dev->iclk = clk_get(dev->dev, "ick");
-	if (IS_ERR(dev->iclk)) {
-		ret = PTR_ERR(dev->iclk);
-		dev->iclk = NULL;
-		return ret;
-	}
+	WARN_ON(!dev->idle);
 
-	dev->fclk = clk_get(dev->dev, "fck");
-	if (IS_ERR(dev->fclk)) {
-		ret = PTR_ERR(dev->fclk);
-		if (dev->iclk != NULL) {
-			clk_put(dev->iclk);
-			dev->iclk = NULL;
-		}
-		dev->fclk = NULL;
-		return ret;
-	}
+	pdev = to_platform_device(dev->dev);
+	pdata = pdev->dev.platform_data;
 
-	return 0;
-}
+	pm_runtime_get_sync(&pdev->dev);
 
-static void omap_i2c_put_clocks(struct omap_i2c_dev *dev)
-{
-	clk_put(dev->fclk);
-	dev->fclk = NULL;
-	clk_put(dev->iclk);
-	dev->iclk = NULL;
-}
-
-static void omap_i2c_unidle(struct omap_i2c_dev *dev)
-{
-	WARN_ON(!dev->idle);
-
-	clk_enable(dev->iclk);
-	clk_enable(dev->fclk);
 	if (cpu_is_omap34xx()) {
 		omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
 		omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, dev->pscstate);
@@ -326,10 +298,15 @@ static void omap_i2c_unidle(struct omap_i2c_dev *dev)
 
 static void omap_i2c_idle(struct omap_i2c_dev *dev)
 {
+	struct platform_device *pdev;
+	struct omap_i2c_bus_platform_data *pdata;
 	u16 iv;
 
 	WARN_ON(dev->idle);
 
+	pdev = to_platform_device(dev->dev);
+	pdata = pdev->dev.platform_data;
+
 	dev->iestate = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
 	if (dev->rev >= OMAP_I2C_REV_ON_4430)
 		omap_i2c_write_reg(dev, OMAP_I2C_IRQENABLE_CLR, 1);
@@ -345,8 +322,8 @@ static void omap_i2c_idle(struct omap_i2c_dev *dev)
 		omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
 	}
 	dev->idle = 1;
-	clk_disable(dev->fclk);
-	clk_disable(dev->iclk);
+
+	pm_runtime_put_sync(&pdev->dev);
 }
 
 static int omap_i2c_init(struct omap_i2c_dev *dev)
@@ -356,6 +333,7 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
 	unsigned long fclk_rate = 12000000;
 	unsigned long timeout;
 	unsigned long internal_clk = 0;
+	struct clk *fclk;
 
 	if (dev->rev >= OMAP_I2C_REV_2) {
 		/* Disable I2C controller before soft reset */
@@ -414,7 +392,9 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
 		 * always returns 12MHz for the functional clock, we can
 		 * do this bit unconditionally.
 		 */
-		fclk_rate = clk_get_rate(dev->fclk);
+		fclk = clk_get(dev->dev, "fck");
+		fclk_rate = clk_get_rate(fclk);
+		clk_put(fclk);
 
 		/* TRM for 5912 says the I2C clock must be prescaled to be
 		 * between 7 - 12 MHz. The XOR input clock is typically
@@ -443,7 +423,9 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
 			internal_clk = 9600;
 		else
 			internal_clk = 4000;
-		fclk_rate = clk_get_rate(dev->fclk) / 1000;
+		fclk = clk_get(dev->dev, "fck");
+		fclk_rate = clk_get_rate(fclk) / 1000;
+		clk_put(fclk);
 
 		/* Compute prescaler divisor */
 		psc = fclk_rate / internal_clk;
@@ -1048,14 +1030,12 @@ omap_i2c_probe(struct platform_device *pdev)
 	else
 		dev->reg_shift = 2;
 
-	if ((r = omap_i2c_get_clocks(dev)) != 0)
-		goto err_iounmap;
-
 	if (cpu_is_omap44xx())
 		dev->regs = (u8 *) omap4_reg_map;
 	else
 		dev->regs = (u8 *) reg_map;
 
+	pm_runtime_enable(&pdev->dev);
 	omap_i2c_unidle(dev);
 
 	dev->rev = omap_i2c_read_reg(dev, OMAP_I2C_REV_REG) & 0xff;
@@ -1127,8 +1107,6 @@ err_free_irq:
 err_unuse_clocks:
 	omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
 	omap_i2c_idle(dev);
-	omap_i2c_put_clocks(dev);
-err_iounmap:
 	iounmap(dev->base);
 err_free_mem:
 	platform_set_drvdata(pdev, NULL);
@@ -1150,7 +1128,6 @@ omap_i2c_remove(struct platform_device *pdev)
 	free_irq(dev->irq, dev);
 	i2c_del_adapter(&dev->adapter);
 	omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
-	omap_i2c_put_clocks(dev);
 	iounmap(dev->base);
 	kfree(dev);
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -1162,7 +1139,7 @@ static struct platform_driver omap_i2c_driver = {
 	.probe		= omap_i2c_probe,
 	.remove		= omap_i2c_remove,
 	.driver		= {
-		.name	= "i2c_omap",
+		.name	= "omap_i2c",
 		.owner	= THIS_MODULE,
 	},
 };
@@ -1184,4 +1161,4 @@ module_exit(omap_i2c_exit_driver);
 MODULE_AUTHOR("MontaVista Software, Inc. (and others)");
 MODULE_DESCRIPTION("TI OMAP I2C bus adapter");
 MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:i2c_omap");
+MODULE_ALIAS("platform:omap_i2c");
diff --git a/drivers/input/keyboard/omap-keypad.c b/drivers/input/keyboard/omap-keypad.c
index a72e61ddca9..0e2a19cb43d 100644
--- a/drivers/input/keyboard/omap-keypad.c
+++ b/drivers/input/keyboard/omap-keypad.c
@@ -65,7 +65,6 @@ struct omap_kp {
 
 static DECLARE_TASKLET_DISABLED(kp_tasklet, omap_kp_tasklet, 0);
 
-static int *keymap;
 static unsigned int *row_gpios;
 static unsigned int *col_gpios;
 
@@ -162,20 +161,11 @@ static void omap_kp_scan_keypad(struct omap_kp *omap_kp, unsigned char *state)
 	}
 }
 
-static inline int omap_kp_find_key(int col, int row)
-{
-	int i, key;
-
-	key = KEY(col, row, 0);
-	for (i = 0; keymap[i] != 0; i++)
-		if ((keymap[i] & 0xff000000) == key)
-			return keymap[i] & 0x00ffffff;
-	return -1;
-}
-
 static void omap_kp_tasklet(unsigned long data)
 {
 	struct omap_kp *omap_kp_data = (struct omap_kp *) data;
+	unsigned short *keycodes = omap_kp_data->input->keycode;
+	unsigned int row_shift = get_count_order(omap_kp_data->cols);
 	unsigned char new_state[8], changed, key_down = 0;
 	int col, row;
 	int spurious = 0;
@@ -199,7 +189,7 @@ static void omap_kp_tasklet(unsigned long data)
 			       row, (new_state[col] & (1 << row)) ?
 			       "pressed" : "released");
 #else
-			key = omap_kp_find_key(col, row);
+			key = keycodes[MATRIX_SCAN_CODE(row, col, row_shift)];
 			if (key < 0) {
 				printk(KERN_WARNING
 				      "omap-keypad: Spurious key event %d-%d\n",
@@ -298,13 +288,18 @@ static int __devinit omap_kp_probe(struct platform_device *pdev)
 	struct input_dev *input_dev;
 	struct omap_kp_platform_data *pdata =  pdev->dev.platform_data;
 	int i, col_idx, row_idx, irq_idx, ret;
+	unsigned int row_shift, keycodemax;
 
-	if (!pdata->rows || !pdata->cols || !pdata->keymap) {
-		printk(KERN_ERR "No rows, cols or keymap from pdata\n");
+	if (!pdata->rows || !pdata->cols || !pdata->keymap_data) {
+		printk(KERN_ERR "No rows, cols or keymap_data from pdata\n");
 		return -EINVAL;
 	}
 
-	omap_kp = kzalloc(sizeof(struct omap_kp), GFP_KERNEL);
+	row_shift = get_count_order(pdata->cols);
+	keycodemax = pdata->rows << row_shift;
+
+	omap_kp = kzalloc(sizeof(struct omap_kp) +
+			keycodemax * sizeof(unsigned short), GFP_KERNEL);
 	input_dev = input_allocate_device();
 	if (!omap_kp || !input_dev) {
 		kfree(omap_kp);
@@ -320,7 +315,9 @@ static int __devinit omap_kp_probe(struct platform_device *pdev)
 	if (!cpu_is_omap24xx())
 		omap_writew(1, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
 
-	keymap = pdata->keymap;
+	input_dev->keycode      = &omap_kp[1];
+	input_dev->keycodesize  = sizeof(unsigned short);
+	input_dev->keycodemax   = keycodemax;
 
 	if (pdata->rep)
 		__set_bit(EV_REP, input_dev->evbit);
@@ -374,8 +371,8 @@ static int __devinit omap_kp_probe(struct platform_device *pdev)
 
 	/* setup input device */
 	__set_bit(EV_KEY, input_dev->evbit);
-	for (i = 0; keymap[i] != 0; i++)
-		__set_bit(keymap[i] & KEY_MAX, input_dev->keybit);
+	matrix_keypad_build_keymap(pdata->keymap_data, row_shift,
+			input_dev->keycode, input_dev->keybit);
 	input_dev->name = "omap-keypad";
 	input_dev->phys = "omap-keypad/input0";
 	input_dev->dev.parent = &pdev->dev;
@@ -416,7 +413,7 @@ static int __devinit omap_kp_probe(struct platform_device *pdev)
 	return 0;
 err5:
 	for (i = irq_idx - 1; i >=0; i--)
-		free_irq(row_gpios[i], 0);
+		free_irq(row_gpios[i], NULL);
 err4:
 	input_unregister_device(omap_kp->input);
 	input_dev = NULL;
@@ -447,11 +444,11 @@ static int __devexit omap_kp_remove(struct platform_device *pdev)
 			gpio_free(col_gpios[i]);
 		for (i = 0; i < omap_kp->rows; i++) {
 			gpio_free(row_gpios[i]);
-			free_irq(gpio_to_irq(row_gpios[i]), 0);
+			free_irq(gpio_to_irq(row_gpios[i]), NULL);
 		}
 	} else {
 		omap_writew(1, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
-		free_irq(omap_kp->irq, 0);
+		free_irq(omap_kp->irq, NULL);
 	}
 
 	del_timer_sync(&omap_kp->timer);
diff --git a/drivers/input/serio/Kconfig b/drivers/input/serio/Kconfig
index 6256233d2bf..bcb1fdedb59 100644
--- a/drivers/input/serio/Kconfig
+++ b/drivers/input/serio/Kconfig
@@ -214,7 +214,6 @@ config SERIO_AMS_DELTA
 	tristate "Amstrad Delta (E3) mailboard support"
 	depends on MACH_AMS_DELTA
 	default y
-	select AMS_DELTA_FIQ
 	---help---
 	  Say Y here if you have an E3 and want to use its mailboard,
 	  or any standard AT keyboard connected to the mailboard port.
diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c
index 9f322f1a7f2..d0894ca7798 100644
--- a/drivers/mtd/onenand/omap2.c
+++ b/drivers/mtd/onenand/omap2.c
@@ -721,6 +721,9 @@ static int __devinit omap2_onenand_probe(struct platform_device *pdev)
 	case 3:
 		c->freq = 83;
 		break;
+	case 4:
+		c->freq = 104;
+		break;
 	}
 
 #ifdef CONFIG_MTD_PARTITIONS
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 09a550860dc..ee74c934de8 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -653,13 +653,13 @@ static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
 {
 	if (p->capabilities & UART_CAP_SLEEP) {
 		if (p->capabilities & UART_CAP_EFR) {
-			serial_outp(p, UART_LCR, 0xBF);
+			serial_outp(p, UART_LCR, UART_LCR_CONF_MODE_B);
 			serial_outp(p, UART_EFR, UART_EFR_ECB);
 			serial_outp(p, UART_LCR, 0);
 		}
 		serial_outp(p, UART_IER, sleep ? UART_IERX_SLEEP : 0);
 		if (p->capabilities & UART_CAP_EFR) {
-			serial_outp(p, UART_LCR, 0xBF);
+			serial_outp(p, UART_LCR, UART_LCR_CONF_MODE_B);
 			serial_outp(p, UART_EFR, 0);
 			serial_outp(p, UART_LCR, 0);
 		}
@@ -752,7 +752,7 @@ static int size_fifo(struct uart_8250_port *up)
 	serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
 		    UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
 	serial_outp(up, UART_MCR, UART_MCR_LOOP);
-	serial_outp(up, UART_LCR, UART_LCR_DLAB);
+	serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_A);
 	old_dl = serial_dl_read(up);
 	serial_dl_write(up, 0x0001);
 	serial_outp(up, UART_LCR, 0x03);
@@ -764,7 +764,7 @@ static int size_fifo(struct uart_8250_port *up)
 		serial_inp(up, UART_RX);
 	serial_outp(up, UART_FCR, old_fcr);
 	serial_outp(up, UART_MCR, old_mcr);
-	serial_outp(up, UART_LCR, UART_LCR_DLAB);
+	serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_A);
 	serial_dl_write(up, old_dl);
 	serial_outp(up, UART_LCR, old_lcr);
 
@@ -782,7 +782,7 @@ static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
 	unsigned int id;
 
 	old_lcr = serial_inp(p, UART_LCR);
-	serial_outp(p, UART_LCR, UART_LCR_DLAB);
+	serial_outp(p, UART_LCR, UART_LCR_CONF_MODE_A);
 
 	old_dll = serial_inp(p, UART_DLL);
 	old_dlm = serial_inp(p, UART_DLM);
@@ -836,7 +836,7 @@ static void autoconfig_has_efr(struct uart_8250_port *up)
 	 * recommended for new designs).
 	 */
 	up->acr = 0;
-	serial_out(up, UART_LCR, 0xBF);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	serial_out(up, UART_EFR, UART_EFR_ECB);
 	serial_out(up, UART_LCR, 0x00);
 	id1 = serial_icr_read(up, UART_ID1);
@@ -945,7 +945,7 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 	 * Check for presence of the EFR when DLAB is set.
 	 * Only ST16C650V1 UARTs pass this test.
 	 */
-	serial_outp(up, UART_LCR, UART_LCR_DLAB);
+	serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_A);
 	if (serial_in(up, UART_EFR) == 0) {
 		serial_outp(up, UART_EFR, 0xA8);
 		if (serial_in(up, UART_EFR) != 0) {
@@ -963,7 +963,7 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 	 * Maybe it requires 0xbf to be written to the LCR.
 	 * (other ST16C650V2 UARTs, TI16C752A, etc)
 	 */
-	serial_outp(up, UART_LCR, 0xBF);
+	serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) {
 		DEBUG_AUTOCONF("EFRv2 ");
 		autoconfig_has_efr(up);
@@ -1024,7 +1024,7 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 	serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
 	status1 = serial_in(up, UART_IIR) >> 5;
 	serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
-	serial_outp(up, UART_LCR, UART_LCR_DLAB);
+	serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_A);
 	serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
 	status2 = serial_in(up, UART_IIR) >> 5;
 	serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
@@ -1183,7 +1183,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
 	 * We also initialise the EFR (if any) to zero for later.  The
 	 * EFR occupies the same register location as the FCR and IIR.
 	 */
-	serial_outp(up, UART_LCR, 0xBF);
+	serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	serial_outp(up, UART_EFR, 0);
 	serial_outp(up, UART_LCR, 0);
 
@@ -1952,7 +1952,7 @@ static int serial8250_startup(struct uart_port *port)
 	if (up->port.type == PORT_16C950) {
 		/* Wake up and initialize UART */
 		up->acr = 0;
-		serial_outp(up, UART_LCR, 0xBF);
+		serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_B);
 		serial_outp(up, UART_EFR, UART_EFR_ECB);
 		serial_outp(up, UART_IER, 0);
 		serial_outp(up, UART_LCR, 0);
@@ -2002,7 +2002,7 @@ static int serial8250_startup(struct uart_port *port)
 	if (up->port.type == PORT_16850) {
 		unsigned char fctr;
 
-		serial_outp(up, UART_LCR, 0xbf);
+		serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_B);
 
 		fctr = serial_inp(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX);
 		serial_outp(up, UART_FCTR, fctr | UART_FCTR_TRGD | UART_FCTR_RX);
@@ -2363,7 +2363,7 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
 		if (termios->c_cflag & CRTSCTS)
 			efr |= UART_EFR_CTS;
 
-		serial_outp(up, UART_LCR, 0xBF);
+		serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_B);
 		serial_outp(up, UART_EFR, efr);
 	}
 
diff --git a/drivers/serial/omap-serial.c b/drivers/serial/omap-serial.c
index 14365f72b66..1201eff1831 100644
--- a/drivers/serial/omap-serial.c
+++ b/drivers/serial/omap-serial.c
@@ -570,7 +570,7 @@ serial_omap_configure_xonxoff
 	unsigned char efr = 0;
 
 	up->lcr = serial_in(up, UART_LCR);
-	serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	up->efr = serial_in(up, UART_EFR);
 	serial_out(up, UART_EFR, up->efr & ~UART_EFR_ECB);
 
@@ -598,7 +598,7 @@ serial_omap_configure_xonxoff
 		efr |= OMAP_UART_SW_RX;
 
 	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
-	serial_out(up, UART_LCR, UART_LCR_DLAB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
 
 	up->mcr = serial_in(up, UART_MCR);
 
@@ -612,14 +612,14 @@ serial_omap_configure_xonxoff
 		up->mcr |= UART_MCR_XONANY;
 
 	serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
-	serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
 	/* Enable special char function UARTi.EFR_REG[5] and
 	 * load the new software flow control mode IXON or IXOFF
 	 * and restore the UARTi.EFR_REG[4] ENHANCED_EN value.
 	 */
 	serial_out(up, UART_EFR, efr | UART_EFR_SCD);
-	serial_out(up, UART_LCR, UART_LCR_DLAB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
 
 	serial_out(up, UART_MCR, up->mcr & ~UART_MCR_TCRTLR);
 	serial_out(up, UART_LCR, up->lcr);
@@ -724,22 +724,22 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
 	 * baud clock is not running
 	 * DLL_REG and DLH_REG set to 0.
 	 */
-	serial_out(up, UART_LCR, UART_LCR_DLAB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
 	serial_out(up, UART_DLL, 0);
 	serial_out(up, UART_DLM, 0);
 	serial_out(up, UART_LCR, 0);
 
-	serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 
 	up->efr = serial_in(up, UART_EFR);
 	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
 
-	serial_out(up, UART_LCR, UART_LCR_DLAB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
 	up->mcr = serial_in(up, UART_MCR);
 	serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
 	/* FIFO ENABLE, DMA MODE */
 	serial_out(up, UART_FCR, up->fcr);
-	serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 
 	if (up->use_dma) {
 		serial_out(up, UART_TI752_TLR, 0);
@@ -748,52 +748,52 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
 	}
 
 	serial_out(up, UART_EFR, up->efr);
-	serial_out(up, UART_LCR, UART_LCR_DLAB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
 	serial_out(up, UART_MCR, up->mcr);
 
 	/* Protocol, Baud Rate, and Interrupt Settings */
 
-	serial_out(up, UART_OMAP_MDR1, OMAP_MDR1_DISABLE);
-	serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+	serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 
 	up->efr = serial_in(up, UART_EFR);
 	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
 
 	serial_out(up, UART_LCR, 0);
 	serial_out(up, UART_IER, 0);
-	serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 
 	serial_out(up, UART_DLL, quot & 0xff);          /* LS of divisor */
 	serial_out(up, UART_DLM, quot >> 8);            /* MS of divisor */
 
 	serial_out(up, UART_LCR, 0);
 	serial_out(up, UART_IER, up->ier);
-	serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 
 	serial_out(up, UART_EFR, up->efr);
 	serial_out(up, UART_LCR, cval);
 
 	if (baud > 230400 && baud != 3000000)
-		serial_out(up, UART_OMAP_MDR1, OMAP_MDR1_MODE13X);
+		serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_13X_MODE);
 	else
-		serial_out(up, UART_OMAP_MDR1, OMAP_MDR1_MODE16X);
+		serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_16X_MODE);
 
 	/* Hardware Flow Control Configuration */
 
 	if (termios->c_cflag & CRTSCTS) {
 		efr |= (UART_EFR_CTS | UART_EFR_RTS);
-		serial_out(up, UART_LCR, UART_LCR_DLAB);
+		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
 
 		up->mcr = serial_in(up, UART_MCR);
 		serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
 
-		serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 		up->efr = serial_in(up, UART_EFR);
 		serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
 
 		serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
 		serial_out(up, UART_EFR, efr); /* Enable AUTORTS and AUTOCTS */
-		serial_out(up, UART_LCR, UART_LCR_DLAB);
+		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
 		serial_out(up, UART_MCR, up->mcr | UART_MCR_RTS);
 		serial_out(up, UART_LCR, cval);
 	}
@@ -815,13 +815,13 @@ serial_omap_pm(struct uart_port *port, unsigned int state,
 	unsigned char efr;
 
 	dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->pdev->id);
-	serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	efr = serial_in(up, UART_EFR);
 	serial_out(up, UART_EFR, efr | UART_EFR_ECB);
 	serial_out(up, UART_LCR, 0);
 
 	serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
-	serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	serial_out(up, UART_EFR, efr);
 	serial_out(up, UART_LCR, 0);
 	/* Enable module level wake up */
diff --git a/drivers/staging/tidspbridge/core/_tiomap.h b/drivers/staging/tidspbridge/core/_tiomap.h
index 1c1f157e167..1159a500f49 100644
--- a/drivers/staging/tidspbridge/core/_tiomap.h
+++ b/drivers/staging/tidspbridge/core/_tiomap.h
@@ -19,8 +19,19 @@
 #ifndef _TIOMAP_
 #define _TIOMAP_
 
-#include <plat/powerdomain.h>
-#include <plat/clockdomain.h>
+/*
+ * XXX These powerdomain.h/clockdomain.h includes are wrong and should
+ * be removed.  No driver should call pwrdm_* or clkdm_* functions
+ * directly; they should rely on OMAP core code to do this.
+ */
+#include <mach-omap2/powerdomain.h>
+#include <mach-omap2/clockdomain.h>
+/*
+ * XXX These mach-omap2/ includes are wrong and should be removed.  No
+ * driver should read or write to PRM/CM registers directly; they
+ * should rely on OMAP core code to do this.
+ */
+#include <mach-omap2/cm2xxx_3xxx.h>
 #include <mach-omap2/prm-regbits-34xx.h>
 #include <mach-omap2/cm-regbits-34xx.h>
 #include <dspbridge/devdefs.h>