diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
6 files changed, 90 insertions, 35 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt new file mode 100644 index 00000000000..e466598105f --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt @@ -0,0 +1,26 @@ +Aeroflex Gaisler GRGPIO General Purpose I/O cores. + +The GRGPIO GPIO core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the GRGPIO core, a Leon SPARC system, +these properties are built from information in the AMBA plug&play. + +Required properties: + +- name : Should be "GAISLER_GPIO" or "01_01a" + +- reg : Address and length of the register set for the device + +- interrupts : Interrupt numbers for this device + +Optional properties: + +- nbits : The number of gpio lines. If not present driver assumes 32 lines. + +- irqmap : An array with an index for each gpio line. An index is either a valid + index into the interrupts property array, or 0xffffffff that indicates + no irq for that line. Driver provides no interrupt support if not + present. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt new file mode 100644 index 00000000000..629d0ef1730 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt @@ -0,0 +1,47 @@ +Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for +8-/16-bit I/O expander with serial interface (I2C/SPI) + +Required properties: +- compatible : Should be + - "mcp,mcp23s08" for 8 GPIO SPI version + - "mcp,mcp23s17" for 16 GPIO SPI version + - "mcp,mcp23008" for 8 GPIO I2C version or + - "mcp,mcp23017" for 16 GPIO I2C version of the chip +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify flags. Flags are currently unused. +- gpio-controller : Marks the device node as a GPIO controller. +- reg : For an address on its bus. I2C uses this a the I2C address of the chip. + SPI uses this to specify the chipselect line which the chip is + connected to. The driver and the SPI variant of the chip support + multiple chips on the same chipselect. Have a look at + mcp,spi-present-mask below. + +Required device specific properties (only for SPI chips): +- mcp,spi-present-mask : This is a present flag, that makes only sense for SPI + chips - as the name suggests. Multiple SPI chips can share the same + SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a + chip connected with the corresponding spi address set. For example if + you have a chip with address 3 connected, you have to set bit3 to 1, + which is 0x08. mcp23s08 chip variant only supports bits 0-3. It is not + possible to mix mcp23s08 and mcp23s17 on the same chipselect. Set at + least one bit to 1 for SPI chips. +- spi-max-frequency = The maximum frequency this chip is able to handle + +Example I2C: +gpiom1: gpio@20 { + compatible = "mcp,mcp23017"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; +}; + +Example SPI: +gpiom1: gpio@0 { + compatible = "mcp,mcp23s17"; + gpio-controller; + #gpio-cells = <2>; + spi-present-mask = <0x01>; + reg = <0>; + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/Documentation/devicetree/bindings/gpio/gpio-omap.txt index bff51a2fee1..8d950522e7f 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-omap.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-omap.txt @@ -5,12 +5,12 @@ Required properties: - "ti,omap2-gpio" for OMAP2 controllers - "ti,omap3-gpio" for OMAP3 controllers - "ti,omap4-gpio" for OMAP4 controllers +- gpio-controller : Marks the device node as a GPIO controller. - #gpio-cells : Should be two. - first cell is the pin number - second cell is used to specify optional parameters (unused) -- gpio-controller : Marks the device node as a GPIO controller. +- interrupt-controller: Mark the device node as an interrupt controller. - #interrupt-cells : Should be 2. -- interrupt-controller: Mark the device node as an interrupt controller The first cell is the GPIO number. The second cell is used to specify flags: bits[3:0] trigger type and level flags: @@ -20,8 +20,11 @@ Required properties: 8 = active low level-sensitive. OMAP specific properties: -- ti,hwmods: Name of the hwmod associated to the GPIO: - "gpio<X>", <X> being the 1-based instance number from the HW spec +- ti,hwmods: Name of the hwmod associated to the GPIO: + "gpio<X>", <X> being the 1-based instance number + from the HW spec. +- ti,gpio-always-on: Indicates if a GPIO bank is always powered and + so will never lose its logic state. Example: @@ -29,8 +32,8 @@ Example: gpio4: gpio4 { compatible = "ti,omap4-gpio"; ti,hwmods = "gpio4"; - #gpio-cells = <2>; gpio-controller; - #interrupt-cells = <2>; + #gpio-cells = <2>; interrupt-controller; + #interrupt-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt b/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt deleted file mode 100644 index f4dc5233167..00000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt +++ /dev/null @@ -1,24 +0,0 @@ -VIA/Wondermedia VT8500 GPIO Controller ------------------------------------------------------ - -Required properties: -- compatible : "via,vt8500-gpio", "wm,wm8505-gpio" - or "wm,wm8650-gpio" depending on your SoC -- reg : Should contain 1 register range (address and length) -- #gpio-cells : should be <3>. - 1) bank - 2) pin number - 3) flags - should be 0 - -Example: - - gpio: gpio-controller@d8110000 { - compatible = "via,vt8500-gpio"; - gpio-controller; - reg = <0xd8110000 0x10000>; - #gpio-cells = <3>; - }; - - vibrate { - gpios = <&gpio 0 1 0>; /* Bank 0, Pin 1, No flags */ - }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index a33628759d3..d933af37069 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -98,7 +98,7 @@ announce the pinrange to the pin ctrl subsystem. For example, compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; reg = <0x1460 0x18>; gpio-controller; - gpio-ranges = <&pinctrl1 20 10>, <&pinctrl2 50 20>; + gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>; } @@ -107,8 +107,8 @@ where, Next values specify the base pin and number of pins for the range handled by 'qe_pio_e' gpio. In the given example from base pin 20 to - pin 29 under pinctrl1 and pin 50 to pin 69 under pinctrl2 is handled - by this gpio controller. + pin 29 under pinctrl1 with gpio offset 0 and pin 50 to pin 69 under + pinctrl2 with gpio offset 10 is handled by this gpio controller. The pinctrl node must have "#gpio-range-cells" property to show number of arguments to pass with phandle from gpio controllers node. diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index e13787498bc..9b3f1d4a88d 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -1,7 +1,10 @@ * Marvell PXA GPIO controller Required properties: -- compatible : Should be "mrvl,pxa-gpio" or "mrvl,mmp-gpio" +- compatible : Should be "intel,pxa25x-gpio", "intel,pxa26x-gpio", + "intel,pxa27x-gpio", "intel,pxa3xx-gpio", + "marvell,pxa93x-gpio", "marvell,mmp-gpio" or + "marvell,mmp2-gpio". - reg : Address and length of the register set for the device - interrupts : Should be the port interrupt shared by all gpio pins. There're three gpio interrupts in arch-pxa, and they're gpio0, @@ -18,7 +21,7 @@ Required properties: Example: gpio: gpio@d4019000 { - compatible = "mrvl,mmp-gpio"; + compatible = "marvell,mmp-gpio"; reg = <0xd4019000 0x1000>; interrupts = <49>; interrupt-name = "gpio_mux"; |