diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc')
5 files changed, 87 insertions, 35 deletions
diff --git a/Documentation/devicetree/bindings/mmc/davinci_mmc.txt b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt new file mode 100644 index 00000000000..e5a0140b238 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt @@ -0,0 +1,33 @@ +* TI Highspeed MMC host controller for DaVinci + +The Highspeed MMC Host Controller on TI DaVinci family +provides an interface for MMC, SD and SDIO types of memory cards. + +This file documents the properties used by the davinci_mmc driver. + +Required properties: +- compatible: + Should be "ti,da830-mmc": for da830, da850, dm365 + Should be "ti,dm355-mmc": for dm355, dm644x + +Optional properties: +- bus-width: Number of data lines, can be <1>, <4>, or <8>, default <1> +- max-frequency: Maximum operating clock frequency, default 25MHz. +- dmas: List of DMA specifiers with the controller specific format + as described in the generic DMA client binding. A tx and rx + specifier is required. +- dma-names: RX and TX DMA request names. These strings correspond + 1:1 with the DMA specifiers listed in dmas. + +Example: +mmc0: mmc@1c40000 { + compatible = "ti,da830-mmc", + reg = <0x40000 0x1000>; + interrupts = <16>; + status = "okay"; + bus-width = <4>; + max-frequency = <50000000>; + dmas = <&edma 16 + &edma 17>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt new file mode 100644 index 00000000000..db442355cd2 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt @@ -0,0 +1,24 @@ +* Freescale Secure Digital Host Controller for i.MX2/3 series + +This file documents differences to the properties defined in mmc.txt. + +Required properties: +- compatible : Should be "fsl,<chip>-mmc", chip can be imx21 or imx31 + +Optional properties: +- dmas: One DMA phandle with arguments as defined by the devicetree bindings + of the used DMA controller. +- dma-names: Has to be "rx-tx". + +Example: + +sdhci1: sdhci@10014000 { + compatible = "fsl,imx27-mmc", "fsl,imx21-mmc"; + reg = <0x10014000 0x1000>; + interrupts = <11>; + dmas = <&dma 7>; + dma-names = "rx-tx"; + bus-width = <4>; + cd-gpios = <&gpio3 29>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt index 54949f6faed..515addc2007 100644 --- a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt @@ -9,15 +9,19 @@ and the properties used by the mxsmmc driver. Required properties: - compatible: Should be "fsl,<chip>-mmc". The supported chips include imx23 and imx28. -- interrupts: Should contain ERROR and DMA interrupts -- fsl,ssp-dma-channel: APBH DMA channel for the SSP +- interrupts: Should contain ERROR interrupt number +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and SSP DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". Examples: ssp0: ssp@80010000 { compatible = "fsl,imx28-mmc"; reg = <0x80010000 2000>; - interrupts = <96 82>; - fsl,ssp-dma-channel = <0>; + interrupts = <96>; + dmas = <&dma_apbh 0>; + dma-names = "rx-tx"; bus-width = <8>; }; diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 3b3a1ee055f..328e990d254 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -5,13 +5,6 @@ MMC, SD and eMMC storage mediums. This file documents differences between the core mmc properties described by mmc.txt and the properties used by the Samsung implmentation of the SDHCI controller. -Note: The mmc core bindings documentation states that if none of the core -card-detect bindings are used, then the standard sdhci card detect mechanism -is used. The Samsung's SDHCI controller bindings extends this as listed below. - -[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the - "Optional Board Specific Properties" section below. - Required SoC Specific Properties: - compatible: should be one of the following - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci @@ -20,18 +13,8 @@ Required SoC Specific Properties: controller. Required Board Specific Properties: -- Samsung GPIO variant (will be completely replaced by pinctrl): - - gpios: Should specify the gpios used for clock, command and data lines. The - gpio specifier format depends on the gpio controller. -- Pinctrl variant (preferred if available): - - pinctrl-0: Should specify pin control groups used for this controller. - - pinctrl-names: Should contain only one value - "default". - -Optional Board Specific Properties: -- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed - through a pinmux to the card-detect pin of the card slot. This property - should be used only if none of the mmc core card-detect properties are - used. Only for Samsung GPIO variant. +- pinctrl-0: Should specify pin control groups used for this controller. +- pinctrl-names: Should contain only one value - "default". Example: sdhci@12530000 { @@ -39,19 +22,9 @@ Example: reg = <0x12530000 0x100>; interrupts = <0 75 0>; bus-width = <4>; - cd-gpios = <&gpk2 2 2 3 3>; - - /* Samsung GPIO variant */ - gpios = <&gpk2 0 2 0 3>, /* clock line */ - <&gpk2 1 2 0 3>, /* command line */ - <&gpk2 3 2 3 3>, /* data line 0 */ - <&gpk2 4 2 3 3>, /* data line 1 */ - <&gpk2 5 2 3 3>, /* data line 2 */ - <&gpk2 6 2 3 3>; /* data line 3 */ - - /* Pinctrl variant */ - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>; + cd-gpios = <&gpk2 2 0>; pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>; }; Note: This example shows both SoC specific and board specific properties diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sirf.txt b/Documentation/devicetree/bindings/mmc/sdhci-sirf.txt new file mode 100644 index 00000000000..dd6ed464bcb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-sirf.txt @@ -0,0 +1,18 @@ +* SiRFprimII/marco/atlas6 SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-sirf driver. + +Required properties: +- compatible: sirf,prima2-sdhc + +Optional properties: +- cd-gpios: card detect gpio, with zero flags. + +Example: + + sd0: sdhci@56000000 { + compatible = "sirf,prima2-sdhc"; + reg = <0xcd000000 0x100000>; + cd-gpios = <&gpio 6 0>; + }; |