diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator')
5 files changed, 311 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt index 357758cb6e9..758eae24082 100644 --- a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -9,6 +9,11 @@ Required properties: - anatop-min-voltage: Minimum voltage of this regulator - anatop-max-voltage: Maximum voltage of this regulator +Optional properties: +- anatop-delay-reg-offset: Anatop MFD step time register offset +- anatop-delay-bit-shift: Bit shift for the step time register +- anatop-delay-bit-width: Number of bits used in the step time register + Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. @@ -23,6 +28,9 @@ Example: anatop-reg-offset = <0x140>; anatop-vol-bit-shift = <9>; anatop-vol-bit-width = <5>; + anatop-delay-reg-offset = <0x170>; + anatop-delay-bit-shift = <24>; + anatop-delay-bit-width = <2>; anatop-min-bit-val = <1>; anatop-min-voltage = <725000>; anatop-max-voltage = <1300000>; diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt new file mode 100644 index 00000000000..a35ff99003a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt @@ -0,0 +1,152 @@ +* Samsung S5M8767 Voltage and Current Regulator + +The Samsung S5M8767 is a multi-function device which includes volatage and +current regulators, rtc, charger controller and other sub-blocks. It is +interfaced to the host controller using a i2c interface. Each sub-block is +addressed by the host system using different i2c slave address. This document +describes the bindings for 'pmic' sub-block of s5m8767. + +Required properties: +- compatible: Should be "samsung,s5m8767-pmic". +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck3 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck4 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used + for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. + +[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s5m8767 are delivered to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for 'irq1' interrupt. + - Second interrupt specifier is for 'alert' interrupt. +- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. +- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. +- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: + +- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + +- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + +Regulators: The regulators of s5m8767 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE_1.0V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + }; +The above regulator entries are defined in regulator bindings documentation +except op_mode description. + - op_mode: describes the different operating modes of the LDO's with + power mode change in SOC. The different possible values are, + 0 - always off mode + 1 - on in normal mode + 2 - low power mode + 3 - suspend mode + +The following are the names of the regulators that the s5m8767 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s5m8767. + + - LDOn + - valid values for n are 1 to 28 + - Example: LDO0, LD01, LDO28 + - BUCKn + - valid values for n are 1 to 9. + - Example: BUCK1, BUCK2, BUCK9 + +The bindings inside the regulator nodes use the standard regulator bindings +which are documented elsewhere. + +Example: + + s5m8767_pmic@66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + + s5m8767,pmic-buck2-uses-gpio-dvs; + s5m8767,pmic-buck3-uses-gpio-dvs; + s5m8767,pmic-buck4-uses-gpio-dvs; + + s5m8767,pmic-buck-default-dvs-idx = <0>; + + s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */ + <&gpx0 1 1 0 0>, /* DVS2 */ + <&gpx0 2 1 0 0>; /* DVS3 */ + + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */ + <&gpx2 4 1 0 0>, /* SET2 */ + <&gpx2 5 1 0 0>; /* SET3 */ + + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt b/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt new file mode 100644 index 00000000000..2f7e44a9641 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt @@ -0,0 +1,27 @@ +TPS51632 Voltage regulators + +Required properties: +- compatible: Must be "ti,tps51632" +- reg: I2C slave address + +Optional properties: +- ti,enable-pwm-dvfs: Enable the DVFS voltage control through the PWM interface. +- ti,dvfs-step-20mV: The 20mV step voltage when PWM DVFS enabled. Missing this + will set 10mV step voltage in PWM DVFS mode. In normal mode, the voltage + step is 10mV as per datasheet. + +Any property defined as part of the core regulator binding, defined in +regulator.txt, can also be used. + +Example: + + tps51632 { + compatible = "ti,tps51632"; + reg = <0x43>; + regulator-name = "tps51632-vout"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + ti,enable-pwm-dvfs; + ti,dvfs-step-20mV; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt b/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt index c8ca6b8f658..1b20c3dbcdb 100644 --- a/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt @@ -17,9 +17,9 @@ Optional properties: - ti,vsel1-gpio: Gpio for controlling VSEL1 line. If this property is missing, then assume that there is no GPIO for vsel1 control. -- ti,vsel0-state-high: Inital state of vsel0 input is high. +- ti,vsel0-state-high: Initial state of vsel0 input is high. If this property is missing, then assume the state as low (0). -- ti,vsel1-state-high: Inital state of vsel1 input is high. +- ti,vsel1-state-high: Initial state of vsel1 input is high. If this property is missing, then assume the state as low (0). Any property defined as part of the core regulator binding, defined in diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt new file mode 100644 index 00000000000..313a60ba61d --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -0,0 +1,122 @@ +TPS65090 regulators + +Required properties: +- compatible: "ti,tps65090" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + dcdc[1-3], fet[1-7] and ldo[1-2] respectively. +- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively. +- infet[1-7]-supply: The input supply for FET[1-7] respectively. +- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively. + +Optional properties: +- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled then this property should be there. +- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled and if it is from GPIO then GPIO + number should be provided. If it is externally controlled and no GPIO + entry then driver will just configure this rails as external control + and will not provide any enable/disable APIs. + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps65090@48 { + compatible = "ti,tps65090"; + reg = <0x48>; + interrupts = <0 88 0x4>; + + vsys1-supply = <&some_reg>; + vsys2-supply = <&some_reg>; + vsys3-supply = <&some_reg>; + infet1-supply = <&some_reg>; + infet2-supply = <&some_reg>; + infet3-supply = <&some_reg>; + infet4-supply = <&some_reg>; + infet5-supply = <&some_reg>; + infet6-supply = <&some_reg>; + infet7-supply = <&some_reg>; + vsys_l1-supply = <&some_reg>; + vsys_l2-supply = <&some_reg>; + + regulators { + dcdc1 { + regulator-name = "dcdc1"; + regulator-boot-on; + regulator-always-on; + ti,enable-ext-control; + dcdc-ext-control-gpios = <&gpio 10 0>; + }; + + dcdc2 { + regulator-name = "dcdc2"; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3 { + regulator-name = "dcdc3"; + regulator-boot-on; + regulator-always-on; + }; + + fet1 { + regulator-name = "fet1"; + regulator-boot-on; + regulator-always-on; + }; + + fet2 { + regulator-name = "fet2"; + regulator-boot-on; + regulator-always-on; + }; + + fet3 { + regulator-name = "fet3"; + regulator-boot-on; + regulator-always-on; + }; + + fet4 { + regulator-name = "fet4"; + regulator-boot-on; + regulator-always-on; + }; + + fet5 { + regulator-name = "fet5"; + regulator-boot-on; + regulator-always-on; + }; + + fet6 { + regulator-name = "fet6"; + regulator-boot-on; + regulator-always-on; + }; + + fet7 { + regulator-name = "fet7"; + regulator-boot-on; + regulator-always-on; + }; + + ldo1 { + regulator-name = "ldo1"; + regulator-boot-on; + regulator-always-on; + }; + + ldo2 { + regulator-name = "ldo2"; + regulator-boot-on; + regulator-always-on; + }; + }; + }; |