diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
5 files changed, 110 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt new file mode 100644 index 00000000000..a590ca51be7 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -0,0 +1,34 @@ +* Energy Micro EFM32 SPI + +Required properties: +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- compatible: should be "efm32,spi" +- reg: Offset and length of the register set for the controller +- interrupts: pair specifying rx and tx irq +- clocks: phandle to the spi clock +- cs-gpios: see spi-bus.txt +- location: Value to write to the ROUTE register's LOCATION bitfield to configure the pinmux for the device, see datasheet for values. + +Example: + +spi1: spi@0x4000c400 { /* USART1 */ + #address-cells = <1>; + #size-cells = <0>; + compatible = "efm32,spi"; + reg = <0x4000c400 0x400>; + interrupts = <15 16>; + clocks = <&cmu 20>; + cs-gpios = <&gpio 51 1>; // D3 + location = <1>; + status = "ok"; + + ks8851@0 { + compatible = "ks8851"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&boardfpga>; + interrupts = <4>; + status = "ok"; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 296015e3c63..800dafe5b01 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -55,6 +55,16 @@ contain the following properties. chip select active high - spi-3wire - (optional) Empty property indicating device requires 3-wire mode. +- spi-tx-bus-width - (optional) The bus width(number of data wires) that + used for MOSI. Defaults to 1 if not present. +- spi-rx-bus-width - (optional) The bus width(number of data wires) that + used for MISO. Defaults to 1 if not present. + +Some SPI controllers and devices support Dual and Quad SPI transfer mode. +It allows data in SPI system transfered in 2 wires(DUAL) or 4 wires(QUAD). +Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is +only 1(SINGLE), 2(DUAL) and 4(QUAD). +Dual/Quad mode is not allowed when 3-wire mode is used. If a gpio chipselect is used for the SPI slave the gpio number will be passed via the cs_gpio diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt new file mode 100644 index 00000000000..a1fb3035a42 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -0,0 +1,42 @@ +ARM Freescale DSPI controller + +Required properties: +- compatible : "fsl,vf610-dspi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI controller interrupt +- clocks: from common clock binding: handle to dspi clock. +- clock-names: from common clock binding: Shall be "dspi". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must contain a "default" entry. +- spi-num-chipselects : the number of the chipselect signals. +- bus-num : the slave chip chipselect signal number. +Example: + +dspi0@4002c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-dspi"; + reg = <0x4002c000 0x1000>; + interrupts = <0 67 0x04>; + clocks = <&clks VF610_CLK_DSPI0>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + bus-num = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi0_1>; + status = "okay"; + + sflash: at26df081a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at26df081a"; + spi-max-frequency = <16000000>; + spi-cpol; + spi-cpha; + reg = <0>; + linux,modalias = "m25p80"; + modal = "at26df081a"; + }; +}; + + diff --git a/Documentation/devicetree/bindings/spi/spi_altera.txt b/Documentation/devicetree/bindings/spi/spi_altera.txt index dda37594350..31319dcf30a 100644 --- a/Documentation/devicetree/bindings/spi/spi_altera.txt +++ b/Documentation/devicetree/bindings/spi/spi_altera.txt @@ -1,4 +1,5 @@ Altera SPI Required properties: -- compatible : should be "ALTR,spi-1.0". +- compatible : should be "ALTR,spi-1.0". <DEPRECATED> +- compatible : should be "altr,spi-1.0". diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt new file mode 100644 index 00000000000..1f9641ade0b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -0,0 +1,22 @@ +TI QSPI controller. + +Required properties: +- compatible : should be "ti,dra7xxx-qspi" or "ti,am4372-qspi". +- reg: Should contain QSPI registers location and length. +- #address-cells, #size-cells : Must be present if the device has sub-nodes +- ti,hwmods: Name of the hwmod associated to the QSPI + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +qspi: qspi@4b300000 { + compatible = "ti,dra7xxx-qspi"; + reg = <0x4b300000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <25000000>; + ti,hwmods = "qspi"; +}; |