diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
7 files changed, 147 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt new file mode 100644 index 00000000000..8bf89c64364 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt @@ -0,0 +1,22 @@ +Broadcom BCM2835 SPI0 controller + +The BCM2835 contains two forms of SPI master controller, one known simply as +SPI0, and the other known as the "Universal SPI Master"; part of the +auxilliary block. This binding applies to the SPI0 controller. + +Required properties: +- compatible: Should be "brcm,bcm2835-spi". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks: The clock feeding the SPI controller. + +Example: + +spi@20204000 { + compatible = "brcm,bcm2835-spi"; + reg = <0x7e204000 0x1000>; + interrupts = <2 22>; + clocks = <&clk_spi>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt index 777abd7399d..b032dd76e9d 100644 --- a/Documentation/devicetree/bindings/spi/fsl-spi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -4,7 +4,7 @@ Required properties: - cell-index : QE SPI subblock index. 0: QE subblock SPI1 1: QE subblock SPI2 -- compatible : should be "fsl,spi". +- compatible : should be "fsl,spi" or "aeroflexgaisler,spictrl". - mode : the SPI operation mode, it can be "cpu" or "cpu-qe". - reg : Offset and length of the register set for the device - interrupts : <a b> where a is the interrupt number and b is a @@ -14,6 +14,7 @@ Required properties: controller you have. - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. +- clock-frequency : input clock frequency to non FSL_SOC cores Optional properties: - gpios : specifies the gpio pins to be used for chipselects. diff --git a/Documentation/devicetree/bindings/spi/mxs-spi.txt b/Documentation/devicetree/bindings/spi/mxs-spi.txt index e2e13957c2a..3499b73293c 100644 --- a/Documentation/devicetree/bindings/spi/mxs-spi.txt +++ b/Documentation/devicetree/bindings/spi/mxs-spi.txt @@ -3,8 +3,11 @@ Required properties: - compatible: Should be "fsl,<soc>-spi", where soc is "imx23" or "imx28" - reg: Offset and length of the register set for the device -- interrupts: Should contain SSP interrupts (error irq first, dma irq second) -- fsl,ssp-dma-channel: APBX DMA channel for the SSP +- interrupts: Should contain SSP ERROR interrupt +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and SSP DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". Optional properties: - clock-frequency : Input clock frequency to the SPI block in Hz. @@ -17,6 +20,7 @@ ssp0: ssp@80010000 { #size-cells = <0>; compatible = "fsl,imx28-spi"; reg = <0x80010000 0x2000>; - interrupts = <96 82>; - fsl,ssp-dma-channel = <0>; + interrupts = <96>; + dmas = <&dma_apbh 0>; + dma-names = "rx-tx"; }; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt new file mode 100644 index 00000000000..91ff771c7e7 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt @@ -0,0 +1,26 @@ +NVIDIA Tegra114 SPI controller. + +Required properties: +- compatible : should be "nvidia,tegra114-spi". +- reg: Should contain SPI registers location and length. +- interrupts: Should contain SPI interrupts. +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this SPI controller. +- This is also require clock named "spi" as per binding document + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt +Example: + +spi@7000d600 { + compatible = "nvidia,tegra114-spi"; + reg = <0x7000d600 0x200>; + interrupts = <0 82 0x04>; + nvidia,dma-request-selector = <&apbdma 16>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt new file mode 100644 index 00000000000..6d0ac8d0ad9 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -0,0 +1,51 @@ +Davinci SPI controller device bindings + +Required properties: +- #address-cells: number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: should be zero. +- compatible: + - "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family + - "ti,da830-spi" for SPI used similar to that on DA8xx SoC family +- reg: Offset and length of SPI controller register space +- num-cs: Number of chip selects +- ti,davinci-spi-intr-line: interrupt line used to connect the SPI + IP to the interrupt controller within the SoC. Possible values + are 0 and 1. Manual says one of the two possible interrupt + lines can be tied to the interrupt controller. Set this + based on a specifc SoC configuration. +- interrupts: interrupt number mapped to CPU. +- clocks: spi clk phandle + +Example of a NOR flash slave device (n25q032) connected to DaVinci +SPI controller device over the SPI bus. + +spi0:spi@20BF0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,dm6446-spi"; + reg = <0x20BF0000 0x1000>; + num-cs = <4>; + ti,davinci-spi-intr-line = <0>; + interrupts = <338>; + clocks = <&clkspi>; + + flash: n25q032@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p32"; + spi-max-frequency = <25000000>; + reg = <0>; + + partition@0 { + label = "u-boot-spl"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@1 { + label = "test"; + reg = <0x80000 0x380000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index a15ffeddfba..86aa061f069 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -31,9 +31,6 @@ Required Board Specific Properties: - #address-cells: should be 1. - #size-cells: should be 0. -- gpios: The gpio specifier for clock, mosi and miso interface lines (in the - order specified). The format of the gpio specifier depends on the gpio - controller. Optional Board Specific Properties: @@ -86,9 +83,8 @@ Example: spi_0: spi@12d20000 { #address-cells = <1>; #size-cells = <0>; - gpios = <&gpa2 4 2 3 0>, - <&gpa2 6 2 3 0>, - <&gpa2 7 2 3 0>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_bus>; w25q80bw@0 { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt index f158fd31cfd..22ed6797216 100644 --- a/Documentation/devicetree/bindings/spi/spi_pl022.txt +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -16,6 +16,11 @@ Optional properties: device will be suspended immediately - pl022,rt : indicates the controller should run the message pump with realtime priority to minimise the transfer latency on the bus (boolean) +- dmas : Two or more DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt +- dma-names: Names for the dma channels, if present. There must be at + least one channel named "tx" for transmit and named "rx" for + receive. SPI slave nodes must be children of the SPI master node and can @@ -32,3 +37,34 @@ contain the following properties. - pl022,wait-state : Microwire interface: Wait state - pl022,duplex : Microwire interface: Full/Half duplex + +Example: + + spi@e0100000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0xe0100000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 31 0x4>; + dmas = <&dma-controller 23 1>, + <&dma-controller 24 0>; + dma-names = "rx", "tx"; + + m25p80@1 { + compatible = "st,m25p80"; + reg = <1>; + spi-max-frequency = <12000000>; + spi-cpol; + spi-cpha; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; + }; + |