diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/omap-usb.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/omap-usb.txt | 41 |
1 files changed, 35 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 1ef0ce71f8f..d4769f343d6 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -8,16 +8,17 @@ OMAP MUSB GLUE and disconnect. - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - - num_eps : Specifies the number of endpoints. This is also a + - num-eps : Specifies the number of endpoints. This is also a MUSB configuration-specific setting. Should be set to "16" - - ram_bits : Specifies the ram address size. Should be set to "12" - - interface_type : This is a board specific setting to describe the type of + - ram-bits : Specifies the ram address size. Should be set to "12" + - interface-type : This is a board specific setting to describe the type of interface between the controller and the phy. It should be "0" or "1" specifying ULPI and UTMI respectively. - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" represents PERIPHERAL. - power : Should be "50". This signifies the controller can supply upto 100mA when operating in host mode. + - usb-phy : the phandle for the PHY device Optional properties: - ctrl-module : phandle of the control module this glue uses to write to @@ -29,18 +30,46 @@ usb_otg_hs: usb_otg_hs@4a0ab000 { ti,hwmods = "usb_otg_hs"; ti,has-mailbox; multipoint = <1>; - num_eps = <16>; - ram_bits = <12>; + num-eps = <16>; + ram-bits = <12>; ctrl-module = <&omap_control_usb>; }; Board specific device node entry &usb_otg_hs { - interface_type = <1>; + interface-type = <1>; mode = <3>; power = <50>; }; +OMAP DWC3 GLUE + - compatible : Should be "ti,dwc3" + - ti,hwmods : Should be "usb_otg_ss" + - reg : Address and length of the register set for the device. + - interrupts : The irq number of this device that is used to interrupt the + MPU + - #address-cells, #size-cells : Must be present if the device has sub-nodes + - utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID. + It should be set to "1" for HW mode and "2" for SW mode. + - ranges: the child address space are mapped 1:1 onto the parent address space + +Sub-nodes: +The dwc3 core should be added as subnode to omap dwc3 glue. +- dwc3 : + The binding details of dwc3 can be found in: + Documentation/devicetree/bindings/usb/dwc3.txt + +omap_dwc3 { + compatible = "ti,dwc3"; + ti,hwmods = "usb_otg_ss"; + reg = <0x4a020000 0x1ff>; + interrupts = <0 93 4>; + #address-cells = <1>; + #size-cells = <1>; + utmi-mode = <2>; + ranges; +}; + OMAP CONTROL USB Required properties: |