diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb')
7 files changed, 180 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt new file mode 100644 index 00000000000..7a95c651ceb --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -0,0 +1,22 @@ +synopsys DWC3 CORE + +DWC3- USB3 CONTROLLER + +Required properties: + - compatible: must be "synopsys,dwc3" + - reg : Address and length of the register set for the device + - interrupts: Interrupts used by the dwc3 controller. + - usb-phy : array of phandle for the PHY device + +Optional properties: + - tx-fifo-resize: determines if the FIFO *has* to be reallocated. + +This is usually a subnode to DWC3 glue to which it is connected. + +dwc3@4a030000 { + compatible = "synopsys,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + tx-fifo-resize; +}; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt index e9b005dc762..34c95288327 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt @@ -11,6 +11,7 @@ Required properties : - phy_type : Should be one of "ulpi" or "utmi". - nvidia,vbus-gpio : If present, specifies a gpio that needs to be activated for the bus to be powered. + - nvidia,phy : phandle of the PHY instance, the controller is connected to. Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. @@ -27,3 +28,5 @@ Optional properties: registers are accessed through the APB_MISC base address instead of the USB controller. Since this is a legacy issue it probably does not warrant a compatible string of its own. + - nvidia,needs-double-reset : boolean is to be set for some of the Tegra2 + USB ports, which need reset twice due to hardware issues. diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt new file mode 100644 index 00000000000..6bdaba2f0aa --- /dev/null +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -0,0 +1,17 @@ +Tegra SOC USB PHY + +The device node for Tegra SOC USB PHY: + +Required properties : + - compatible : Should be "nvidia,tegra20-usb-phy". + - reg : Address and length of the register set for the USB PHY interface. + - phy_type : Should be one of "ulpi" or "utmi". + +Required properties for phy_type == ulpi: + - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. + +Optional properties: + - nvidia,has-legacy-mode : boolean indicates whether this controller can + operate in legacy mode (as APX 2500 / 2600). In legacy mode some + registers are accessed through the APB_MISC base address instead of + the USB controller.
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 29a043ecda5..1ef0ce71f8f 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -1,8 +1,11 @@ -OMAP GLUE +OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS OMAP MUSB GLUE - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" - ti,hwmods : must be "usb_otg_hs" + - ti,has-mailbox : to specify that omap uses an external mailbox + (in control module) to communicate with the musb core during device connect + and disconnect. - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - num_eps : Specifies the number of endpoints. This is also a @@ -16,13 +19,19 @@ OMAP MUSB GLUE - power : Should be "50". This signifies the controller can supply upto 100mA when operating in host mode. +Optional properties: + - ctrl-module : phandle of the control module this glue uses to write to + mailbox + SOC specific device node entry usb_otg_hs: usb_otg_hs@4a0ab000 { compatible = "ti,omap4-musb"; ti,hwmods = "usb_otg_hs"; + ti,has-mailbox; multipoint = <1>; num_eps = <16>; ram_bits = <12>; + ctrl-module = <&omap_control_usb>; }; Board specific device node entry @@ -31,3 +40,26 @@ Board specific device node entry mode = <3>; power = <50>; }; + +OMAP CONTROL USB + +Required properties: + - compatible: Should be "ti,omap-control-usb" + - reg : Address and length of the register set for the device. It contains + the address of "control_dev_conf" and "otghs_control" or "phy_power_usb" + depending upon omap4 or omap5. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + - ti,type: This is used to differentiate whether the control module has + usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to + notify events to the musb core and omap5 has usb3 phy power register to + power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3 + phy power. + +omap_control_usb: omap-control-usb@4a002300 { + compatible = "ti,omap-control-usb"; + reg = <0x4a002300 0x4>, + <0x4a00233c 0x4>; + reg-names = "control_dev_conf", "otghs_control"; + ti,type = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt new file mode 100644 index 00000000000..033194934f6 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt @@ -0,0 +1,55 @@ +* Samsung's usb phy transceiver + +The Samsung's phy transceiver is used for controlling usb phy for +s3c-hsotg as well as ehci-s5p and ohci-exynos usb controllers +across Samsung SOCs. +TODO: Adding the PHY binding with controller(s) according to the under +developement generic PHY driver. + +Required properties: + +Exynos4210: +- compatible : should be "samsung,exynos4210-usbphy" +- reg : base physical address of the phy registers and length of memory mapped + region. + +Exynos5250: +- compatible : should be "samsung,exynos5250-usbphy" +- reg : base physical address of the phy registers and length of memory mapped + region. + +Optional properties: +- #address-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- #size-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- ranges: allows valid translation between child's address space and parent's + address space. + +- The child node 'usbphy-sys' to the node 'usbphy' is for the system controller + interface for usb-phy. It should provide the following information required by + usb-phy controller to control phy. + - reg : base physical address of PHY_CONTROL registers. + The size of this register is the total sum of size of all PHY_CONTROL + registers that the SoC has. For example, the size will be + '0x4' in case we have only one PHY_CONTROL register (e.g. + OTHERS register in S3C64XX or USB_PHY_CONTROL register in S5PV210) + and, '0x8' in case we have two PHY_CONTROL registers (e.g. + USBDEVICE_PHY_CONTROL and USBHOST_PHY_CONTROL registers in exynos4x). + and so on. + +Example: + - Exynos4210 + + usbphy@125B0000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,exynos4210-usbphy"; + reg = <0x125B0000 0x100>; + ranges; + + usbphy-sys { + /* USB device and host PHY_CONTROL registers */ + reg = <0x10020704 0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt index 80d4148cb66..61496f5cb09 100644 --- a/Documentation/devicetree/bindings/usb/usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt @@ -4,14 +4,39 @@ OMAP USB2 PHY Required properties: - compatible: Should be "ti,omap-usb2" - - reg : Address and length of the register set for the device. Also -add the address of control module dev conf register until a driver for -control module is added + - reg : Address and length of the register set for the device. + +Optional properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. This is usually a subnode of ocp2scp to which it is connected. usb2phy@4a0ad080 { compatible = "ti,omap-usb2"; - reg = <0x4a0ad080 0x58>, - <0x4a002300 0x4>; + reg = <0x4a0ad080 0x58>; + ctrl-module = <&omap_control_usb>; +}; + +OMAP USB3 PHY + +Required properties: + - compatible: Should be "ti,omap-usb3" + - reg : Address and length of the register set for the device. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + +Optional properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +This is usually a subnode of ocp2scp to which it is connected. + +usb3phy@4a084400 { + compatible = "ti,omap-usb3"; + reg = <0x4a084400 0x80>, + <0x4a084800 0x64>, + <0x4a084c00 0x40>; + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_usb>; }; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt new file mode 100644 index 00000000000..6813a715fc7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -0,0 +1,20 @@ +SMSC USB3503 High-Speed Hub Controller + +Required properties: +- compatible: Should be "smsc,usb3503". +- reg: Specifies the i2c slave address, it should be 0x08. +- connect-gpios: Should specify GPIO for connect. +- intn-gpios: Should specify GPIO for interrupt. +- reset-gpios: Should specify GPIO for reset. +- initial-mode: Should specify initial mode. + (1 for HUB mode, 2 for STANDBY mode) + +Examples: + usb3503@08 { + compatible = "smsc,usb3503"; + reg = <0x08>; + connect-gpios = <&gpx3 0 1>; + intn-gpios = <&gpx3 4 1>; + reset-gpios = <&gpx3 5 1>; + initial-mode = <1>; + }; |