diff options
Diffstat (limited to 'Documentation/devicetree/bindings/video')
10 files changed, 251 insertions, 48 deletions
diff --git a/Documentation/devicetree/bindings/video/backlight/lp855x.txt b/Documentation/devicetree/bindings/video/backlight/lp855x.txt new file mode 100644 index 00000000000..1482103d288 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/lp855x.txt @@ -0,0 +1,41 @@ +lp855x bindings + +Required properties: + - compatible: "ti,lp8550", "ti,lp8551", "ti,lp8552", "ti,lp8553", + "ti,lp8556", "ti,lp8557" + - reg: I2C slave address (u8) + - dev-ctrl: Value of DEVICE CONTROL register (u8). It depends on the device. + +Optional properties: + - bl-name: Backlight device name (string) + - init-brt: Initial value of backlight brightness (u8) + - pwm-period: PWM period value. Set only PWM input mode used (u32) + - rom-addr: Register address of ROM area to be updated (u8) + - rom-val: Register value to be updated (u8) + +Example: + + /* LP8556 */ + backlight@2c { + compatible = "ti,lp8556"; + reg = <0x2c>; + + bl-name = "lcd-bl"; + dev-ctrl = /bits/ 8 <0x85>; + init-brt = /bits/ 8 <0x10>; + }; + + /* LP8557 */ + backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + + dev-ctrl = /bits/ 8 <0x41>; + init-brt = /bits/ 8 <0x0a>; + + /* 4V OV, 4 output LED string enabled */ + rom_14h { + rom-addr = /bits/ 8 <0x14>; + rom-val = /bits/ 8 <0xcf>; + }; + }; diff --git a/Documentation/devicetree/bindings/video/backlight/tps65217-backlight.txt b/Documentation/devicetree/bindings/video/backlight/tps65217-backlight.txt new file mode 100644 index 00000000000..5fb9279ac28 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/tps65217-backlight.txt @@ -0,0 +1,27 @@ +TPS65217 family of regulators + +The TPS65217 chip contains a boost converter and current sinks which can be +used to drive LEDs for use as backlights. + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- backlight: node for specifying WLED1 and WLED2 lines in TPS65217 +- isel: selection bit, valid values: 1 for ISEL1 (low-level) and 2 for ISEL2 (high-level) +- fdim: PWM dimming frequency, valid values: 100, 200, 500, 1000 +- default-brightness: valid values: 0-100 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + reg = <0x24>; + compatible = "ti,tps65217"; + backlight { + isel = <1>; /* 1 - ISET1, 2 ISET2 */ + fdim = <100>; /* TPS65217_BL_FDIM_100HZ */ + default-brightness = <50>; + }; + }; + diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt new file mode 100644 index 00000000000..589edee3739 --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt @@ -0,0 +1,22 @@ +Device-Tree bindings for drm hdmi driver + +Required properties: +- compatible: value should be "samsung,exynos5-hdmi". +- reg: physical base address of the hdmi and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- hpd-gpio: following information about the hotplug gpio pin. + a) phandle of the gpio controller node. + b) pin number within the gpio controller. + c) pin function mode. + d) optional flags and pull up/down. + e) drive strength. + +Example: + + hdmi { + compatible = "samsung,exynos5-hdmi"; + reg = <0x14530000 0x100000>; + interrupts = <0 95 0>; + hpd-gpio = <&gpx3 7 0xf 1 3>; + }; diff --git a/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt new file mode 100644 index 00000000000..fa166d94580 --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt @@ -0,0 +1,12 @@ +Device-Tree bindings for hdmiddc driver + +Required properties: +- compatible: value should be "samsung,exynos5-hdmiddc". +- reg: I2C address of the hdmiddc device. + +Example: + + hdmiddc { + compatible = "samsung,exynos5-hdmiddc"; + reg = <0x50>; + }; diff --git a/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt new file mode 100644 index 00000000000..858f4f9b902 --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt @@ -0,0 +1,12 @@ +Device-Tree bindings for hdmiphy driver + +Required properties: +- compatible: value should be "samsung,exynos5-hdmiphy". +- reg: I2C address of the hdmiphy device. + +Example: + + hdmiphy { + compatible = "samsung,exynos5-hdmiphy"; + reg = <0x38>; + }; diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt new file mode 100644 index 00000000000..9b2ea034356 --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt @@ -0,0 +1,15 @@ +Device-Tree bindings for mixer driver + +Required properties: +- compatible: value should be "samsung,exynos5-mixer". +- reg: physical base address of the mixer and length of memory mapped + region. +- interrupts: interrupt number to the cpu. + +Example: + + mixer { + compatible = "samsung,exynos5-mixer"; + reg = <0x14450000 0x10000>; + interrupts = <0 94 0>; + }; diff --git a/Documentation/devicetree/bindings/video/samsung-fimd.txt b/Documentation/devicetree/bindings/video/samsung-fimd.txt new file mode 100644 index 00000000000..778838a0336 --- /dev/null +++ b/Documentation/devicetree/bindings/video/samsung-fimd.txt @@ -0,0 +1,65 @@ +Device-Tree bindings for Samsung SoC display controller (FIMD) + +FIMD (Fully Interactive Mobile Display) is the Display Controller for the +Samsung series of SoCs which transfers the image data from a video memory +buffer to an external LCD interface. + +Required properties: +- compatible: value should be one of the following + "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */ + "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */ + "samsung,s5p6440-fimd"; /* for S5P64X0 SoCs */ + "samsung,s5pc100-fimd"; /* for S5PC100 SoC */ + "samsung,s5pv210-fimd"; /* for S5PV210 SoC */ + "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ + "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */ + +- reg: physical base address and length of the FIMD registers set. + +- interrupt-parent: should be the phandle of the fimd controller's + parent interrupt controller. + +- interrupts: should contain a list of all FIMD IP block interrupts in the + order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier + format depends on the interrupt controller used. + +- interrupt-names: should contain the interrupt names: "fifo", "vsync", + "lcd_sys", in the same order as they were listed in the interrupts + property. + +- pinctrl-0: pin control group to be used for this controller. + +- pinctrl-names: must contain a "default" entry. + +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. + +- clock-names: list of clock names sorted in the same order as the clocks + property. Must contain "sclk_fimd" and "fimd". + +Optional Properties: +- samsung,power-domain: a phandle to FIMD power domain node. + +Example: + +SoC specific DT entry: + + fimd@11c00000 { + compatible = "samsung,exynos4210-fimd"; + interrupt-parent = <&combiner>; + reg = <0x11c00000 0x20000>; + interrupt-names = "fifo", "vsync", "lcd_sys"; + interrupts = <11 0>, <11 1>, <11 2>; + clocks = <&clock 140>, <&clock 283>; + clock-names = "sclk_fimd", "fimd"; + samsung,power-domain = <&pd_lcd0>; + status = "disabled"; + }; + +Board specific DT entry: + + fimd@11c00000 { + pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>; + pinctrl-names = "default"; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/video/simple-framebuffer.txt b/Documentation/devicetree/bindings/video/simple-framebuffer.txt new file mode 100644 index 00000000000..3ea46058311 --- /dev/null +++ b/Documentation/devicetree/bindings/video/simple-framebuffer.txt @@ -0,0 +1,25 @@ +Simple Framebuffer + +A simple frame-buffer describes a raw memory region that may be rendered to, +with the assumption that the display hardware has already been set up to scan +out from that buffer. + +Required properties: +- compatible: "simple-framebuffer" +- reg: Should contain the location and size of the framebuffer memory. +- width: The width of the framebuffer in pixels. +- height: The height of the framebuffer in pixels. +- stride: The number of bytes in each line of the framebuffer. +- format: The format of the framebuffer surface. Valid values are: + - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b). + +Example: + + framebuffer { + compatible = "simple-framebuffer"; + reg = <0x1d385000 (1600 * 1200 * 2)>; + width = <1600>; + height = <1200>; + stride = <(1600 * 2)>; + format = "r5g6b5"; + }; diff --git a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt index c870b6478ec..2871e218a0f 100644 --- a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt +++ b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt @@ -5,58 +5,32 @@ Required properties: - compatible : "via,vt8500-fb" - reg : Should contain 1 register ranges(address and length) - interrupts : framebuffer controller interrupt -- display: a phandle pointing to the display node +- bits-per-pixel : bit depth of framebuffer (16 or 32) -Required nodes: -- display: a display node is required to initialize the lcd panel - This should be in the board dts. -- default-mode: a videomode within the display with timing parameters - as specified below. +Required subnodes: +- display-timings: see display-timing.txt for information Example: - fb@d800e400 { + fb@d8050800 { compatible = "via,vt8500-fb"; reg = <0xd800e400 0x400>; interrupts = <12>; - display = <&display>; - default-mode = <&mode0>; - }; - -VIA VT8500 Display ------------------------------------------------------ -Required properties (as per of_videomode_helper): - - - hactive, vactive: Display resolution - - hfront-porch, hback-porch, hsync-len: Horizontal Display timing parameters - in pixels - vfront-porch, vback-porch, vsync-len: Vertical display timing parameters in - lines - - clock: displayclock in Hz - - bpp: lcd panel bit-depth. - <16> for RGB565, <32> for RGB888 - -Optional properties (as per of_videomode_helper): - - width-mm, height-mm: Display dimensions in mm - - hsync-active-high (bool): Hsync pulse is active high - - vsync-active-high (bool): Vsync pulse is active high - - interlaced (bool): This is an interlaced mode - - doublescan (bool): This is a doublescan mode + bits-per-pixel = <16>; -Example: - display: display@0 { - modes { - mode0: mode@0 { + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ hactive = <800>; vactive = <480>; - hback-porch = <88>; hfront-porch = <40>; + hback-porch = <88>; hsync-len = <0>; vback-porch = <32>; vfront-porch = <11>; vsync-len = <1>; - clock = <0>; /* unused but required */ - bpp = <16>; /* non-standard but required */ }; }; }; + diff --git a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt index 3d325e1d11e..0bcadb2840a 100644 --- a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt +++ b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt @@ -4,20 +4,30 @@ Wondermedia WM8505 Framebuffer Required properties: - compatible : "wm,wm8505-fb" - reg : Should contain 1 register ranges(address and length) -- via,display: a phandle pointing to the display node +- bits-per-pixel : bit depth of framebuffer (16 or 32) -Required nodes: -- display: a display node is required to initialize the lcd panel - This should be in the board dts. See definition in - Documentation/devicetree/bindings/video/via,vt8500-fb.txt -- default-mode: a videomode node as specified in - Documentation/devicetree/bindings/video/via,vt8500-fb.txt +Required subnodes: +- display-timings: see display-timing.txt for information Example: - fb@d8050800 { + fb@d8051700 { compatible = "wm,wm8505-fb"; - reg = <0xd8050800 0x200>; - display = <&display>; - default-mode = <&mode0>; + reg = <0xd8051700 0x200>; + bits-per-pixel = <16>; + + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <88>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; + }; + }; }; |