diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
3 files changed, 86 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt index 3c046ee6e8b..c80e8a3402f 100644 --- a/Documentation/devicetree/bindings/dma/atmel-dma.txt +++ b/Documentation/devicetree/bindings/dma/atmel-dma.txt @@ -1,14 +1,39 @@ * Atmel Direct Memory Access Controller (DMA) Required properties: -- compatible: Should be "atmel,<chip>-dma" -- reg: Should contain DMA registers location and length -- interrupts: Should contain DMA interrupt +- compatible: Should be "atmel,<chip>-dma". +- reg: Should contain DMA registers location and length. +- interrupts: Should contain DMA interrupt. +- #dma-cells: Must be <2>, used to represent the number of integer cells in +the dmas property of client devices. -Examples: +Example: -dma@ffffec00 { +dma0: dma@ffffec00 { compatible = "atmel,at91sam9g45-dma"; reg = <0xffffec00 0x200>; interrupts = <21>; + #dma-cells = <2>; +}; + +DMA clients connected to the Atmel DMA controller must use the format +described in the dma.txt file, using a three-cell specifier for each channel: +a phandle plus two interger cells. +The three cells in order are: + +1. A phandle pointing to the DMA controller. +2. The memory interface (16 most significant bits), the peripheral interface +(16 less significant bits). +3. The peripheral identifier for the hardware handshaking interface. The +identifier can be different for tx and rx. + +Example: + +i2c0@i2c@f8010000 { + compatible = "atmel,at91sam9x5-i2c"; + reg = <0xf8010000 0x100>; + interrupts = <9 4 6>; + dmas = <&dma0 1 7>, + <&dma0 1 8>; + dma-names = "tx", "rx"; }; diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index 6e1f61f1e78..9315ac96b49 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -5,8 +5,12 @@ on platforms which have strong conventions about which portions of a flash are used for what purposes, but which don't use an on-flash partition table such as RedBoot. -#address-cells & #size-cells must both be present in the mtd device and be -equal to 1. +#address-cells & #size-cells must both be present in the mtd device. There are +two valid values for both: +<1>: for partitions that require a single 32-bit cell to represent their + size/address (aka the value is below 4 GiB) +<2>: for partitions that require two 32-bit cells to represent their + size/address (aka the value is 4 GiB or greater). Required properties: - reg : The partition's offset and size within the mtd bank. @@ -36,3 +40,31 @@ flash@0 { reg = <0x0100000 0x200000>; }; }; + +flash@1 { + #address-cells = <1>; + #size-cells = <2>; + + /* a 4 GiB partition */ + partition@0 { + label = "filesystem"; + reg = <0x00000000 0x1 0x00000000>; + }; +}; + +flash@2 { + #address-cells = <2>; + #size-cells = <2>; + + /* an 8 GiB partition */ + partition@0 { + label = "filesystem #1"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; + + /* a 4 GiB partition */ + partition@200000000 { + label = "filesystem #2"; + reg = <0x2 0x00000000 0x1 0x00000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/thermal/armada-thermal.txt b/Documentation/devicetree/bindings/thermal/armada-thermal.txt new file mode 100644 index 00000000000..fff93d5f92d --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/armada-thermal.txt @@ -0,0 +1,22 @@ +* Marvell Armada 370/XP thermal management + +Required properties: + +- compatible: Should be set to one of the following: + marvell,armada370-thermal + marvell,armadaxp-thermal + +- reg: Device's register space. + Two entries are expected, see the examples below. + The first one is required for the sensor register; + the second one is required for the control register + to be used for sensor initialization (a.k.a. calibration). + +Example: + + thermal@d0018300 { + compatible = "marvell,armada370-thermal"; + reg = <0xd0018300 0x4 + 0xd0018304 0x4>; + status = "okay"; + }; |