aboutsummaryrefslogtreecommitdiff
path: root/Documentation/input/sentelic.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/input/sentelic.txt')
-rw-r--r--Documentation/input/sentelic.txt364
1 files changed, 333 insertions, 31 deletions
diff --git a/Documentation/input/sentelic.txt b/Documentation/input/sentelic.txt
index b2ef125b71f..89251e2a3eb 100644
--- a/Documentation/input/sentelic.txt
+++ b/Documentation/input/sentelic.txt
@@ -1,5 +1,5 @@
-Copyright (C) 2002-2010 Sentelic Corporation.
-Last update: Jan-13-2010
+Copyright (C) 2002-2011 Sentelic Corporation.
+Last update: Dec-07-2011
==============================================================================
* Finger Sensing Pad Intellimouse Mode(scrolling wheel, 4th and 5th buttons)
@@ -140,6 +140,7 @@ BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------
Byte 1: Bit7~Bit6 => 00, Normal data packet
=> 01, Absolute coordination packet
=> 10, Notify packet
+ => 11, Normal data packet with on-pad click
Bit5 => Valid bit, 0 means that the coordinate is invalid or finger up.
When both fingers are up, the last two reports have zero valid
bit.
@@ -164,6 +165,7 @@ BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------
Byte 1: Bit7~Bit6 => 00, Normal data packet
=> 01, Absolute coordinates packet
=> 10, Notify packet
+ => 11, Normal data packet with on-pad click
Bit5 => Valid bit, 0 means that the coordinate is invalid or finger up.
When both fingers are up, the last two reports have zero valid
bit.
@@ -188,6 +190,7 @@ BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------
Byte 1: Bit7~Bit6 => 00, Normal data packet
=> 01, Absolute coordinates packet
=> 10, Notify packet
+ => 11, Normal data packet with on-pad click
Bit5 => 1
Bit4 => when in absolute coordinates mode (valid when EN_PKT_GO is 1):
0: left button is generated by the on-pad command
@@ -205,7 +208,7 @@ Byte 4: Bit7 => scroll right button
Bit6 => scroll left button
Bit5 => scroll down button
Bit4 => scroll up button
- * Note that if gesture and additional buttoni (Bit4~Bit7)
+ * Note that if gesture and additional button (Bit4~Bit7)
happen at the same time, the button information will not
be sent.
Bit3~Bit0 => Reserved
@@ -227,6 +230,7 @@ BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------
Byte 1: Bit7~Bit6 => 00, Normal data packet
=> 01, Absolute coordinates packet
=> 10, Notify packet
+ => 11, Normal data packet with on-pad click
Bit5 => Valid bit, 0 means that the coordinate is invalid or finger up.
When both fingers are up, the last two reports have zero valid
bit.
@@ -253,6 +257,7 @@ BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------
Byte 1: Bit7~Bit6 => 00, Normal data packet
=> 01, Absolute coordination packet
=> 10, Notify packet
+ => 11, Normal data packet with on-pad click
Bit5 => Valid bit, 0 means that the coordinate is invalid or finger up.
When both fingers are up, the last two reports have zero valid
bit.
@@ -279,8 +284,9 @@ BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------
Byte 1: Bit7~Bit6 => 00, Normal data packet
=> 01, Absolute coordination packet
=> 10, Notify packet
+ => 11, Normal data packet with on-pad click
Bit5 => 1
- Bit4 => when in absolute coordinate mode (valid when EN_PKT_GO is 1):
+ Bit4 => when in absolute coordinates mode (valid when EN_PKT_GO is 1):
0: left button is generated by the on-pad command
1: left button is generated by the external button
Bit3 => 1
@@ -307,6 +313,110 @@ Sample sequence of Multi-finger, Multi-coordinate mode:
abs pkt 2, ..., notify packet (valid bit == 0)
==============================================================================
+* Absolute position for STL3888-Cx and STL3888-Dx.
+==============================================================================
+Single Finger, Absolute Coordinate Mode (SFAC)
+ Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
+BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------|
+ 1 |0|1|0|P|1|M|R|L| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 |r|l|B|F|X|X|Y|Y|
+ |---------------| |---------------| |---------------| |---------------|
+
+Byte 1: Bit7~Bit6 => 00, Normal data packet
+ => 01, Absolute coordinates packet
+ => 10, Notify packet
+ Bit5 => Coordinate mode(always 0 in SFAC mode):
+ 0: single-finger absolute coordinates (SFAC) mode
+ 1: multi-finger, multiple coordinates (MFMC) mode
+ Bit4 => 0: The LEFT button is generated by on-pad command (OPC)
+ 1: The LEFT button is generated by external button
+ Default is 1 even if the LEFT button is not pressed.
+ Bit3 => Always 1, as specified by PS/2 protocol.
+ Bit2 => Middle Button, 1 is pressed, 0 is not pressed.
+ Bit1 => Right Button, 1 is pressed, 0 is not pressed.
+ Bit0 => Left Button, 1 is pressed, 0 is not pressed.
+Byte 2: X coordinate (xpos[9:2])
+Byte 3: Y coordinate (ypos[9:2])
+Byte 4: Bit1~Bit0 => Y coordinate (xpos[1:0])
+ Bit3~Bit2 => X coordinate (ypos[1:0])
+ Bit4 => 4th mouse button(forward one page)
+ Bit5 => 5th mouse button(backward one page)
+ Bit6 => scroll left button
+ Bit7 => scroll right button
+
+Multi Finger, Multiple Coordinates Mode (MFMC):
+ Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
+BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------|
+ 1 |0|1|1|P|1|F|R|L| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 |r|l|B|F|X|X|Y|Y|
+ |---------------| |---------------| |---------------| |---------------|
+
+Byte 1: Bit7~Bit6 => 00, Normal data packet
+ => 01, Absolute coordination packet
+ => 10, Notify packet
+ Bit5 => Coordinate mode (always 1 in MFMC mode):
+ 0: single-finger absolute coordinates (SFAC) mode
+ 1: multi-finger, multiple coordinates (MFMC) mode
+ Bit4 => 0: The LEFT button is generated by on-pad command (OPC)
+ 1: The LEFT button is generated by external button
+ Default is 1 even if the LEFT button is not pressed.
+ Bit3 => Always 1, as specified by PS/2 protocol.
+ Bit2 => Finger index, 0 is the first finger, 1 is the second finger.
+ If bit 1 and 0 are all 1 and bit 4 is 0, the middle external
+ button is pressed.
+ Bit1 => Right Button, 1 is pressed, 0 is not pressed.
+ Bit0 => Left Button, 1 is pressed, 0 is not pressed.
+Byte 2: X coordinate (xpos[9:2])
+Byte 3: Y coordinate (ypos[9:2])
+Byte 4: Bit1~Bit0 => Y coordinate (xpos[1:0])
+ Bit3~Bit2 => X coordinate (ypos[1:0])
+ Bit4 => 4th mouse button(forward one page)
+ Bit5 => 5th mouse button(backward one page)
+ Bit6 => scroll left button
+ Bit7 => scroll right button
+
+ When one of the two fingers is up, the device will output four consecutive
+MFMC#0 report packets with zero X and Y to represent 1st finger is up or
+four consecutive MFMC#1 report packets with zero X and Y to represent that
+the 2nd finger is up. On the other hand, if both fingers are up, the device
+will output four consecutive single-finger, absolute coordinate(SFAC) packets
+with zero X and Y.
+
+Notify Packet for STL3888-Cx/Dx
+ Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
+BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------|
+ 1 |1|0|0|P|1|M|R|L| 2 |C|C|C|C|C|C|C|C| 3 |0|0|F|F|0|0|0|i| 4 |r|l|u|d|0|0|0|0|
+ |---------------| |---------------| |---------------| |---------------|
+
+Byte 1: Bit7~Bit6 => 00, Normal data packet
+ => 01, Absolute coordinates packet
+ => 10, Notify packet
+ Bit5 => Always 0
+ Bit4 => 0: The LEFT button is generated by on-pad command(OPC)
+ 1: The LEFT button is generated by external button
+ Default is 1 even if the LEFT button is not pressed.
+ Bit3 => 1
+ Bit2 => Middle Button, 1 is pressed, 0 is not pressed.
+ Bit1 => Right Button, 1 is pressed, 0 is not pressed.
+ Bit0 => Left Button, 1 is pressed, 0 is not pressed.
+Byte 2: Message type:
+ 0xba => gesture information
+ 0xc0 => one finger hold-rotating gesture
+Byte 3: The first parameter for the received message:
+ 0xba => gesture ID (refer to the 'Gesture ID' section)
+ 0xc0 => region ID
+Byte 4: The second parameter for the received message:
+ 0xba => N/A
+ 0xc0 => finger up/down information
+
+Sample sequence of Multi-finger, Multi-coordinates mode:
+
+ notify packet (valid bit == 1), MFMC packet 1 (byte 1, bit 2 == 0),
+ MFMC packet 2 (byte 1, bit 2 == 1), MFMC packet 1, MFMC packet 2,
+ ..., notify packet (valid bit == 0)
+
+ That is, when the device is in MFMC mode, the host will receive
+ interleaved absolute coordinate packets for each finger.
+
+==============================================================================
* FSP Enable/Disable packet
==============================================================================
Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
@@ -348,9 +458,10 @@ http://www.computer-engineering.org/ps2mouse/
==============================================================================
1. Identify FSP by reading device ID(0x00) and version(0x01) register
-2. Determine number of buttons by reading status2 (0x0b) register
+2a. For FSP version < STL3888 Cx, determine number of buttons by reading
+ the 'test mode status' (0x20) register:
- buttons = reg[0x0b] & 0x30
+ buttons = reg[0x20] & 0x30
if buttons == 0x30 or buttons == 0x20:
# two/four buttons
@@ -365,6 +476,10 @@ http://www.computer-engineering.org/ps2mouse/
Refer to 'Finger Sensing Pad PS/2 Mouse Intellimouse'
section A for packet parsing detail
+2b. For FSP version >= STL3888 Cx:
+ Refer to 'Finger Sensing Pad PS/2 Mouse Intellimouse'
+ section A for packet parsing detail (ignore byte 4, bit ~ 7)
+
==============================================================================
* Programming Sequence for Register Reading/Writing
==============================================================================
@@ -374,7 +489,7 @@ Register inversion requirement:
Following values needed to be inverted(the '~' operator in C) before being
sent to FSP:
- 0xe9, 0xee, 0xf2 and 0xff.
+ 0xe8, 0xe9, 0xee, 0xf2, 0xf3 and 0xff.
Register swapping requirement:
@@ -415,7 +530,18 @@ Register reading sequence:
8. send 0xe9(status request) PS/2 command to FSP;
- 9. the response read from FSP should be the requested register value.
+ 9. the 4th byte of the response read from FSP should be the
+ requested register value(?? indicates don't care byte):
+
+ host: 0xe9
+ 3888: 0xfa (??) (??) (val)
+
+ * Note that since the Cx release, the hardware will return 1's
+ complement of the register value at the 3rd byte of status request
+ result:
+
+ host: 0xe9
+ 3888: 0xfa (??) (~val) (val)
Register writing sequence:
@@ -465,71 +591,194 @@ Register writing sequence:
9. the register writing sequence is completed.
+ * Note that since the Cx release, the hardware will return 1's
+ complement of the register value at the 3rd byte of status request
+ result. Host can optionally send another 0xe9 (status request) PS/2
+ command to FSP at the end of register writing to verify that the
+ register writing operation is successful (?? indicates don't care
+ byte):
+
+ host: 0xe9
+ 3888: 0xfa (??) (~val) (val)
+
+==============================================================================
+* Programming Sequence for Page Register Reading/Writing
+==============================================================================
+
+ In order to overcome the limitation of maximum number of registers
+supported, the hardware separates register into different groups called
+'pages.' Each page is able to include up to 255 registers.
+
+ The default page after power up is 0x82; therefore, if one has to get
+access to register 0x8301, one has to use following sequence to switch
+to page 0x83, then start reading/writing from/to offset 0x01 by using
+the register read/write sequence described in previous section.
+
+Page register reading sequence:
+
+ 1. send 0xf3 PS/2 command to FSP;
+
+ 2. send 0x66 PS/2 command to FSP;
+
+ 3. send 0x88 PS/2 command to FSP;
+
+ 4. send 0xf3 PS/2 command to FSP;
+
+ 5. send 0x83 PS/2 command to FSP;
+
+ 6. send 0x88 PS/2 command to FSP;
+
+ 7. send 0xe9(status request) PS/2 command to FSP;
+
+ 8. the response read from FSP should be the requested page value.
+
+Page register writing sequence:
+
+ 1. send 0xf3 PS/2 command to FSP;
+
+ 2. send 0x38 PS/2 command to FSP;
+
+ 3. send 0x88 PS/2 command to FSP;
+
+ 4. send 0xf3 PS/2 command to FSP;
+
+ 5. if the page address being written is not required to be
+ inverted(refer to the 'Register inversion requirement' section),
+ goto step 6
+
+ 5a. send 0x47 PS/2 command to FSP;
+
+ 5b. send the inverted page address to FSP and goto step 9;
+
+ 6. if the page address being written is not required to be
+ swapped(refer to the 'Register swapping requirement' section),
+ goto step 7
+
+ 6a. send 0x44 PS/2 command to FSP;
+
+ 6b. send the swapped page address to FSP and goto step 9;
+
+ 7. send 0x33 PS/2 command to FSP;
+
+ 8. send the page address to FSP;
+
+ 9. the page register writing sequence is completed.
+
+==============================================================================
+* Gesture ID
+==============================================================================
+
+ Unlike other devices which sends multiple fingers' coordinates to host,
+FSP processes multiple fingers' coordinates internally and convert them
+into a 8 bits integer, namely 'Gesture ID.' Following is a list of
+supported gesture IDs:
+
+ ID Description
+ 0x86 2 finger straight up
+ 0x82 2 finger straight down
+ 0x80 2 finger straight right
+ 0x84 2 finger straight left
+ 0x8f 2 finger zoom in
+ 0x8b 2 finger zoom out
+ 0xc0 2 finger curve, counter clockwise
+ 0xc4 2 finger curve, clockwise
+ 0x2e 3 finger straight up
+ 0x2a 3 finger straight down
+ 0x28 3 finger straight right
+ 0x2c 3 finger straight left
+ 0x38 palm
+
==============================================================================
* Register Listing
==============================================================================
+ Registers are represented in 16 bits values. The higher 8 bits represent
+the page address and the lower 8 bits represent the relative offset within
+that particular page. Refer to the 'Programming Sequence for Page Register
+Reading/Writing' section for instructions on how to change current page
+address.
+
offset width default r/w name
-0x00 bit7~bit0 0x01 RO device ID
+0x8200 bit7~bit0 0x01 RO device ID
-0x01 bit7~bit0 0xc0 RW version ID
+0x8201 bit7~bit0 RW version ID
+ 0xc1: STL3888 Ax
+ 0xd0 ~ 0xd2: STL3888 Bx
+ 0xe0 ~ 0xe1: STL3888 Cx
+ 0xe2 ~ 0xe3: STL3888 Dx
-0x02 bit7~bit0 0x01 RO vendor ID
+0x8202 bit7~bit0 0x01 RO vendor ID
-0x03 bit7~bit0 0x01 RO product ID
+0x8203 bit7~bit0 0x01 RO product ID
-0x04 bit3~bit0 0x01 RW revision ID
+0x8204 bit3~bit0 0x01 RW revision ID
-0x0b RO test mode status 1
- bit3 1 RO 0: rotate 180 degree, 1: no rotation
+0x820b test mode status 1
+ bit3 1 RO 0: rotate 180 degree
+ 1: no rotation
+ *only supported by H/W prior to Cx
- bit5~bit4 RO number of buttons
- 11 => 2, lbtn/rbtn
- 10 => 4, lbtn/rbtn/scru/scrd
- 01 => 6, lbtn/rbtn/scru/scrd/scrl/scrr
- 00 => 6, lbtn/rbtn/scru/scrd/fbtn/bbtn
+0x820f register file page control
+ bit2 0 RW 1: rotate 180 degree
+ 0: no rotation
+ *supported since Cx
-0x0f RW register file page control
bit0 0 RW 1 to enable page 1 register files
+ *only supported by H/W prior to Cx
-0x10 RW system control 1
+0x8210 RW system control 1
bit0 1 RW Reserved, must be 1
bit1 0 RW Reserved, must be 0
- bit4 1 RW Reserved, must be 0
- bit5 0 RW register clock gating enable
+ bit4 0 RW Reserved, must be 0
+ bit5 1 RW register clock gating enable
0: read only, 1: read/write enable
(Note that following registers does not require clock gating being
enabled prior to write: 05 06 07 08 09 0c 0f 10 11 12 16 17 18 23 2e
40 41 42 43. In addition to that, this bit must be 1 when gesture
mode is enabled)
-0x31 RW on-pad command detection
+0x8220 test mode status
+ bit5~bit4 RO number of buttons
+ 11 => 2, lbtn/rbtn
+ 10 => 4, lbtn/rbtn/scru/scrd
+ 01 => 6, lbtn/rbtn/scru/scrd/scrl/scrr
+ 00 => 6, lbtn/rbtn/scru/scrd/fbtn/bbtn
+ *only supported by H/W prior to Cx
+
+0x8231 RW on-pad command detection
bit7 0 RW on-pad command left button down tag
enable
0: disable, 1: enable
+ *only supported by H/W prior to Cx
-0x34 RW on-pad command control 5
+0x8234 RW on-pad command control 5
bit4~bit0 0x05 RW XLO in 0s/4/1, so 03h = 0010.1b = 2.5
(Note that position unit is in 0.5 scanline)
+ *only supported by H/W prior to Cx
bit7 0 RW on-pad tap zone enable
0: disable, 1: enable
+ *only supported by H/W prior to Cx
-0x35 RW on-pad command control 6
+0x8235 RW on-pad command control 6
bit4~bit0 0x1d RW XHI in 0s/4/1, so 19h = 1100.1b = 12.5
(Note that position unit is in 0.5 scanline)
+ *only supported by H/W prior to Cx
-0x36 RW on-pad command control 7
+0x8236 RW on-pad command control 7
bit4~bit0 0x04 RW YLO in 0s/4/1, so 03h = 0010.1b = 2.5
(Note that position unit is in 0.5 scanline)
+ *only supported by H/W prior to Cx
-0x37 RW on-pad command control 8
+0x8237 RW on-pad command control 8
bit4~bit0 0x13 RW YHI in 0s/4/1, so 11h = 1000.1b = 8.5
(Note that position unit is in 0.5 scanline)
+ *only supported by H/W prior to Cx
-0x40 RW system control 5
+0x8240 RW system control 5
bit1 0 RW FSP Intellimouse mode enable
0: disable, 1: enable
+ *only supported by H/W prior to Cx
bit2 0 RW movement + abs. coordinate mode enable
0: disable, 1: enable
@@ -537,6 +786,7 @@ offset width default r/w name
bit 1 is not set. However, the format is different from that of bit 1.
In addition, when bit 1 and bit 2 are set at the same time, bit 2 will
override bit 1.)
+ *only supported by H/W prior to Cx
bit3 0 RW abs. coordinate only mode enable
0: disable, 1: enable
@@ -544,9 +794,11 @@ offset width default r/w name
bit 1 is not set. However, the format is different from that of bit 1.
In addition, when bit 1, bit 2 and bit 3 are set at the same time,
bit 3 will override bit 1 and 2.)
+ *only supported by H/W prior to Cx
bit5 0 RW auto switch enable
0: disable, 1: enable
+ *only supported by H/W prior to Cx
bit6 0 RW G0 abs. + notify packet format enable
0: disable, 1: enable
@@ -554,18 +806,68 @@ offset width default r/w name
bit 2 and 3. That is, if any of those bit is 1, host will receive
absolute coordinates; otherwise, host only receives packets with
relative coordinate.)
+ *only supported by H/W prior to Cx
bit7 0 RW EN_PS2_F2: PS/2 gesture mode 2nd
finger packet enable
0: disable, 1: enable
+ *only supported by H/W prior to Cx
-0x43 RW on-pad control
+0x8243 RW on-pad control
bit0 0 RW on-pad control enable
0: disable, 1: enable
(Note that if this bit is cleared, bit 3/5 will be ineffective)
+ *only supported by H/W prior to Cx
bit3 0 RW on-pad fix vertical scrolling enable
0: disable, 1: enable
+ *only supported by H/W prior to Cx
bit5 0 RW on-pad fix horizontal scrolling enable
0: disable, 1: enable
+ *only supported by H/W prior to Cx
+
+0x8290 RW software control register 1
+ bit0 0 RW absolute coordination mode
+ 0: disable, 1: enable
+ *supported since Cx
+
+ bit1 0 RW gesture ID output
+ 0: disable, 1: enable
+ *supported since Cx
+
+ bit2 0 RW two fingers' coordinates output
+ 0: disable, 1: enable
+ *supported since Cx
+
+ bit3 0 RW finger up one packet output
+ 0: disable, 1: enable
+ *supported since Cx
+
+ bit4 0 RW absolute coordination continuous mode
+ 0: disable, 1: enable
+ *supported since Cx
+
+ bit6~bit5 00 RW gesture group selection
+ 00: basic
+ 01: suite
+ 10: suite pro
+ 11: advanced
+ *supported since Cx
+
+ bit7 0 RW Bx packet output compatible mode
+ 0: disable, 1: enable *supported since Cx
+ *supported since Cx
+
+
+0x833d RW on-pad command control 1
+ bit7 1 RW on-pad command detection enable
+ 0: disable, 1: enable
+ *supported since Cx
+
+0x833e RW on-pad command detection
+ bit7 0 RW on-pad command left button down tag
+ enable. Works only in H/W based PS/2
+ data packet mode.
+ 0: disable, 1: enable
+ *supported since Cx
generated by cgit v1.2.3 (git 2.25.1) at 2024-04-18 15:22:36 +0000