1 files changed, 541 insertions, 42 deletions

diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index 1d333497cfc..8e820ddf4e0 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -22,9 +22,12 @@
 #include <linux/omap-dma.h>
 #include <linux/io.h>
 #include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
 
 #ifdef CONFIG_MTD_NAND_OMAP_BCH
 #include <linux/bch.h>
+#include <linux/platform_data/elm.h>
 #endif
 
 #include <linux/platform_data/mtd-nand-omap2.h>
@@ -117,6 +120,33 @@
 
 #define OMAP24XX_DMA_GPMC		4
 
+#define BCH8_MAX_ERROR		8	/* upto 8 bit correctable */
+#define BCH4_MAX_ERROR		4	/* upto 4 bit correctable */
+
+#define SECTOR_BYTES		512
+/* 4 bit padding to make byte aligned, 56 = 52 + 4 */
+#define BCH4_BIT_PAD		4
+#define BCH8_ECC_MAX		((SECTOR_BYTES + BCH8_ECC_OOB_BYTES) * 8)
+#define BCH4_ECC_MAX		((SECTOR_BYTES + BCH4_ECC_OOB_BYTES) * 8)
+
+/* GPMC ecc engine settings for read */
+#define BCH_WRAPMODE_1		1	/* BCH wrap mode 1 */
+#define BCH8R_ECC_SIZE0		0x1a	/* ecc_size0 = 26 */
+#define BCH8R_ECC_SIZE1		0x2	/* ecc_size1 = 2 */
+#define BCH4R_ECC_SIZE0		0xd	/* ecc_size0 = 13 */
+#define BCH4R_ECC_SIZE1		0x3	/* ecc_size1 = 3 */
+
+/* GPMC ecc engine settings for write */
+#define BCH_WRAPMODE_6		6	/* BCH wrap mode 6 */
+#define BCH_ECC_SIZE0		0x0	/* ecc_size0 = 0, no oob protection */
+#define BCH_ECC_SIZE1		0x20	/* ecc_size1 = 32 */
+
+#ifdef CONFIG_MTD_NAND_OMAP_BCH
+static u_char bch8_vector[] = {0xf3, 0xdb, 0x14, 0x16, 0x8b, 0xd2, 0xbe, 0xcc,
+	0xac, 0x6b, 0xff, 0x99, 0x7b};
+static u_char bch4_vector[] = {0x00, 0x6b, 0x31, 0xdd, 0x41, 0xbc, 0x10};
+#endif
+
 /* oob info generated runtime depending on ecc algorithm and layout selected */
 static struct nand_ecclayout omap_oobinfo;
 /* Define some generic bad / good block scan pattern which are used
@@ -156,6 +186,9 @@ struct omap_nand_info {
 #ifdef CONFIG_MTD_NAND_OMAP_BCH
 	struct bch_control             *bch;
 	struct nand_ecclayout           ecclayout;
+	bool				is_elm_used;
+	struct device			*elm_dev;
+	struct device_node		*of_node;
 #endif
 };
 
@@ -1031,6 +1064,13 @@ static int omap_dev_ready(struct mtd_info *mtd)
  * omap3_enable_hwecc_bch - Program OMAP3 GPMC to perform BCH ECC correction
  * @mtd: MTD device structure
  * @mode: Read/Write mode
+ *
+ * When using BCH, sector size is hardcoded to 512 bytes.
+ * Using wrapping mode 6 both for reading and writing if ELM module not uses
+ * for error correction.
+ * On writing,
+ * eccsize0 = 0  (no additional protected byte in spare area)
+ * eccsize1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area)
  */
 static void omap3_enable_hwecc_bch(struct mtd_info *mtd, int mode)
 {
@@ -1039,32 +1079,57 @@ static void omap3_enable_hwecc_bch(struct mtd_info *mtd, int mode)
 	struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
 						   mtd);
 	struct nand_chip *chip = mtd->priv;
-	u32 val;
+	u32 val, wr_mode;
+	unsigned int ecc_size1, ecc_size0;
+
+	/* Using wrapping mode 6 for writing */
+	wr_mode = BCH_WRAPMODE_6;
 
-	nerrors = (info->nand.ecc.bytes == 13) ? 8 : 4;
-	dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0;
-	nsectors = 1;
 	/*
-	 * Program GPMC to perform correction on one 512-byte sector at a time.
-	 * Using 4 sectors at a time (i.e. ecc.size = 2048) is also possible and
-	 * gives a slight (5%) performance gain (but requires additional code).
+	 * ECC engine enabled for valid ecc_size0 nibbles
+	 * and disabled for ecc_size1 nibbles.
 	 */
+	ecc_size0 = BCH_ECC_SIZE0;
+	ecc_size1 = BCH_ECC_SIZE1;
+
+	/* Perform ecc calculation on 512-byte sector */
+	nsectors = 1;
+
+	/* Update number of error correction */
+	nerrors = info->nand.ecc.strength;
+
+	/* Multi sector reading/writing for NAND flash with page size < 4096 */
+	if (info->is_elm_used && (mtd->writesize <= 4096)) {
+		if (mode == NAND_ECC_READ) {
+			/* Using wrapping mode 1 for reading */
+			wr_mode = BCH_WRAPMODE_1;
+
+			/*
+			 * ECC engine enabled for ecc_size0 nibbles
+			 * and disabled for ecc_size1 nibbles.
+			 */
+			ecc_size0 = (nerrors == 8) ?
+				BCH8R_ECC_SIZE0 : BCH4R_ECC_SIZE0;
+			ecc_size1 = (nerrors == 8) ?
+				BCH8R_ECC_SIZE1 : BCH4R_ECC_SIZE1;
+		}
+
+		/* Perform ecc calculation for one page (< 4096) */
+		nsectors = info->nand.ecc.steps;
+	}
 
 	writel(ECC1, info->reg.gpmc_ecc_control);
 
-	/*
-	 * When using BCH, sector size is hardcoded to 512 bytes.
-	 * Here we are using wrapping mode 6 both for reading and writing, with:
-	 *  size0 = 0  (no additional protected byte in spare area)
-	 *  size1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area)
-	 */
-	val = (32 << ECCSIZE1_SHIFT) | (0 << ECCSIZE0_SHIFT);
+	/* Configure ecc size for BCH */
+	val = (ecc_size1 << ECCSIZE1_SHIFT) | (ecc_size0 << ECCSIZE0_SHIFT);
 	writel(val, info->reg.gpmc_ecc_size_config);
 
+	dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0;
+
 	/* BCH configuration */
 	val = ((1                        << 16) | /* enable BCH */
 	       (((nerrors == 8) ? 1 : 0) << 12) | /* 8 or 4 bits */
-	       (0x06                     <<  8) | /* wrap mode = 6 */
+	       (wr_mode                  <<  8) | /* wrap mode */
 	       (dev_width                <<  7) | /* bus width */
 	       (((nsectors-1) & 0x7)     <<  4) | /* number of sectors */
 	       (info->gpmc_cs            <<  1) | /* ECC CS */
@@ -1072,7 +1137,7 @@ static void omap3_enable_hwecc_bch(struct mtd_info *mtd, int mode)
 
 	writel(val, info->reg.gpmc_ecc_config);
 
-	/* clear ecc and enable bits */
+	/* Clear ecc and enable bits */
 	writel(ECCCLEAR | ECC1, info->reg.gpmc_ecc_control);
 }
 
@@ -1162,6 +1227,298 @@ static int omap3_calculate_ecc_bch8(struct mtd_info *mtd, const u_char *dat,
 }
 
 /**
+ * omap3_calculate_ecc_bch - Generate bytes of ECC bytes
+ * @mtd:	MTD device structure
+ * @dat:	The pointer to data on which ecc is computed
+ * @ecc_code:	The ecc_code buffer
+ *
+ * Support calculating of BCH4/8 ecc vectors for the page
+ */
+static int omap3_calculate_ecc_bch(struct mtd_info *mtd, const u_char *dat,
+				    u_char *ecc_code)
+{
+	struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
+						   mtd);
+	unsigned long nsectors, bch_val1, bch_val2, bch_val3, bch_val4;
+	int i, eccbchtsel;
+
+	nsectors = ((readl(info->reg.gpmc_ecc_config) >> 4) & 0x7) + 1;
+	/*
+	 * find BCH scheme used
+	 * 0 -> BCH4
+	 * 1 -> BCH8
+	 */
+	eccbchtsel = ((readl(info->reg.gpmc_ecc_config) >> 12) & 0x3);
+
+	for (i = 0; i < nsectors; i++) {
+
+		/* Read hw-computed remainder */
+		bch_val1 = readl(info->reg.gpmc_bch_result0[i]);
+		bch_val2 = readl(info->reg.gpmc_bch_result1[i]);
+		if (eccbchtsel) {
+			bch_val3 = readl(info->reg.gpmc_bch_result2[i]);
+			bch_val4 = readl(info->reg.gpmc_bch_result3[i]);
+		}
+
+		if (eccbchtsel) {
+			/* BCH8 ecc scheme */
+			*ecc_code++ = (bch_val4 & 0xFF);
+			*ecc_code++ = ((bch_val3 >> 24) & 0xFF);
+			*ecc_code++ = ((bch_val3 >> 16) & 0xFF);
+			*ecc_code++ = ((bch_val3 >> 8) & 0xFF);
+			*ecc_code++ = (bch_val3 & 0xFF);
+			*ecc_code++ = ((bch_val2 >> 24) & 0xFF);
+			*ecc_code++ = ((bch_val2 >> 16) & 0xFF);
+			*ecc_code++ = ((bch_val2 >> 8) & 0xFF);
+			*ecc_code++ = (bch_val2 & 0xFF);
+			*ecc_code++ = ((bch_val1 >> 24) & 0xFF);
+			*ecc_code++ = ((bch_val1 >> 16) & 0xFF);
+			*ecc_code++ = ((bch_val1 >> 8) & 0xFF);
+			*ecc_code++ = (bch_val1 & 0xFF);
+			/*
+			 * Setting 14th byte to zero to handle
+			 * erased page & maintain compatibility
+			 * with RBL
+			 */
+			*ecc_code++ = 0x0;
+		} else {
+			/* BCH4 ecc scheme */
+			*ecc_code++ = ((bch_val2 >> 12) & 0xFF);
+			*ecc_code++ = ((bch_val2 >> 4) & 0xFF);
+			*ecc_code++ = ((bch_val2 & 0xF) << 4) |
+				((bch_val1 >> 28) & 0xF);
+			*ecc_code++ = ((bch_val1 >> 20) & 0xFF);
+			*ecc_code++ = ((bch_val1 >> 12) & 0xFF);
+			*ecc_code++ = ((bch_val1 >> 4) & 0xFF);
+			*ecc_code++ = ((bch_val1 & 0xF) << 4);
+			/*
+			 * Setting 8th byte to zero to handle
+			 * erased page
+			 */
+			*ecc_code++ = 0x0;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * erased_sector_bitflips - count bit flips
+ * @data:	data sector buffer
+ * @oob:	oob buffer
+ * @info:	omap_nand_info
+ *
+ * Check the bit flips in erased page falls below correctable level.
+ * If falls below, report the page as erased with correctable bit
+ * flip, else report as uncorrectable page.
+ */
+static int erased_sector_bitflips(u_char *data, u_char *oob,
+		struct omap_nand_info *info)
+{
+	int flip_bits = 0, i;
+
+	for (i = 0; i < info->nand.ecc.size; i++) {
+		flip_bits += hweight8(~data[i]);
+		if (flip_bits > info->nand.ecc.strength)
+			return 0;
+	}
+
+	for (i = 0; i < info->nand.ecc.bytes - 1; i++) {
+		flip_bits += hweight8(~oob[i]);
+		if (flip_bits > info->nand.ecc.strength)
+			return 0;
+	}
+
+	/*
+	 * Bit flips falls in correctable level.
+	 * Fill data area with 0xFF
+	 */
+	if (flip_bits) {
+		memset(data, 0xFF, info->nand.ecc.size);
+		memset(oob, 0xFF, info->nand.ecc.bytes);
+	}
+
+	return flip_bits;
+}
+
+/**
+ * omap_elm_correct_data - corrects page data area in case error reported
+ * @mtd:	MTD device structure
+ * @data:	page data
+ * @read_ecc:	ecc read from nand flash
+ * @calc_ecc:	ecc read from HW ECC registers
+ *
+ * Calculated ecc vector reported as zero in case of non-error pages.
+ * In case of error/erased pages non-zero error vector is reported.
+ * In case of non-zero ecc vector, check read_ecc at fixed offset
+ * (x = 13/7 in case of BCH8/4 == 0) to find page programmed or not.
+ * To handle bit flips in this data, count the number of 0's in
+ * read_ecc[x] and check if it greater than 4. If it is less, it is
+ * programmed page, else erased page.
+ *
+ * 1. If page is erased, check with standard ecc vector (ecc vector
+ * for erased page to find any bit flip). If check fails, bit flip
+ * is present in erased page. Count the bit flips in erased page and
+ * if it falls under correctable level, report page with 0xFF and
+ * update the correctable bit information.
+ * 2. If error is reported on programmed page, update elm error
+ * vector and correct the page with ELM error correction routine.
+ *
+ */
+static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data,
+				u_char *read_ecc, u_char *calc_ecc)
+{
+	struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
+			mtd);
+	int eccsteps = info->nand.ecc.steps;
+	int i , j, stat = 0;
+	int eccsize, eccflag, ecc_vector_size;
+	struct elm_errorvec err_vec[ERROR_VECTOR_MAX];
+	u_char *ecc_vec = calc_ecc;
+	u_char *spare_ecc = read_ecc;
+	u_char *erased_ecc_vec;
+	enum bch_ecc type;
+	bool is_error_reported = false;
+
+	/* Initialize elm error vector to zero */
+	memset(err_vec, 0, sizeof(err_vec));
+
+	if (info->nand.ecc.strength == BCH8_MAX_ERROR) {
+		type = BCH8_ECC;
+		erased_ecc_vec = bch8_vector;
+	} else {
+		type = BCH4_ECC;
+		erased_ecc_vec = bch4_vector;
+	}
+
+	ecc_vector_size = info->nand.ecc.bytes;
+
+	/*
+	 * Remove extra byte padding for BCH8 RBL
+	 * compatibility and erased page handling
+	 */
+	eccsize = ecc_vector_size - 1;
+
+	for (i = 0; i < eccsteps ; i++) {
+		eccflag = 0;	/* initialize eccflag */
+
+		/*
+		 * Check any error reported,
+		 * In case of error, non zero ecc reported.
+		 */
+
+		for (j = 0; (j < eccsize); j++) {
+			if (calc_ecc[j] != 0) {
+				eccflag = 1; /* non zero ecc, error present */
+				break;
+			}
+		}
+
+		if (eccflag == 1) {
+			/*
+			 * Set threshold to minimum of 4, half of ecc.strength/2
+			 * to allow max bit flip in byte to 4
+			 */
+			unsigned int threshold = min_t(unsigned int, 4,
+					info->nand.ecc.strength / 2);
+
+			/*
+			 * Check data area is programmed by counting
+			 * number of 0's at fixed offset in spare area.
+			 * Checking count of 0's against threshold.
+			 * In case programmed page expects at least threshold
+			 * zeros in byte.
+			 * If zeros are less than threshold for programmed page/
+			 * zeros are more than threshold erased page, either
+			 * case page reported as uncorrectable.
+			 */
+			if (hweight8(~read_ecc[eccsize]) >= threshold) {
+				/*
+				 * Update elm error vector as
+				 * data area is programmed
+				 */
+				err_vec[i].error_reported = true;
+				is_error_reported = true;
+			} else {
+				/* Error reported in erased page */
+				int bitflip_count;
+				u_char *buf = &data[info->nand.ecc.size * i];
+
+				if (memcmp(calc_ecc, erased_ecc_vec, eccsize)) {
+					bitflip_count = erased_sector_bitflips(
+							buf, read_ecc, info);
+
+					if (bitflip_count)
+						stat += bitflip_count;
+					else
+						return -EINVAL;
+				}
+			}
+		}
+
+		/* Update the ecc vector */
+		calc_ecc += ecc_vector_size;
+		read_ecc += ecc_vector_size;
+	}
+
+	/* Check if any error reported */
+	if (!is_error_reported)
+		return 0;
+
+	/* Decode BCH error using ELM module */
+	elm_decode_bch_error_page(info->elm_dev, ecc_vec, err_vec);
+
+	for (i = 0; i < eccsteps; i++) {
+		if (err_vec[i].error_reported) {
+			for (j = 0; j < err_vec[i].error_count; j++) {
+				u32 bit_pos, byte_pos, error_max, pos;
+
+				if (type == BCH8_ECC)
+					error_max = BCH8_ECC_MAX;
+				else
+					error_max = BCH4_ECC_MAX;
+
+				if (info->nand.ecc.strength == BCH8_MAX_ERROR)
+					pos = err_vec[i].error_loc[j];
+				else
+					/* Add 4 to take care 4 bit padding */
+					pos = err_vec[i].error_loc[j] +
+						BCH4_BIT_PAD;
+
+				/* Calculate bit position of error */
+				bit_pos = pos % 8;
+
+				/* Calculate byte position of error */
+				byte_pos = (error_max - pos - 1) / 8;
+
+				if (pos < error_max) {
+					if (byte_pos < 512)
+						data[byte_pos] ^= 1 << bit_pos;
+					else
+						spare_ecc[byte_pos - 512] ^=
+							1 << bit_pos;
+				}
+				/* else, not interested to correct ecc */
+			}
+		}
+
+		/* Update number of correctable errors */
+		stat += err_vec[i].error_count;
+
+		/* Update page data with sector size */
+		data += info->nand.ecc.size;
+		spare_ecc += ecc_vector_size;
+	}
+
+	for (i = 0; i < eccsteps; i++)
+		/* Return error if uncorrectable error present */
+		if (err_vec[i].error_uncorrectable)
+			return -EINVAL;
+
+	return stat;
+}
+
+/**
  * omap3_correct_data_bch - Decode received data and correct errors
  * @mtd: MTD device structure
  * @data: page data
@@ -1194,6 +1551,92 @@ static int omap3_correct_data_bch(struct mtd_info *mtd, u_char *data,
 }
 
 /**
+ * omap_write_page_bch - BCH ecc based write page function for entire page
+ * @mtd:		mtd info structure
+ * @chip:		nand chip info structure
+ * @buf:		data buffer
+ * @oob_required:	must write chip->oob_poi to OOB
+ *
+ * Custom write page method evolved to support multi sector writing in one shot
+ */
+static int omap_write_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
+				  const uint8_t *buf, int oob_required)
+{
+	int i;
+	uint8_t *ecc_calc = chip->buffers->ecccalc;
+	uint32_t *eccpos = chip->ecc.layout->eccpos;
+
+	/* Enable GPMC ecc engine */
+	chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
+
+	/* Write data */
+	chip->write_buf(mtd, buf, mtd->writesize);
+
+	/* Update ecc vector from GPMC result registers */
+	chip->ecc.calculate(mtd, buf, &ecc_calc[0]);
+
+	for (i = 0; i < chip->ecc.total; i++)
+		chip->oob_poi[eccpos[i]] = ecc_calc[i];
+
+	/* Write ecc vector to OOB area */
+	chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+	return 0;
+}
+
+/**
+ * omap_read_page_bch - BCH ecc based page read function for entire page
+ * @mtd:		mtd info structure
+ * @chip:		nand chip info structure
+ * @buf:		buffer to store read data
+ * @oob_required:	caller requires OOB data read to chip->oob_poi
+ * @page:		page number to read
+ *
+ * For BCH ecc scheme, GPMC used for syndrome calculation and ELM module
+ * used for error correction.
+ * Custom method evolved to support ELM error correction & multi sector
+ * reading. On reading page data area is read along with OOB data with
+ * ecc engine enabled. ecc vector updated after read of OOB data.
+ * For non error pages ecc vector reported as zero.
+ */
+static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
+				uint8_t *buf, int oob_required, int page)
+{
+	uint8_t *ecc_calc = chip->buffers->ecccalc;
+	uint8_t *ecc_code = chip->buffers->ecccode;
+	uint32_t *eccpos = chip->ecc.layout->eccpos;
+	uint8_t *oob = &chip->oob_poi[eccpos[0]];
+	uint32_t oob_pos = mtd->writesize + chip->ecc.layout->eccpos[0];
+	int stat;
+	unsigned int max_bitflips = 0;
+
+	/* Enable GPMC ecc engine */
+	chip->ecc.hwctl(mtd, NAND_ECC_READ);
+
+	/* Read data */
+	chip->read_buf(mtd, buf, mtd->writesize);
+
+	/* Read oob bytes */
+	chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, -1);
+	chip->read_buf(mtd, oob, chip->ecc.total);
+
+	/* Calculate ecc bytes */
+	chip->ecc.calculate(mtd, buf, ecc_calc);
+
+	memcpy(ecc_code, &chip->oob_poi[eccpos[0]], chip->ecc.total);
+
+	stat = chip->ecc.correct(mtd, buf, ecc_code, ecc_calc);
+
+	if (stat < 0) {
+		mtd->ecc_stats.failed++;
+	} else {
+		mtd->ecc_stats.corrected += stat;
+		max_bitflips = max_t(unsigned int, max_bitflips, stat);
+	}
+
+	return max_bitflips;
+}
+
+/**
  * omap3_free_bch - Release BCH ecc resources
  * @mtd: MTD device structure
  */
@@ -1218,43 +1661,86 @@ static int omap3_init_bch(struct mtd_info *mtd, int ecc_opt)
 	struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
 						   mtd);
 #ifdef CONFIG_MTD_NAND_OMAP_BCH8
-	const int hw_errors = 8;
+	const int hw_errors = BCH8_MAX_ERROR;
 #else
-	const int hw_errors = 4;
+	const int hw_errors = BCH4_MAX_ERROR;
 #endif
+	enum bch_ecc bch_type;
+	const __be32 *parp;
+	int lenp;
+	struct device_node *elm_node;
+
 	info->bch = NULL;
 
-	max_errors = (ecc_opt == OMAP_ECC_BCH8_CODE_HW) ? 8 : 4;
+	max_errors = (ecc_opt == OMAP_ECC_BCH8_CODE_HW) ?
+		BCH8_MAX_ERROR : BCH4_MAX_ERROR;
 	if (max_errors != hw_errors) {
 		pr_err("cannot configure %d-bit BCH ecc, only %d-bit supported",
 		       max_errors, hw_errors);
 		goto fail;
 	}
 
-	/* software bch library is only used to detect and locate errors */
-	info->bch = init_bch(13, max_errors, 0x201b /* hw polynomial */);
-	if (!info->bch)
-		goto fail;
+	info->nand.ecc.size = 512;
+	info->nand.ecc.hwctl = omap3_enable_hwecc_bch;
+	info->nand.ecc.mode = NAND_ECC_HW;
+	info->nand.ecc.strength = max_errors;
 
-	info->nand.ecc.size    = 512;
-	info->nand.ecc.hwctl   = omap3_enable_hwecc_bch;
-	info->nand.ecc.correct = omap3_correct_data_bch;
-	info->nand.ecc.mode    = NAND_ECC_HW;
+	if (hw_errors == BCH8_MAX_ERROR)
+		bch_type = BCH8_ECC;
+	else
+		bch_type = BCH4_ECC;
 
-	/*
-	 * The number of corrected errors in an ecc block that will trigger
-	 * block scrubbing defaults to the ecc strength (4 or 8).
-	 * Set mtd->bitflip_threshold here to define a custom threshold.
-	 */
+	/* Detect availability of ELM module */
+	parp = of_get_property(info->of_node, "elm_id", &lenp);
+	if ((parp == NULL) && (lenp != (sizeof(void *) * 2))) {
+		pr_err("Missing elm_id property, fall back to Software BCH\n");
+		info->is_elm_used = false;
+	} else {
+		struct platform_device *pdev;
 
-	if (max_errors == 8) {
-		info->nand.ecc.strength  = 8;
-		info->nand.ecc.bytes     = 13;
-		info->nand.ecc.calculate = omap3_calculate_ecc_bch8;
+		elm_node = of_find_node_by_phandle(be32_to_cpup(parp));
+		pdev = of_find_device_by_node(elm_node);
+		info->elm_dev = &pdev->dev;
+		elm_config(info->elm_dev, bch_type);
+		info->is_elm_used = true;
+	}
+
+	if (info->is_elm_used && (mtd->writesize <= 4096)) {
+
+		if (hw_errors == BCH8_MAX_ERROR)
+			info->nand.ecc.bytes = BCH8_SIZE;
+		else
+			info->nand.ecc.bytes = BCH4_SIZE;
+
+		info->nand.ecc.correct = omap_elm_correct_data;
+		info->nand.ecc.calculate = omap3_calculate_ecc_bch;
+		info->nand.ecc.read_page = omap_read_page_bch;
+		info->nand.ecc.write_page = omap_write_page_bch;
 	} else {
-		info->nand.ecc.strength  = 4;
-		info->nand.ecc.bytes     = 7;
-		info->nand.ecc.calculate = omap3_calculate_ecc_bch4;
+		/*
+		 * software bch library is only used to detect and
+		 * locate errors
+		 */
+		info->bch = init_bch(13, max_errors,
+				0x201b /* hw polynomial */);
+		if (!info->bch)
+			goto fail;
+
+		info->nand.ecc.correct = omap3_correct_data_bch;
+
+		/*
+		 * The number of corrected errors in an ecc block that will
+		 * trigger block scrubbing defaults to the ecc strength (4 or 8)
+		 * Set mtd->bitflip_threshold here to define a custom threshold.
+		 */
+
+		if (max_errors == 8) {
+			info->nand.ecc.bytes = 13;
+			info->nand.ecc.calculate = omap3_calculate_ecc_bch8;
+		} else {
+			info->nand.ecc.bytes = 7;
+			info->nand.ecc.calculate = omap3_calculate_ecc_bch4;
+		}
 	}
 
 	pr_info("enabling NAND BCH ecc with %d-bit correction\n", max_errors);
@@ -1270,7 +1756,7 @@ fail:
  */
 static int omap3_init_bch_tail(struct mtd_info *mtd)
 {
-	int i, steps;
+	int i, steps, offset;
 	struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
 						   mtd);
 	struct nand_ecclayout *layout = &info->ecclayout;
@@ -1292,11 +1778,21 @@ static int omap3_init_bch_tail(struct mtd_info *mtd)
 		goto fail;
 	}
 
+	/* ECC layout compatible with RBL for BCH8 */
+	if (info->is_elm_used && (info->nand.ecc.bytes == BCH8_SIZE))
+		offset = 2;
+	else
+		offset = mtd->oobsize - layout->eccbytes;
+
 	/* put ecc bytes at oob tail */
 	for (i = 0; i < layout->eccbytes; i++)
-		layout->eccpos[i] = mtd->oobsize-layout->eccbytes+i;
+		layout->eccpos[i] = offset + i;
+
+	if (info->is_elm_used && (info->nand.ecc.bytes == BCH8_SIZE))
+		layout->oobfree[0].offset = 2 + layout->eccbytes * steps;
+	else
+		layout->oobfree[0].offset = 2;
 
-	layout->oobfree[0].offset = 2;
 	layout->oobfree[0].length = mtd->oobsize-2-layout->eccbytes;
 	info->nand.ecc.layout = layout;
 
@@ -1360,6 +1856,9 @@ static int omap_nand_probe(struct platform_device *pdev)
 
 	info->nand.options	= pdata->devsize;
 	info->nand.options	|= NAND_SKIP_BBTSCAN;
+#ifdef CONFIG_MTD_NAND_OMAP_BCH
+	info->of_node		= pdata->of_node;
+#endif
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (res == NULL) {