| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Set-associative caches on all v7 implementations map the index bits
to physical addresses LSBs and tag bits to MSBs. As the last level
of cache on current and upcoming ARM systems grows in size,
this means that under normal DRAM controller configurations, the
current v7 cache flush routine using set/way operations triggers a
DRAM memory controller precharge/activate for every cache line
writeback since the cache routine cleans lines by first fixing the
index and then looping through ways (index bits are mapped to lower
physical addresses on all v7 cache implementations; this means that,
with last level cache sizes in the order of MBytes, lines belonging
to the same set but different ways map to different DRAM pages).
Given the random content of cache tags, swapping the order between
indexes and ways loops do not prevent DRAM pages precharge and
activate cycles but at least, on average, improves the chances that
either multiple lines hit the same page or multiple lines belong to
different DRAM banks, improving throughput significantly.
This patch swaps the inner loops in the v7 cache flushing routine
to carry out the clean operations first on all sets belonging to
a given way (looping through sets) and then decrementing the way.
Benchmarks showed that by swapping the ordering in which sets and
ways are decremented in the v7 cache flushing routine, that uses
set/way operations, time required to flush caches is reduced
significantly, owing to improved writebacks throughput to the DRAM
controller.
Benchmarks results vary and depend heavily on the last level of
cache tag RAM content when cache is cleaned and invalidated, ranging
from 2x throughput when all tag RAM entries contain dirty lines
mapping to sequential pages of RAM to 1x (ie no improvement) when
all tag RAM accesses trigger a DRAM precharge/activate cycle, as the
current code implies on most DRAM controller configurations.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(cherry picked from commit 70f665fe77c54740d0fa8aaad5de2181d75af15e)
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
lsk-v3.10-big.LITTLE
Conflicts:
kernel/irq/irqdesc.c
linaro/configs/big-LITTLE-MP.conf
|
|
This reverts commit f0862cb749c537c32de82912d30110098ddc6cd6. Analysis
from Vincent Guittot:
With the current implementation, the load average statistics of a sched entity
change according to other activity on the CPU even if this activity is done
between the running window of the sched entity and have no influence on the
running duration of the task.
When a task wakes up on the same CPU, we currently update last_runnable_update
with the return of __synchronize_entity_decay without updating the
runnable_avg_sum and runnable_avg_period accordingly. In fact, we have to sync
the load_contrib of the se with the rq's blocked_load_contrib before removing
it from the latter (with __synchronize_entity_decay) but we must keep
last_runnable_update unchanged for updating runnable_avg_sum/period during the
next update_entity_load_avg.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is an error scenario where on a 1x1 HMP system (weight of the
hmp_slow_cpu_mask is 1) the short-cut of restricting the allowed cpu mask
of an rt tasks leads to triggering a kernel bug in the rt sched class
set_cpus_allowed function set_cpus_allowed_rt().
In case the task is on the run-queue and the weight of the required cpu mask
is 1 and this is different to the p->nr_cpus_allowed value, this back-end
function interprets this in such a way that a task changed from being
migratable to not migratable anymore and decrements the rt_nr_migratory
counter. There is a BUG_ON(!rq->rt.rt_nr_migratory) check in this code
path which triggers in this situation.
To circumvent this issue, set the number of allowed cpus for a task p to
the weight of the hmp_slow_cpu_mask before calling do_set_cpus_allowed()
in __setscheduler(). It will be set to this value in do_set_cpus_allowed()
after the call to the sched class related backend function any way. By
doing this, set_cpus_allowed_rt() returns without trying to update the
rt_nr_migratory counter.
This patch has been tested with a test device driver requiring a threaded
irq handler on a TC2 system with a reduced cpu mask (1 Cortex A15, 1
Cortex A7).
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
This patch limits the default affinity mask for all irqs to the cluster of
the little cpus.
This patch has the positive side effect that an irq thread which has its
IRQTF_RUNTHREAD set inside irq_thread() -> irq_wait_for_interrupt() will
not overwrite its struct task_struct->cpus_allowed with a full cpu mask of
desc->irq_data.affinity in irq_thread_check_affinity() essentially reverting
patch "HMP: experimental: Force all rt tasks to start on little domain."
for this irq thread.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
We use get_task_struct to increment the ref count on a task_struct
so that even if the task dies with a pending migration we are still
able to read the memory without causing a fault.
In the case of non-running tasks, we forgot to decrement the ref
count when we are done with the task.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
The scheduler will default packing to disabled, but this includes the
feature so that we can test it more easily.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
Since TC2 power curves don't really have a utilisation hotspot where
packing makes sense, if it is present for a TC2 system at least make
it default to disabled.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
The presence of packing permanently changed the idle balance
behaviour. Do not restrict idle balance on the smallest CPUs when
packing is present but disabled.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
If we migrate a sleeping task away from a CPU which has the
tick stopped, then both the clock_task and decay_counter will
be out of date for that CPU and we will not decay load correctly
regardless of how often we update the blocked load.
This is only an issue for tasks which are not on a runqueue
(because otherwise that CPU would be awake) and simultaneously
the CPU the task previously ran on has had the tick stopped.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
If an entity happens to sleep for less than one tick duration
the tracked load associated with that entity can be decayed by an
unexpectedly large amount if it is later migrated to a different
CPU. This can interfere with correct scheduling when entity load
is used for decision making.
The reason for this is that when an entity is dequeued and enqueued
quickly, such that se.avg.decay_count and cfs_rq.decay_counter
do not differ when that entity is enqueued again,
__synchronize_entity_decay skips the calculation step and also skips
clearing the decay_count. At a later time that entity may be
migrated and its load will be decayed incorrectly.
All users of this function expect decay_count to be zero'ed after
use.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
If we isolate CPUs, then we don't want random device interrupts on
them. Even w/o the user space irq balancer enabled we can end up with
irqs on non boot cpus.
Allow to restrict the default irq affinity mask.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
This patch adds config fragments used to enable most of the features
used by big LITTLE MP.
This patch is the result of merging the following commits from the
Linaro Stable Kernel (LSK) 3.10 tree...
Commit 313c69010ed52a7bd52095708049e16c380c8e15
Commit 83952e566d1c41b2e0a70321e9d56cb8162f9a6d
Commit c4a782d985da03016e2b15aaef90bfc5cfe426f6
Commit 2732b0467a356e7cc08bf1e0f33481330335657a
Commit 7c88e2bd50fc093c96c912090b712b682ae72641
Commit 3231c8ce4b005f79ad27309907adc3de319e341c
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
At present we print per-entity load-tracking statistics for
cfs_rq of cgroups/runqueues. Given that per task statistics
is maintained, it can be used to know the contribution made
by the task to its parenting cfs_rq level.
This patch adds per-task load-tracking statistics to /proc/<PID>/sched.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20130625080336.GA20175@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
(cherry picked from commit 939fd731eb88a0cdd9058d0b0143563172a217d7)
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
|
|
|
|
|
|
commit 0ac9b1c21874d2490331233b3242085f8151e166 upstream.
Currently, group entity load-weights are initialized to zero. This
admits some races with respect to the first time they are re-weighted in
earlty use. ( Let g[x] denote the se for "g" on cpu "x". )
Suppose that we have root->a and that a enters a throttled state,
immediately followed by a[0]->t1 (the only task running on cpu[0])
blocking:
put_prev_task(group_cfs_rq(a[0]), t1)
put_prev_entity(..., t1)
check_cfs_rq_runtime(group_cfs_rq(a[0]))
throttle_cfs_rq(group_cfs_rq(a[0]))
Then, before unthrottling occurs, let a[0]->b[0]->t2 wake for the first
time:
enqueue_task_fair(rq[0], t2)
enqueue_entity(group_cfs_rq(b[0]), t2)
enqueue_entity_load_avg(group_cfs_rq(b[0]), t2)
account_entity_enqueue(group_cfs_ra(b[0]), t2)
update_cfs_shares(group_cfs_rq(b[0]))
< skipped because b is part of a throttled hierarchy >
enqueue_entity(group_cfs_rq(a[0]), b[0])
...
We now have b[0] enqueued, yet group_cfs_rq(a[0])->load.weight == 0
which violates invariants in several code-paths. Eliminate the
possibility of this by initializing group entity weight.
Signed-off-by: Paul Turner <pjt@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20131016181627.22647.47543.stgit@sword-of-the-dawn.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 927b54fccbf04207ec92f669dce6806848cbec7d upstream.
__start_cfs_bandwidth calls hrtimer_cancel while holding rq->lock,
waiting for the hrtimer to finish. However, if sched_cfs_period_timer
runs for another loop iteration, the hrtimer can attempt to take
rq->lock, resulting in deadlock.
Fix this by ensuring that cfs_b->timer_active is cleared only if the
_latest_ call to do_sched_cfs_period_timer is returning as idle. Then
__start_cfs_bandwidth can just call hrtimer_try_to_cancel and wait for
that to succeed or timer_active == 1.
Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: pjt@google.com
Link: http://lkml.kernel.org/r/20131016181622.22647.16643.stgit@sword-of-the-dawn.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db06e78cc13d70f10877e0557becc88ab3ad2be8 upstream.
hrtimer_expires_remaining does not take internal hrtimer locks and thus
must be guarded against concurrent __hrtimer_start_range_ns (but
returning HRTIMER_RESTART is safe). Use cfs_b->lock to make it safe.
Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: pjt@google.com
Link: http://lkml.kernel.org/r/20131016181617.22647.73829.stgit@sword-of-the-dawn.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ee14e6c8cddeeb8a490d7b54cd9016e4bb900b4 upstream.
When we transition cfs_bandwidth_used to false, any currently
throttled groups will incorrectly return false from cfs_rq_throttled.
While tg_set_cfs_bandwidth will unthrottle them eventually, currently
running code (including at least dequeue_task_fair and
distribute_cfs_runtime) will cause errors.
Fix this by turning off cfs_bandwidth_used only after unthrottling all
cfs_rqs.
Tested: toggle bandwidth back and forth on a loaded cgroup. Caused
crashes in minutes without the patch, hasn't crashed with it.
Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: pjt@google.com
Link: http://lkml.kernel.org/r/20131016181611.22647.80365.stgit@sword-of-the-dawn.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26bef1318adc1b3a530ecc807ef99346db2aa8b0 upstream.
Before we do an EMMS in the AMD FXSAVE information leak workaround we
need to clear any pending exceptions, otherwise we trap with a
floating-point exception inside this code.
Reported-by: halfdog <me@halfdog.net>
Tested-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/CA%2B55aFxQnY_PCG_n4=0w-VG=YLXL-yr7oMxyy0WU2gCBAf3ydg@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2690d97ade05c5325cbf7c72b94b90d265659886 upstream.
Commit 5901b6be885e attempted to introduce IPv6 support into
IRC NAT helper. By doing so, the following code seemed to be removed
by accident:
ip = ntohl(exp->master->tuplehash[IP_CT_DIR_REPLY].tuple.dst.u3.ip);
sprintf(buffer, "%u %u", ip, port);
pr_debug("nf_nat_irc: inserting '%s' == %pI4, port %u\n", buffer, &ip, port);
This leads to the fact that buffer[] was left uninitialized and
contained some stack value. When we call nf_nat_mangle_tcp_packet(),
we call strlen(buffer) on excatly this uninitialized buffer. If we
are unlucky and the skb has enough tailroom, we overwrite resp. leak
contents with values that sit on our stack into the packet and send
that out to the receiver.
Since the rather informal DCC spec [1] does not seem to specify
IPv6 support right now, we log such occurences so that admins can
act accordingly, and drop the packet. I've looked into XChat source,
and IPv6 is not supported there: addresses are in u32 and print
via %u format string.
Therefore, restore old behaviour as in IPv4, use snprintf(). The
IRC helper does not support IPv6 by now. By this, we can safely use
strlen(buffer) in nf_nat_mangle_tcp_packet() and prevent a buffer
overflow. Also simplify some code as we now have ct variable anyway.
[1] http://www.irchelp.org/irchelp/rfc/ctcpspec.html
Fixes: 5901b6be885e ("netfilter: nf_nat: support IPv6 in IRC NAT helper")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af73623f5f10eb3832c87a169b28f7df040a875b upstream.
Somehow older areca firmware versions have issues with
scsi_get_vpd_page() and a large buffer, the firmware
seems to crash and the scsi error-handler will start endless
recovery retries.
Limiting the buf-size to 64-bytes fixes this issue with older
firmware versions (<1.49 for my controller).
Fixes a regression with areca controllers and older firmware versions
introduced by commit: 66c28f97120e8a621afd5aa7a31c4b85c547d33d
Reported-by: Nix <nix@esperi.org.uk>
Tested-by: Nix <nix@esperi.org.uk>
Signed-off-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6cbd7ee10e2842a3d1f9b60abede1c8f3d1f1130 upstream.
KVM environments do not support APERF/MPERF MSRs. intel_pstate cannot
operate without these registers.
The previous validity checks in intel_pstate_msrs_not_valid() are
insufficent in nested KVMs.
References: https://bugzilla.redhat.com/show_bug.cgi?id=1046317
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 277d916fc2e959c3f106904116bb4f7b1148d47a upstream.
The check needs to apply to both multicast and unicast packets,
otherwise probe requests on AP mode scans are sent through the multicast
buffer queue, which adds long delays (often longer than the scanning
interval).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a90b40385735af0d3031f98e97b439e8944a31b3 upstream.
The AML method _BIX of NEC LZ750/LS returns a broken package which
skips the first member "Revision" (ACPI 5.0, Table 10-234).
Add a quirk for this machine to skip member "Revision" during parsing
the package returned by _BIX.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=67351
Reported-and-tested-by: Francisco Castro <fcr@adinet.com.uy>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit df45c712d1f4ef37714245fb75de726f4ca2bf8d upstream.
In function ppi_callback(), memory allocated by acpi_get_name() will get
leaked when current device isn't the desired TPM device, so fix the
memory leak.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73beb63d290f961c299526852884846b0d868840 upstream.
This fixes a kernel panic when resuming from suspend to RAM.
Without this fix an interrupt hits after the delayed work is canceled
and thus requeues it. So we end up freeing an armed timer.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97c3557c3e0413efb1f021f582d1459760e22727 upstream.
The gate clocks for the MFC sysmmus appear to be flipped, i.e.
GATE_IP_MFC[2] gates sysmmu_mfcl and GATE_IP_MFC[1] gates sysmmu_mfcr.
Fix this so that the MFC will start up.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2feed5aecf5f367b92bd6b6e92afe9e3de466907 upstream.
The sysreg (system register) generates control signals for various blocks
like disp1blk, i2c, mipi, usb etc. However, it gets disabled as an unused
clock at boot-up. This can lead to failures in operation of above blocks,
because they can not be configured properly if this clock is disabled.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5fdd1b56be51b1ec4dbde5b213d649ac717442da upstream.
The SRC_MFC register offset was incorrect, which could cause have caused
wrong calculation of rate of sclk_mfc clock, that could in turn lead to
incorrect operation of MFC. This patch corrects it.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 778037e1ccb75609846deca9e419449c1dc137fa upstream.
Commit 6d9252bd9a4bb (clk: Add support for power of two type dividers)
merged in v3.6 added the _get_val function to convert a divisor value to
a register field value depending on the flags. However it used the type
u8 for the div field, causing divisors larger than 255 to be masked
and the resultant clock rate to be too high.
E.g. in my case an 11bit divider was supposed to divide 24.576 MHz down
to 32.768KHz. The divisor was correctly calculated as 750 (0x2ee). This
was masked to 238 (0xee) resulting in a frequency of 103.26KHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e098f5cbe9d410e7878b50f524dce36cc83ec40e upstream.
This patch adds support for the PCI ID provided by the Marvell 88SE9170
SATA controller.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8dae00684d678afa13041ef170cecfd1297ed40 upstream.
Helge Deller noted a few weeks ago problems with the AIO support on
parisc. This change is the result of numerous iterations on how best to
deal with this problem.
The solution adopted here is to provide full cache coherency in a
uniform manner on all parisc systems. This involves calling
flush_dcache_page() on kmap operations and flush_kernel_dcache_page() on
kunmap operations. As a result, the copy_user_page() and
clear_user_page() functions can be removed and the overall code is
simpler.
The change ensures that both userspace and kernel aliases to a mapped
page are invalidated and flushed. This is necessary for the correct
operation of PA8800 and PA8900 based systems which do not support
inequivalent aliases.
With this change, I have observed no cache related issues on c8000 and
rp3440. It is now possible for example to do kernel builds with "-j64"
on four way systems.
On systems using XFS file systems, the patch recently posted by Mikulas
Patocka to "fix crash using XFS on loopback" is needed to avoid a hang
caused by an uninitialized lock passed to flush_dcache_page() in the
page struct.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d60792ec059d9f2139828f9f017679abb81aa73 upstream.
This fixes a hang in VBIOS scripts of the form "condition; jump".
The jump used to always be executed, while now it will only be
executed if the condition is true.
See https://bugs.freedesktop.org/show_bug.cgi?id=72943
Reported-by: Darcy Brás da Silva <dardevelin@cidadecool.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b6328a6b7ba57fc84c38248f6f0e387e1170f1a8 upstream.
Commit 4dcfa60071b3d23f0181f27d8519f12e37cefbb9 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcd740b645003b866d7eb30d13d34d0729cce9db upstream.
Commit 4dcfa60071b3d23f0181f27d8519f12e37cefbb9 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f387323853c495ac589210832fad4503f75a0e7 upstream.
Commit 4dcfa60071b3d23f0181f27d8519f12e37cefbb9 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8777539479abd7b3efeb691685415dc2b057d0e0 upstream.
Due to incorrect clock specified in MDMA0 node, using MDMA0 controller
could cause system failures, due to wrong clock being controlled. This
patch fixes this by specifying correct clock.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Corrected commit message and description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29c350bf28da333e41e30497b649fe335712a2ab upstream.
The array was missing the final entry for the undefined instruction
exception handler; this commit adds it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4ff859fe1dc0da0f87bbdfff78f527898878fa4a upstream.
The clockevents code was being told that the footbridge clock event
device ticks at 16x the rate which it actually does. This leads to
timekeeping problems since it allows the clocksource to wrap before
the kernel notices. Fix this by using the correct clock.
Fixes: 4e8d76373c9fd ("ARM: footbridge: convert to clockevents/clocksource")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1cdbcb7957cf9e5f841dbcde9b38fd18a804208b ]
This is a generic solution to resolve a specific problem that I have observed.
If the encapsulation of an skb changes then ability to offload checksums
may also change. In particular it may be necessary to perform checksumming
in software.
An example of such a case is where a non-GRE packet is received but
is to be encapsulated and transmitted as GRE.
Another example relates to my proposed support for for packets
that are non-MPLS when received but MPLS when transmitted.
The cost of this change is that the value of the csum variable may be
checked when it previously was not. In the case where the csum variable is
true this is pure overhead. In the case where the csum variable is false it
leads to software checksumming, which I believe also leads to correct
checksums in transmitted packets for the cases described above.
Further analysis:
This patch relies on the return value of can_checksum_protocol()
being correct and in turn the return value of skb_network_protocol(),
used to provide the protocol parameter of can_checksum_protocol(),
being correct. It also relies on the features passed to skb_segment()
and in turn to can_checksum_protocol() being correct.
I believe that this problem has not been observed for VLANs because it
appears that almost all drivers, the exception being xgbe, set
vlan_features such that that the checksum offload support for VLAN packets
is greater than or equal to that of non-VLAN packets.
I wonder if the code in xgbe may be an oversight and the hardware does
support checksumming of VLAN packets. If so it may be worth updating the
vlan_features of the driver as this patch will force such checksums to be
performed in software rather than hardware.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fe0d692bbc645786bce1a98439e548ae619269f5 ]
br_multicast_set_hash_max() is called from process context in
net/bridge/br_sysfs_br.c by the sysfs store_hash_max() function.
br_multicast_set_hash_max() calls spin_lock(&br->multicast_lock),
which can deadlock the CPU if a softirq that also tries to take the
same lock interrupts br_multicast_set_hash_max() while the lock is
held . This can happen quite easily when any of the bridge multicast
timers expire, which try to take the same lock.
The fix here is to use spin_lock_bh(), preventing other softirqs from
executing on this CPU.
Steps to reproduce:
1. Create a bridge with several interfaces (I used 4).
2. Set the "multicast query interval" to a low number, like 2.
3. Enable the bridge as a multicast querier.
4. Repeatedly set the bridge hash_max parameter via sysfs.
# brctl addbr br0
# brctl addif br0 eth1 eth2 eth3 eth4
# brctl setmcqi br0 2
# brctl setmcquerier br0 1
# while true ; do echo 4096 > /sys/class/net/br0/bridge/hash_max; done
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aca5f58f9ba803ec8c2e6bcf890db17589e8dfcc ]
The VLAN tag handling code in netpoll_send_skb_on_dev() has two problems.
1) It exits without unlocking the TXQ.
2) It then tries to queue a NULL skb to npinfo->txq.
Reported-by: Ahmed Tamrawi <atamrawi@iastate.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4d231b76eef6c4a6bd9c96769e191517765942cb ]
While commit 30a584d944fb fixes datagram interface in LLC, a use
after free bug has been introduced for SOCK_STREAM sockets that do
not make use of MSG_PEEK.
The flow is as follow ...
if (!(flags & MSG_PEEK)) {
...
sk_eat_skb(sk, skb, false);
...
}
...
if (used + offset < skb->len)
continue;
... where sk_eat_skb() calls __kfree_skb(). Therefore, cache
original length and work on skb_len to check partial reads.
Fixes: 30a584d944fb ("[LLX]: SOCK_DGRAM interface fixes")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6cd4ce0099da7702f885b6fa9ebb49e3831d90b4 ]
During restoring, try_fill_recv() was called with neither napi lock nor napi
disabled. This can lead two try_fill_recv() was called in the same time. Fix
this by refilling before trying to enable napi.
Fixes 0741bcb5584f9e2390ae6261573c4de8314999f2
(virtio: net: Add freeze, restore handlers to support S4).
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We leak an skb when there are too many frags,
we also stop processing the packet in the middle,
the result is almost sure to be loss of networking.
Reported-by: Michael Dalton <mwdalton@google.com>
Acked-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
