| Age | Commit message (Collapse) | Author |
|---|
|
The Kconfig options selected by ARCH_TEGRA_*_SOC were recently sorted.
Update the newly added ARCH_TEGRA_114_SOC's select statements to match.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
CONFIG_ARCH_TEGRA_114_SOC doesn't currently enable gpiolib, which causes
numerous build problems building a Tegra kernel with only Tegra114
enabled, and not Tegra20 or Tegra30. Enable ARCH_REQUIRE_GPIOLIB to
solve this. However, all Tegra will use gpiolib, so select this option
from ARCH_TEGRA rather than each individual ARCH_TEGRA_*_SOC, to
prevent this problem for any future chips.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Select PINCTRL and PINCTRL_TEGRA114 for enabling Tegra114 pincontrol
driver for Tegra114 SoC.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add new Tegra 114 SoC support.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The "powered-down" cpuidle mode of Tegra20 needs the CPU0 be the last one
core to go into this mode before other core. The coupled cpuidle framework
can help to sync the MPCore to coupled state then go into "powered-down"
idle mode together. The driver can just assume the MPCore come into
"powered-down" mode at the same time. No need to take care if the CPU_0
goes into this mode along and only can put it into safe idle mode (WFI).
The powered-down state of Tegra20 requires power gating both CPU cores.
When the secondary CPU requests to enter powered-down state, it saves
its own contexts and then enters WFI for waiting CPU0 in the same state.
When the CPU0 requests powered-down state, it attempts to put the secondary
CPU into reset to prevent it from waking up. Then power down both CPUs
together and power off the cpu rail.
Be aware of that, you may see the legacy power state "LP2" in the code
which is exactly the same meaning of "CPU power down".
Based on the work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Fix:
warning: (ARCH_TEGRA_2x_SOC) selects ARM_ERRATA_754327 which has unmet direct dependencies (CPU_V7 && SMP)
warning: (ARCH_TEGRA_2x_SOC) selects ARM_ERRATA_742230 which has unmet direct dependencies (CPU_V7 && SMP)
by selecting options only if SMP.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
|
|
Correct spelling typo within various Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move Tegra's debug-macro.S over to the common debug macro directory.
Move Tegra's debug UART selection menu into ARM's Kconfig.debug, so that
all related options are selected in the same place.
Tegra's uncompress.h is left in mach-tegra/include/mach; it will be
removed whenever Tegra is converted to multi-platform.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Delete CONFIG_TEGRA_DEBUG_UART_AUTO_SCRATCH; it's not useful any more:
* No upstream bootloader currently or will ever support this option.
* CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA is a much more direct alternative.
Merge the fixed and automatic UART selection menus into a single choice
for simplicity; now you either pick AUTO_ODMDATA or a single fixed UART,
rather than potentially having an AUTO option override whatever fixed
option was chosen.
Remove TEGRA_DEBUG_UART_NONE; if you don't want a Tegra DEBUG_LL UART,
simply don't turn on DEBUG_LL. NONE used to be the default option, so
pick AUTO_ODMDATA as the new default.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This is a series from Arnd that fixes a number of compiler warnings
when building defconfigs on ARM.
* late/fixes:
ARM: footbridge: nw_gpio_lock is raw_spin_lock
ARM: mv78xx0: correct addr_map_cfg __initdata annotation
ARM: footbridge: remove RTC_IRQ definition
ARM: soc: dependency warnings for errata
ARM: ks8695: __arch_virt_to_dma type handling
ARM: rpc: check device_register return code in ecard_probe
ARM: davinci: don't mark da850_register_cpufreq as __init
ARM: iop13xx: fix iq81340sc_atux_map_irq prototype
ARM: iop13xx: mark iop13xx_scan_bus as __devinit
ARM: mv78xx0: mark mv78xx0_timer_init as __init_refok
ARM: s3c24xx: fix multiple section mismatch warnings
ARM: at91: unused variable in at91_pm_verify_clocks
ARM: at91: skip at91_io_desc definition for NOMMU
ARM: pxa: work around duplicate definition of GPIO24_SSP1_SFRM
ARM: pxa: remove sharpsl_fatal_check function
ARM: pxa: define palmte2_pxa_keys conditionally
ARM: pxa: Wunused-result warning in viper board file
ARM: shark: fix shark_pci_init return code
Fixed trivial conflicts in arch/arm/mach-at91/setup.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since the complete conversion to device tree, there are no board-
specific Kconfig options left, so remove the useless Kconfig entry.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The PL310_ERRATA_753970 and ARM_ERRATA_764369 symbols only make sense
when the base features for them are enabled, so select them
conditionally in Kconfig to avoid warnings like:
warning: (UX500_SOC_COMMON) selects PL310_ERRATA_753970 which has unmet direct dependencies (CACHE_PL310)
warning: (ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC && UX500_SOC_COMMON) selects ARM_ERRATA_764369 which has unmet direct dependencies (CPU_V7 && SMP)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
|
|
Remove the legacy APB dma driver. The APB DMA support
is moved to dmaengine based Tegra APB DMA driver.
All clients are also moved to dmaengine based APB DMA
driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren:
ARM: tegra: remove board files
This branch removes all remaining board files for Tegra; booting is
now through device tree only.
Related, the Harmony DT is augmented with regulators, since this allows
removal of board-harmony-power.c; no other boards had regulator support.
This change depends on an enhancement to the TPS6586x regulator driver,
hence the dependency mentioned below.
* tag 'tegra-for-3.7-board-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra: harmony: configure power off
ARM: dt: tegra: harmony: add regulators
ARM: tegra: remove board (but not DT) support for Harmony
ARM: tegra: remove board (but not DT) support for Paz00
ARM: tegra: remove board (but not DT) support for TrimSlice
|
|
Harmony can be booted using device tree with equal functionality as when
booted using a board file. Remove as much of the board file as is
possible, since it's no longer needed.
Two special-cases are still left in board-dt-tegra20.c, since the Tegra
PCIe driver doesn't support device tree yet, and the Harmony .dts file
doesn't yet describe regulators which are needed for PCIe. This logic is
now enabled unconditionally rather than via CONFIG_MACH_HARMONY. While
this is more code than other boards, it's still unlikely to be much of a
problem, and both regulators and PCIe should be supported via device tree
in the near future, allowing the remaining code to be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Paz00 (Toshiba AC100) can be booted using device tree with equal
functionality as when booted using a board file. Remove as much of the
board file as is possible, since it's no longer needed.
One special-case is still left in board-dt-tegra20.c, since there is no
way to create a WiFi rfkill device from device tree yet. This logic is
now enabled unconditionally rather than via CONFIG_MACH_PAZ00. The extra
cases where it's enabled (.configs which did not enable Paz00 support)
shouldn't impact much since the amount of code is tiny.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Marc Dietrich <marvin24@gmx.de>
|
|
TrimSlice can be booted using device tree with equal functionality as
when booted using a board file. Remove the board file since it's no
longer needed.
One special-case is still left in board-dt-tegra20.c, since the Tegra
PCIe driver doesn't support device tree yet. This logic is now enabled
by CONFIG_TEGRA_PCI rather than via CONFIG_MACH_TRIMSLICE. The extra
cases where it's enabled (.configs which did not enable TrimSlice
support) shouldn't impact much since the amount of code is tiny.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
ARCH_TEGRA (arch/arm/Kconfig) now selects USE_OF, so there's not need
for ARCH_TEGRA_3x_SOC to do so too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The Seaboard device tree supports all the features that the Seaboard
board files support. Hence, there's no need to keep the board files
around any more; all users should convert to device tree.
MACH_KAEN and MACH_WARIO are also removed. While tegra-seaboard.dts
doesn't support those explicitly, it would be trivial to create device
trees for those boards if anyone cares.
The Seaboard device tree is now compiled if Tegra2 support is enabled,
rather than when Seaboard support is enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
* Make ARCH_TEGRA select USE_OF; DT is the way forward.
* Build board-dt-tegra*.c when the relevant Tegra SoC support is enabled,
rather than requiring a specific config option for this.
* The board-specific config options already build board-*-pinmux.o, and
when booting from device tree these files are no longer needed, so we
can remove some Makefile commands related to those files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Update Makefile.boot to compile *.dts when the appropriate Tegra SoC
support is enabled, rather than requiring Kconfig to list each board
individually. Remove CONFIG_MACH_VENTANA now that it has no use.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The Tegra ASoC machine drivers only depend on Tegra architecture support
to compile, not specific board support. Remove Kconfig dependencies on
any particular board. This is required since Kconfig options for boards
are going away given the migration to device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/drivers
* tegra/ahb:
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Tegra AHB Bus conforms to the AMBA Specification (Rev 2.0) Advanced
High-performance Bus (AHB) architecture.
The AHB Arbiter controls AHB bus master arbitration. This effectively
forms a second level of arbitration for access to the memory
controller through the AHB Slave Memory device. The AHB pre-fetch
logic can be configured to enhance performance for devices doing
sequential access. Each AHB master is assigned to either the high or
low priority bin. Both Tegra20/30 have this AHB bus.
Some of configuration params could be passed from DT too if needed.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Tegra has 5 UARTS which could be used for low-level debug output. Commit
fe26398 "ARM: tegra: uncompress.h: Choose a UART at runtime" implemented
one method for the kernel to automatically determine which of these to
use at run-time, so that the same DEBUG_LL-enabled kernel image could be
used across multiple Tegra boards. The required bootloader-side setup for
that option is implemented in NVIDIA's various downstream U-Boot branches,
but the U-Boot maintainers have refused to accept it upstream.
This change implements an alternative automatic UART selection option
using ODMDATA. This is a 32-bit value programmed into Tegra's boot memory
which provides a few pieces of basic board-specific information, including
a field that indicates the console UART. Setting up this value is part of
the standard Tegra boot architecture, and so requires no Tegra-specific
hacks in the bootloader's UART driver.
Note that in theory, the format of ODMDATA is board-specific. However, in
practice all boards use the same location/size/values for the UART field.
ODMDATA[19:18] (which drive the type of debug console) is more problematic,
since some boards use value 2 for UART and others use 3. This patch just
accepts either value; if this doesn't work well for a given board, I'd
suggest simply not enabling this debug option when building for that board.
Note that the kernel assumes the bootloader has already set up any required
pinmux settings for the UART; there is no way the kernel can do this for
itself prior to knowing which board it's running on. In practice, people
using this feature are highly likely to be using bootloaders that have
indeed configured the pinmux. This assumption existed prior to this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Pull "ARM: timer cleanup work" from Arnd Bergmann:
"These are split out from the generic soc and driver updates because
there was a lot of conflicting work by multiple people. Marc Zyngier
worked on simplifying the "localtimer" interfaces, and some of the
platforms are touching the same code as they move to device tree based
booting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
ARM: tegra: select USB_ULPI if USB is selected
arm/tegra: pcie: fix return value of function
ARM: ux500: fix compilation after local timer rework
ARM: shmobile: remove additional __io() macro use
ARM: local timers: make the runtime registration interface mandatory
ARM: local timers: convert MSM to runtime registration interface
ARM: local timers: convert exynos to runtime registration interface
ARM: smp_twd: remove old local timer interface
ARM: imx6q: convert to twd_local_timer_register() interface
ARM: highbank: convert to twd_local_timer_register() interface
ARM: ux500: convert to twd_local_timer_register() interface
ARM: shmobile: convert to twd_local_timer_register() interface
ARM: tegra: convert to twd_local_timer_register() interface
ARM: plat-versatile: convert to twd_local_timer_register() interface
ARM: OMAP4: convert to twd_local_timer_register() interface
ARM: smp_twd: add device tree support
ARM: smp_twd: add runtime registration support
ARM: local timers: introduce a new registration interface
ARM: smp_twd: make local_timer_stop a symbol instead of a #define
ARM: mach-shmobile: default to no earlytimer
...
|
|
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
|
|
Automatically select USB_ULPI if USB is enabled on Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This causes the Tegra pinctrl driver to be built whenever core Tegra
support is enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The tegra cpufreq implementation relies on the cpu_freq_table
code, so make sure that this is always there when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The ARM IP revisions in Tegra are:
Tegra20: CPU r1p1, PL310 r2p0
Tegra30: CPU A01=r2p7/>=A02=r2p9, NEON r2p3-50, PL310 r3p1-50
Based on work by Olof Johansson, although the actual list of errata is
somewhat different here, since I added a bunch more and removed one PL310
erratum that doesn't seem applicable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Now that Tegra20 and Tegra30 device tree board files are separate,
MACH_TEGRA_DT (which enables the Tegra20 device tree board file) should
depend on Tegra20 support being enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add support for tegra30 SoC. This includes a device tree compatible type for
this SoC ("nvidia,tegra30") and adds L2 cache initialization for this new SoC.
The clock framework is still missing, which prevents most drivers from working.
The basic IRQs are the same, so remove the dependency on
CONFIG_ARCH_TEGRA_2x_SOC.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Tegra20 based boards will be handled by the current board-dt.c file. Tegra30
based boards will be handled by a new board-dt-tegra30.c file. Hence rename
the existing board-dt.c to board-dt-tegra20.c to reflect its use.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* add a dependency to ARCH_TEGRA_2x_SOC in Kconfig to all tegra20 based boards
and TEGRA_PCI
* make powergating dependent on ARCH_TEGRA_2x_SOC
* remove dependency on ARCH_TEGRA_2x_SOC for clock.c
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (21 commits)
arm/dt: tegra devicetree support
arm/versatile: Add device tree support
dt/irq: add irq_domain_generate_simple() helper
irq: add irq_domain translation infrastructure
dmaengine: imx-sdma: add device tree probe support
dmaengine: imx-sdma: sdma_get_firmware does not need to copy fw_name
dmaengine: imx-sdma: use platform_device_id to identify sdma version
mmc: sdhci-esdhc-imx: add device tree probe support
mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
mmc: sdhci-esdhc-imx: do not reference platform data after probe
mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
net/fec: add device tree probe support
net: ibm_newemac: convert it to use of_get_phy_mode
dt/net: add helper function of_get_phy_mode
net/fec: gasket needs to be enabled for some i.mx
serial/imx: add device tree probe support
serial/imx: get rid of the uses of cpu_is_mx1()
arm/dt: Add dtb make rule
arm/dt: Add skeleton dtsi file
...
|
|
Everything required to populate NVIDIA Tegra devices from the device
tree. This patch adds a new DT_MACHINE_DESC() which matches against
a tegra20 device tree. So far it only registers the on-chip devices,
but it will be refined in follow on patches to configure clocks and
pin IO from the device tree also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This fixes:
warning: (MACH_HARMONY && MACH_KAEN && MACH_SEABOARD) selects MACH_HAS_SND_SOC_TEGRA_WM8903 which has unmet direct dependencies (SOUND && !M68K && SND && SND_SOC)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Colin Cross <ccross@android.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
CONFIG_SND_SOC_TEGRA_WM8903 is useful for many Tegra boards. To avoid the
ASoC tegra/Kconfig enumerating them all, instead have the Tegra machine
Kconfig select MACH_HAS_SND_SOC_TEGRA_WM8903 where appropriate, and have
SND_SOC_TEGRA_WM8903 depend on this.
[Redid ASoC diff so it applies. -- broonie]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
ARM: tegra: harmony: initialize the TPS65862 PMIC
ARM: tegra: update defconfig
ARM: tegra: harmony: update PCI-e initialization sequence
ARM: tegra: trimslice: enable MMC/SD slots
ARM: tegra: enable new drivers in defconfig
ARM: tegra: Add Toshiba AC100 support
ARM: tegra: harmony: Set WM8903 gpio_base
ARM: tegra: harmony: I2C-related portions of audio support
ARM: tegra: harmony: register i2c devices
ARM: tegra: seaboard: register i2c devices
ARM: tegra: harmony: Beginnings of audio support
ARM: tegra: create defines for SD-related GPIO names
ARM: tegra: add devices.c entries for audio
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (172 commits)
USB: Add support for SuperSpeed isoc endpoints
xhci: Clean up cycle bit math used during stalls.
xhci: Fix cycle bit calculation during stall handling.
xhci: Update internal dequeue pointers after stalls.
USB: Disable auto-suspend for USB 3.0 hubs.
USB: Remove bogus USB_PORT_STAT_SUPER_SPEED symbol.
xhci: Return canceled URBs immediately when host is halted.
xhci: Fixes for suspend/resume of shared HCDs.
xhci: Fix re-init on power loss after resume.
xhci: Make roothub functions deal with device removal.
xhci: Limit roothub ports to 15 USB3 & 31 USB2 ports.
xhci: Return a USB 3.0 hub descriptor for USB3 roothub.
xhci: Register second xHCI roothub.
xhci: Change xhci_find_slot_id_by_port() API.
xhci: Refactor bus suspend state into a struct.
xhci: Index with a port array instead of PORTSC addresses.
USB: Set usb_hcd->state and flags for shared roothubs.
usb: Make core allocate resources per PCI-device.
usb: Store bus type in usb_hcd, not in driver flags.
usb: Change usb_hcd->bandwidth_mutex to a pointer.
...
|
|
Interface used by Tegra's gadget driver and ehci driver
to power on and configure the USB PHYs.
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds the config infrastructure, the pinmux and basic
board setup code for PAZ00 (name of board inside the AC100/AZ).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This adds board support for the Seaboard eval platform and some of the
derivatives that are very similar. Since they only differ in some very
minor ways, most of the code is shared.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
|
|
The option isn't terribly useful on other ARM platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
|
|
The frequency memory bus on Tegra can be adjusted without
disabling accesses to memory by updating the memory
configuration registers from a per-board table, and then
changing the clock frequency. The clock controller and
memory controller have an interlock that prevents the
new memory registers from taking effect until the
clock frequency change.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
|
