aboutsummaryrefslogtreecommitdiff
path: root/drivers/ata
AgeCommit message (Collapse)Author
2014-06-18libata: Blacklist queued trim for Crucial M500Martin K. Petersen
commit 3b8d2676d15d6b2326757adb66b70a9cd6650373 upstream. Queued trim only works for some users with MU05 firmware. Revert to blacklisting all firmware versions. Introduced by commit d121f7d0cbb8 ("libata: Update queued trim blacklist for M5x0 drives") which this effectively reverts, while retaining the blacklisting of M550. See https://bugzilla.kernel.org/show_bug.cgi?id=71371 for reports of trouble with MU05 firmware. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-18libata: clean up ZPODD when a port is detachedLevente Kurusa
commit a6f9bf4d2f965b862b95213303d154e02957eed8 upstream. When a ZPODD device is unbound via sysfs, the ACPI notify handler is not removed. This causes panics as observed in Bug #74601. The panic only happens when the wake happens from outside the kernel (i.e. inserting a media or pressing a button). Add a loop to ata_port_detach which loops through the port's devices and checks if zpodd is enabled, if so call zpodd_exit. Reviewed-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Levente Kurusa <levex@linux.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-18pata_at91: fix ata_host_activate() failure handlingBartlomiej Zolnierkiewicz
commit 27aa64b9d1bd0d23fd692c91763a48309b694311 upstream. Add missing clk_put() call to ata_host_activate() failure path. Sergei says, "Hm, I have once fixed that (see that *if* (!ret)) but looks like a later commit 477c87e90853d136b188c50c0e4a93d01cad872e (ARM: at91/pata: use gpio_is_valid to check the gpio) broke it again. :-( Would be good if the changelog did mention that..." Cc: Andrew Victor <linux@maxim.org.za> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-18libata: Update queued trim blacklist for M5x0 drivesMartin K. Petersen
commit d121f7d0cbb875abce249dbf7eb191f9bafe80b7 upstream. Crucial/Micron M500 drives properly support queued DSM TRIM starting with firmware MU05. Update the blacklist so we only disable queued trim for older firmware releases. Early M550 series drives suffer from the same issue as M500. A bugfix firmware is in the pipeline but not ready yet. Until then, blacklist queued trim for M550. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Chris Samuel <chris@csamuel.org> Cc: Marc MERLIN <marc@merlins.org> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-18ahci: Do not receive interrupts sent by dummy portsAlexander Gordeev
commit 2cf532f5e67c0cfe38c8c100e49280cdadacd2be upstream. In multiple MSI mode all AHCI ports (including dummy) get assigned separate MSI vectors and (as result of execution pci_enable_msi_exact() function) separate IRQ numbers, (mapped to the MSI vectors). Therefore, although interrupts from dummy ports are not desired they are still enabled. We do not request IRQs for dummy ports, but that only means we do not assign AHCI-specific ISRs to corresponding IRQ numbers. As result, dummy port interrupts still could come and traverse all the way from the PCI device to the kernel, causing unnecessary overhead. This update disables IRQs for dummy ports and prevents the described issue. Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Tested-by: David Milburn <dmilburn@redhat.com> Cc: linux-ide@vger.kernel.org Fixes: 5ca72c4f7c41 ("AHCI: Support multiple MSIs") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-18ahci: Ensure "MSI Revert to Single Message" mode is not enforcedAlexander Gordeev
commit ab0f9e78b97f5193dd38b3757b42b6fbded05fb7 upstream. The AHCI specification allows hardware to choose to revert to single MSI mode when fewer messages are allocated than requested. Yet, at least ICH10 chipset reverts to single MSI mode even when enough messages are allocated in some cases (see below). This update forces the driver to not rely on initialization of multiple MSIs mode alone and always check if "MSI Revert to Single Message" (MRSM) mode was enforced by the controller and fallback to the single MSI mode in case it did. That prevents a situation when the driver configured multiple per-port IRQ handlers, but the controller sends all port's interrupts to a single IRQ, which could easily screw up the interrupt handling and lead to delays and possibly crashes. The fix was tested on a 6-port controller that successfully reverted to the single MSI mode: 00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller (prog-if 01 [AHCI 1.0]) Subsystem: Super Micro Computer Inc Device 10a7 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 101 I/O ports at f110 [size=8] I/O ports at f100 [size=4] I/O ports at f0f0 [size=8] I/O ports at f0e0 [size=4] I/O ports at f020 [size=32] Memory at fbf00000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit- Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA v1.0 Capabilities: [b0] PCI Advanced Features Kernel driver in use: ahci With 6 ports just 8 MSI vectors should be enough, but the adapter enforces the MRSM mode when less than 16 vectors are written to the Multiple Messages Enable PCI register. I instigated MRSM mode by forcing @nvec to 8 in ahci_init_interrupts(). Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: linux-ide@vger.kernel.org Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-18libata/ahci: accommodate tag ordered controllersDan Williams
commit 8a4aeec8d2d6a3edeffbdfae451cdf05cbf0fefd upstream. The AHCI spec allows implementations to issue commands in tag order rather than FIFO order: 5.3.2.12 P:SelectCmd HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1) or HBA selects the command to issue that has had the PxCI bit set to '1' longer than any other command pending to be issued. The result is that commands posted sequentially (time-wise) may play out of sequence when issued by hardware. This behavior has likely been hidden by drives that arrange for commands to complete in issue order. However, it appears recent drives (two from different vendors that we have found so far) inflict out-of-order completions as a matter of course. So, we need to take care to maintain ordered submission, otherwise we risk triggering a drive to fall out of sequential-io automation and back to random-io processing, which incurs large latency and degrades throughput. This issue was found in simple benchmarks where QD=2 seq-write performance was 30-50% *greater* than QD=32 seq-write performance. Tagging for -stable and making the change globally since it has a low risk-to-reward ratio. Also, word is that recent versions of an unnamed OS also does it this way now. So, drives in the field are already experienced with this tag ordering scheme. Cc: Dave Jiang <dave.jiang@intel.com> Cc: Ed Ciechanowski <ed.ciechanowski@intel.com> Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-18ahci: do not request irq for dummy portDavid Milburn
commit 9ae794ac5e407d3bc3fec785db481d5a2c0fa275 upstream. System may crash in ahci_hw_interrupt() or ahci_thread_fn() when accessing the interrupt status in a port's private_data if the port is actually a DUMMY port. 00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller <snip console output for linux-3.15-rc1> [ 9.352080] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x1 impl SATA mode [ 9.352084] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc [ 9.368155] Console: switching to colour frame buffer device 128x48 [ 9.439759] mgag200 0000:11:00.0: fb0: mgadrmfb frame buffer device [ 9.446765] mgag200 0000:11:00.0: registered panic notifier [ 9.470166] scsi1 : ahci [ 9.479166] scsi2 : ahci [ 9.488172] scsi3 : ahci [ 9.497174] scsi4 : ahci [ 9.506175] scsi5 : ahci [ 9.515174] scsi6 : ahci [ 9.518181] ata1: SATA max UDMA/133 abar m2048@0x95c00000 port 0x95c00100 irq 91 [ 9.526448] ata2: DUMMY [ 9.529182] ata3: DUMMY [ 9.531916] ata4: DUMMY [ 9.534650] ata5: DUMMY [ 9.537382] ata6: DUMMY [ 9.576196] [drm] Initialized mgag200 1.0.0 20110418 for 0000:11:00.0 on minor 0 [ 9.845257] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9.865161] ata1.00: ATAPI: Optiarc DVD RW AD-7580S, FX04, max UDMA/100 [ 9.891407] ata1.00: configured for UDMA/100 [ 9.900525] scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7580S FX04 PQ: 0 ANSI: 5 [ 10.247399] iTCO_vendor_support: vendor-support=0 [ 10.261572] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11 [ 10.269764] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS [ 10.301932] sd 0:2:0:0: [sda] 570310656 512-byte logical blocks: (291 GB/271 GiB) [ 10.317085] sd 0:2:0:0: [sda] Write Protect is off [ 10.328326] sd 0:2:0:0: [sda] Write cache: disabled, read cache: disabled, supports DPO and FUA [ 10.375452] BUG: unable to handle kernel NULL pointer dereference at 000000000000003c [ 10.384217] IP: [<ffffffffa0133df0>] ahci_hw_interrupt+0x100/0x130 [libahci] [ 10.392101] PGD 0 [ 10.394353] Oops: 0000 [#1] SMP [ 10.397978] Modules linked in: sr_mod(+) cdrom sd_mod iTCO_wdt crc_t10dif iTCO_vendor_support crct10dif_common ahci libahci libata lpc_ich mfd_core mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ttm drm i2c_core megaraid_sas dm_mirror dm_region_hash dm_log dm_mod [ 10.426499] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.15.0-rc1 #1 [ 10.433495] Hardware name: QCI QSSC-S4R/QSSC-S4R, BIOS QSSC-S4R.QCI.01.00.S013.032920111005 03/29/2011 [ 10.443886] task: ffffffff81906460 ti: ffffffff818f0000 task.ti: ffffffff818f0000 [ 10.452239] RIP: 0010:[<ffffffffa0133df0>] [<ffffffffa0133df0>] ahci_hw_interrupt+0x100/0x130 [libahci] [ 10.462838] RSP: 0018:ffff880033c03d98 EFLAGS: 00010046 [ 10.468767] RAX: 0000000000a400a4 RBX: ffff880029a6bc18 RCX: 00000000fffffffa [ 10.476731] RDX: 00000000000000a4 RSI: ffff880029bb0000 RDI: ffff880029a6bc18 [ 10.484696] RBP: ffff880033c03dc8 R08: 0000000000000000 R09: ffff88002f800490 [ 10.492661] R10: 0000000000000000 R11: 0000000000000005 R12: 0000000000000000 [ 10.500625] R13: ffff880029a6bd98 R14: 0000000000000000 R15: ffffc90000194000 [ 10.508590] FS: 0000000000000000(0000) GS:ffff880033c00000(0000) knlGS:0000000000000000 [ 10.517623] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 10.524035] CR2: 000000000000003c CR3: 00000000328ff000 CR4: 00000000000007b0 [ 10.531999] Stack: [ 10.534241] 0000000000000017 ffff880031ba7d00 000000000000005c ffff880031ba7d00 [ 10.542535] 0000000000000000 000000000000005c ffff880033c03e10 ffffffff810c2a1e [ 10.550827] ffff880031ae2900 000000008108fb4f ffff880031ae2900 ffff880031ae2984 [ 10.559121] Call Trace: [ 10.561849] <IRQ> [ 10.563994] [<ffffffff810c2a1e>] handle_irq_event_percpu+0x3e/0x1a0 [ 10.571309] [<ffffffff810c2bbd>] handle_irq_event+0x3d/0x60 [ 10.577631] [<ffffffff810c4fdd>] try_one_irq.isra.6+0x8d/0xf0 [ 10.584142] [<ffffffff810c5313>] note_interrupt+0x173/0x1f0 [ 10.590460] [<ffffffff810c2a8e>] handle_irq_event_percpu+0xae/0x1a0 [ 10.597554] [<ffffffff810c2bbd>] handle_irq_event+0x3d/0x60 [ 10.603872] [<ffffffff810c5727>] handle_edge_irq+0x77/0x130 [ 10.610199] [<ffffffff81014b8f>] handle_irq+0xbf/0x150 [ 10.616040] [<ffffffff8109ff4e>] ? vtime_account_idle+0xe/0x50 [ 10.622654] [<ffffffff815fca1a>] ? atomic_notifier_call_chain+0x1a/0x20 [ 10.630140] [<ffffffff816038cf>] do_IRQ+0x4f/0xf0 [ 10.635490] [<ffffffff815f8aed>] common_interrupt+0x6d/0x6d [ 10.641805] <EOI> [ 10.643950] [<ffffffff8149ca9f>] ? cpuidle_enter_state+0x4f/0xc0 [ 10.650972] [<ffffffff8149ca98>] ? cpuidle_enter_state+0x48/0xc0 [ 10.657775] [<ffffffff8149cb47>] cpuidle_enter+0x17/0x20 [ 10.663807] [<ffffffff810b0070>] cpu_startup_entry+0x2c0/0x3d0 [ 10.670423] [<ffffffff815dfcc7>] rest_init+0x77/0x80 [ 10.676065] [<ffffffff81a60f47>] start_kernel+0x40f/0x41a [ 10.682190] [<ffffffff81a60941>] ? repair_env_string+0x5c/0x5c [ 10.688799] [<ffffffff81a60120>] ? early_idt_handlers+0x120/0x120 [ 10.695699] [<ffffffff81a605ee>] x86_64_start_reservations+0x2a/0x2c [ 10.702889] [<ffffffff81a60733>] x86_64_start_kernel+0x143/0x152 [ 10.709689] Code: a0 fc ff 85 c0 8b 4d d4 74 c3 48 8b 7b 08 89 ca 48 c7 c6 60 66 13 a0 31 c0 e8 9d 70 28 e1 8b 4d d4 eb aa 0f 1f 84 00 00 00 00 00 <45> 8b 64 24 3c 48 89 df e8 23 47 4c e1 41 83 fc 01 19 c0 48 83 [ 10.731470] RIP [<ffffffffa0133df0>] ahci_hw_interrupt+0x100/0x130 [libahci] [ 10.739441] RSP <ffff880033c03d98> [ 10.743333] CR2: 000000000000003c [ 10.747032] ---[ end trace b6e82636970e2690 ]--- [ 10.760190] Kernel panic - not syncing: Fatal exception in interrupt [ 10.767291] Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff) Cc: Alexander Gordeev <agordeev@redhat.com> Cc: Tejun Heo <tj@kernel.org> Signed-of-by: David Milburn <dmilburn@redhat.com> Fixes: 5ca72c4f7c41 ("AHCI: Support multiple MSIs")
2014-04-16ata: ahci: support hisilicon deviceHaojian Zhuang
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
2014-04-16ata: ahci: append new hflagHaojian Zhuang
Append AHCI_HFLAG_NO_FBS to force turning off FBS flag. Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
2014-04-16ahci: add support for Hisilicon sataKefeng Wang
The hip04 SoC of hisilicon has an AHCI compliant SATA controller. This patch adds the compatible string, and the controller is compliant with the ahci 1.3 and sata 3.0 specification. ISSUE: The hardware has defective designs. Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
2014-04-16ata: samsung: Rebase as per 3.10-rc1Yuvaraj Kumar C D
This patchset integrate the SATA patches submitted by Vasanth Ananthan. In addition to that SATA and SATA PHY driver will use common clock framework API. Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
2014-04-16ata: exynos: Remove __init attribute to fix kernel crashTushar Behera
The probe function of SATA phy driver is being accessed later in SATA probe. But it gets poisoned memory during that time. Suspecting __init attribute to be the culprit. Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
2014-04-16ata: samsung: Add SATA PHY controller driverVasanth Ananthan
This patch adds a platform driver and I2C client driver for SATA PHY controller Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
2014-04-16ata: samsung: Add SATA controller driverVasanth Ananthan
This patch adds a platform driver for SATA controller. Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
2014-04-16ata: Add SATA PHY utility frameworkVasanth Ananthan
This patch adds SATA PHY utility framework APIs. The framework acts as an interface between the SATA device and the PHY device. The SATA PHY device registers itself with the framework through the APIs provided and the SATA device finds and requests for an appropriate PHY device. Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
2014-03-10Merge branch 'for-3.14-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata fixlet from Tejun Heo: "I merged the two blaclist entries into 'Crucial_CT???M500SSD*'" * 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: libata: use wider match for blacklisting Crucial M500
2014-03-10libata: use wider match for blacklisting Crucial M500Tejun Heo
We're now blacklisting "Crucial_CT???M500SSD1" and "Crucial_CT???M500SSD3". Also, "Micron_M500*" is blacklisted which is about the same devices as the crucial branded ones. Let's merge the two Crucial M500 entries and widen the match to "Crucial_CT???M500SSD*" so that we don't have to fiddle with new entries for similar devices. Signed-off-by: Tejun Heo <tj@kernel.org> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@vger.kernel.org
2014-03-08Merge branch 'for-3.14-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata fixes from Tejun Heo: "Just a couple patches blacklisting more broken devices" * 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8 (2BA30001) libata: disable queued TRIM for Crucial M500 mSATA SSDs
2014-03-07libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint ↵Michele Baldessari
M8 (2BA30001) Via commit 87809942d3fa "libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8" we added a quirk for disks named "ST1000LM024 HN-M101MBB" with firmware revision "2AR10001". As reported on https://bugzilla.redhat.com/show_bug.cgi?id=1073901, we need to also add firmware revision 2BA30001 as it is broken as well. Reported-by: Nicholas <arealityfarbetween@googlemail.com> Signed-off-by: Michele Baldessari <michele@acksyn.org> Tested-by: Guilherme Amadio <guilherme.amadio@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
2014-03-03libata: disable queued TRIM for Crucial M500 mSATA SSDsMarios Andreopoulos
Queued TRIM commands cause problems and silent file system corruption on Crucial M500 SSDs. This patch disables them for the mSATA model of the drive. Signed-off-by: Marios Andreopoulos <opensource@andmarios.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org # 3.12+ Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71371
2014-02-20Merge tag 'pci-v3.14-fixes-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "The most interesting thing here is the change to enable INTx (by clearing PCI_COMMAND_INTX_DISABLE) if the BIOS left INTx disabled. Apparently the Baytrail BIOS does this, which means EHCI doesn't work. Also, fix an AHCI MSI regression and other issues with the recent MSI changes. This also adds pci_enable_msi_exact() and pci_enable_msix_exact(), which aren't regression fixes, but will keep us from touching drivers twice (once to stop using the deprecated pci_enable_msi(), etc., and again to use the *_exact() variants). There's also a minor MVEBU fix. Summary: MSI: - Fix AHCI single-MSI fallback (Alexander Gordeev) - Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman) - Fix htmldocs problem (Masanari Iida) - Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev) - Update documentation (Alexander Gordeev) Miscellaneous: - mvebu: expose device ID & revision via lspci (Andrew Lunn) - Enable INTx if the BIOS left them disabled (Bjorn Helgaas)" * tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: ahci: Fix broken fallback to single MSI mode PCI: Enable INTx if BIOS left them disabled PCI/MSI: Add pci_enable_msi_exact() and pci_enable_msix_exact() PCI/MSI: Fix cut-and-paste errors in documentation PCI/MSI: Add pci_enable_msi() documentation back PCI/MSI: Fix pci_msix_vec_count() htmldocs failure PCI/MSI: Fix leak of msi_attrs PCI/MSI: Check kmalloc() return value, fix leak of name PCI: mvebu: Use Device ID and revision from underlying endpoint
2014-02-20Merge branch 'for-3.14-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata fixes from Tejun Heo: "Various device specific fixes. Nothing too interesting" * 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: ahci: disable NCQ on Samsung pci-e SSDs on macbooks ata: sata_mv: Cleanup only the initialized ports sata_sil: apply MOD15WRITE quirk to TOSHIBA MK2561GSYN ata: enable quirk from jmicron JMB350 for JMB394 ATA: SATA_MV: Add missing Kconfig select statememnt ata: pata_imx: Check the return value from clk_prepare_enable()
2014-02-18ahci: disable NCQ on Samsung pci-e SSDs on macbooksLevente Kurusa
Samsung's pci-e SSDs with device ID 0x1600 which are found on some macbooks time out on NCQ commands. Blacklist NCQ on the device so that the affected machines can at least boot. Original-patch-by: Levente Kurusa <levex@linux.com> Signed-off-by: Tejun Heo <tj@kernel.org> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731 Cc: stable@vger.kernel.org
2014-02-16ata: sata_mv: Cleanup only the initialized portsEzequiel Garcia
When an error occurs in the port initialization loop, currently the driver tries to cleanup all the ports. This results in a NULL pointer dereference if the ports were only partially initialized. Fix this by updating only the number of initialized ports (either with failure or successfully), before jumping to the error path and looping over that number in the cleanup loop. Cc: Andrew Lunn <andrew@lunn.ch> Reported-by: Mikael Pettersson <mikpelinux@gmail.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
2014-02-14ahci: Fix broken fallback to single MSI modeAlexander Gordeev
Commit 7b92b4f61ec4 ("PCI/MSI: Remove pci_enable_msi_block_auto()") introduced a regression: if multiple MSI initialization fails, the code falls back to INTx rather than to single MSI. Fixes: 7b92b4f61ec4 ("PCI/MSI: Remove pci_enable_msi_block_auto()") Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Tejun Heo <tj@kernel.org>
2014-02-05ata: sata_mv: Fix probe failures with optional physAndrew Lunn
Make use of devm_phy_optional_get() in order to fix probe failures on Armada 370, XP and others, when there is no phy driver available. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: Tejun Heo <tj@kernel.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2014-02-03sata_sil: apply MOD15WRITE quirk to TOSHIBA MK2561GSYNTejun Heo
It's a bit odd to see a newer device showing mod15write; however, the reported behavior is highly consistent and other factors which could contribute seem to have been verified well enough. Also, both sata_sil itself and the drive are fairly outdated at this point making the risk of this change fairly low. It is possible, probably likely, that other drive models in the same family have the same problem; however, for now, let's just add the specific model which was tested. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: matson <lists-matsonpa@luxsci.me> References: http://lkml.kernel.org/g/201401211912.s0LJCk7F015058@rs103.luxsci.com Cc: stable@vger.kernel.org
2014-01-31ata: enable quirk from jmicron JMB350 for JMB394Denis V. Lunev
Without the patch the kernel generates the following error. ata11.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata11.15: Port Multiplier vendor mismatch '0x197b' != '0x123' ata11.15: PMP revalidation failed (errno=-19) ata11.15: failed to recover PMP after 5 tries, giving up This patch helps to bypass this error and the device becomes functional. Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: <linux-ide@vger.kernel.org> Cc: stable@vger.kernel.org
2014-01-29ATA: SATA_MV: Add missing Kconfig select statememntAndrew Lunn
SATA_MV depends on GENERIC_PHY. So if SATA_MV is built in, GENERIC_PHY cannot be modular. Fixes build error found by kbuild test robot. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-29ata: pata_imx: Check the return value from clk_prepare_enable()Fabio Estevam
clk_prepare_enable() may fail, so let's check its return value and propagate it in the case of error. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-24Merge tag 'pm+acpi-3.14-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI and power management updates from Rafael Wysocki: "As far as the number of commits goes, the top spot belongs to ACPI this time with cpufreq in the second position and a handful of PM core, PNP and cpuidle updates. They are fixes and cleanups mostly, as usual, with a couple of new features in the mix. The most visible change is probably that we will create struct acpi_device objects (visible in sysfs) for all devices represented in the ACPI tables regardless of their status and there will be a new sysfs attribute under those objects allowing user space to check that status via _STA. Consequently, ACPI device eject or generally hot-removal will not delete those objects, unless the table containing the corresponding namespace nodes is unloaded, which is extremely rare. Also ACPI container hotplug will be handled quite a bit differently and cpufreq will support CPU boost ("turbo") generically and not only in the acpi-cpufreq driver. Specifics: - ACPI core changes to make it create a struct acpi_device object for every device represented in the ACPI tables during all namespace scans regardless of the current status of that device. In accordance with this, ACPI hotplug operations will not delete those objects, unless the underlying ACPI tables go away. - On top of the above, new sysfs attribute for ACPI device objects allowing user space to check device status by triggering the execution of _STA for its ACPI object. From Srinivas Pandruvada. - ACPI core hotplug changes reducing code duplication, integrating the PCI root hotplug with the core and reworking container hotplug. - ACPI core simplifications making it use ACPI_COMPANION() in the code "glueing" ACPI device objects to "physical" devices. - ACPICA update to upstream version 20131218. This adds support for the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug facilities. From Bob Moore, Lv Zheng and Betty Dall. - Init code change to carry out the early ACPI initialization earlier. That should allow us to use ACPI during the timekeeping initialization and possibly to simplify the EFI initialization too. From Chun-Yi Lee. - Clenups of the inclusions of ACPI headers in many places all over from Lv Zheng and Rashika Kheria (work in progress). - New helper for ACPI _DSM execution and rework of the code in drivers that uses _DSM to execute it via the new helper. From Jiang Liu. - New Win8 OSI blacklist entries from Takashi Iwai. - Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria, Tang Chen, Zhang Rui. - intel_pstate driver updates, including proper Baytrail support, from Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra. - Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski. - powernow-k6 cpufreq driver fixes from Mikulas Patocka. - cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown. - Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar. - cpuidle cleanups from Bartlomiej Zolnierkiewicz. - Support for hibernation APM events from Bin Shi. - Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled during thaw transitions from Bjørn Mork. - PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson. - PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa, Rashika Kheria. - New tool for profiling system suspend from Todd E Brandt and a cpupower tool cleanup from One Thousand Gnomes" * tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits) thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412) cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ Documentation: cpufreq / boost: Update BOOST documentation cpufreq: exynos: Extend Exynos cpufreq driver to support boost cpufreq / boost: Kconfig: Support for software-managed BOOST acpi-cpufreq: Adjust the code to use the common boost attribute cpufreq: Add boost frequency support in core intel_pstate: Add trace point to report internal state. cpufreq: introduce cpufreq_generic_get() routine ARM: SA1100: Create dummy clk_get_rate() to avoid build failures cpufreq: stats: create sysfs entries when cpufreq_stats is a module cpufreq: stats: free table and remove sysfs entry in a single routine cpufreq: stats: remove hotplug notifiers cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly cpufreq: speedstep: remove unused speedstep_get_state platform: introduce OF style 'modalias' support for platform bus PM / tools: new tool for suspend/resume performance optimization ACPI: fix module autoloading for ACPI enumerated devices ACPI: add module autoloading support for ACPI enumerated devices ACPI: fix create_modalias() return value handling ...
2014-01-22Merge tag 'pci-v3.14-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "PCI changes for the v3.14 merge window: Resource management - Change pci_bus_region addresses to dma_addr_t (Bjorn Helgaas) - Support 64-bit AGP BARs (Bjorn Helgaas, Yinghai Lu) - Add pci_bus_address() to get bus address of a BAR (Bjorn Helgaas) - Use pci_resource_start() for CPU address of AGP BARs (Bjorn Helgaas) - Enforce bus address limits in resource allocation (Yinghai Lu) - Allocate 64-bit BARs above 4G when possible (Yinghai Lu) - Convert pcibios_resource_to_bus() to take pci_bus, not pci_dev (Yinghai Lu) PCI device hotplug - Major rescan/remove locking update (Rafael J. Wysocki) - Make ioapic builtin only (not modular) (Yinghai Lu) - Fix release/free issues (Yinghai Lu) - Clean up pciehp (Bjorn Helgaas) - Announce pciehp slot info during enumeration (Bjorn Helgaas) MSI - Add pci_msi_vec_count(), pci_msix_vec_count() (Alexander Gordeev) - Add pci_enable_msi_range(), pci_enable_msix_range() (Alexander Gordeev) - Deprecate "tri-state" interfaces: fail/success/fail+info (Alexander Gordeev) - Export MSI mode using attributes, not kobjects (Greg Kroah-Hartman) - Drop "irq" param from *_restore_msi_irqs() (DuanZhenzhong) SR-IOV - Clear NumVFs when disabling SR-IOV in sriov_init() (ethan.zhao) Virtualization - Add support for save/restore of extended capabilities (Alex Williamson) - Add Virtual Channel to save/restore support (Alex Williamson) - Never treat a VF as a multifunction device (Alex Williamson) - Add pci_try_reset_function(), et al (Alex Williamson) AER - Ignore non-PCIe error sources (Betty Dall) - Support ACPI HEST error sources for domains other than 0 (Betty Dall) - Consolidate HEST error source parsers (Bjorn Helgaas) - Add a TLP header print helper (Borislav Petkov) Freescale i.MX6 - Remove unnecessary code (Fabio Estevam) - Make reset-gpio optional (Marek Vasut) - Report "link up" only after link training completes (Marek Vasut) - Start link in Gen1 before negotiating for Gen2 mode (Marek Vasut) - Fix PCIe startup code (Richard Zhu) Marvell MVEBU - Remove duplicate of_clk_get_by_name() call (Andrew Lunn) - Drop writes to bridge Secondary Status register (Jason Gunthorpe) - Obey bridge PCI_COMMAND_MEM and PCI_COMMAND_IO bits (Jason Gunthorpe) - Support a bridge with no IO port window (Jason Gunthorpe) - Use max_t() instead of max(resource_size_t,) (Jingoo Han) - Remove redundant of_match_ptr (Sachin Kamat) - Call pci_ioremap_io() at startup instead of dynamically (Thomas Petazzoni) NVIDIA Tegra - Disable Gen2 for Tegra20 and Tegra30 (Eric Brower) Renesas R-Car - Add runtime PM support (Valentine Barshak) - Fix rcar_pci_probe() return value check (Wei Yongjun) Synopsys DesignWare - Fix crash in dw_msi_teardown_irq() (Bjørn Erik Nilsen) - Remove redundant call to pci_write_config_word() (Bjørn Erik Nilsen) - Fix missing MSI IRQs (Harro Haan) - Add dw_pcie prefix before cfg_read/write (Pratyush Anand) - Fix I/O transfers by using CPU (not realio) address (Pratyush Anand) - Whitespace cleanup (Jingoo Han) EISA - Call put_device() if device_register() fails (Levente Kurusa) - Revert EISA initialization breakage ((Bjorn Helgaas) Miscellaneous - Remove unused code, including PCIe 3.0 interfaces (Stephen Hemminger) - Prevent bus conflicts while checking for bridge apertures (Bjorn Helgaas) - Stop clearing bridge Secondary Status when setting up I/O aperture (Bjorn Helgaas) - Use dev_is_pci() to identify PCI devices (Yijing Wang) - Deprecate DEFINE_PCI_DEVICE_TABLE (Joe Perches) - Update documentation 00-INDEX (Erik Ekman)" * tag 'pci-v3.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (119 commits) Revert "EISA: Initialize device before its resources" Revert "EISA: Log device resources in dmesg" vfio-pci: Use pci "try" reset interface PCI: Check parent kobject in pci_destroy_dev() xen/pcifront: Use global PCI rescan-remove locking powerpc/eeh: Use global PCI rescan-remove locking PCI: Fix pci_check_and_unmask_intx() comment typos PCI: Add pci_try_reset_function(), pci_try_reset_slot(), pci_try_reset_bus() MPT / PCI: Use pci_stop_and_remove_bus_device_locked() platform / x86: Use global PCI rescan-remove locking PCI: hotplug: Use global PCI rescan-remove locking pcmcia: Use global PCI rescan-remove locking ACPI / hotplug / PCI: Use global PCI rescan-remove locking ACPI / PCI: Use global PCI rescan-remove locking in PCI root hotplug PCI: Add global pci_lock_rescan_remove() PCI: Cleanup pci.h whitespace PCI: Reorder so actual code comes before stubs PCI/AER: Support ACPI HEST AER error sources for PCI domains other than 0 ACPICA: Add helper macros to extract bus/segment numbers from HEST table. PCI: Make local functions static ...
2014-01-21Merge branch 'for-3.14' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata updates from Tejun Heo: "Support for some new embedded controllers. A couple late (<= a week) fixes have stable cc'd and one patch ("SATA: MV: Add support for the optional PHYs") got committed yesterday because otherwise the resulting kernel would fail boot on an embedded board due to interdependent changes in its platform tree. Other than that, nothing too noteworthy" * 'for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: SATA: MV: Add support for the optional PHYs sata-highbank: Remove unnecessary ahci_platform.h include libata: disable LPM for some WD SATA-I devices ARM: mvebu: update the SATA compatible string for Armada 370/XP ata: sata_mv: fix disk hotplug for Armada 370/XP SoCs ata: sata_mv: introduce compatible string "marvell, armada-370-sata" ata: pata_samsung_cf: Remove unused macros ata: pata_samsung_cf: Use devm_ioremap_resource() ata: pata_samsung_cf: Merge pata_samsung_cf.h into pata_samsung_cf.c ata: pata_samsung_cf: Move plat/regs-ata.h to drivers/ata drivers: ata: Mark the function as static in libahci.c drivers: ata: Mark the function ahci_init_interrupts() as static in ahci.c ahci: imx: fix the error handling in imx_ahci_probe() ahci: imx: ahci_imx_softreset() can be static ahci: imx: Add i.MX53 support ahci: imx: Pull out the clock enable/disable calls libata, dt: Document sata_rcar bindings sata_rcar: Add R-Car Gen2 SATA PHY support ahci: mcp89: enter AHCI mode under Apple BIOS emulation ata: libata-eh: Remove unnecessary snprintf arithmetic
2014-01-20SATA: MV: Add support for the optional PHYsAndrew Lunn
Some Marvell SoCs have a SATA PHY which can be powered off, in order to save power. Make use of the generic phy framework to control these phys. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-19sata-highbank: Remove unnecessary ahci_platform.h includeHans de Goede
The sata-highbank driver is a complete standalone sata driver, which does not use ahci_platform.c / ahci_platform_data in any way. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-16libata: disable LPM for some WD SATA-I devicesTejun Heo
For some reason, some early WD drives spin up and down drives erratically when the link is put into slumber mode which can reduce the life expectancy of the device significantly. Unfortunately, we don't have full list of devices and given the nature of the issue it'd be better to err on the side of false positives than the other way around. Let's disable LPM on all WD devices which match one of the known problematic model prefixes and are SATA-I. As horkage list doesn't support matching SATA capabilities, this is implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is set for the known prefixes and sets the latter if the matched device is SATA-I. Note that this isn't optimal as this disables all LPM operations and partial link power state reportedly works fine on these; however, the way LPM is implemented in libata makes it difficult to precisely map libata LPM setting to specific link power state. Well, these devices are already fairly outdated. Let's just disable whole LPM for now. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com> Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com> References: https://bugzilla.kernel.org/show_bug.cgi?id=57211 Cc: stable@vger.kernel.org
2014-01-16Merge branch 'for-3.13-fixes' into for-3.14Tejun Heo
A scheduled horkage patch will conflict with HORKAGE changes in for-3.13-fixes. Pull in to avoid unnecessary merge conflicts. Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-15ata: sata_mv: fix disk hotplug for Armada 370/XP SoCsLior Amsalem
On Armada 370/XP SoCs, once a disk is removed from a SATA port, then the re-plug events are not detected by the sata_mv driver. This patch fixes the issue by updating the PHY speed in the LP_PHY_CTL register (0x58) according to the SControl speed. Note that this fix is only applied if the compatible string "marvell,armada-370-sata" is found in the SATA DT node. Fixes: 9ae6f740b49f ("arm: mach-mvebu: add support for Armada 370 and Armada XP with DT") Signed-off-by: Lior Amsalem <alior@marvell.com> Signed-off-by: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@free-electrons.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: stable@vger.kernel.org # v3.6+ Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-15ata: sata_mv: introduce compatible string "marvell, armada-370-sata"Simon Guinot
The sata_mv driver supports the SATA IP found in several Marvell SoCs. As some new SATA registers have been introduced with the Armada 370/XP SoCs, a way to identify them is needed. This patch introduces a new compatible string for the SATA IP found in Armada 370/XP SoCs. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@free-electrons.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Lior Amsalem <alior@marvell.com> Cc: stable@vger.kernel.org # v3.6+ Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-12Merge branch 'acpi-hotplug'Rafael J. Wysocki
* acpi-hotplug: ACPI / scan: ACPI device object sysfs attribute for _STA evaluation ACPI / hotplug / driver core: Handle containers in a special way ACPI / hotplug: Add demand_offline hotplug profile flag ACPI / bind: Move acpi_get_child() to drivers/ide/ide-acpi.c ACPI / bind: Pass struct acpi_device pointer to acpi_bind_one() ACPI / bind: Rework struct acpi_bus_type ACPI / bind: Redefine acpi_preset_companion() ACPI / bind: Redefine acpi_get_child() PCI / ACPI: Use acpi_find_child_device() for child devices lookup ACPI / bind: Simplify child device lookups ACPI / scan: Use direct recurrence for device hierarchy walks ACPI: Introduce acpi_set_device_status() ACPI / hotplug: Drop unfinished global notification handling routines ACPI / hotplug: Rework generic code to handle suprise removals ACPI / hotplug: Move container-specific code out of the core ACPI / hotplug: Make ACPI PCI root hotplug use common hotplug code ACPI / hotplug: Introduce common hotplug function acpi_device_hotplug() ACPI / hotplug: Do not fail bus and device checks for disabled hotplug ACPI / scan: Add acpi_device objects for all device nodes in the namespace ACPI / scan: Define non-empty device removal handler
2014-01-12Merge branch 'acpi-cleanup'Rafael J. Wysocki
* acpi-cleanup: (22 commits) ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment. ACPI / tables: Check if id is NULL in acpi_table_parse() ACPI / proc: Include appropriate header file in proc.c ACPI / EC: Remove unused functions and add prototype declaration in internal.h ACPI / dock: Include appropriate header file in dock.c ACPI / PCI: Include appropriate header file in pci_link.c ACPI / PCI: Include appropriate header file in pci_slot.c ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c ACPI / NVS: Include appropriate header file in nvs.c ACPI / OSL: Mark the function acpi_table_checksum() as static ACPI / processor: initialize a variable to silence compiler warning ACPI / processor: use ACPI_COMPANION() to get ACPI device ACPI: correct minor typos ACPI / sleep: Drop redundant acpi_disabled check ACPI / dock: Drop redundant acpi_disabled check ACPI / table: Replace '1' with specific error return values ACPI: remove trailing whitespace ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h> SFI / ACPI: Fix warnings reported during builds with W=1 ... Conflicts: drivers/acpi/nvs.c drivers/hwmon/asus_atk0110.c
2014-01-12ata: pata_samsung_cf: Remove unused macrosSachin Kamat
These macros are not used in the file. Remove them. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-09Merge branch 'for-3.13-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata fixes from Tejun Heo: "Late fixes for libata. Nothing too interesting. Adding missing PM callbacks to satat_sis and an additional PCI ID for ahci" * 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: sata_sis: missing PM support ahci: add PCI ID for Marvell 88SE9170 SATA controller
2014-01-03PCI/MSI: Remove pci_enable_msi_block_auto()Alexander Gordeev
The new pci_msi_vec_count() interface makes pci_enable_msi_block_auto() superfluous. Drivers can use pci_msi_vec_count() to learn the maximum number of MSIs supported by the device, and then call pci_enable_msi_block(). pci_enable_msi_block_auto() was introduced recently, and its only user is the AHCI driver, which is also updated by this change. Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Tejun Heo <tj@kernel.org>
2014-01-02ata: pata_samsung_cf: Use devm_ioremap_resource()Jingoo Han
Use devm_ioremap_resource() in order to make the code simpler, and remove redundant return value check of platform_get_resource() because the value is checked by devm_ioremap_resource(). Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-02ata: pata_samsung_cf: Merge pata_samsung_cf.h into pata_samsung_cf.cSachin Kamat
Since pata_samsung_cf.h is referenced only by pata_samsung_cf.c, merge it into the .c file. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-01sata_sis: missing PM supportAlan
sata_sis has no suspend/resume methods. The default ones will do fine and are needed on some systems. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2013-12-31ahci: add PCI ID for Marvell 88SE9170 SATA controllerSimon Guinot
This patch adds support for the PCI ID provided by the Marvell 88SE9170 SATA controller. Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
2013-12-31ata: pata_samsung_cf: Move plat/regs-ata.h to drivers/ataSachin Kamat
plat/regs-ata.h is used only by Samsung PATA driver. Move this file to the drivers folder to remove platform dependency required for multiplatform support. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Reviewed-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-04-30 16:06:35 +0000