| Age | Commit message (Collapse) | Author |
|---|
|
MAC addresses assigned by the PF to VFs were not kept in the PF driver
admin table. As a result, displaying the VF MACs from the PF interface
to user space showed zero address where in fact the VF got non-zero
address from the PF, fix that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commits e6b6a23 "net/mlx4: Add VF MAC spoof checking support" and
3f7fb021 "net/mlx4: Add set VF default vlan ID and priority support"
missed reporting in the device capabilities dump when these features
are actually supported. Also two too noisy debug messages which produce
message on every QP opened by a VF, were left in the code, fix that.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ndo_set_vf_spoofchk support
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to ndo_set_vf_vlan in the driver. Once this call is used the vport
is considered to be in VST mode. In this mode, the PPF driver configures
Ethernet QPs created by this VF to use this vlan id and priority. Currently
RoCE isn't supported on that mode.
The special values of VID=4095 or VID=0,UP=0 are considered as VGT.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add struct mlx4_vport_state where all the parameters related
to management of VFs port (virtual ports of the NIC eswitch) are kept.
The driver keeps an administrative and operational copy of the settings.
The current administrative copy becomes operational on the event of probing
a VF either on a VM or on the host.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disable timestamp capability on virtual functions.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read HCA frequency, read PCI clock bar and offset, map internal clock to
PCI bar.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new device capability for timestamping support and query FW to retrieve it.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added readable description for the DPDP and port sensing device capabilities.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
not enabled
Older kernels detect DMFS (device-managed flow steering) from the HCA
device capability directly, regardless of whether the capability was
enabled in INIT_HCA, this is fixed by commit 7b8157bed "mlx4_core: Adjustments
to Flow Steering activation logic for SR-IOV"
To protect against guests running kernels without this fix, the host driver
should turn off the DMFS capability bit in mlx4_QUERY_DEV_CAP_wrapper.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband update from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.9:
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle,
Wei Yongjun"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (41 commits)
IB/mlx4: Advertise MW support
IB/mlx4: Support memory window binding
mlx4: Implement memory windows allocation and deallocation
mlx4_core: Enable memory windows in {INIT, QUERY}_HCA
mlx4_core: Disable memory windows for virtual functions
IPoIB: Free ipoib neigh on path record failure so path rec queries are retried
IB/srp: Fail I/O requests if the transport is offline
IB/srp: Avoid endless SCSI error handling loop
IB/srp: Avoid sending a task management function needlessly
IB/srp: Track connection state properly
IB/mlx4: Remove redundant NULL check before kfree
IB/mlx4: Fix compiler warning about uninitialized 'vlan' variable
IB/mlx4: Convert is_xxx variables in build_mlx_header() to bool
IB/iser: Enable iser when FMRs are not supported
IB/iser: Avoid error prints on EAGAIN registration failures
IB/iser: Use proper define for the commands per LUN value advertised to SCSI ML
IB/uverbs: Implement memory windows support in uverbs
IB/core: Add "type 2" memory windows support
mlx4_core: Propagate MR deregistration failures to caller
mlx4_core: Rename MPT-related functions to have mpt_ prefix
...
|
|
Add memory windows-related code to INIT_HCA and QUERY_HCA.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Do not enable memory windows allocation for virtual functions.
In addition, add a few safety checks, such as:
* Verifying the PD of a new MPT matches the VF.
* Making sure binding memory window isn't enabled for FMRs, and
that new memory windows are not FMR themselves.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Mac reassignments should only be done when not supported by the firmware. To
accomplish that, checking firmware capability bit to know whether we should
reassign macs in the driver.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Firmware dynamically changes flow steering hash configuration from covering
L2 only to "full" L2/L3/L4 mode needed. The dynamic change allows the driver
to set hard coded hash configuration which is changed by the firmware from L2
to L2/L3/L4 when attaching the first L3/L4 flow steering rule and back to L2
when there are no more such rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Separate flow steering capability detection from the decision to activate.
For the master (and for native), detect the flow steering capability
in mlx4_dev_cap, but activate the appropriate steering type in a new
function choose_flow_steering() based on detected data.
For VFs, activate flow steering based on what was actually activated
by the master, where that info is obtained via QUERY_HCA. This fixes
the current VF detection which is wrongly based on QUERY_DEV_CAP.
Also, for SR-IOV mode, if flow steering may be activated, do so only
if the max number of QPs per rule is sufficient to satisfy one
subscription per VF. If not, fall back to B0 mode. This is needed to
serve registrations done by L2 network drivers such as mlx4_en and
IPoIB when the network stack attempts to join to multicast groups such
as all-hosts or the IPoIB broadcast group.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
ConnectX-3 devices can use either 64- or 32-byte completion queue
entries (CQEs) and event queue entries (EQEs). Using 64-byte
EQEs/CQEs performs better because each entry is aligned to a complete
cacheline. This patch queries the HCA's capabilities, and if it
supports 64-byte CQEs and EQES the driver will configure the HW to
work in 64-byte mode.
The 32-byte vs 64-byte mode is global per HCA and not per CQ or EQ.
Since this mode is global, userspace (libmlx4) must be updated to work
with the configured CQE size, and guests using SR-IOV virtual
functions need to know both EQE and CQE size.
In case one of the 64-byte CQE/EQE capabilities is activated, the
patch makes sure that older guest drivers that use the QUERY_DEV_FUNC
command (e.g as done in mlx4_core of Linux 3.3..3.6) will notice that
they need an update to be able to work with the PPF. This is done by
changing the returned pf_context_behaviour not to be zero any more. In
case none of these capabilities is activated that value remains zero
and older guest drivers can run OK.
The SRIOV related flow is as follows
1. the PPF does the detection of the new capabilities using
QUERY_DEV_CAP command.
2. the PPF activates the new capabilities using INIT_HCA.
3. the VF detects if the PPF activated the capabilities using
QUERY_HCA, and if this is the case activates them for itself too.
Note that the VF detects that it must be aware to the new PF behaviour
using QUERY_FUNC_CAP. Steps 1 and 2 apply also for native mode.
User space notification is done through a new field introduced in
struct mlx4_ib_ucontext which holds device capabilities for which user
space must take action. This changes the binary interface so the ABI
towards libmlx4 exposed through uverbs is bumped from 3 to 4 but only
when **needed** i.e. only when the driver does use 64-byte CQEs or
future device capabilities which must be in sync by user space. This
practice allows to work with unmodified libmlx4 on older devices (e.g
A0, B0) which don't support 64-byte CQEs.
In order to keep existing systems functional when they update to a
newer kernel that contains these changes in VF and userspace ABI, a
module parameter enable_64b_cqe_eqe must be set to enable 64-byte
mode; the default is currently false.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
and 'srp' into for-linus
|
|
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Previously, the structure of a guest's proxy QPs followed the
structure of the PPF special qps (qp0 port 1, qp0 port 2, qp1 port 1,
qp1 port 2, ...). The guest then did offset calculations on the
sqp_base qp number that the PPF passed to it in QUERY_FUNC_CAP().
This is now changed so that the guest does no offset calculations
regarding proxy or tunnel QPs to use. This change frees the PPF from
needing to adhere to a specific order in allocating proxy and tunnel
QPs.
Now QUERY_FUNC_CAP provides each port individually with its proxy
qp0, proxy qp1, tunnel qp0, and tunnel qp1 QP numbers, and these are
used directly where required (with no offset calculations).
To accomplish this change, several fields were added to the phys_caps
structure for use by the PPF and by non-SR-IOV mode:
base_sqpn -- in non-sriov mode, this was formerly sqp_start.
base_proxy_sqpn -- the first physical proxy qp number -- used by PPF
base_tunnel_sqpn -- the first physical tunnel qp number -- used by PPF.
The current code in the PPF still adheres to the previous layout of
sqps, proxy-sqps and tunnel-sqps. However, the PPF can change this
layout without affecting VF or (paravirtualized) PF code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Remove the error returns for IB ports from mlx4_ib_add,
mlx4_INIT_PORT_wrapper, and mlx4_CLOSE_PORT_wrapper.
Currently, SRIOV is supported only for devices for which the
link layer is IB on all ports; RoCE support will be added later.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Normally, INIT_PORT and CLOSE_PORT are invoked when special QP0
transitions to RTR, or transitions to ERR/RESET respectively.
In SR-IOV mode, however, the master is also paravirtualized. This in
turn requires that we not do INIT_PORT until the entire QP0 path (real
QP0 and proxy QP0) is ready to receive. When the real QP0 goes down,
we should indicate that the port is not active.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
P_Key change and guid change events are not of interest to all slaves,
but only to those slaves which "see" the table slots whose contents
have change.
For example, if the guid at port 1, index 5 has changed in the PPF, we
wish to propagate the gid-change event only to the function which has
that guid index mapped to its port/guid table (in this case it is
slave #5). Other functions should not get the event, since the event
does not affect them.
Similarly with P_Keys -- P_Key change events are forwarded only to
slaves which have that P_Key index mapped to their virtual P_Key table.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
In addition, pass the proxy and tunnel QP numbers to slaves so the
driver can perform special QP paravirtualization.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The wrong offset was used when parsing the number of XRCs in
mlx4_QUERY_DEV_CAP().
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Updates to the qib low-level driver
- First chunk of changes for SR-IOV support for mlx4 IB
- RDMA CM support for IPv6-only binding
- Other misc cleanups and fixes
Fix up some add-add conflicts in include/linux/mlx4/device.h and
drivers/net/ethernet/mellanox/mlx4/main.c
* tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
IB/qib: checkpatch fixes
IB/qib: Add congestion control agent implementation
IB/qib: Reduce sdma_lock contention
IB/qib: Fix an incorrect log message
IB/qib: Fix QP RCU sparse warnings
mlx4: Put physical GID and P_Key table sizes in mlx4_phys_caps struct and paravirtualize them
mlx4_core: Allow guests to have IB ports
mlx4_core: Implement mechanism for reserved Q_Keys
net/mlx4_core: Free ICM table in case of error
IB/cm: Destroy idr as part of the module init error flow
mlx4_core: Remove double function declarations
IB/mlx4: Fill the masked_atomic_cap attribute in query device
IB/mthca: Fill in sq_sig_type in query QP
IB/mthca: Warning about event for non-existent QPs should show event type
IB/qib: Fix sparse RCU warnings in qib_keys.c
net/mlx4_core: Initialize IB port capabilities for all slaves
mlx4: Use port management change event instead of smp_snoop
IB/qib: RCU locking for MR validation
IB/qib: Avoid returning EBUSY from MR deregister
IB/qib: Fix UC MR refs for immediate operations
...
|
|
paravirtualize them
To allow easy paravirtualization of P_Key and GID table sizes, keep
paravirtualized sizes in mlx4_dev->caps, but save the actual physical
sizes from FW in struct: mlx4_dev->phys_cap.
In addition, in SR-IOV mode, do the following:
1. Reduce reported P_Key table size by 1.
This is done to reserve the highest P_Key index for internal use,
for declaring an invalid P_Key in P_Key paravirtualization.
We require a P_Key index which always contain an invalid P_Key
value for this purpose (i.e., one which cannot be modified by
the subnet manager). The way to do this is to reduce the
P_Key table size reported to the subnet manager by 1, so that
it will not attempt to access the P_Key at index #127.
2. Paravirtualize the GID table size to 1. Thus, each guest sees
only a single GID (at its paravirtualized index 0).
In addition, since we are paravirtualizing the GID table size to 1, we
add paravirtualization of the master GID event here (i.e., we do not
do ib_dispatch_event() for the GUID change event on the master, since
its (only) GUID never changes).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Modify mlx4_dev_cap to allow IB support when SR-IOV is active. Modify
mlx4_slave_cap to set the "rdma-supported" bit in its flags area, and
pass that to the guests (this is done in QUERY_FUNC_CAP and its
wrapper).
However, we don't activate IB support quite yet -- we leave the error
return at the start of mlx4_ib_add in the mlx4_ib driver.
In addition, set "protected fmr supported" bit to zero in the
QUERY_FUNC_CAP wrapper.
Finally, in the QUERY_FUNC_CAP wrapper, we needed to add code which
checks for the port type (IB or Ethernet). Previously, this was not
an issue, since only Ethernet ports were supported.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The port management change event can replace smp_snoop. If the
capability bit for this event is set in dev-caps, the event is used
(by the driver setting the PORT_MNG_CHG_EVENT bit in the async event
mask in the MAP_EQ fw command). In this case, when the driver passes
incoming SMP PORT_INFO SET mads to the FW, the FW generates port
management change events to signal any changes to the driver.
If the FW generates these events, smp_snoop shouldn't be invoked in
ib_process_mad(), or duplicate events will occur (once from the
FW-generated event, and once from smp_snoop).
In the case where the FW does not generate port management change
events smp_snoop needs to be invoked to create these events. The flow
in smp_snoop has been modified to make use of the same procedures as
in the fw-generated-event event case to generate the port management
events (LID change, Client-rereg, Pkey change, and/or GID change).
Port management change event handling required changing the
mlx4_ib_event and mlx4_dispatch_event prototypes; the "param" argument
(last argument) had to be changed to unsigned long in order to
accomodate passing the EQE pointer.
We also needed to move the definition of struct mlx4_eqe from
net/mlx4.h to file device.h -- to make it available to the IB driver,
to handle port management change events.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Currently, VFs have 0 in their dev->caps.function field. This is a
valid pci id (usually of the PF). Instead, pass an invalid PCI id to
the VF via QUERY_FW, so that if the value gets accessed in the VF
driver, we'll catch the problem.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The driver is modified to support three operation modes.
If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.
When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.
When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.
Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.
This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.
A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.
B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,
The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "!mlx4_is_slave" is totally confusing. Fix with
constant MLX4_CMD_NATIVE, which is the intended behavior.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- pass the following parameters:
- firmware version (added QUERY_FW paravirtualization for that)
- disable Blueflame on slaves. KVM disables write combining on guests,
and we get better performance without BF in this case. (This requires
QUERY_DEV_CAP paravirtualization, also in this commit)
- max qp rdma as destination
- get rid of a chunk of "if (0)" dead code
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
Fix up trivial conflict in drivers/net/ethernet/emulex/benet/be.h.
* tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (53 commits)
RDMA/cxgb4: Include vmalloc.h for vmalloc and vfree
IB/mlx4: Fix mlx4_ib_add() error flow
IB/core: Fix IB_SA_COMP_MASK macro
IB/iser: Fix error flow in iser ep connection establishment
IB/mlx4: Increase the number of vectors (EQs) available for ULPs
RDMA/cxgb4: Add query_qp support
RDMA/cxgb4: Remove kfifo usage
RDMA/cxgb4: Use vmalloc() for debugfs QP dump
RDMA/cxgb4: DB Drop Recovery for RDMA and LLD queues
RDMA/cxgb4: Disable interrupts in c4iw_ev_dispatch()
RDMA/cxgb4: Add DB Overflow Avoidance
RDMA/cxgb4: Add debugfs RDMA memory stats
cxgb4: DB Drop Recovery for RDMA and LLD queues
cxgb4: Common platform specific changes for DB Drop Recovery
cxgb4: Detect DB FULL events and notify RDMA ULD
RDMA/cxgb4: Drop peer_abort when no endpoint found
RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
mlx4_core: Change bitmap allocator to work in round-robin fashion
RDMA/nes: Don't call event handler if pointer is NULL
RDMA/nes: Fix for the ORD value of the connecting peer
...
|
|
In function mlx4_INIT_PORT_wrapper, the port state mask for the
slave is only set if we are invoking the INIT_PORT fw command.
However, the reference count for the (initialized) port is
incremented anyway.
This creates a problem in that when we have multiple slaves,
then the CLOSE_PORT command will never be invoked. The
reason is that in the CLOSE_PORT wrapper, if the port-state
mask is zero for the slave (which it is), the wrapper returns
without doing anything. The only slave which will not return
immediately in the CLOSE_PORT wrapper is that slave for which
INIT_PORT was invoked.
The fix is to not have the port-state mask setting depend
on the logic for calling the INIT_PORT fw command.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a 64-bit flags2 features member to struct mlx4_dev to
export further features of the hardware. The original flags field
tracks features whose support bits are advertised by the firmware in
offsets 0x40 and 0x44 of the query device capabilities command.
flags2 will track features whose support bits are scattered at various
offsets.
RSS support is the first feature to be exported through flags2. RSS
capabilities are located at offset 0x2e. The size of the RSS
indirection table is also given in this offset.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Removing functions that are no longer in use, but still exist
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At least on powerpc, it breaks the build if exported functions are
static. Fix some static exported functions introduced with the mlx4
SR-IOV support added in 3.3-rc1.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The Virtual Functions should not be aware their function number.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Showing which capabilities are not passed to VF
when executing QUERY_PORT
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the moment VFs can only operate in Eth mode.
In addition we don't want the VF to attempt link sensing,
so we block this option as well.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.
2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
IB or Ethernet.
The driver will use this hint in case the user didn't specify explicitly the link layer
type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
and default the port to link sensing
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Added module parameters sr_iov and probe_vf for controlling enablement of
SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
ports configured as desired.
In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
for the case where the FW supports both port types (ETH and IB), the
port_type_array parameter is used.
By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
VFs obtain their startup information from the PF (master) device via the
comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership: Currently, only one PF is supported by the driver.
If the HCA is burned with FW which enables more than one PF, only one
of the PFs is allowed to run. The first one up grabs a FW ownership
semaphone -- all other PFs will find that semaphore taken, and the
driver will not allow them to run.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the previous implementation mtts are managed by:
1. order - log(mtt segments), 'mtt segment' groups several mtts together.
2. first_seg - segment location relative to mtt table.
In the current implementation:
1. order - log(mtts) rather than segments
2. offset - mtt index in mtt table
Note: The actual mtt allocation is made in segments but it is
transparent to callers.
Rational: The mtt resource holders are not interested on how the allocation
of mtt is done, but rather on how they will use it.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following commands are added here:
1. QUERY_FUNC_CAP and its wrapper. This function is used by VFs when
they start up to receive configuration information from the PF, such
as resource quotas for this VF, which ports should be used (currently
two), what protocol is running on the port (currently Ethernet ONLY,
or port not active).
2. QUERY_PORT and its wrapper. Previously, this FW command was invoked directly
by the ETH driver (en_port.c) using mlx4_cmd_box. Virtualization is now
required here (the VF's MAC address must be substituted for the PFs
MAC address returned by the FW). We changed the invocation
in the ETH driver to use mlx4_QUERY_PORT, and added the wrapper.
3. QUERY_HCA. Used by the VF to determine how the HCA was initialized.
For now, we need only the multicast table member entry size
(log2_mc_table_entry_sz, in the ConnectX PRM). No wrapper is needed
here, because the data may be passed as is to the VF without modification).
In this command, we have added a GLOBAL_CAPS field for passing required
configuration information from FW to a VF (this field is to allow safely
adding new SRIOV capabilities which require support in VF drivers, too).
Bits will set here by FW in response to PF-driver configuration commands which
will activate as yet undefined new SRIOV features. The VF will test to see that
all required capabilities indicated by this field are supported (i.e., if a bit
is set and the VF driver does not recognize that bit, it must abort
its initialization). Currently, no bits are set.
4. Added a CLOSE_PORT wrapper. The PF context needs to keep track of how many VF contexts
have the port open. The PF context will not actually issue the FW close port command
until the last port user issues a CLOSE_PORT request.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).
This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.
Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
|
