Age | Commit message (Collapse) | Author |
|
commit b804eeb6649d75caeccbeae9f5623fc7b8bdfdfa upstream.
The per rate stats should be cleared when aggregation state changes
to avoid making rate scale decisions based on throughput figures which
were collected prior to the aggregation state change and are now stale.
While at it make sure any clearing of the per rate stats will get logged.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ca71f603bb1a0f55e1ba24618ba45617bc36f70 upstream.
instead of duplicating the same loop multiple times,
use a new function for it.
this will be later used also for clearing other
windows in the table.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7bacc782270ff7db3b9f29fa5d24ad2ee1e8e81d upstream.
This feature has been causing trouble - disable it for now.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6bc92803e7f765e02c923cf37c8e280e729642a upstream.
A few entries were wrong and this caused throughput issues.
Fixes: dac94da8dba3 ("iwlwifi: mvm: new BT Coex API")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c4abec0baf25ffb92a28cc99d4231feeaa4d3f3 upstream.
There was a deadlock in monitor mode when we were setting the
channel if the channel was not 1.
======================================================
[ INFO: possible circular locking dependency detected ]
3.14.3 #4 Not tainted
-------------------------------------------------------
iw/3323 is trying to acquire lock:
(&local->chanctx_mtx){+.+.+.}, at: [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211]
but task is already holding lock:
(&local->iflist_mtx){+.+...}, at: [<ffffffffa0609e0a>] ieee80211_set_monitor_channel+0x5a/0x1b0 [mac80211]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&local->iflist_mtx){+.+...}:
[<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0
[<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
[<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0
[<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
[<ffffffffa0518189>] iwl_mvm_recalc_multicast+0x49/0xa0 [iwlmvm]
[<ffffffffa051822e>] iwl_mvm_configure_filter+0x4e/0x70 [iwlmvm]
[<ffffffffa05e6d43>] ieee80211_configure_filter+0x153/0x5f0 [mac80211]
[<ffffffffa05e71f5>] ieee80211_reconfig_filter+0x15/0x20 [mac80211]
[snip]
-> #1 (&mvm->mutex){+.+.+.}:
[<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0
[<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
[<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0
[<ffffffffa0517246>] iwl_mvm_add_chanctx+0x56/0xe0 [iwlmvm]
[<ffffffffa062ca1e>] ieee80211_new_chanctx+0x13e/0x410 [mac80211]
[<ffffffffa062d953>] ieee80211_vif_use_channel+0x1c3/0x5a0 [mac80211]
[<ffffffffa06035ab>] ieee80211_add_virtual_monitor+0x1ab/0x6b0 [mac80211]
[<ffffffffa06052ea>] ieee80211_do_open+0xe6a/0x15a0 [mac80211]
[<ffffffffa0605a79>] ieee80211_open+0x59/0x60 [mac80211]
[snip]
-> #0 (&local->chanctx_mtx){+.+.+.}:
[<ffffffff810d6cb7>] check_prevs_add+0x977/0x980
[<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0
[<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
[<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0
[<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211]
[<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211]
[<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211]
[<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211]
[<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211]
[snip]
other info that might help us debug this:
Chain exists of:
&local->chanctx_mtx --> &mvm->mutex --> &local->iflist_mtx
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&local->iflist_mtx);
lock(&mvm->mutex);
lock(&local->iflist_mtx);
lock(&local->chanctx_mtx);
*** DEADLOCK ***
This deadlock actually occurs:
INFO: task iw:3323 blocked for more than 120 seconds.
Not tainted 3.14.3 #4
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
iw D ffff8800c8afcd80 4192 3323 3322 0x00000000
ffff880078fdb7e0 0000000000000046 ffff8800c8afcd80 ffff880078fdbfd8
00000000001d5540 00000000001d5540 ffff8801141b0000 ffff8800c8afcd80
ffff880078ff9e38 ffff880078ff9e38 ffff880078ff9e40 0000000000000246
Call Trace:
[<ffffffff817ea841>] schedule_preempt_disabled+0x31/0x80
[<ffffffff817ebaed>] mutex_lock_nested+0x19d/0x4f0
[<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
[<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
[<ffffffffa052a680>] ? iwl_mvm_power_mac_update_mode+0xc0/0xc0 [iwlmvm]
[<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
[<ffffffffa0529357>] _iwl_mvm_power_update_binding+0x27/0x80 [iwlmvm]
[<ffffffffa0516eb1>] iwl_mvm_unassign_vif_chanctx+0x81/0xc0 [iwlmvm]
[<ffffffffa062d3ff>] __ieee80211_vif_release_channel+0xdf/0x470 [mac80211]
[<ffffffffa062e2fa>] ieee80211_vif_release_channel+0x4a/0xb0 [mac80211]
[<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211]
[<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211]
[<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211]
[<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211]
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75541
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83f7a85f1134c6e914453f5747435415a23d516b upstream.
In case RFKILL is in KILL position, the NIC will issue an
interrupt straight away. This interrupt won't be sent
because it is masked in the hardware.
But if our interrupt service routine is called for another
reason (SHARED_IRQ), then we'll look at the interrupt cause
and service it. This can cause bad things if we are not
ready yet.
Explicitly clean the interrupt cause register to make sure
we won't service anything before we are ready to.
Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0229cdafb6f67064a217591d48b0f6abf14e8385 upstream.
If we have no beacon data before association, delay smart FIFO
enablement until after we have this data.
Not doing so can cause association failures in extremely silent
environments (usually only a shielded box/room) as beacon RX is
not sent to the host immediately, and then the association time
event ends without the host receiving any beacon even though it
was on the air - it's just stuck on the FIFO.
Fixes: 1f3b0ff8ecce ("iwlwifi: mvm: Add Smart FIFO support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 431031851ea72a25abb9ad4df56a0f3b997e3026 upstream.
This will allow to load the new firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 87d5e4155c0088e6766b4f0193b63fa0eab71220 upstream.
After being idle for a long time (>5sec) the rs statistics
will be stale so we prefer to reset rs and start from legacy
rates again. This gives better results when the attenuation
increased signficantly (e.g. we got further from the AP) and
after a while we start Tx
Note that the first Tx after the idle period will still go out
in the old modulation and rate but this seemed a simpler approach
compared to adding a timer or modifying mac80211 for this.
The negative impact is negligble as we'll recover quickly.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e53839eb9882c99d3781eab0fe1b2d4369a6a2cc upstream.
Change the down/upscale decision logic a bit to be based
on different success ratio thresholds. This fixes the implementation
compared to the rate scale algorithm which was planned to yield
optimal results. Also fix a case where a lower rate wasn't explored
despite being a potential for better throughput.
While at it rewrite rs_get_rate_action to be more clear and clean.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8fff919ecd7820084675c2814913445e95640ac upstream.
Don't search columns which are unlikely to succeed as previous
columns searched with less aggressive modulation failed.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fd7dbee51b3d98402edb11fec0c93d96476e0ae1 upstream.
Allow switching back to legacy Tx columns so we'll stop doing
HT/VHT in case we're far from the AP. Stop active aggregation when
making a deciding to stay in a legacy column.
Despite having low legacy rates in the LQ table lower entries
it doesn't help much in case we're doing aggregations as the
aggregation was being transmitted in the initial rate of the table.
This should help traffic stalls when far from the AP.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 80f2679e589503bd6cbaaa1f9c1cd9dd7dfae032 upstream.
Add 2 new HW IDs for the 7265 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9088f60425e0acd8a8f05fdfcfdd288d3258641 upstream.
mimo_delim was always set to 0 instead of pointing to
the first SISO entry after MIMO rates.
This can cause keep transmitting in MIMO even when we shouldn't.
For example when the peer is requesting static SMPS.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08a732f4e4a842f0101e5ea03d79e9d613ffadbe upstream.
It was missing.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a82dda6cd492b8c88952be6f6527f3656f7ac585 upstream.
The current firmware advertises support for uAPSD, but
critical bugs force us to disable the feature.
When a fixed firmware will be available, we will be able to
re-enable uAPSD.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82e5a649453a3cf23516277abb84273768a1592b upstream.
There is a flow in which we send the host command in SYNC
mode, but we don't take priv->mutex.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1046495
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8930b05090acd321b1fc7c642528c697cb105c42 upstream.
We should explore all possible columns when searching to be
as resilient as possible to changing conditions. This fixes
for example a scenario where even after a sudden creation of
rssi difference between the 2 antennas we would keep doing MIMO
at a low rate instead of switching to SISO at a higher rate using
the better antenna which was the optimal configuration.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update of the HW IDs for the 7265 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Since the statistics handler is asynchrous, it can very well
be that we will handle the statistics (hence the RSSI
fluctuation) when we already disassociated.
Don't WARN on this case.
This solves: https://bugzilla.redhat.com/show_bug.cgi?id=1071998
Cc: <stable@vger.kernel.org> [3.10+]
Fixes: 2b76ef13086f ("iwlwifi: mvm: implement reduced Tx power")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Only the first packet is currently handled correctly, but then
all others are assumed to have failed which is problematic. Fix
this, marking them all successful instead (since if they're not
then the firmware will have transmitted them as single frames.)
This fixes the lost packet reporting.
Also do a tiny variable scoping cleanup.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[Add the dvm part]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Some APs reject STA association request if a listen interval value exceeds
a threshold of 10. Thus, for example, Cisco APs may deny STA associations
returning status code 12 (Association denied due to reason outside the scope
of 802.11 standard) in the association response frame.
Fixing the issue by setting the default IWL_CONN_MAX_LISTEN_INTERVAL value
from 70 to 10.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
We set IWL_STA_UCODE_INPROGRESS flag when we add a station
and clear it when we send the LQ command for it. But the LQ
command is sent only when the association succeeds.
If the association doesn't succeed, we would leave this flag
set and that wouldn't indicate the station entry as vacant.
This probably fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1065663
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
NICs supported by iwldvm don't handle well TX AMPDU.
Disable it by default, still leave the possibility to
the user to force enable it with a debug parameter.
NICs supported by iwlmvm don't suffer from the same issue,
leave TX AMPDU enabled by default for these.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The driver wasn't reading the NVM properly. While this
didn't lead to any issue until now, it seems that there
is an old version of the NVM in the wild.
In this version, the A band channels appear to be valid
but the SKU capabilities (another field of the NVM) says
that A band isn't supported at all.
With this specific version of the NVM, the driver would
think that A band is supported while the HW / firmware
don't. This leads to asserts.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Not doing so will let BT kill our probe requests leading to
failures in scan.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
We had a bug that prevented us from removing a station
after we entered the drain flow:
We assign sta to be NULL if it was an error value.
Then we tested it against -EBUSY, but forget to retrieve
the value again from mvm->fw_id_to_mac_id[sta_id].
Due to this bug, we ended up never removing the STA from
the firmware. This led to an firmware assert when we remove
the GO vif.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Configure scheduled scan to notify match found on every beacon
or probe response if the scan request doesn't contain valid ssid
list for filtering.
Without this configuration the FW passes all beacons to the host
but doesn't notify the stack that the scan results are ready for
processing.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add 6 new HW IDs for the 7265 series.
Cc: <stable@vger.kernel.org> [3.13]
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This can be useful to be able to spot the firmware version
from the error reports without needing to fetch it from
another place.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The iwlwifi scheduled scan implementation doesn't adhere to the
userspace API correctly - the API assumes that any new incoming
'incompatible' request (like scan or remain-on-channel for this
driver) will just cancel the scheduled scan. Instead our driver
relies on userspace cancelling it, thus breaking existing wpa_s
versions.
Cc: stable@vger.kernel.org [3.13]
Fixes: 35a000b7c1bb ("iwlwifi: mvm: support sched scan if supported by the fw")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The address pointer used in the function shouldn't be static
since it's local data only. Having it static causes races if
a single machine has two devices, as the pointer would be
shared between instances.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
|
|
None of the devices supported by iwldvm have support for
shadow registers. This means that we wake the NIC
when we increment the write pointer on Tx ring.
This happened even before my bad commit mentionned below.
Since my commit below, we wake up the NIC when we put a
host command on the ring regardless of shadow register
support. This means that in iwldvm (when the NIC doesn't
support shadow register), we wake up the NIC twice:
pcie_enqueue_hcmd:
wake up the NIC
iwl_pcie_txq_inc_wr_ptr:
wake up the NIC - no shadow reg support
Since waking up the NIC means that we need to acquire a
spinlock, this obviously leads to a recursive spinlock
and hence a freeze.
Fixes: b9439491055a ("iwlwifi: pcie: keep the NIC awake when commands are in flight")
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
|
|
|
|
Keeping this as 0 is ok according to spec section 9.7.11
as this means the limits are according to the Tx/Rx
supported MCS x NSS bitmap. Initially we've set these as
there were concerns of interop issues but these turned out
to be false.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
If we try to write NVM that do not exist, the function will return
uninitialized value. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)
While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
All beamformee supporting chips have the ability to support
VHT NDP in up to 4 STSs. So change the published beamformee
STS cap accordingly to 3 as it should be Nsts-1.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The request of SMPS issued by the Thermal Throttling code
was not reset when we disassociated - fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
It's a bit strange to treat an array as a pointer, so use proper
array indexing instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
If the length isn't set it means we want all the SRAM.
Also - this is perfectly valid to partially dump starting
at offset 0.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Discovered by klocwork
Array 'iwl_rate_mcs' of size 15 may use index value(s) -1
* rs.c:2562: index = iwl_hwrate_to_plcp_idx(rate)
* rs.c:2562: Result of function call 'iwl_hwrate_to_plcp_idx(rate)' is '[-1,14]'
* rs.c:2565: Array 'iwl_rate_mcs' size is 15.
* rs.c:2565: Possible attempt to access element -1 of array 'iwl_rate_mcs'.
While at it stop using index = -1 and always use IWL_RATE_INVALID
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Some NIC comes with more than the 4 NVM (non volative
memory) sections described in the nvm_to_read array.
These NICs usually get their NVM from an external file
fetched from userland during init.
We already parsed the file, but sent to the NIC only 4 NVM
sections whereas there could be more sections in the file.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Since seq_number is incremented right after using
it, so printed seq_ctrl was actually the next
one to be used.
Fix it by incrementing the seq_number only later,
before saving it.
Additionally, use the IEEE80211_SEQ_TO_SN macro
in order to print the actual sequence number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|