aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2013-06-04tg3: Add read dma workaround for 5720Nithin Sujir
Commit 091f0ea30074bc43f9250961b3247af713024bc6 "tg3: Add New 5719 Read DMA workaround" added a workaround for TX DMA stall on the 5719. This workaround needs to be applied to the 5720 as well. Cc: stable@vger.kernel.org Reported-by: Roland Dreier <roland@purestorage.com> Tested-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net: ethernet: xilinx_emaclite: set protocol selector bits when writing ANARJens Renner \(EFE\)
This patch sets the protocol selector bits (4:0) of the PHY's MII_ADVERTISE register (ANAR) when writing ADVERTISE_ALL. The protocol selector bits are indicating IEEE 803.3u support and are fixed / read-only on some PHYs. Not setting them correctly on others (like TI DP83630) makes the PHY fall back to 10M HDX mode which should be avoided. Tested for TI DP83630 PHY on Microblaze platform. Signed-off-by: Jens Renner <renner@efe-gmbh.de> Tested-by: Michal Simek <monstr@monstr.eu> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04bnx2x: Fix bridged GSO for 57710/57711 chipsYuval Mintz
It was recently found out that GSO on 57710/57711 was broken, due to packets being sent without a valid IP checksum. Commit 057cf65 "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this issue, but failed to set the correct IP checksum when receiving GSO packets via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed to calculate IP checksum were erroneously set in the incorrect buffer descriptor. This patch re-enables GSO in said scenario for 57710/57711 chips. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net: fec: add fallback to random MAC addressLucas Stach
If no valid MAC address could be obtained from the hardware, fall back to a randomly generated one. Signed-off-by: Pavel Machek <pavel@denx.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04bnx2x: fix TCP offload for tunneling ipv4 over ipv6Dmitry Kravkov
FW was initialized with data from wrong header, this caused TSO packets have wrong IP csum. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04Merge branch 'fixes-for-3.10' of git://gitorious.org/linux-can/linux-canDavid S. Miller
Marc Kleine-Budde says: ==================== here are there fixes for the v3.10 release cycle: The first patch by Jonas Peterson and Olivier Sobrie fixes the reception of CAN frames on Kvaser's "USBcan Pro" and "USBcan R" type hardware. The last two patches by Olivier Sobrie (for esd_usb2) and me (for peak_usb) change the memory handling for the USB messages from stack to kmalloc(), as memory used for DMA should not be allocated on stack. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net/mlx4_core: Keep VF assigned MAC in the PF admin tableOr Gerlitz
MAC addresses assigned by the PF to VFs were not kept in the PF driver admin table. As a result, displaying the VF MACs from the PF interface to user space showed zero address where in fact the VF got non-zero address from the PF, fix that. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net/mlx4_en: Handle unassigned VF MAC address correctlyOr Gerlitz
When a VF sense they didn't get MAC address, use random one. This will address the case of administrator not assigning MAC to the VF through the PF OS APIs and keep udev happy. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net/mlx4_core: Return -EPROBE_DEFER when a VF is probed before PF is ↵Jack Morgenstein
sufficiently initialized In the PF initialization, SRIOV is enabled before the PF is fully initialized. This allows the kernel to probe the newly-exposed VFs before the PF is ready to handle them (nested probes). Have the probe method return the -EPROBE_DEFER value in this situation (instead of the VF probe method retrying its initialization in a loop, and returning -EIO on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel itself will retry the probe after a suitable delay. Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04net/mlx4_en: Fix adaptive moderation cq updateSagi Grimberg
When turning on adaptive_rx under adaptive moderation, the CQ's moderation count wasn't updated according to rx_frames which resulted in too many interrupts and bandwidth drop. Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-03net: can: peak_usb: Do not do dma on the stackMarc Kleine-Budde
smatch reports the following warnings: drivers/net/can/usb/peak_usb/pcan_usb_pro.c:514 pcan_usb_pro_drv_loaded() error: doing dma on the stack (buffer) drivers/net/can/usb/peak_usb/pcan_usb_pro.c:878 pcan_usb_pro_init() error: doing dma on the stack (&fi) drivers/net/can/usb/peak_usb/pcan_usb_pro.c:889 pcan_usb_pro_init() error: doing dma on the stack (&bi) See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?" Cc: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-06-03net: can: esd_usb2: Do not do dma on the stackOlivier Sobrie
smatch reports the following warnings: drivers/net/can/usb/esd_usb2.c:640 esd_usb2_start() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:846 esd_usb2_close() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:855 esd_usb2_close() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:923 esd_usb2_set_bittiming() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:1047 esd_usb2_probe() error: doing dma on the stack (&msg) drivers/net/can/usb/esd_usb2.c:1053 esd_usb2_probe() error: doing dma on the stack (&msg) See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?" Signed-off-by: Olivier Sobrie <olivier@sobrie.be> Cc: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-06-03net: can: kvaser_usb: fix reception on "USBcan Pro" and "USBcan R" type ↵Jonas Peterson
hardware. Unlike Kvaser Leaf light devices, some other Kvaser devices (like USBcan Pro, USBcan R) receive CAN messages in CMD_LOG_MESSAGE frames. This patch adds support for it. Cc: linux-stable <stable@vger.kernel.org> # >= v3.8 Signed-off-by: Jonas Peterson <jonas.peterson@gmail.com> Signed-off-by: Olivier Sobrie <olivier@sobrie.be> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-05-31hyperv: Fix vlan_proto setting in netvsc_recv_callback()Haiyang Zhang
Since the recent addition of 8021AD, we need to set the new field vlan_proto in sk_buff. Otherwise, it will trigger BUG() call in vlan_proto_idx(). This patch fixes the problem. Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-31team: fix port list dump for big number of portsJiri Pirko
In case the port list dump does not fit into one skb currently the dump would start over again. Fix this by continue from the last dumped port. Introduced by commit d90f889e9c (team: handle sending port list in the same way option list is sent) Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-31Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless John W. Linville says: ==================== Please pull this batch of fixes intended for the 3.10 stream... Regarding the NFC bits, Samuel says: "This is the first batch of NFC fixes for 3.10, and it contains: - 3 fixes for the NFC MEI support: * We now depend on the correct Kconfig symbol. * We register an MEI event callback whenever we enable an NFC device, otherwise we fail to read anything after an enable/disable cycle. * We only disable an MEI device from its disable mey_phy_ops, preventing useless consecutive disable calls. - An NFC Makefile cleanup, as I forgot to remove a commented out line when moving the LLCP code to the NFC top level directory." As for the mac80211 bits, Johannes says: "This time I have a fix from Stanislaw for a stupid mistake I made in the auth/assoc timeout changes, a fix from Felix for 64-bit traffic counters and one from Helmut for address mask handling in mac80211. I also have a few fixes myself for four different crashes reported by a few people." And Johannes says this about the iwlwifi bit: "This fixes a brown paper-bag bug that we really should've caught in review. More details in the changelog for the fix." On top of that... Arend van Spriel and Hante Meuleman cooperate to send a series of AP and P2P mode fixes for brcmfmac. Gabor Juhos corrects a register offset for AR9550, avoiding a bus error. Dan Carpenter provides a fixup to some dmesg output in the atmel driver. And, finally... Felix Fietkau not only gives us a trio of small AR934x fixes, but also refactors the ath9k aggregation session start/stop handling (using the generic mac80211 support) in order to avoid a deadlock. Please let me know if there are problems! ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-30be2net: Fix crash on 2nd invocation of PCI AER/EEH error_detected hookSomnath Kotur
During a PCI EEH/AER error recovery flow, if the device did not successfully restart, the error_detected() hook may be called a second time with a "perm_failure" state. This patch skips over driver cleanup for the second invocation of the callback. Also, Lancer error recovery code is fixed-up to handle these changes. Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Somnath kotur <somnath.kotur@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-30be2net: Mark checksum fail for IP fragmented packetsSomnath Kotur
HW does not compute L4 checksum for IP Fragmented packets. Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-29Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2013-05-29tuntap: forbid changing mq flag for persistent deviceJason Wang
We currently allow changing the mq flag (IFF_MULTI_QUEUE) for a persistent device. This will result a mismatch between the number the queues in netdev and tuntap. This is because we only allocate a 1q netdevice when IFF_MULTI_QUEUE was not specified, so when we set the IFF_MULTI_QUEUE and try to attach more queues later, netif_set_real_num_tx_queues() may fail which result a single queue netdevice with multiple sockets attached. Solve this by disallowing changing the mq flag for persistent device. Bug was introduced by commit edfb6a148ce62e5e19354a1dcd9a34e00815c2a1 (tuntap: reduce memory using of queues). Reported-by: Sriram Narasimhan <sriram.narasimhan@hp.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-28ath9k: use correct OTP register offsets for AR9550Gabor Juhos
Accessing the OTP memory on AR9950 causes a data bus like this: Data bus error, epc == 801f7774, ra == 801f7774 Oops[#1]: CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc3 #592 task: 87c28000 ti: 87c22000 task.ti: 87c22000 $ 0 : 00000000 00000061 deadc0de 00000000 $ 4 : b8115f18 00015f18 00000007 00000004 $ 8 : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c $12 : 7c7c3c7c 80320a68 00000000 7c7c7c3c $16 : 87cd8010 00015f18 00000007 00000000 $20 : 00000064 00000004 87c23c7c 8035210c $24 : 00000000 801f3674 $28 : 87c22000 87c23b48 00000001 801f7774 Hi : 00000000 Lo : 00000064 epc : 801f7774 ath9k_hw_wait+0x58/0xb0 Not tainted ra : 801f7774 ath9k_hw_wait+0x58/0xb0 Status: 1000cc03 KERNEL EXL IE Cause : 4080801c PrId : 00019750 (MIPS 74Kc) Modules linked in: Process swapper (pid: 1, threadinfo=87c22000, task=87c28000, ts=00000000) Stack : 0000000f 00000061 00002710 8006240c 00000001 87cd8010 87c23bb0 87cd8010 00000000 00000004 00000003 80210c7c 000000b3 67fa8000 0000032a 000006fe 000003e8 00000002 00000028 87c23bf0 000003ff 80210d24 803e5630 80210e28 00000000 00000007 87cd8010 00007044 00000004 00000061 000003ff 000001ff 87c26000 87cd8010 00000220 87cd8bb8 80210000 8020fcf4 87c22000 87c23c08 ... Call Trace: [<801f7774>] ath9k_hw_wait+0x58/0xb0 [<80210c7c>] ar9300_otp_read_word+0x80/0xd4 [<80210d24>] ar9300_read_otp+0x54/0xb0 [<8020fcf4>] ar9300_check_eeprom_header+0x1c/0x40 [<80210fe4>] ath9k_hw_ar9300_fill_eeprom+0x118/0x39c [<80206650>] ath9k_hw_eeprom_init+0x74/0xb4 [<801f96d0>] ath9k_hw_init+0x7ec/0x96c [<801e65ec>] ath9k_init_device+0x340/0x758 [<801f35d0>] ath_ahb_probe+0x21c/0x2c0 [<801c041c>] driver_probe_device+0xc0/0x1e4 [<801c05ac>] __driver_attach+0x6c/0xa4 [<801bea08>] bus_for_each_dev+0x64/0xa8 [<801bfa40>] bus_add_driver+0xcc/0x24c [<801c0954>] driver_register+0xbc/0x17c [<803f8fc0>] ath9k_init+0x5c/0x88 [<800608fc>] do_one_initcall+0xec/0x1a0 [<803e6a68>] kernel_init_freeable+0x13c/0x200 [<80309cdc>] kernel_init+0x1c/0xe4 [<80062450>] ret_from_kernel_thread+0x10/0x18 On the AR9550, the OTP registers are located at the same address as on the AR9340. Use the correct values to avoid the error. Cc: stable@vger.kernel.org # 3.6+ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-28brcmfmac: Disable powersave mode for P2P link.Hante Meuleman
For p2p client mode powersave mode should be kept disabled. It is working but inefficient. In general p2p links do no benefit from this mode, because these links are setup temporarily to transfer data. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-28brcmfmac: Add multi channel support for P2P.Hante Meuleman
Multi channel support was disabled. This patch will enable it and configure the P2P GO on the correct frequency when multi channel is used. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-28brcmfmac: use struct net_device::destructor to remove interfacesArend van Spriel
Upon deleting a P2P_CLIENT/GO interface the vif and consequently the wdev is freed before the net_device is actually being unregistered but cfg80211 still needs to access the wdev. Using destructor field to free the net_device and vif. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-28brcmfmac: free net device when registration failsArend van Spriel
When registration fails the net device is no longer needed. Free the net device and remove reference to private data from the driver. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-28brcmfmac: add additional parameter to brcmf_free_vif()Arend van Spriel
Pass the struct brcmf_cfg80211_info instance instead of obtaining through vif itself using vif->wdev. This is needed as the netdev associated with this vif is already unregistered. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-28brcmfmac: Fix p2p setup when connected to ap on 5G.Hante Meuleman
The firmware requires that on p2p setup when net interfaces are created or updated that they start initially with the same channel as the channel in use for the current connection (if any). If none exists take default channel 11. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-28brcmfmac: Turn off ARP offloading when configured for AP.Hante Meuleman
ARP offloading should only be used in STA or P2P client mode. It is currently configured once at init. When being configured for AP ARP offloading should be turned off and when AP mode is left it can be turned back on. Cc: stable@vger.kernel.org Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-28Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
2013-05-27net: phy: fix a bug when verify the EEE supportGiuseppe CAVALLARO
The phy_init_eee has to exit with an error when the local device and its link partner both do not support EEE. So this patch fixes a problem when verify this. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-27iwlwifi: dvm: fix zero LQ CMD sending avoidanceEmmanuel Grumbach
In 63b77bf489881747c5118476918cc8c29378ee63 iwlwifi: dvm: don't send zeroed LQ cmd I tried to avoid to send zeroed LQ cmd, but I made a (very) stupid mistake in the memcmp. Since this patch has been ported to stable, the fix should go to stable too. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341 Cc: stable@vger.kernel.org Reported-by: Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-25qlge: add missing free_netdev() on error in qlge_probe()Wei Yongjun
Add the missing free_netdev() before return from function qlge_probe() in the error handling case. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-24ath9k_hw: improve performance for AR934x v1.3+Felix Fietkau
AR934x v1.3 no longer needs the DCU backoff reduction workaround for preventing rx overruns, but in turn needs the number of usable Tx buffers to be reduced slightly. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-24ath9k_hw: fix host interface reset on AR934xFelix Fietkau
If a local bus timeout has been detected, the host interface needs to be reset to clear the errors. AR934x uses a different synchronous interrupt bit to indicate this, so the check needs to be fixed. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-24ath9k_hw: fix spur mitigation issues on AR934xFelix Fietkau
Do not subtract spur power from noise floor on this chip, as it can lead to packet loss and other connectivity issues. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: "It's been a while since my last pull request so quite a few fixes have piled up." Indeed. 1) Fix nf_{log,queue} compilation with PROC_FS disabled, from Pablo Neira Ayuso. 2) Fix data corruption on some tg3 chips with TSO enabled, from Michael Chan. 3) Fix double insertion of VLAN tags in be2net driver, from Sarveshwar Bandi. 4) Don't have TCP's MD5 support pass > PAGE_SIZE page offsets in scatter-gather entries into the crypto layer, the crypto layer can't handle that. From Eric Dumazet. 5) Fix lockdep splat in 802.1Q MRP code, also from Eric Dumazet. 6) Fix OOPS in netfilter log module when called from conntrack, from Hans Schillstrom. 7) FEC driver needs to use netif_tx_{lock,unlock}_bh() rather than the non-BH disabling variants. From Fabio Estevam. 8) TCP GSO can generate out-of-order packets, fix from Eric Dumazet. 9) vxlan driver doesn't update 'used' field of fdb entries when it should, from Sridhar Samudrala. 10) ipv6 should use kzalloc() to allocate inet6 socket cork options, otherwise we can OOPS in ip6_cork_release(). From Eric Dumazet. 11) Fix races in bonding set mode, from Nikolay Aleksandrov. 12) Fix checksum generation regression added by "r8169: fix 8168evl frame padding.", from Francois Romieu. 13) ip_gre can look at stale SKB data pointer, fix from Eric Dumazet. 14) Fix checksum handling when GSO is enabled in bnx2x driver with certain chips, from Yuval Mintz. 15) Fix double free in batman-adv, from Martin Hundebøll. 16) Fix device startup synchronization with firmware in tg3 driver, from Nithin Sujit. 17) perf networking dropmonitor doesn't work at all due to mixed up trace parameter ordering, from Ben Hutchings. 18) Fix proportional rate reduction handling in tcp_ack(), from Nandita Dukkipati. 19) IPSEC layer doesn't return an error when a valid state is detected, causing an OOPS. Fix from Timo Teräs. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits) be2net: bug fix on returning an invalid nic descriptor tcp: xps: fix reordering issues net: Revert unused variable changes. xfrm: properly handle invalid states as an error virtio_net: enable napi for all possible queues during open tcp: bug fix in proportional rate reduction. net: ethernet: sun: drop unused variable net: ethernet: korina: drop unused variable net: ethernet: apple: drop unused variable qmi_wwan: Added support for Cinterion's PLxx WWAN Interface perf: net_dropmonitor: Remove progress indicator perf: net_dropmonitor: Use bisection in symbol lookup perf: net_dropmonitor: Do not assume ordering of dictionaries perf: net_dropmonitor: Fix symbol-relative addresses perf: net_dropmonitor: Fix trace parameter order net: fec: use a more proper compatible string for MVF type device qlcnic: Fix updating netdev->features qlcnic: remove netdev->trans_start updates within the driver qlcnic: Return proper error codes from probe failure paths tg3: Update version to 3.132 ...
2013-05-23be2net: bug fix on returning an invalid nic descriptorWei Yang
In function be_get_nic_desc(), it will go through the descriptor array returned from f/w. By comparing the desc_type field, it determines whether there is a nic descriptor in the array or not. In the case of no nic descriptor, this function should return NULL. The code may return an invalide descriptor, when there is no nic descriptor in the array and the desc_count is less than MAX_RESOURCE_DESC. In this case, even there is no nic descriptor, it will still return the lase descriptor since the i doesn't equal to MAX_RESOURCE_DESC. This patch fix this issue by returning the descriptor when find it and return NULL for other cases. Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com> Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com> Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Acked-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-23net: Revert unused variable changes.David S. Miller
This reverts commits: c573972c111eb4c6b3f3250ad71e7c75cc799833 1a5904342c7380ceddd61c0b37544d752d0b1433 da2e2c214953f37c2a6be20226537ca5a329724c They were meant for net-next not net. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-23Merge tag 'usb-3.10-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg Kroah-Hartman: "Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2 The majority of these are USB gadget fixes, but they are all small. Other than that, some USB host controller fixes, and USB serial driver fixes for problems reported with them. Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems to be almost impossible to get right for all of the different platforms these days." * tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (56 commits) USB: cxacru: potential underflow in cxacru_cm_get_array() USB: ftdi_sio: Add support for Newport CONEX motor drivers USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN card usb: ohci: fix goto wrong tag in err case usb: isp1760-if: fix memleak when platform_get_resource fail usb: ehci-s5p: fix memleak when fallback to pdata USB: serial: clean up chars_in_buffer USB: ti_usb_3410_5052: fix chars_in_buffer overhead USB: io_ti: fix chars_in_buffer overhead USB: ftdi_sio: fix chars_in_buffer overhead USB: ftdi_sio: clean up get_modem_status USB: serial: add generic wait_until_sent implementation USB: serial: add wait_until_sent operation USB: set device dma_mask without reference to global data USB: Blacklisted Cinterion's PLxx WWAN Interface usb: option: Add Telewell TW-LTE 4G USB: EHCI: remove bogus #error USB: reset resume quirk needed by a hub USB: usb-stor: realtek_cr: Fix compile error usb, chipidea: fix link error when USB_EHCI_HCD is a module ...
2013-05-23virtio_net: enable napi for all possible queues during openJason Wang
Commit 55257d72bd1c51f25106350f4983ec19f62ed1fa (virtio-net: fill only rx queues which are being used) only does the napi enabling during open for curr_queue_pairs. This will break multiqueue receiving since napi of new queues were still disabled after changing the number of queues. This patch fixes this by enabling napi for all possible queues during open. Cc: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22net: ethernet: sun: drop unused variableEmilio López
Commit bfd428d ("net: ethernet: sun: initialize variables directly") dropped the only loop that was using i but did not remove the actual variable, therefore causing a warning when building. This patch drops the now redundant line. Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22net: ethernet: korina: drop unused variableEmilio López
Commit e998fd4 ("net: ethernet: korina: initialize variables directly") dropped the only loop that was using i but did not remove the actual variable, therefore causing a warning when building. This patch drops the now redundant line. Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22net: ethernet: apple: drop unused variableEmilio López
Commit 3b0aaef ("net: ethernet: apple: initialize variables directly") dropped the only loop that was using i but did not remove the actual variable, therefore causing a warning when building. This patch drops the now redundant line. Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22qmi_wwan: Added support for Cinterion's PLxx WWAN InterfaceHans-Christoph Schemmel
Added support for Cinterion's PLxx WWAN Interface by adding QMI_FIXED_INTF with Cinterion's Vendor ID as well as Product ID and WWAN Interface Number. Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com> Signed-off-by: Christian Schmiedl <christian.schmiedl@gemalto.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22net: fec: use a more proper compatible string for MVF type deviceShawn Guo
MVF is a family while MVF600 is a particular SoC in the family. We generally prefer to use SoC rather than family name in compatible string to define a particular type of fec device. And this is how fec_dt_ids works for all those IMX fec variants. Let's change mvf to mvf600 to have it work in the same way. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22qlcnic: Fix updating netdev->featuresShahed Shaikh
o After change in EPORT features of 82xx adapter, netdev->features needs to be updated to reflect EPORT feature updates but driver was manipulating netdev->features at wrong place. o This patch uses netdev_update_features() and .ndo_fix_features() to update netdev->features properly. Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22qlcnic: remove netdev->trans_start updates within the driverSony Chacko
Code is removed because netdev->trans_start updates made by the driver will be ignored by the kernel. Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22qlcnic: Return proper error codes from probe failure pathsSony Chacko
Fix error paths in probe to assign proper error codes to probe return value. Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22tg3: Update version to 3.132Nithin Sujir
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22tg3: Ensure boot code has completed initialization before accessing hardwareNithin Sujir
After resetting the device, the driver waits for a signature to be updated to know that firmware has completed initialization. However, the call to tg3_poll_fw() is being done too late and we're writing to the GRC_MODE register before it has completely initialized, causing contention with firmware. This logic has existed since day one but is causing PCIE link to go down randomly at startup on one platform once every few hundred reboots. Move the tg3_poll_fw() up to before we write to the GRC_MODE register after reset. Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-22 16:04:35 +0000