| Age | Commit message (Collapse) | Author |
|---|
|
commit a1e1774c6dfa3a524dd8df51ca95185fe5ef3247 upstream.
When compiled with CONFIG_DEBUG_SG set, uninitialized SGL leads
to BUG() in compare_and_write_callback().
Signed-off-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When copying between device and command protection scatters
we must take into account that device scatters might be offset
and we might copy outside scatter range. Thus for each cmd prot
scatter we must take the min between cmd prot scatter, dev prot
scatter, and whats left (and loop in case we havn't copied enough
from/to cmd prot scatter).
Example (single t_prot_sg of len 2048):
kernel: sbc_dif_copy_prot: se_cmd=ffff880380aaf970, left=2048, len=2048, dev_prot_sg_offset=3072, dev_prot_sg_len=4096
kernel: isert: se_cmd=ffff880380aaf970 PI error found type 0 at sector 0x2600 expected 0x0 vs actual 0x725f, lba=2580
Instead of copying 2048 from offset 3072 (copying junk outside sg
limit 4096), we must to copy 1024 and continue to next sg until
we complete cmd prot scatter.
This issue was found using iSER T10-PI offload over rd_mcp (wasn't
discovered with fileio since file_dev prot sglists are never offset).
Changes from v1:
- Fix sbc_copy_prot copy length miss-calculation
Changes from v0:
- Removed psg->offset consideration for psg_len computation
- Removed sg->offset consideration for offset condition
- Added copied consideraiton for len computation
- Added copied offset to paddr when doing memcpy
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Because then this sg is passed to sbc_copy_prot which will
hit a protection fault in cases we have more than a single sg.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug in sbc_dif_copy_prot() where the updated addr
offset did not take into account the case where the associated
scatterlist had not been incremented.
This addresses the case where incoming protection scatterlists may
contain a length smaller than PAGE_SIZE across multiple entires,
when the target protection scatterlists are always being explicitly
filled up to PAGE_SIZE before adding another entry.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Need to take into account that protection sg_list
(copy-buffer) may consist of multiple entries.
Changes from v0:
- Changed commit description
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
SPC-4 states that data-integrity errors shall also report
the failed sector in CHECK_CONDITION response sense data
information field.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch updates sbc_emulate_readcapacity_16() to set
P_TYPE and PROT_EN bits when DIF emulation is enabled by
the backend device.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds support for DIF read/write verify emulation
for TARGET_DIF_TYPE1_PROT + TARGET_DIF_TYPE3_PROT operation.
This includes sbc_dif_verify_write() + sbc_dif_verify_read()
calls accessable by backend drivers to perform DIF verify
for SGL based data and protection information.
Also included is sbc_dif_copy_prot() logic to copy protection
information to/from backend provided protection SGLs.
Based on scsi_debug.c DIF TYPE1+TYPE3 emulation.
v2 changes:
- Select CRC_T10DIF for TARGET_CORE in Kconfig (Fengguang)
- Drop IP checksum logic from sbc_dif_v1_verify (MKP)
- Fix offset on app_tag = 0xffff in sbc_dif_verify_read()
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds sbc_check_prot() for performing various DIF
related CDB sanity checks, along with setting cmd->prot_type
once sanity checks have passed.
Also, add calls in sbc_parse_cdb() for READ_[10,12,16] +
WRITE_[10,12,16] to perform DIF sanity checking.
v2 changes:
- Make sbc_check_prot defined as static (Fengguang + Wei)
- Remove unprotected READ/WRITE warning (mkp)
- Populate cmd->prot_type + friends (Sagi)
- Drop SCF_PROT usage
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Add infrastructure for referrals.
v2 changes:
- Fix unsigned long long division in core_alua_state_lba_dependent on
32-bit (Fengguang + Chen + Hannes)
- Fix compile warning in core_alua_state_lba_dependent (nab)
- Convert segment_* + sectors variables in core_alua_state_lba_dependent
to u64 (Hannes)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Things have been quiet this round with mostly bugfixes, percpu
conversions, and other minor iscsi-target conformance testing changes.
The highlights include:
- Add demo_mode_discovery attribute for iscsi-target (Thomas)
- Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
- Add send completion interrupt coalescing for ib_isert
- Convert target-core to use percpu-refcounting for se_lun
- Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
- tcm_loop updates (Hannes)
- target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)
v3.14 is currently shaping to be a busy development cycle in target
land, with initial support for T10 Referrals and T10 DIF currently on
the roadmap"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
iscsi-target: chap auth shouldn't match username with trailing garbage
iscsi-target: fix extract_param to handle buffer length corner case
iscsi-target: Expose default_erl as TPG attribute
target_core_configfs: split up ALUA supported states
target_core_alua: Make supported states configurable
target_core_alua: Store supported ALUA states
target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
target_core_alua: spellcheck
target core: rename (ex,im)plict -> (ex,im)plicit
percpu-refcount: Add percpu-refcount.o to obj-y
iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
iscsi-target: Convert iscsi_session statistics to atomic_long_t
target: Convert se_device statistics to atomic_long_t
target: Fix delayed Task Aborted Status (TAS) handling bug
iscsi-target: Reject unsupported multi PDU text command sequence
ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
target: Core does not need blkdev.h
target: Pass through I/O topology for block backstores
iser-target: Avoid using FRMR for single dma entry requests
...
|
|
In addition to block size (already implemented), passing through
alignment offset, logical-to-phys block exponent, I/O granularity and
optimal I/O length will allow initiators to properly handle layout on
LUNs with 4K block sizes.
Tested with various weird values via scsi_debug module.
One thing to look at with this patch is the new block limits values --
instead of granularity 1 optimal 8192, Lio will now be returning whatever
the block device says, which may affect performance.
Signed-off-by: Andy Grover <agrover@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Per SBC-3, since we report ANC_SUP==0 in VPD page B2h, we need to return
an error (ILLEGAL REQUEST/INVALID FIELD IN CDB) for all WRITE SAME
requests with ANCHOR==1.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a bug for backends such as IBLOCK that perform
asynchronous completion via transport_complete_cmd(), that will call
target_complete_failure_work() -> transport_generic_request_failure(),
upon exception status and invoke cmd->transport_complete_callback()
-> compare_and_write_callback() incorrectly during the failure case.
It adds a check for a non zero se_cmd->scsi_status within the first
invocation of compare_and_write_callback(), and will jump to out plus
up se_device->caw_sem before exiting the callback.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a bug when compare_and_write_callback() invoked from
target_complete_ok_work() hits an failure from __target_execute_cmd() ->
cmd->execute_cmd(), that ends up calling transport_generic_request_failure()
-> compare_and_write_post(), thus causing SCF_COMPARE_AND_WRITE_POST to
incorrectly be set.
The result of this bug is that target_complete_ok_work() no longer hits
the if (!rc && !(cmd->se_cmd_flags & SCF_COMPARE_AND_WRITE_POST) check
that forces an immediate return, and instead double completes the se_cmd
in question, triggering an OOPs in the process.
This patch changes compare_and_write_post() to only set this bit when a
failure has not already occured to ensure the immediate return from within
target_complete_ok_work(), and thus allow transport_generic_request_failure()
to handle the sending of the CHECK_CONDITION exception status.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch resets se_cmd->data_length for COMPARE_AND_WRITE emulation
within sbc_compare_and_write() to NoLB * block_size in order to address
a bug with FILEIO backends where a I/O failure will occur when data_length
does not match the I/O size being actually dispatched for the individual
per block READs + WRITEs.
This is done late enough in sbc_compare_and_write() after the memory
allocations have occured in transport_generic_new_cmd() to not cause
any unwanted side-effects.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Update copyright ownership/year information for target-core,
loopback, iscsi-target, tcm_qla2xx, vhost and iser-target.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a extra check for SCF_COMPARE_AND_WRITE within
transport_generic_request_failure() to invoke the callback for
compare_and_write_callback() or compare_and_write_done(), in
order to release se_dev->caw_mutex from the generic failure
path.
It also adds to checks within compare_and_write_callback() to
avoid processing when transport_generic_request_failure() occurs
early enough that cmd->t_data_sg or cmd->t_bidi_data_sg have not
been setup yet, nor se_dev->caw_mutex obtained from within
sbc_compare_and_write().
v4 changes:
- Add explicit check for cmd->transport_complete_callback in
transport_generic_request_failure() to handle case where
sbc_compare_and_write()clears callback pointer (Dan Carpenter)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch changes target_complete_ok_work() to fall through
after calling the se_cmd->transport_complete_callback() ->
compare_and_write_post() callback, by keying off the existance
of SCF_COMPARE_AND_WRITE_POST.
This is necessary because once SCF_COMPARE_AND_WRITE_POST has
been set by compare_and_write_post(), the SCSI response needs
to be sent via TFO->queue_status().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
This patch adds support for COMPARE_AND_WRITE emulation on a per block
basis. This logic is used as an atomic test and set primative currently
used by VMWare ESX VAAI for performing array side locking of individual
VMFS extent ownership.
This includes the COMPARE_AND_WRITE CDB parsing within sbc_parse_cdb(),
and does the majority of the work within the compare_and_write_callback()
to perform the verify instance user data comparision, and subsequent
write instance user data I/O submission upon a successfull comparision.
The synchronization is enforced by se_device->caw_sem, that is obtained
before the initial READ I/O submission in sbc_compare_and_write(). The
mutex is then released upon MISCOMPARE in compare_and_write_callback(),
or upon WRITE instance user-data completion in compare_and_write_post().
The implementation currently assumes a single logical block (NoLB=1).
v4 changes:
- Explicitly clear cmd->transport_complete_callback for two failure
cases in sbc_compare_and_write() in order to avoid double unlock
of ->caw_sem in compare_and_write_callback() (Dan Carpenter)
v3 changes:
- Convert se_device->caw_mutex to ->caw_sem
v2 changes:
- Set SCF_COMPARE_AND_WRITE and cmd->execute_cmd() to
sbc_compare_and_write() during setup in sbc_parse_cdb()
- Use sbc_compare_and_write() for initial READ submission with
DMA_FROM_DEVICE
- Reset cmd->execute_cmd() to sbc_execute_rw() for write instance
user-data in compare_and_write_callback()
- Drop SCF_BIDI command flag usage
- Set TRANSPORT_PROCESSING + transport_state flags before write
instance submission, and convert to __target_execute_cmd()
- Prevent sbc_get_size() from being being called twice to
generate incorrect size in sbc_parse_cdb()
- Enforce se_device->caw_mutex synchronization between initial
READ I/O submission, and final WRITE I/O completion.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
COMPARE_AND_WRITE expects to be able to send down a DMA_FROM_DEVICE
to obtain the necessary READ payload for comparision against the
first half of the WRITE payload containing the verify user data.
Currently virtual backends expect to internally reference SGLs,
SGL nents, and data_direction, so change IBLOCK, FILEIO and RD
sbc_ops->execute_rw() to accept this values as function parameters.
Also add default sbc_execute_rw() handler for the typical case for
cmd->execute_rw() submission using cmd->t_data_sg, cmd->t_data_nents,
and cmd->data_direction).
v2 Changes:
- Add SCF_COMPARE_AND_WRITE command flag
- Use sbc_execute_rw() for normal cmd->execute_rw() submission
with expected se_cmd members.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
This patch adds a sense_reason_t return to ->transport_complete_callback(),
and updates target_complete_ok_work() to invoke the call if necessary to
transport_send_check_condition_and_sense() during the failure case.
Also update xdreadwrite_callback() to use this return value.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
The SBC-2 specification of READ CAPACITY(10) has PMI and LOGICAL BLOCK
ADDRESS fields in the CDB; in SBC-3 these fields are simply listed as
obsolete. However, SBC-2 also has the language
If the PMI bit is set to zero and the LOGICAL BLOCK ADDRESS field
is not set to zero, the device server shall terminate the command
with CHECK CONDITION status with the sense key set to ILLEGAL
REQUEST and the additional sense code set to INVALID FIELD IN CDB.
and in fact at least the Windows SCSI compliance test checks this
behavior. Since no one following SBC-3 is going to set these fields,
we might as well include the check from SBC-2 and pass this test.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We should use TCM_ADDRESS_OUT_OF_RANGE (-> sense data LOGICAL BLOCK
ADDRESS OUT OF RANGE) for IOs past the end of a device instead of
INVALID FIELD IN CDB.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
iblock_execute_unmap() and fd_execute_unmap share a lot of code.
Add sbc_execute_unmap() helper to remove duplicated code for
iblock_execute_unmap() and fd_execute_unmap().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Windows does not expect SYNCHRONIZE_CACHE to be not supported,
and will generate a BSOD upon shutdown when using rd_mcp backend.
So better use a noop here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Trivial, but WRITE SAME is an SBC command so it seems strange for a
related function (defined in target_core_sbc.c) to be in the spc_
namespace.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We're supposed to return LOGICAL BLOCK ADDRESS OUT OF RANGE, not
INVALID FIELD IN CDB.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a regression introduced in v3.8-rc1 code where a
zero-length READ_CAPACITY_16 was no longer returning GOOD status, but
instead returning TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE to generate
a CHECK_CONDITION status.
This regression was introduced with the following commit:
commit de103c93aff0bed0ae984274e5dc8b95899badab
Author: Christoph Hellwig <hch@lst.de>
Date: Tue Nov 6 12:24:09 2012 -0800
target: pass sense_reason as a return value
and this patch has been tested with the following zero-length CDB:
sg_raw /dev/sdd 9e 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCSI Status: Good
Sense Information:
sense buffer empty
Also, convert sbc_emulate_readcapacity() to follow the same method
of handling transport_kmap_data_sg() return values, but we never
expect a zero-length request here.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We already expect TFO->get_blocks() to return sector_t for zero value case
when doing WRITE_SAME to the end of the backend device, so go ahead and return
sector_t from spc_get_write_same_sectors() to handle this case properly.
Also, update the single iblock_execute_write_same() caller of this code.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We recently changed this to return positive subsystem error codes so the
error handling needs to be updated.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
v2: Use correct target_core_stat.c 2006 copyright year
v3: Drop extra unnessary legal verbage from header (hch)
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a new max_write_same_len device attribute for use with
WRITE_SAME w/ UNMAP=0 backend emulation. This can be useful for
lowering the default backend value (IBLOCK uses 0xFFFF).
Also, update block limits VPD emulation code in spc_emulate_evpd_b0() to
report MAXIMUM WRITE SAME LENGTH, and enforce max_write_same_len during
sbc_parse() -> sbc_setup_write_same() CDB sanity checking for all emulated
WRITE_SAME w/ UNMAP=0 cases.
(Robert: Move max_write_same_len check in sbc_setup_write_same() to
check both WRITE_SAME w/ UNMAP=1 and w/ UNMAP=0 cases)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Robert Elliott <Elliott@hp.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a new sbc_ops->execute_write_same_unmap() caller for use
with WRITE_SAME w/ UNMAP=1, and performs the ->execute_cmd() setup based
this bit within sbc_setup_write_same() code.
Also, makes the changes in sbc_parse_cdb() to handle a sense_reason_t
return from sbc_setup_write_same() on error.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
As reported by Fengguang Wu + 0 day build team, the sense_reason_t conversion
in for-next did not catch the recent sbc_emulate_noop() addition in mainline,
producing the following build warning in auto-next:
drivers/target/target_core_sbc.c: In function ‘sbc_parse_cdb’:
drivers/target/target_core_sbc.c:555: warning: assignment from incompatible pointer type
Go ahead and remove duplicate sbc_emulate_verify(), and change VERIFY to
use sbc_emulate_noop() as well.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Pass the sense reason as an explicit return value from the I/O submission
path instead of storing it in struct se_cmd and using negative return
values. This cleans up a lot of the code pathes, and with the sparse
annotations for the new sense_reason_t type allows for much better
error checking.
(nab: Convert spc_emulate_modesense + spc_emulate_modeselect to use
sense_reason_t with Roland's MODE SELECT changes)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that the reservations and ALUA code have been cleaned up there is no need
for the get_device_rev method, as we only need the standards revision in the
inquiry data, where we can hardcode it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
These really are sbc_ops, so name them correctly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Simplify the code a lot by killing the superflous struct se_subsystem_dev.
Instead se_device is allocated early on by the backend driver, which allocates
it as part of its own per-device structure, borrowing the scheme that is for
example used for inode allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
With kernel 3.6 some obsolete SCSI-2 commands including SEEK_10 have
have been removed by commit 1fd032ee10d2816c947f5d5b9abda95e728f0a8f
"target: move code for CDB emulation".
There are still clients out there which use these old SCSI-2 commands.
This mainly happens when running VMs with legacy guest systems,
connected via SCSI command pass-through to iSCSI targets. Make them
happy and return status GOOD.
Many real SCSI disks or external iSCSI storage devices still support
these old commands. So let's make LIO backward compatible as well.
This patch adds support for the previously removed SEEK_10 and
additionally the SEEK_6 and REZERO_UNIT commands.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
READ CAPACITY must be subject to the same treatment as INQUIRY,
REQUEST SENSE, and MODE SENSE, but there are no pre-existing bugs
to fix here. Just use an on-stack buffer, and copy to it after
checking the return value of transport_kmap_data_sg.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Having all the unmap payload parsing in the backed is a bit ugly, but until
more drivers support it and we can find a good interface for all of them
that seems the way to go.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Add spc_ops->execute_write_same() caller for ->execute_cmd() setup,
and update IBLOCK backends to use it.
(nab: add export of spc_get_write_same_sectors symbol)
(roland: Carry forward: Fix range calculation in WRITE SAME emulation
when num blocks == 0)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Add spc_ops->execute_sync_cache() caller for ->execute_cmd() setup,
and update IBLOCK + FILEIO backends to use it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Remove the execute_cmd method in struct se_subsystem_api, and always use the
one directly in struct se_cmd. To make life simpler for SBC virtual backends
a struct spc_ops that is passed to sbc_parse_cmd is added. For now it
only contains an execute_rw member, but more will follow with the subsequent
commits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Move the existing code in target_core_cdb.c into the files for the command
sets that the emulations implement.
(roland + nab: Squash patch: Fix range calculation in WRITE SAME emulation
when num blocks == 0s)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Instead of trying to handle all SCSI command sets in one function
(transport_generic_cmd_sequencer) call out to the backend driver to perform
this functionality. For pSCSI a copy of the existing code is used, but for
all virtual backends we can use a new parse_sbc_cdb helper is used to
provide a simple SBC emulation.
For now this setups means a fair amount of duplication between pSCSI and the
SBC library, but patches later in this series will sort out that problem.
(nab: Fix up build failure in target_core_pscsi.c)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
