Age | Commit message (Collapse) | Author |
|
It's possible that the CCK clock could run at a different rate than the
DDR clock, so use the same method to get CCK as the GMBUS code does when
calculating the new CDclk divider in the VLV display code.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On VLV/BYT, we can adjust the CDclk frequency up or down based on the
max pixel clock we need to drive. Lowering it can save power, while
raising it is necessary to support high resolution.
Add a new callback in modeset_affected_pipes and a
modeset_global_resources function to perform this adjustment as
necessary.
v2: use punit interface for 320 and 266 MHz CDclk adjustments (Ville)
v3: reset GMBUS dividers too, since we changed CDclk (Ville)
v4: jump to highest voltage when going to 400MHz CDclk (Jesse)
v5: drop duplicate define (Ville)
use shifts by 1 for fixed point (Ville)
drop new callback (Daniel)
v6: fixup adjusted_mode.clock -> adjusted_mode.crtc_clock again (Ville)
document Bunit reg access better (Ville)
v7: pass modeset_pipes and pipe_config to global_pipes so we get the right
clock data (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We don't want it delayed with the RPS work.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
For modifying self-refresh exit latency.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
With the change in the modeset sequence this shouldn't be required
any more since the ->mode_set callback now gets called when the dvo
port is fully up and running.
Also limit the retry loop to 10 tries to avoid hanging the machine
while holding important modeset locks.
Cc: Thomas Richter <thor@math.tu-berlin.de>
Tested-by: Thomas Richter <thor@math.tu-berlin.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The ns2501 controller seems to need the dpll and dvo port to accept
the timing update commands. Quick testing on my x30 here seems to
indicate that other dvo controllers don't mind. So let's move the
->mode_set callback to a place where we have the port up and running
already.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Thomas Richter <thor@math.tu-berlin.de>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a set of patches that revert all of the changes done to the
pl2303 USB serial driver in the 3.12-rc timeframe, as it turns out
they break some devices that work just fine on 3.11. As it's not a
good idea to break working systems, drop them all and they will be
reworked for future kernel versions such that there is no breakage.
I've also included a MAINTAINERS update for the USB serial subsystem
and a new device id for the ftdi_sio driver as well"
* tag 'usb-3.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: ftdi_sio: add id for Z3X Box device
USB: Maintainers change for usb serial drivers
Revert "USB: pl2303: restrict the divisor based baud rate encoding method to the "HX" chip type"
Revert "usb: pl2303: fix+improve the divsor based baud rate encoding method"
Revert "usb: pl2303: do not round to the next nearest standard baud rate for the divisor based baud rate encoding method"
Revert "usb: pl2303: remove 500000 baud from the list of standard baud rates"
Revert "usb: pl2303: move the two baud rate encoding methods to separate functions"
Revert "usb: pl2303: increase the allowed baud rate range for the divisor based encoding method"
Revert "usb: pl2303: also use the divisor based baud rate encoding method for baud rates < 115200 with HX chips"
Revert "usb: pl2303: add two comments concerning the supported baud rates with HX chips"
Revert "pl2303: simplify the else-if contruct for type_1 chips in pl2303_startup()"
Revert "pl2303: improve the chip type information output on startup"
Revert "pl2303: improve the chip type detection/distinction"
Revert "USB: pl2303: distinguish between original and cloned HX chips"
|
|
Pull clock subsystem fixes from Mike Turquette.
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: fixup argument order when setting VCO parameters
clk: socfpga: Fix incorrect sdmmc clock name
clk: armada-370: fix tclk frequencies
clk: nomadik: set all timers to use 2.4 MHz TIMCLK
|
|
Even though we only check for unclaimed registers while we're writing
registers, if we read a bad register we'll still trigger a CPU error
interrupt, and we'll print an "Unclaimed register" DRM_ERROR due to
that. To avoid this error, just avoid touching power domains that are
not enabled.
Use kzalloc so we're sure all the disabled domains will be zeroed on
the error state file. We already print the information that is enough
to discover if the power well is enabled on the error state file, so
this should not be a problem.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69747
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now that DP port CRCs are stable, we can use it for generic CRC tests.
Yay, the auto CRC source should now work everywhere!
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
They've moved the DC balance reset bit around. Again I don't think we
need it, but better safe than sorry and maybe HDMI port CRC will prove
useful for checking infoframes or hdmi audio.
v2: Apply the suggestions from Damien's review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We need to reset the DP scrambler on every vsync to get stable CRCs.
And since we can't use the normal pipe CRC on DP ports on g4x we
really need them to be able to test modesetting issues on (e)DP
outputs.
Note that the DC balance reset is for SDVO port CRCs so we don't
strictly need it. But better safe than sorry (and it's a nice template
in case we ever want to grab port CRCs for e.g. audio checking).
v2: Apply the suggestions from Damien's review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On gmch platforms the normal pipe source CRC registers don't work for
DP and TV encoders. And on newer platforms the single pipe CRC has
been replaced by a set of CRC at different stages in the platform.
Now most of our userspace tests don't care one bit about the exact
CRC, they simply want something that reflects any changes on the
screen. Hence add a new auto target for platform agnostic tests to
use.
v2: Pass back the adjusted source so that it can be shown in debugfs.
v3: I seem to be unable to get a stable CRC for DP ports. So let's
just disable them for now when using the auto mode. Note that
testcases need to be restructured so that they can dynamically skip
connectors. They also first need to set up the desired mode
configuration, since otherwise the auto mode won't do the right thing.
v4: Don't leak the modeset mutex on error paths.
v5: Spelling fix for the i9xx auto_source function.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Custom VID/PID for Z3X Box device, popular tool for cellphone flashing.
Signed-off-by: Alexey E. Kramarenko <alexeyk13@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
the "HX" chip type"
This reverts commit b8bdad608213caffa081a97d2e937e5fe08c4046.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 57ce61aad748ceaa08c859da04043ad7dae7c15e.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
the divisor based baud rate encoding method"
This reverts commit 75417d9f99f89ab241de69d7db15af5842b488c4.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit b9208c721ce736125fe58d398319513a27850fd8.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
functions"
This reverts commit e917ba01d69ad705a4cd6a6c77538f55d84f5907.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
based encoding method"
This reverts commit b5c16c6a031c52cc4b7dda6c3de46462fbc92eab.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
for baud rates < 115200 with HX chips"
This reverts commit 61fa8d694b8547894b57ea0d99d0120a58f6ebf8.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
with HX chips"
This reverts commit c23bda365dfbf56aa4d6d4a97f83136c36050e01.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pl2303_startup()"
This reverts commit 73b583af597542329e6adae44524da6f27afed62.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit a77a8c23e4db9fb1f776147eda0d85117359c700.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 034d1527adebd302115c87ef343497a889638275.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 7d26a78f62ff4fb08bc5ba740a8af4aa7ac67da4.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The last i915 drm update brought with it this annoying warning
drivers/gpu/drm/i915/intel_crt.c: In function ‘intel_crt_get_config’:
drivers/gpu/drm/i915/intel_crt.c:110:21: warning: unused variable ‘dev’ [-Wunused-variable]
struct drm_device *dev = encoder->base.dev;
^
introduced by commit 7195a50b5c7e ("drm/i915: Add HSW CRT output readout
support").
Remove the offending pointless variable.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A bit later than I would want, but the changes are very minor - a few
new device IDs for new hardware in existing drivers, fix for battery
in Wacom devices not be considered system battery and cause emergency
hibernations, and a couple of other bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ALPS - add support for model found on Dell XT2
Input: wacom - add support for ISDv4 0x10E sensor
Input: wacom - add support for ISDv4 0x10F sensor
Input: wacom - export battery scope
Input: cm109 - convert high volume dev_err() to dev_err_ratelimited()
Input: move name/timer init to input_alloc_dev()
Input: i8042 - i8042_flush fix for a full 8042 buffer
Input: pxa27x_keypad - fix NULL pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
"Last-minute ACPI and power management fixes for 3.12
- Revert epoll and select commits related to the freezer, introduced
during the 3.11 cycle, that cause mysterious user space breakage to
occur during resume from suspend to RAM for multiple users of
32-bit x86 systems. Material for 3.11.y stable kernels.
- Revert a recent ACPI-based PCI hotplug (ACPIPHP) commit that was
part of boot problem fixes for one machine, but turns out to cause
issues with hotplug on Thunderbolt chains with multiple devices.
It also turns out to be unnecessary after another fix in the same
area that went in later. From Mika Westerberg"
* tag 'pm+acpi-3.12-late' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / hotplug / PCI: Avoid doing too much for spurious notifies"
Revert "select: use freezable blocking call"
Revert "epoll: use freezable blocking call"
|
|
That explains why I was seeing 2 consecutive "Turning eDP VDD off"
messages.
Regression introduced by:
commit bf13e81b904a37d94d83dd6c3b53a147719a3ead
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Sep 6 07:40:05 2013 +0300
drm/i915: add support for per-pipe power sequencing on vlv
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
In
commit 6efdf354ddb186c6604d1692075421e8d2c740e9
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Oct 16 17:25:52 2013 +0300
the check for i915_disable_power_well flag was removed by overlook,
so add it back now.
Reported-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Incorrect definition DPIO_TX3_SWING_CTL4.
From Ville's review: "Based on the specs, the typo meant that HDMI B
ended up using "incorrect" de-emphasis for the TMDS data lanes."
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add comment from Ville's review about the impact.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now we only print messages when we actually enable VDD and when we
actually disable VDD.
The changes in the last commit triggered a big number of messages
while the driver was being initialized, and I thought we were toggling
things on/off too many times, but that was not really true: we were
just being too verbose.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If the eDP output is disabled, then we try to use /dev/i2c-X file to
do i2c transations, we get a WARN from intel_dp_check_edp() saying
we're trying to do AUX communication with the panel off. So this
commit reorganizes the code so we enable the VDD at
intel_dp_i2c_aux_ch() instead of just the callers inside i915.ko.
This fixes the i2c subtest from the pc8 test of intel-gpu-tools on
machines that have eDP panels.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch adds support for touchpad found on Dell XT2. It's a dual device
with device ID: 73, 00, 14, that comply with "ALPS_PROTO_V2".
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
into drm-fixes
Just a few small fixes for radeon (audio regression fix,
stability fix, and an endian bug noticed by coverity).
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: fix incompatible casting on big endian
drm/radeon: disable bapm on KB
drm/radeon: use sw CTS/N values for audio on DCE4+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial fixes from Greg KH:
"Here are 3 tiny fixes that are needed for 3.12-final for some serial
drivers.
One of them is a revert of a broken patch, and two others are fixes
for reported bugs. All of these have been in linux-next for a while,
I forgot I had not sent them to you yet, my fault"
(Actually, Greg, you _had_ sent two of the three, so this pulls in just
one actual new fix)
* tag 'tty-3.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/serial: at91: fix uart/usart selection for older products
|
|
Pull drm fixes from Dave Airlie:
"Mainly Intel regression fixes and quirks, along with a simple one
liner to fix rendernodes ioctl access (off by default, but testers
want to test it)"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: allow DRM_IOCTL_VERSION on render-nodes
drm/i915: Fix the PPT fdi lane bifurcate state handling on ivb
drm/i915: No LVDS hardware on Intel D410PT and D425KT
drm/i915/dp: workaround BIOS eDP bpp clamping issue
drm/i915: Add HSW CRT output readout support
drm/i915: Add support for pipe_bpp readout
|
|
The icount.reserved[] array isn't initialized so it leaks stack
information to userspace.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The DevInfo.u32Reserved[] array isn't initialized so it leaks kernel
information to user space.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to check the length parameter before doing the memcpy(). I've
actually changed it to strlcpy() as well so that it's NUL terminated.
You need CAP_NET_ADMIN to trigger these so it's not the end of the
world.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit d496f94d22d1 ('[SCSI] aacraid: fix security weakness') we
added a check on CAP_SYS_RAWIO to the ioctl. The compat ioctls need the
check as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to check "count" so we don't overflow the ei->data buffer.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 2dc4128 (ACPI / hotplug / PCI: Avoid doing too much for
spurious notifies) changed the enable_slot() to check return value of
pci_scan_slot() and if it is zero return early from the function. It
means that there were no new devices in this particular slot.
However, if a device appeared deeper in the hierarchy the code now
ignores it causing things like Thunderbolt chaining fail to recognize
new devices.
The problem with Alex Williamson's machine was solved with commit
a47d8c8 (ACPI / hotplug / PCI: Avoid parent bus rescans on spurious
device checks) and hence we should be able to restore the original
functionality that we always rescan on bus check notification.
On a device check notification we still check what acpiphp_rescan_slot()
returns and on zero bail out early.
Fixes: 2dc41281b1d1 (ACPI / hotplug / PCI: Avoid doing too much for spurious notifies)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
- Use a for_each_loop and add the corresponding #defines.
- Drop the _ILK postfix on the existing DE_PIPE_VBLANK macro for
consistency with everything else.
- Also use macros (and add the missing one for plane flips) for the
ivb display interrupt handler.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Drop the useless parens that Ville spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Request by Ville in his review of the CRC stuff. This converts
everything but ilk_display_irq_handler since that needs a bit more
than a simple search&replace to look nice.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The bbstate contains useful bits of debugging information such as
whether the batch is being read from GTT or PPGTT, or whether it is
allowed to execute privileged instructions.
v2: Only record BB_STATE for gen4+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Otherwise QA will report this as a real hang when running igt
ZZ_missed_irq.
v2: Actually test the right stuff and really shut up the DRM_ERROR
output ...
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70747
Tested-by: lu hua <huax.lu@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
DRM_IOCTL_VERSION is a reliable way to get the driver-name and version
information. It's not related to the interface-version (SET_VERSION ioctl)
so we can safely enable it on render-nodes.
Note that gbm uses udev-BUSID to load the correct mesa driver. However,
the VERSION ioctl should be the more reliable way to do this (in case we
add new DRM-bus drivers which have no BUSID or similar).
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|