aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2011-09-26xHCI: set USB2 hardware LPMAndiry Xu
If the device pass the USB2 software LPM and the host supports hardware LPM, enable hardware LPM for the device to let the host decide when to put the link into lower power state. If hardware LPM is enabled for a port and driver wants to put it into suspend, it must first disable hardware LPM, resume the port into U0, and then suspend the port. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26xHCI: test USB2 software LPMAndiry Xu
This patch tests USB2 software LPM for a USB2 LPM-capable device. When a lpm-capable device is addressed, if the host also supports software LPM, apply a test by putting the device into L1 state and resume it to see if the device can do L1 suspend/resume successfully. If the device fails to enter L1 or resume from L1 state, it may not function normally and usbcore may disconnect and re-enumerate it. In this case, store the device's Vid and Pid information, make sure the host will not test LPM for it twice. The test result is per device/host. Some devices claim to be lpm-capable, but fail to enter L1 or resume. So the test is necessary. The xHCI 1.0 errata has modified the USB2.0 LPM implementation. It redefines the HIRD field to BESL, and adds another register Port Hardware LPM Control (PORTHLPMC). However, this should not affect the LPM behavior on xHC which does not implement 1.0 errata. USB2.0 LPM errata defines a new bit BESL in the device's USB 2.0 extension descriptor. If the device reports it uses BESL, driver should use BESL instead of HIRD for it. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26xHCI: Check host USB2 LPM capabilityAndiry Xu
Check the host's USB2 LPM capability. USB2 software LPM support is optional for xHCI 0.96 hosts. xHCI 1.0 hosts should support software LPM, and may support hardware LPM. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26xHCI: Clear PLC for USB2 root hub portsAndiry Xu
When the link state changes, xHC will report a port status change event and set the PORT_PLC bit, for both USB3 and USB2 root hub ports. The PLC will be cleared by usbcore for USB3 root hub ports, but not for USB2 ports, because they do not report USB_PORT_STAT_C_LINK_STATE in wPortChange. Clear it for USB2 root hub ports in handle_port_status(). Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26xHCI: test and clear RWC bitAndiry Xu
Introduce xhci_test_and_clear_bit() to clear RWC bit in PORTSC register. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26xHCI: set link stateAndiry Xu
Introduce xhci_set_link_state() to remove redundant codes. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26usbcore: check device's LPM capabilityAndiry Xu
Check device's LPM capability by examining the bmAttibutes field of the USB2.0 Extension Descriptor. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26usbcore: get BOS descriptor setAndiry Xu
This commit gets BOS(Binary Device Object Store) descriptor set for Super Speed devices and High Speed devices which support BOS descriptor. BOS descriptor is used to report additional USB device-level capabilities that are not reported via the Device descriptor. By getting BOS descriptor set, driver can check device's device-level capability such as LPM capability. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26USB: gadget: u_serial.c: fixed a brace coding style issueShaun Silk
Signed-off-by: Shaun Silk <g0del@bigpond.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26EHCI : introduce a common ehci_setupMatthieu CASTET
This allow to clean duplicated code in most of SOC driver. Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> # fixes 3.1 build error Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26usbmon vs. tcpdump: fix dropped packet countJohannes Stezenbach
Report the number of dropped packets instead of zero when using the binary usbmon interface with tcpdump. # tcpdump -i usbmon1 -w dump tcpdump: listening on usbmon1, link-type USB_LINUX_MMAPPED (USB with padded Linux header), capture size 65535 bytes ^C2155 packets captured 2155 packets received by filter 1019 packets dropped by kernel Signed-off-by: Johannes Stezenbach <js@sig21.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26usb: gadget: udc-core: fix bug on soft_connect interfaceFelipe Balbi
We should not be using dev_get_drvdata() because we never call dev_set_drvdata(). Let's use container_of() as all other sysfs attributes. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-26USB: pl2303: add id for SMART deviceEric Benoit
Add vendor and product ID for the SMART USB to serial adapter. These were meant to be used with their SMART Board whiteboards, but can be re-purposed for other tasks. Tested and working (at at least 9600 bps). Signed-off-by: Eric Benoit <eric@ecks.ca> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-20USB: qcserial: Add support for Sierra Wireless MC8355/Gobi 3000Richard Hartmann
Simple patch to make qcserial recognize the USB id of the Sierra Wireless MC8355 which is based on the Gobi 3000 chip. Both UMTS and GPS work fine. Signed-off-by: Richard Hartmann <richih.mailinglist@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-20xhci-mem.c: xhci_segment_free: No need for checking seg argumentKautuk Consul
The seg argument to xhci_segment_free is never passed as NULL, so no need to check for this in xhci_segment_free. Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-20xhci-mem.c: Check for ring->first_seg != NULLKautuk Consul
There are 2 situations wherein the xhci_ring* might not get freed: - When xhci_ring_alloc() -> xhci_segment_alloc() returns NULL and we goto the fail: label in xhci_ring_alloc. In this case, the ring will not get kfreed. - When the num_segs argument to xhci_ring_alloc is passed as 0 and we try to free the rung after that. ( This doesn't really happen as of now in the code but we seem to be entertaining num_segs=0 in xhci_ring_alloc ) This should be backported to kernels as old as 2.6.31. Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-20USB: When hot reset for USB3 fails, try warm reset.Sarah Sharp
When a hot reset (standard USB port reset) fails on a USB 3.0 port, the host controller transitions to the "Error" state. It reports the port link state as "Inactive", sets the link state change flag, and (if the device disconnects) also reports the disconnect and connect change status. It's also supposed to transition the link state to "RxDetect", but the NEC µPD720200 xHCI host does not. Unfortunately, Harald found that the combination of the NEC µPD720200 and a LogiLink USB 3.0 to SATA adapter triggered this issue. The USB core would reset the device, the port would go into this error state, and the device would never be enumerated. This combination works under Windows, but not under Linux. When a hot reset fails on a USB 3.0 port, and the link state is reported as Inactive, fall back to a warm port reset instead. Harald confirms that with a warm port reset (along with all the change bits being correctly cleared), the USB 3.0 device will successfully enumerate. Harald also had to add two other patches ("xhci: Set change bit when warm reset change is set." and "usbcore: refine warm reset logic") to make this setup work. Since the warm reset refinement patch is not destined for the stable kernels (it's too big), this patch should not be backported either. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=41752 Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Harald Brennich <harald.brennich@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-20xhci: USB 3.0 BW checking.Sarah Sharp
The Intel Panther Point xHCI host tracks SuperSpeed endpoints in a different way than USB 2.0/1.1 endpoints. The bandwidth interval tables are not used, and instead the bandwidth is calculated in a very simple way. Bandwidth for SuperSpeed endpoints is tracked individually in each direction, since each direction has the full USB 3.0 bandwidth available. 10% of the bus bandwidth is reserved for non-periodic transfers. This checking would be more complex if we had USB 3.0 LPM enabled, because an additional latency for isochronous ping times need to be taken into account. However, we don't have USB 3.0 LPM support in Linux yet. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-20xhci: Fix mult base in endpoint bandwidth info.Sarah Sharp
The "Mult" bits in the SuperSpeed Endpoint Companion Descriptor are zero-based, and the xHCI host controller wants them to be zero-based in the input context. However, for the bandwidth math, we want them to be one-based. Fix this. Fix the documentation about the endpoint bandwidth mult variable in the xhci.h file, which says it is zero-based. Also fix the documentation about num_packets, which is also one-based, not zero-based. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-20usbcore: refine warm reset logicAndiry Xu
Current waiting time for warm(BH) reset in hub_port_warm_reset() is too short for xHC host to complete the warm reset and report a BH reset change. This patch increases the waiting time for warm reset and merges the function into hub_port_reset(), so it can handle both cold reset and warm reset, and factor out hub_port_finish_reset() to make the code looks cleaner. This fixes the issue that driver fails to clear BH reset change and port is "dead". Signed-off-by: Andiry Xu <andiry.xu@amd.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-20usb/xhci: ignore xhci version while checking for the link quirkSebastian Andrzej Siewior
instead of reading the xhci interface version each time _even_ if the quirk is not required, simply check if the quirk flag is set. This flag is only set of the module parameter is set and here is where I moved the version check to. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18USB: Realtek cr: Fix driver freeze issueedwin_rong
After auto-delink command is triggered, the CSW won't be sent back to host side, in which scenario, the USB Mass Storage driver will wait for the completion of the URB for MAX_SCHEDULE_TIMEOUT. Signed-off-by: edwin_rong <edwin_rong@realsil.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18USB: add RESET_RESUME for webcams shown to be quirkyOliver Neukum
The new runtime PM code has shown that many webcams suffer from a race condition that may crash them upon resume. Runtime PM is especially prone to show the problem because it retains power to the cameras at all times. However system suspension may also crash the devices and retain power to the devices. The only way to solve this problem without races is in usbcore with the RESET_RESUME quirk. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18Merge branch 'for-next' of git://gitorious.org/usb/usb into usb-nextGreg Kroah-Hartman
* 'for-next' of git://gitorious.org/usb/usb: (47 commits) usb: musb: Enable DMA mode1 RX for transfers without short packets usb: musb: fix build breakage usb: gadget: audio: queue wLength-sized requests usb: gadget: audio: actually support both speeds usb: gadget: storage: make FSG_NUM_BUFFERS variable size USB: gadget: storage: remove alignment assumption usb: gadget: storage: adapt logic block size to bound block devices usb: dwc3: gadget: improve debug on link state change usb: dwc3: omap: set idle and standby modes usb: dwc3: ep0: introduce ep0_expect_in flag usb: dwc3: ep0: giveback requests on stall_and_restart usb: dwc3: gadget: drop the useless dma_sync_single* calls usb: dwc3: gadget: fix GCTL programming usb: dwc3: define ScaleDown macro helper usb: dwc3: Fix definition of DWC3_GCTL_U2RSTECN usb: dwc3: gadget: do not map/unmap ZLP transfers usb: dwc3: omap: fix IRQ handling usb: dwc3: omap: change IRQ name to dwc3-omap usb: dwc3: add module.h to dwc3-omap.c and core.c usb: dwc3: omap: distinguish between SW and HW modes ...
2011-09-18USB: irq: Remove IRQF_DISABLEDYong Zhang
This flag is a NOOP and can be removed now. Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18usb: ehci: remove the 1st wmb in qh_append_tdsMing Lei
According to ehci spec 4.10.2, Advance Queue If the fetched qTD has its Active bit set to a zero, the host controller aborts the queue advance and follows the queue head's horizontal pointer to the next schedule data structure. the 'qtd' will be linked into qh hardware queue after the line below *dummy = *qtd; is executed and observed by EHCI HC, but EHCI HC won't have chance to fetch the qtd descriptor pointed by 'qtd' in qh_append_tds until the line below dummy->hw_token = token; #set Active bit here is executed by CPU and observed by EHCI HC. There is already one 'wmb' to order writing to 'dummy'/'qtd' descriptors and writing 'token' to 'dummy' descriptor(set Active bit), so the 1st wmb is not needed and can be removed. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18usb: ehci: fix comment for EHCI_SHRINK_JIFFIESMing Lei
EHCI_SHRINK_JIFFIES should be 5ms, which was just used originally, and not 200ms, so fix it. Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18usb: ehci: only prepare zero packet for out transfer if requiredMing Lei
Obviously, ZLP is only required for transfer of OUT direction, so just take same policy with UHCI for ZLP packet. Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18usb: ehci: remove wmb in qh_updateMing Lei
qh_refresh is always called when the qh is idle and has not been linked into hardware queue, so EHCI will not access overlay of the qh at this time. Just before linking qh into hardware queue, there has already one wmb to order writing qh descriptor and writing dma address of the qh into hardware queue, so HC can always see up-to-date qh descriptor once the qh is fetched with its dma address by EHCI. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18usb: cdc-acm: Owen SI-30 supportDenis Pershin
here is the patch to support Owen SI-30 device. This is a pulse counter controller. http://www.owen.ru/en/catalog/93788515 usb-drivers output: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=03eb ProdID=0030 Rev=01.01 C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=00 Driver=cdc_acm I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm This patch is installed on my home system which receives data from this controller connected to cold water counter. Signed-off-by: Denis Pershin <dyp@perchine.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18usb-storage: fix realtek cr configurationVincent Palatin
A typo in the configuration variable name prevents from activating the USB autosuspend on the device. Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18USB: g_printer: fix bug in unregistrationFabian Godehardt
The allocated chardevice region range is only 1 device but on unregister it currently tries to deregister 2. Found this while doing a insmod/rmmod/insmod/rm... of the module which seemed to eat major numbers. Signed-off-by: Fabian Godehardt <fg@emlix.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18s3c-hsudc: implement vbus_draw hookHeiko Stübner
When a transceiver is available use otg_set_power to submit the target current to it. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18usb: Provide usb_speed_string() functionMichal Nazarewicz
In a few places in the kernel, the code prints a human-readable USB device speed (eg. "high speed"). This involves a switch statement sometimes wrapped around in ({ ... }) block leading to code repetition. To mitigate this issue, this commit introduces usb_speed_string() function, which returns a human-readable name of provided speed. It also changes a few places switch was used to use this new function. This changes a bit the way the speed is printed in few instances at the same time standardising it. Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18USB: option: add various ZTE device network interfaces to the blacklistDan Williams
IDs found in the Windows driver's ZTEusbnet.inf file from the ZTE MF100 drivers (O2 UK). Also fixes the ZTE MF626 device since it really is distinct from the 4G Systems stick and apparently needs the net interface blacklisted too, while there's no indication (yet) that the 4G Systems stick does. Signed-off-by: Dan Williams <dcbw@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18USB: option: add ZTE product 0x0037 to sendsetup blacklistDan Williams
Signed-off-by: Dan Williams <dcbw@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18USB: option: convert Huawei K3765, K4505, K4605 reservered interface to ↵Dan Williams
blacklist That's what the blacklist is for... Signed-off-by: Dan Williams <dcbw@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-18USB: option: convert interface blacklisting to bitfieldsDan Williams
It's cleaner than the array stuff, and we're about to add a bunch more blacklist entries. Second, there are devices that need both the sendsetup and the reserved interface blacklists, which the current code can't accommodate. Signed-off-by: Dan Williams <dcbw@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09usb gadget: clean up FSF boilerplate textKlaus Schwarzkopf
remove the following two paragraphs as they are not needed: This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc.,59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. Signed-off-by: Klaus Schwarzkopf <schwarzkopf@sensortherm.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09musb_gadget: Fix for spurious interrupts on endpoint zero.Hans Petter Selasky
There is a multi-year old bug in the MUSB hardware which is not documented. It causes spurious interrupts and have various symptoms, like endless "SetupEnd came in a wrong ep0stage" messages. The fix is taken from the FreeBSD's musb driver. How to reproduce: For example issue clear-stall on a couple of endpoints very fast, like one request per 125us. After a while the bug triggers and the musb-chip becomes unusable until next re-enumeration. Signed-off-by: Hans Petter Selasky <hps@bitfrost.no> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09USB: for usb_autopm_get_interface_async -EINPROGRESS is not an errorJim Wylder
A return value of -EINPROGRESS from pm_runtime_get indicates that the device is already resuming due to a previous call. Internally, usb_autopm_get_interface_async doesn't treat this as an error and increments the usage count, but passes the error status along to the caller. The logical assumption of the caller is that any negative return value reflects the device not resuming and the pm_usage_cnt not being incremented. Since the usage count is being incremented and the device is resuming, return success (0) instead. Signed-off-by: James Wylder <james.wylder@motorola.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09USB: storage: Use normalized sense when emulating autosenseLuben Tuikov
This patch solves two things: 1) Enables autosense emulation code to correctly interpret descriptor format sense data, and 2) Fixes a bug whereby the autosense emulation code would overwrite descriptor format sense data with SENSE KEY HARDWARE ERROR in fixed format, to incorrectly look like this: Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] Sense Key : Recovered Error [current] [descriptor] Oct 21 14:11:07 localhost kernel: Descriptor sense data with sense descriptors (in hex): Oct 21 14:11:07 localhost kernel: 72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00 Oct 21 14:11:07 localhost kernel: 00 4f 00 c2 00 50 Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] ASC=0x4 ASCQ=0x1d Signed-off-by: Luben Tuikov <ltuikov@yahoo.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09xhci: Redundant check in xhci_check_args for xhci->devssifram.rajas@gmail.com
The xhci_hcd->devs is an array of pointers rather than pointer to pointer. Hence this check is not required. Signed-off-by: Sifram Rajas <Sifram Rajas sifram.rajas@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09xHCI: refine td allocationAndiry Xu
In xhci_urb_enqueue(), allocate a block of memory for all the TDs instead of allocating memory for each of them separately. This reduces the number of kzalloc calling when an isochronous usb is submitted. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09xhci: Don't print short isoc packets.Sarah Sharp
Now that the xHCI driver always return a status value of zero for isochronous URBs, when the last TD of an isochronous URB is short, the local variable "status" stays set to -EINPROGRESS. When xHCI driver debugging is turned on, this causes the log file to fill with messages like this: [ 38.859282] xhci_hcd 0000:00:14.0: Giveback URB ffff88013ad47800, len = 1408, expected = 580, status = -115 Don't print out the status of an URB for isochronous URBs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09xhci: Add software BW checking quirk to Intel PPT xHCISarah Sharp
The xHCI host controller in the Intel Panther Point chipset needs to have software check whether new devices will fit in the available bus bandwidth. Activate the software bandwidth checking quirk when we find the right PCI device. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09xhci: Implement HS/FS/LS bandwidth checking.Sarah Sharp
Now that we have a bandwidth interval table per root port or TT that describes the endpoint bandwidth information, we can finally use it to check whether the bus bandwidth is oversubscribed for a new device configuration/alternate interface setting. The complication for this algorithm is that the bit of hardware logic that creates the bus schedule is only 12-bit logic. In order to make sure it can represent the maximum bus bandwidth in 12 bits, it has to convert the endpoint max packet size and max esit payload into "blocks" (basically a less-precise representation). The block size for each speed of device is different, aside from low speed and full speed. In order to make sure we don't allow a setup where the scheduler might fail, we also have to do the bandwidth checking in blocks. After checking that the endpoints fit in the schedule, we store the bandwidth used for this root port or TT. If this is a FS/LS device under an external HS hub, we also update the TT bandwidth and the root port bandwidth (if this is a newly activated or deactivated TT). I won't go into the details of the algorithm, as it's pretty well documented in the comments. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09xhci: Track interval bandwidth tables per port/TT.Sarah Sharp
In order to update the root port or TT's bandwidth interval table, we will need to keep track of a list of endpoints, per interval. That way we can easily know the new largest max packet size when we have to remove an endpoint. Add an endpoint list for each root port or TT structure, sorted by endpoint max packet size. Insert new endpoints into the list such that the head of the list always has the endpoint with the greatest max packet size. Only insert endpoints and update the interval table with new information when those endpoints are periodic. Make sure to update the number of active TTs when we add or drop periodic endpoints. A TT is only considered active if it has one or more periodic endpoints attached (control and bulk are best effort, and counted in the 20% reserved on the high speed bus). If the number of active endpoints for a TT was zero, and it's now non-zero, increment the number of active TTs for the rootport. If the number of active endpoints was non-zero, and it's now zero, decrement the number of active TTs. We have to be careful when we're checking the bandwidth for a new configuration/alt setting. If we don't have enough bandwidth, we need to be able to "roll back" the bandwidth information stored in the endpoint and the root port/TT interval bandwidth table. We can't just create a copy of the interval bandwidth table, modify it, and check the bandwidth with the copy because we have lists of endpoints and entries can't be on more than one list. Instead, we copy the old endpoint bandwidth information, and use it to revert the interval table when the bandwidth check fails. We don't check the bandwidth after endpoints are dropped from the interval table when a device is reset or freed after a disconnect, because having endpoints use less bandwidth should not push the bandwidth usage over the limits. Besides which, we can't fail a device disconnect. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09xhci: Store endpoint bandwidth information.Sarah Sharp
In the upcoming patches, we'll use some stored endpoint information to make software keep track of the worst-case bandwidth schedule. We need to store several variables associated with each periodic endpoint: - the type of endpoint - Max Packet Size - Mult - Max ESIT payload - Max Burst Size (aka number of packets, stored in one-based form) - the endpoint interval (normalized to powers of 2 microframes) All this information is available to the hardware, and stored in its device output context. However, we need to ensure that the new information is stored before the xHCI driver drops the xhci->lock to wait on the Configure Endpoint command, so that another driver requesting a configuration or alt setting change will see the update. The Configure Endpoint command will never fail on the hardware that needs this software bandwidth checking (assuming the slot is enabled and the flags are set properly), so updating the endpoint info before the command completes should be fine. Until we add in the bandwidth checking code, just update the endpoint information after the Configure Endpoint command completes, and after a Reset Device command completes. Don't bother to clear the endpoint bandwidth info when a device is being freed, since the xhci_virt_ep is just going to be freed anyway. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-09-09xhci: Store information about roothubs and TTs.Sarah Sharp
For upcoming patches, we need to keep information about the bandwidth domains under the xHCI host. Each root port is a separate primary bandwidth domain, and each high speed hub's TT (and potentially each port on a multi-TT hub) is a secondary bandwidth domain. If the table were in text form, it would look a bit like this: EP Interval Sum of Number Largest Max Max Packet of Packets Packet Size Overhead 0 N mps overhead ... 15 N mps overhead Overhead is the maximum packet overhead (for bit stuffing, CRC, protocol overhead, etc) for all the endpoints in this interval. Devices with different speeds have different max packet overhead. For example, if there is a low speed and a full speed endpoint that both have an interval of 3, we would use the higher overhead (the low speed overhead). Interval 0 is a bit special, since we really just want to know the sum of the max ESIT payloads instead of the largest max packet size. That's stored in the interval0_esit_payload variable. For root ports, we also need to keep track of the number of active TTs. For each root port, and each TT under a root port, store some information about the bandwidth consumption. Dynamically allocate an array of root port bandwidth information for the number of root ports on the xHCI host. Each root port stores a list of TTs under the root port. A single TT hub only has one entry in the list, but a multi-TT hub will have an entry per port. When the USB core says that a USB device is a hub, create one or more entries in the root port TT list for the hub. When a device is deleted, and it is a hub, search through the root port TT list and delete all TT entries for the hub. Keep track of which TT entry is associated with a device under a TT. LS/FS devices attached directly to the root port will have usb_device->tt set to the roothub. Ignore that, and treat it like a primary bandwidth domain, since there isn't really a high speed bus between the roothub and the host. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 14:59:12 +0000