| Age | Commit message (Collapse) | Author |
|---|
|
To enable drivers which use SPC functions to safely exist in kernels
which are run on hardware without SPC hardware, they need a method of
detecting its presence. The new function vexpress_spc_check_loaded()
provides this.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
The TC2 core tile integrates a logic block that provides the interface
between the dual cluster test-chip and the M3 microcontroller that carries
out power management. The logic block, called SPC, contains several
memory mapped registers to control among other things low-power states,
operating points and reset control.
This patch provides a driver that enables run-time control of features
implemented by the SPC control logic.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sudeep KarkadaNagesha <Sudeep.KarkadaNagesha@arm.com>
|
|
This patch provides the new kernel infrastructure needed by versatile
express boards. Drivers are moved to drivers/misc/vexpress directory,
where Kconfig and Makefile are created. A coalesced include file is
created to cater for all versatile express required function declarations.
|
|
This static function generates a build warning as it's unused.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
CCI400 has a set of counters that can be used to profile different
transations at CCI master and slave interfaces. These counters can
observe different kinds of transations passing through the CCI and
provide a system-level view of activity.
This patch adds support for CCI PMU by extending the existing CCI
driver.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
ftrace requires any function that cannot be traced to be marked as
notrace. This patch adds notrace to disable_cci.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
|
|
Non-local variables used by the CCI management function called after
disabling the cache must be flushed out to main memory in advance,
otherwise incoherency of those values may occur if they are sitting
in the cache of some other CPU when cci_disable() executes.
This patch adds the appropriate flushing to the CCI driver to ensure
that the relevant data is available in RAM ahead of time.
Because this creates a dependency on arch-specific cacheflushing
functions, this patch also makes ARM_CCI depend on ARM.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
On ARM multi-cluster systems coherency between cores running on
different clusters is managed by the cache-coherent interconnect (CCI).
It allows broadcasting of TLB invalidates and memory barriers and it
guarantees cache coherency at system level.
This patch enables the basic infrastructure required in Linux to
handle and programme the CCI component. The first implementation is
based on a platform device, its relative DT compatible property and
a simple programming interface.
Very basic for now. More functionalities will come later.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
The amba-clcd device can be configured to use either DMA or, when this
feature is not available, an ioremapped frambuffer in static ram.
In the case of the latter, we must take care not to pass ioremapped
addresses to dma_common_mmap, since this expects only addresses from
dma_mmap_coherent, which reside in the kernel linear mapping.
This patch reworks the fb initialisation code so that either DMA or IO
implementations of the mmap/remove functions are chosen as appropriate.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch hides the dma_(alloc|free)_writecombine() calls behind macros
to allow the amba-clcd.c to be used on architectures that do not provide
this DMA API. With this patch, the *_writecombine() API is only used on
ARM (AArch32).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This check was attempting to ensure only one clcd device in the
device-tree was probed, however the check fails in the valid case where
the device is a child of another device and the 'reg' value is a offset
from the start of that other device, not an absolute address. This
occurs on vexpress with the motherboard clcd being a child of iofga.
For now, we will just have to rely on there only being one display
device specified in device-tree.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
Add support to parse the display configuration from device tree.
If the board does not provide platform specific functions in the struct
clcd_board contained with the amba device info, then defaults are provided
by the driver.
The device tree configuration can either ask for a DMA setup or provide a
framebuffer address to be remapped into the driver.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
|
|
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
This option can be used with Android to push the graphics subsystem into a
different composition strategy which is more effective when used on hardware
where the framebuffer memory is not cacheable.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
|
|
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
Reviewed-By: Liviu Dudau <liviu.dudau@arm.com>
|
|
During TC2 integration a bad config option resulted in HDLCD memory reads
not being serviced often enough. This lead to unsightly screen blanking.
These options allow the developer to count the number of underruns and
to control the color used by HDLCD when an underrun prevents accessing
pixel data. The combination of these two options allow easy diagnosis
of HDLCD underrun conditions.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
|
|
Change color byte location in 32-bit word from argb to abgr to match
the assumption made in Android when 32-bit color displays are used.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
|
|
Add a shortcut when set_par is called to only change the yoffset. Android is
doing that instead of calling pan_display to flip the framebuffer.
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
|
|
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
The ARM HDLCD device is now found in various new Versatile Express coretiles.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
The config transactions "scheduler" was hopelessly broken,
repeating completed transaction instead of picking up
next pending one.
Fixed now. Also improved debug messages.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
The registration of the "leds-gpio" device was using
"vexpress_sysreg_dev" as a parent before it was actually
set to something different than NULL.
Trivial fix by reordering the code.
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
The driver uses symbols from fbmem.c so if CONFIG_FB is not
selected we get build errors like:
drivers/built-in.o: In function `vexpress_dvi_fb_select':
:(.text+0x1b6c): undefined reference to `lock_fb_info'
:(.text+0x1ba0): undefined reference to `registered_fb'
Note, this is only a partial solution because we still have a
problem if CONFIG_FB is selected as a module.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
Versatile Express' DVI video output can be connected to one the three
sources - motherboard's CLCD controller or a video signal generated
by one of the daughterboards.
This driver configures the muxer FPGA so the output displays content
of one of the framebuffers in the system (0 by default, can be changed
by user writing to the "fb" sysfs attribute of the muxfpga device).
It will also set up the display formatter mode and keep it up
to date with mode changes requested by the user (eg. with fbset
tool).
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
The current mmc block code retries i/o errors on multi-block reads by
using single block reads. For platforms with unreliable multi-block
operations, like the ARM Versatile Express board, this is a valuable
error recovery path.
This patch extends the single block retry to also include write
operations.
Signed-off-by: Jon Medhurst <jon.medhurst@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Two driver fixes.
One avoids reading any file at a system with a cx25821 board
(fortunately, this is not a common device). The other one prevents
reading after a buffer with ISDB-T devices based on mb86a20s."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] cx25821: do not expose broken video output streams
[media] mb86a20s: Fix estimate_rate setting
|
|
variable_is_present() accesses '__efivars' directly, but when called via
gsmi_init() Michel reports observing the following crash,
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: variable_is_present+0x55/0x170
Call Trace:
register_efivars+0x106/0x370
gsmi_init+0x2ad/0x3da
do_one_initcall+0x3f/0x170
The reason for the crash is that '__efivars' hasn't been initialised nor
has it been registered with register_efivars() by the time the google
EFI SMI driver runs. The gsmi code uses its own struct efivars, and
therefore, a different variable list. Fix the above crash by passing
the registered struct efivars to variable_is_present(), so that we
traverse the correct list.
Reported-by: Michel Lespinasse <walken@google.com>
Tested-by: Michel Lespinasse <walken@google.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Matthew Garrett <matthew.garrett@nebula.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit b0de59b5733d ("TTY: do not update atime/mtime on read/write")
we removed timestamps from tty inodes to fix a security issue and waited
if something breaks. Well, 'w', the utility to find out logged users
and their inactivity time broke. It shows that users are inactive since
the time they logged in.
To revert to the old behaviour while still preventing attackers to
guess the password length, we update the timestamps in one-minute
intervals by this patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 6c7e660a27da7494c670bfba21cfeba30457656c.
The commit causes breakage on several older PXA machines.
Reported-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
I'm going to do an -rc8, so I'm just going to do this rather than delay
it any further. They are arguably stable material anyway.
* vm_ioremap_memory-examples:
mtdchar: remove no-longer-used vma helpers
vm: convert snd_pcm_lib_mmap_iomem() to vm_iomap_memory() helper
vm: convert fb_mmap to vm_iomap_memory() helper
vm: convert mtdchar mmap to vm_iomap_memory() helper
vm: convert HPET mmap to vm_iomap_memory() helper
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Three groups of fixes:
1. Make sure we don't execute the early microcode patching if family
< 6, since it would touch MSRs which don't exist on those
families, causing crashes.
2. The Xen partial emulation of HyperV can be dealt with more
gracefully than just disabling the driver.
3. More EFI variable space magic. In particular, variables hidden
from runtime code need to be taken into account too."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode: Verify the family before dispatching microcode patching
x86, hyperv: Handle Xen emulation of Hyper-V more gracefully
x86,efi: Implement efi_no_storage_paranoia parameter
efi: Export efi_query_variable_store() for efivars.ko
x86/Kconfig: Make EFI select UCS2_STRING
efi: Distinguish between "remaining space" and actually used space
efi: Pass boot services variable info to runtime code
Move utf16 functions to kernel core and rename
x86,efi: Check max_size only if it is non-zero.
x86, efivars: firmware bug workarounds should be in platform code
|
|
Pull sparc fixes from David Miller:
1) Fix race in sparc64 TLB shootdowns, we have to synchronize with the
sibling cpus completing if we are passing them a reference via
pointer to a data structure.
2) Fix cleaning of bitmaps in sparc32, from Akinobu Mita.
3) Fix various sparc header mistakes, some of which resulted in
userland build breakage. From Sam Ravnborg.
4) Kill ghost declarations and defines missed when several bits of code
got deleted recently.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix race in TLB batch processing.
sparc: use asm-generic version of types.h
bbc_i2c: fix section mismatch warning
sparc: use generic headers
sparc:cleanup unused code in smp_32.h
sparc/iommu: fix typo s/265KB/256KB/
sparc/srmmu: clear trailing edge of bitmap properly
sparc:remove unused declaration smp_boot_cpus()
|
|
Pull networking updates from David Miller:
1) ax88796 does 64-bit divides which causes link errors on ARM, fix
from Arnd Bergmann.
2) Once an improper offload setting is detected on an SKB we don't rate
limit the log message so we can very easily live lock. From Ben
Greear.
3) Openvswitch cannot report vport configuration changes reliably
because it didn't preallocate the netlink notification message
before changing state. From Jesse Gross.
4) The effective UID/GID SCM credentials fix, from Linus.
5) When a user explicitly asks for wireless authentication, cfg80211
isn't told about the AP detachment leaving inconsistent state. Fix
from Johannes Berg.
6) Fix self-MAC checks in batman-adv on multi-mesh nodes, from Antonio
Quartulli.
7) Revert build_skb() change sin IGB driver, can result in memory
corruption. From Alexander Duyck.
8) Fix setting VLANs on virtual functions in IXGBE, from Greg Rose.
9) Fix TSO races in qlcnic driver, from Sritej Velaga.
10) In bnx2x the kernel driver and UNDI firmware can try to program the
chip at the same time, resulting in corruption. Add proper
synchronization. From Dmitry Kravkov.
11) Fix corruption of status block in firmware ram in bxn2x, from Ariel
Elior.
12) Fix load balancing hash regression of bonding driver in forwarding
configurations, from Eric Dumazet.
13) Fix TS ECR regression in TCP by calling tcp_replace_ts_recent() in
all the right spots, from Eric Dumazet.
14) Fix several bonding bugs having to do with address manintainence,
including not removing address when configuration operations
encounter errors, missed locking on the address lists, missing
refcounting on VLAN objects, etc. All from Nikolay Aleksandrov.
15) Add workarounds for firmware bugs in LTE qmi_wwan devices, wherein
the devices fail to add a proper ethernet header while on LTE
networks but otherwise properly do so on 2G and 3G ones. From Bjørn
Mork.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: fix incorrect credentials passing
net: rate-limit warn-bad-offload splats.
net: ax88796: avoid 64 bit arithmetic
qlge: Update version to 1.00.00.32.
qlge: Fix ethtool autoneg advertising.
qlge: Fix receive path to drop error frames
net: qmi_wwan: prevent duplicate mac address on link (firmware bug workaround)
net: qmi_wwan: fixup destination address (firmware bug workaround)
net: qmi_wwan: fixup missing ethernet header (firmware bug workaround)
bonding: in bond_mc_swap() bond's mc addr list is walked without lock
bonding: disable netpoll on enslave failure
bonding: primary_slave & curr_active_slave are not cleaned on enslave failure
bonding: vlans don't get deleted on enslave failure
bonding: mc addresses don't get deleted on enslave failure
pkt_sched: fix error return code in fw_change_attrs()
irda: small read past the end of array in debug code
tcp: call tcp_replace_ts_recent() from tcp_ack()
netfilter: xt_rpfilter: skip locally generated broadcast/multicast, too
netfilter: ipset: bitmap:ip,mac: fix listing with timeout
bonding: fix l23 and l34 load balancing in forwarding path
...
|
|
Matt Fleming (1):
x86, efivars: firmware bug workarounds should be in platform
code
Matthew Garrett (3):
Move utf16 functions to kernel core and rename
efi: Pass boot services variable info to runtime code
efi: Distinguish between "remaining space" and actually used
space
Richard Weinberger (2):
x86,efi: Check max_size only if it is non-zero.
x86,efi: Implement efi_no_storage_paranoia parameter
Sergey Vlasov (2):
x86/Kconfig: Make EFI select UCS2_STRING
efi: Export efi_query_variable_store() for efivars.ko
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
When building ax88796 on an ARM platform with 64-bit resource_size_t,
we currently get
drivers/net/ethernet/8390/ax88796.c:875: undefined reference to `__aeabi_uldivmod'
because we do a division on the length of the MMIO resource.
Since we know that this resource is very short, using an
"unsigned long" instead of "resource_size_t" is entirely
sufficient, and avoids this link-time error.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Autoneg is supported on specific port types only. Fix the driver to advertise
autoneg based on the port type.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Fix the driver to drop error frames in the receive path
o Update error counter which was not getting incremented
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We normally trust and use the CDC functional descriptors provided by a
number of devices. But some of these will erroneously list the address
reserved for the device end of the link. Attempting to use this on
both the device and host side will naturally not work.
Work around this bug by ignoring the functional descriptor and assign a
random address instead in this case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Received packets are sometimes addressed to 00:a0:c6:00:00:00
instead of the address the device firmware should have learned
from the host:
321.224126 77.16.85.204 -> 148.122.171.134 ICMP 98 Echo (ping) request id=0x4025, seq=64/16384, ttl=64
0000 82 c0 82 c9 f1 67 82 c0 82 c9 f1 67 08 00 45 00 .....g.....g..E.
0010 00 54 00 00 40 00 40 01 57 cc 4d 10 55 cc 94 7a .T..@.@.W.M.U..z
0020 ab 86 08 00 62 fc 40 25 00 40 b2 bc 6e 51 00 00 ....b.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
321.240607 148.122.171.134 -> 77.16.85.204 ICMP 98 Echo (ping) reply id=0x4025, seq=64/16384, ttl=55
0000 00 a0 c6 00 00 00 02 50 f3 00 00 00 08 00 45 00 .......P......E.
0010 00 54 00 56 00 00 37 01 a0 76 94 7a ab 86 4d 10 .T.V..7..v.z..M.
0020 55 cc 00 00 6a fc 40 25 00 40 b2 bc 6e 51 00 00 U...j.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
The bogus address is always the same, and matches the address
suggested by many devices as a default address. It is likely a
hardcoded firmware default.
The circumstances where this bug has been observed indicates that
the trigger is related to timing or some other factor the host
cannot control. Repeating the exact same configuration sequence
that caused it to trigger once, will not necessarily cause it to
trigger the next time. Reproducing the bug is therefore difficult.
This opens up a possibility that the bug is more common than we can
confirm, because affected devices often will work properly again
after a reset. A procedure most users are likely to try out before
reporting a bug.
Unconditionally rewriting the destination address if the first digit
of the received packet is 0, is considered an acceptable compromise
since we already have to inspect this digit. The simplification will
cause unnecessary rewrites if the real address starts with 0, but this
is still better than adding additional tests for this particular case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of LTE devices from different vendors all suffer from the
same firmware bug: Most of the packets received from the device while
it is attached to a LTE network will not have an ethernet header. The
devices work as expected when attached to 2G or 3G networks, sending
an ethernet header with all packets.
This driver is not aware of which network the modem attached to, and
even if it were there are still some packet types which are always
received with the header intact.
All devices supported by this driver have severely limited
networking capabilities:
- can only transmit IPv4, IPv6 and possibly ARP
- can only support a single host hardware address at any time
- will only do point-to-point communcation with the host
Because of this, we are able to reliably identify any bogus raw IP
packets by simply looking at the 4 IP version bits. All we need to
do is to avoid 4 or 6 in the first digit of the mac address. This
workaround ensures this, and fix up the received packets as necessary.
Given the distribution of the bug, it is believed that the source is
the chipset vendor. The devices which are verified to be affected are:
Huawei E392u-12 (Qualcomm MDM9200)
Pantech UML290 (Qualcomm MDM9600)
Novatel USB551L (Qualcomm MDM9600)
Novatel E362 (Qualcomm MDM9600)
It is believed that the bug depend on firmware revision, which means
that possibly all devices based on the above mentioned chipset may be
affected if we consider all available firmware revisions.
The information about affected devices and versions is likely
incomplete. As the additional overhead for packets not needing this
fixup is very small, it is considered acceptable to apply the
workaround to all devices handled by this driver.
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netif_addr_lock_bh() to acquire the appropriate lock before walking.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
slave_disable_netpoll() is not called upon enslave failure which would
lead to a memory leak. Call slave_disable_netpoll() after err_detach as
that's the first error path after enabling netpoll on that slave.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On enslave failure primary_slave can point to new_slave which is to be
freed, and the same applies to curr_active_slave. So check if this is
the case and clean up properly after err_detach because that's the first
error code path after they're set.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The main problem is with vid refcount which only gets bumped up.
Delete the vlans after err_detach as that's the first error path
after the vlans are added.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add bond_mc_list_flush() after err_detach as that's the first error path
after the addresses are added. The main issue is the mc addresses' refcount
which only gets bumped up.
v2: update log message and don't move code unnecessarily
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
A few stragglers hoping for 3.9, somewhat delayed due to my travels...
On the mac80211 bits, Johannes says:
"Sadly, I have another pull request -- the idle handling fix broke LED
handling in some cases."
and:
"Yet one more!
This fixes a fairly important/annoying bug -- when roaming between
multiple APs of the same network, the system could get stuck thinking it
was connected to the old one while it really wasn't."
On top of that...
Arend sends a brcmfmac patch that removes advertising a feature that
isn't actually fully supported, and a brcmsmac patch that rearranges
code to request firmware at IFF_UP to play more nicely with being
built into the kernel.
Felix gives us a minor ath9k_htc fix to support the newly released
open source firmware, and an ath9k_hw initvals fix to improve device
stability.
Rafał Miłecki provides a fix for an ssb regression that caused a
serious performance problem with b43.
Zefir Kurtisi offers an ath9k fix to change some kmalloc flags to
allow the DFS detector to be called in softirq context.
Please let me know if there are problems. If these don't make 3.9,
I'll just pull them into wireless-next -- just let me know if you
want to do it that way!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the conversion to vm_iomap_memory(), these vma helpers are no
longer used.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
