aboutsummaryrefslogtreecommitdiff
path: root/net/mac80211/debugfs_netdev.c
AgeCommit message (Collapse)Author
2013-02-04mac80211: mesh power save basicsMarco Porsch
Add routines to - maintain a PS mode for each peer and a non-peer PS mode - indicate own PS mode in transmitted frames - track neighbor STAs power modes - buffer frames when neighbors are in PS mode - add TIM and Awake Window IE to beacons - release frames in Mesh Peer Service Periods Add local_pm to sta_info to represent the link-specific power mode at this station towards the remote station. When a peer link is established, use the default power mode stored in mesh config. Update the PS status if the peering status of a neighbor changes. Maintain a mesh power mode for non-peer mesh STAs. Set the non-peer power mode to active mode during peering. Authenticated mesh peering is currently not working when either node is configured to be in power save mode. Indicate the current power mode in transmitted frames. Use QoS Nulls to indicate mesh power mode transitions. For performance reasons, calls to the function setting the frame flags are placed in HWMP routing routines, as there the STA pointer is already available. Add peer_pm to sta_info to represent the peer's link-specific power mode towards the local station. Add nonpeer_pm to represent the peer's power mode towards all non-peer stations. Track power modes based on received frames. Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS neighbor counter and group-addressed frame buffer). Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame buffering routines in the tx path. Update num_sta_ps to buffer and release group-addressed frames after DTIM beacons. Announce the awake window duration in beacons if in light or deep sleep mode towards any peer or non-peer. Create a TIM IE similarly to AP mode and add it to mesh beacons. Parse received Awake Window IEs and check TIM IEs for buffered frames. Release frames towards peers in mesh Peer Service Periods. Use the corresponding trigger frames and monitor the MPSP status. Append a QoS Null as trigger frame if neccessary to properly end the MPSP. Currently, in HT channels MPSPs behave imperfectly and show large delay spikes and frame losses. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26mac80211: convert to channel definition structJohannes Berg
Convert mac80211 (and where necessary, some drivers a little bit) to the new channel definition struct. This will allow extending mac80211 for VHT, which is currently restricted to channel contexts since there are no drivers using that which makes it easier. As I also don't care about VHT for drivers not using the channel context API, I won't convert the previous API to VHT support. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-09mac80211: add debugfs file for HW queuesJohannes Berg
Add a debugfs file showing which HW queues were allocated to a virtual interface, including the CAB queue for AP interfaces. Change-Id: I486924e961b6ad6785a79db09620919ee644e703 Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-07mac80211: use kstrtoull return valueJohannes Berg
If kstrtoull() returns an error code (a value smaller than zero), use it since it can be an error other than -EINVAL. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-07mac80211: fix race in TKIP MIC test debugfs fileJohannes Berg
Accessing sdata->vif.bss_conf.bssid without any protection here is racy, use u.mgd.associated instead and lock the correct mutex for it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-07mac80211: use mac_ptonJohannes Berg
Instead of implementing practically the same function (hwaddr_aton) use mac_pton. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30mac80211: handle TX power per virtual interfaceJohannes Berg
Even before channel contexts/multi-channel, having a single global TX power limit was already problematic, in particular if two managed interfaces connected to two APs with different power constraints. The channel context introduction completely broke this though and in fact I had disabled TX power configuration there for drivers using channel contexts. Change everything to track TX power per interface so that different user settings and different channel maxima are treated correctly. Also continue tracking the global TX power though for compatibility with applications that attempt to configure the wiphy's TX power globally. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-19mac80211: make client powersave independent of interface typeMarco Porsch
This patch prepares mac80211 for a later implementation of mesh or ad-hoc powersave clients. The structures related to powersave (buffer, TIM map, counters) are moved from the AP-specific interface structure to a generic structure that can be embedded into any interface type. The functions related to powersave are prepared to allow easy extension with different interface types. For example with: + } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) { + ps = &sdata->u.mesh.ps; Some references to the AP's beacon structure are removed where they were obviously not used. The patch compiles without warning and has been briefly tested as AP interface with one client in PS mode. Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-17mac80211: move out the non-statistics variable estab_plinks from mesh_statAshok Nagarajan
estab_plinks is not a statistics member. Hence move estab_plinks from struct mesh_stat to struct ieee80211_if_mesh Signed-off-by: Ashok Nagarajan <ashok@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-17mac80211: track needed RX chains for channel contextsJohannes Berg
On each channel that the device is operating on, it may need to listen using one or more chains depending on the SMPS settings of the interfaces using it. The previous channel context changes completely removed this ability (before, it was available as the SMPS mode). Add per-context tracking of the required static and dynamic RX chains and notify the driver on changes. To achieve this, track the chains and SMPS mode used on each virtual interface and update the channel context whenever this changes. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-24mac80211: clean up debuggingJohannes Berg
There are a few things that make the logging and debugging in mac80211 less useful than it should be right now: * a lot of messages should be pr_info, not pr_debug * wholesale use of pr_debug makes it require *both* Kconfig and dynamic configuration * there are still a lot of ifdefs * the style is very inconsistent, sometimes the sdata->name is printed in front Clean up everything, introducing new macros and separating out the station MLME debugging into a new Kconfig symbol. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-18{nl,cfg,mac}80211: implement dot11MeshHWMPconfirmationIntervalChun-Yeow Yeoh
As defined in section 13.10.9.3 Case D (802.11-2012), this control variable is used to limit the mesh STA to send only one PREQ to a root mesh STA within this interval of time (in TUs). The default value for this variable is set to 2000 TUs. However, for current implementation, the maximum configurable of dot11MeshHWMPconfirmationInterval is restricted by dot11MeshHWMPactivePathTimeout. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> [line-break commit log] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-14{nl,cfg,mac}80211: implement dot11MeshHWMProotInterval and ↵Chun-Yeow Yeoh
dot11MeshHWMPactivePathToRootTimeout Add the mesh configuration parameters dot11MeshHWMProotInterval and dot11MeshHWMPactivePathToRootTimeout to be used by proactive PREQ mechanism. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> [line-break commit log] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-11{nl,cfg,mac}80211: fix the coding style related to mesh parametersChun-Yeow Yeoh
fix the coding style related to mesh parameters, especially the indentation, as pointed out by Johannes Berg. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-06mac80211: Add missing mesh parameter dot11MeshForwarding for debugfsChun-Yeow Yeoh
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05net: mac80211: Convert printk(KERN_DEBUG to pr_debugJoe Perches
Standardize the debugging to be able to use dynamic_debug. Coalesce formats, align arguments. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-16mac80211: Add debugfs entry for mesh ht_opmodeAshok Nagarajan
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-24mac80211: rename AP variable num_sta_authorized to num_mcast_staFelix Fietkau
It is only used to test for BSS multicast receivers. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-12Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
2012-04-10mac80211: Allow tsf increments via debugfsJavier Cardona
Reading and writing back the tsf value via tsf is too slow if one wants to make small increments to this timer. With this change you can use the syntax "+=<some value>" or "-=<some value>" to add or substract a value from the tsf counter. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-09mac80211: reduce code duplication in debugfs codeFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-05simple_open: automatically convert to simple_open()Stephen Boyd
Many users of debugfs copy the implementation of default_open() when they want to support a custom read/write function op. This leads to a proliferation of the default_open() implementation across the entire tree. Now that the common implementation has been consolidated into libfs we can replace all the users of this function with simple_open(). This replacement was done with the following semantic patch: <smpl> @ open @ identifier open_f != simple_open; identifier i, f; @@ -int open_f(struct inode *i, struct file *f) -{ ( -if (i->i_private) -f->private_data = i->i_private; | -f->private_data = i->i_private; ) -return 0; -} @ has_open depends on open @ identifier fops; identifier open.open_f; @@ struct file_operations fops = { ... -.open = open_f, +.open = simple_open, ... }; </smpl> [akpm@linux-foundation.org: checkpatch fixes] Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-03-15mac80211: make uapsd_* keys per-vifEliad Peller
uapsd_queues and uapsd_max_sp_len are relevant only for managed interfaces, and can be configured differently for each vif. Move them from the local struct to sdata->u.mgd, and update the debugfs functions accordingly. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15mac80211: add NULL terminator to debugfs_netdev write bufEliad Peller
Some debugfs write functions call kstrto* functions, which assume the string is null-terminated. Make it valid by changing ieee80211_if_write() to use static buffer instead of allocating one, and set the last char to NULL. (The write functions try to parse some integer/mac address, so 64 bytes buffer should be enough) Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06mac80211: Modify tsf via debugfs in mesh interfacesJavier Cardona
Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05{nl,cfg,mac}80211: Implement RSSI threshold for mesh peeringAshok Nagarajan
Mesh peer links are established only if average rssi of the peer candidate satisfies the threshold. This is not in 802.11s specification but was requested by David Fulgham, an open80211s user. This is a way to avoid marginal peer links with stations that are barely within range. This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This feature is supported only for hardwares that report signal in dBm. Signed-off-by: Ashok Nagarajan <ashok@cozybit.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-30mac80211: add support for mcs masksSimon Wunderlich
* Handle MCS masks set by the user. * Match rates provided by the rate control algorithm to the mask set, also in HT mode, and switch back to legacy mode if necessary. * add debugfs files to observate the rate selection Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-27{nl,cfg,mac}80211: Add support of setting non-forwarding entity in MeshChun-Yeow Yeoh
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the mesh node can prevent itself from forwarding the traffic which is not destined to him. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-12-15mac80211: count authorized stations per BSSJohannes Berg
Currently, each AP interface will send multicast traffic if any interface has a station entry even if that station entry is allocated only. With the new station state management we can easily fix it by adding a counter that counts each authorized station only and send multicast traffic only when the correct interface has at least one authorized station. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-28{nl,cfg,mac}80211: implement dot11MeshHWMPperrMinIntervalThomas Pedersen
As per 802.11mb 13.9.11.3 Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27mac80211: add ieee80211_vif param to tsf functionsEliad Peller
TSF can be kept per vif. Add ieee80211_vif param to set/get/reset_tsf, and move the debugfs entries to the per-vif directory. Update all the drivers that implement these callbacks. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14mac80211: Stop forwarding mesh traffic when tx queues are fullJavier Cardona
Tx flow control for non-mesh modes of operation only needs to act on the net device queues: when the hardware queues are full we stop accepting traffic from the net device. In mesh, however, we also need to stop forwarding traffic. This patch checks the hardware queues before attempting to forward a mesh frame. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24{nl,cfg,mac}80211: let userspace make meshif mesh gateJavier Cardona
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute, which will advertise this mesh node as being a mesh gate. NL80211_HWMP_ROOTMODE must be set or this will do nothing. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24{nl,cfg,mac}80211: let userspace set RANN intervalJavier Cardona
Allow userspace to set Root Announcement Interval for our mesh interface. Also, RANN interval is now in proper units of TUs. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24{nl,mac}80211: add missing root mode meshconf entriesJavier Cardona
This fix allows userspace to mark a meshif as a root node. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-20mac80211: fix SMPS debugfs lockingJohannes Berg
The locking with SMPS requests means that the debugs file should lock the mgd mutex, not the iflist mutex. Calls to __ieee80211_request_smps() need to hold that mutex, so add an assertion. This has always been wrong, but for some reason never been noticed, probably because the locking error only happens while unassociated. Cc: stable@kernel.org [2.6.34+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03mac80211: Add testing functionality for TKIPJouni Malinen
TKIP countermeasures depend on devices being able to detect Michael MIC failures on received frames and for stations to report errors to the AP. In order to test that behavior, it is useful to be able to send out TKIP frames with incorrect Michael MIC. This testing behavior has minimal effect on the TX path, so it can be added to mac80211 for convenient use. The interface for using this functionality is a file in mac80211 netdev debugfs (tkip_mic_test). Writing a MAC address to the file makes mac80211 generate a dummy data frame that will be sent out using invalid Michael MIC value. In AP mode, the address needs to be for one of the associated stations or ff:ff:ff:ff:ff:ff to use a broadcast frame. In station mode, the address can be anything, e.g., the current BSSID. It should be noted that this functionality works correctly only when associated and using TKIP. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03mac80211: Show configured channel-type in netdev debugfs.Ben Greear
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28mac80211: Add sdata state and flags to debugfs.Ben Greear
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06nl80211/mac80211: define and allow configuring mesh element TTLJavier Cardona
The TTL in path selection information elements is different from the mesh ttl used in mesh data frames. Version 7.03 of the 11s draft calls this ttl 'Element TTL'. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits) bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL. vlan: Calling vlan_hwaccel_do_receive() is always valid. tproxy: use the interface primary IP address as a default value for --on-ip tproxy: added IPv6 support to the socket match cxgb3: function namespace cleanup tproxy: added IPv6 support to the TPROXY target tproxy: added IPv6 socket lookup function to nf_tproxy_core be2net: Changes to use only priority codes allowed by f/w tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled tproxy: added tproxy sockopt interface in the IPV6 layer tproxy: added udp6_lib_lookup function tproxy: added const specifiers to udp lookup functions tproxy: split off ipv6 defragmentation to a separate module l2tp: small cleanup nf_nat: restrict ICMP translation for embedded header can: mcp251x: fix generation of error frames can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set can-raw: add msg_flags to distinguish local traffic 9p: client code cleanup rds: make local functions/variables static ... Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and drivers/net/wireless/ath/ath9k/debug.c as per David
2010-09-27mac80211: Support multiple VIFS per AP in debugfs.Ben Greear
Create 'stations' sub-directory under each netdev:[vif-name] directory to hold all stations for that network device. Signed-off-by: Ben Greear <greearb@candelatech.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-16net/wireless: use generic_file_llseek in debugfsArnd Bergmann
The default llseek operation is changing from default_llseek to no_llseek, so all code relying on the current behaviour needs to make that explicit. The wireless driver infrastructure and some of the drivers make use of generated debugfs files, so they cannot be converted by our script that automatically determines the right operation. All these files use debugfs and they typically rely on simple_read_from_buffer, so the best llseek operation here is generic_file_llseek. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org
2010-04-15Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: Documentation/feature-removal-schedule.txt drivers/net/wireless/ath/ath5k/phy.c drivers/net/wireless/wl12xx/wl1271_main.c
2010-04-08Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into merge Conflicts: Documentation/feature-removal-schedule.txt drivers/net/wireless/ath/ath5k/phy.c drivers/net/wireless/iwlwifi/iwl-4965.c drivers/net/wireless/iwlwifi/iwl-agn.c drivers/net/wireless/iwlwifi/iwl-core.c drivers/net/wireless/iwlwifi/iwl-core.h drivers/net/wireless/iwlwifi/iwl-tx.c
2010-03-31mac80211: Track Beacon signal strength and implement cqm eventsJouni Malinen
Calculate a running average of the signal strength reported for Beacon frames and indicate cqm events if the average value moves below or above the configured threshold value (and filter out repetitive events with by using the configured hysteresis). Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-03-30include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo
implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-10mac80211: Fix memory leak in ieee80211_if_write()Eric Dumazet
Fix memory leak and use kmalloc() instead of kzalloc() as we are going to overwrite the allocated buffer. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-12mac80211: remove unused type argumentJohannes Berg
The type argument to DEBUGFS_ADD() isn't used and can be removed, it's around from before the conversion to debugfs_remove_recursive(). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-12cfg80211/mac80211: Use more generic bitrate mask for rate controlJouni Malinen
Extend struct cfg80211_bitrate_mask to actually use a bitfield mask instead of just a single fixed or maximum rate index. This change itself does not modify the behavior (except for debugfs files), but it prepares cfg80211 and mac80211 for a new nl80211 command for setting which rates can be used in TX rate control. Since frames are now going through the rate control algorithm unconditionally, the internal IEEE80211_TX_INTFL_RCALGO flag can now be removed. The RC implementations can use the rate_idx_mask value to optimize their behavior if only a single rate is enabled. The old max_rate_idx in struct ieee80211_tx_rate_control is maintained (but commented as deprecated) for backwards compatibility with existing RC implementations. Once these implementations have been updated to use the more generic rate_idx_mask, the max_rate_idx value can be removed. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-31 18:11:05 +0000