aboutsummaryrefslogtreecommitdiff
path: root/sound/soc/codecs/twl4030.c
AgeCommit message (Collapse)Author
2013-01-11ASoC: twl4030: Remove suspend/resume soc driver operationsPeter Ujfalusi
With idle_bias_off these are no longer needed. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-02ASoC: twl4030: Configure extmute pinmux when the dedicated pin is in usePeter Ujfalusi
When HS extmute is enabled without custom GPIO we should configure the mux to allow the pin to be used as extmute signal. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-02ASoC: twl4030: Convert MICBIAS to SUPPLY widgetPeter Ujfalusi
In order to avoid breakage update the machine drivers at the same time using twl4030: omap3pandora, sdp3430 and zoom2 Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-02ASoC: twl4030: Correct the support for Voice portPeter Ujfalusi
In order to be able to use the Voice port of twl4030 three bits need to be handled in VOICE_IF register: VIF_EN: to enable the voice port (needed for both playback and capture) VIF_DIN_EN: Need to be enabled for playback only (input to the codec) VIF_DOUT_EN: Need to be enabled for capture only (output from codec) Use DAPM_SUPPLY for the VIF_EN bit and add DAPM_AIF_IO/OUT widget to handle the playback/capture bit. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-12-10ASoC: twl4030: remove __dev* attributesBill Pemberton
CONFIG_HOTPLUG is going away as an option. As result the __dev* markings will be going away. Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst, and __devexit. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl4030: Support for DT booted kernelPeter Ujfalusi
When the kernel has been booted with DT blob the platform data is NULL for the driver. We need to construct the pdata based on the DT information for runtime use. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl4030: Add pointer to pdata within the private dataPeter Ujfalusi
Access the pdata via a pointer within the twl4030_priv structure. In preparation for DeviceTree support. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl4030: Convert to use devm_kzallocPeter Ujfalusi
Allocate the private data with devm_kzalloc. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC/mfd: twl4030: Remove set_hs_extmute callback from platform dataPeter Ujfalusi
We no longer have users for the set_hs_extmute callback which has been replaced by hs_extmute_gpio so the codec driver can handle the external mute if it is needed by the board. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl4030: Move hs_extmute GPIO handling to driverPeter Ujfalusi
The external mute (if it is in use) is handled by a GPIO line. Prepare to remove the set_hs_extmute callback and replace it with: hs_extmute_gpio: the GPIO number to use for external mute When the users of set_hs_extmute has been converted the callback can be removed. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl4030: Convert to use DAI DAPM widgetsPeter Ujfalusi
Use DAPM mapping for stream events and give unique names for the streams. This change also fixes the following warning: twl4030-codec twl4030-codec: Failed to create Capture debugfs file Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-18ASoC: Avoid recalculating the bitmask for SOC_ENUM controlsLars-Peter Clausen
For ENUM controls the bitmask is calculated based on the number of items. Currently this is done each time the control is accessed. And while the performance impact of this should be negligible we can easily do better. The roundup_pow_of_two macro performs the same calculation which is currently done manually, but it is also possible to use this macro with compile time constants and so it can be used to initialize static data. So we can use it to initialize the mask field of a ENUM control during its declaration. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-04ASoC: codecs: Remove rtd->codec usage from CODEC driversMark Brown
In order to support CODEC<->CODEC links remove the assumption that there is only a single CODEC on a DAI link by removing the use of the CODEC pointer in the rtd from the CODEC drivers. They are already being passed their DAI whenever they are passed an rtd and can get the CODEC from there. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-02-21ASoC: twl4030: Debug code cleanupPeter Ujfalusi
Replace the printk(KERN_ERR* instances with dev_err in the driver. While we are here clean up some of the debug messages as well. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-02-09ASoC: Fix typo in twl4030.cMasanari Iida
Correct spelling "memroy" to "memory" in sound/soc/codecs/twl4030.c Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-27ASoC: Set idle_bias_off flag in snd_soc_codec_driverAxel Lin
Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver for devices can unconditionally support idle_bias_off. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-20ASoC: twl4030: Use core to set the msbits constraintPeter Ujfalusi
Core can set the msbits constraint in behalf of the dai. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-02ASoC: Drop unused state parameter from CODEC suspend callbackLars-Peter Clausen
The existence of this parameter is purely historical. None of the CODEC drivers uses it and we always pass in the same value anyway, so it should be safe to remove it. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-28ASoC: Convert CODEC drivers to module_platform_driverMark Brown
Factors out a bit of boilerplate. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23ASoC: Constify snd_soc_dai_ops structsLars-Peter Clausen
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure") introduced the possibility to have constant DAI ops structures, yet this is barley used in both existing drivers and also new drivers being submitted, although none of them modifies its DAI ops structure. The later is not surprising since existing drivers are often used as templates for new drivers. So this patch just constifies all existing snd_soc_dai_ops structs to eliminate the issue altogether. The patch was generated with the following coccinelle semantic patch: // <smpl> @@ identifier ops; @@ -struct snd_soc_dai_ops ops = +const struct snd_soc_dai_ops ops = { ... }; // </smpl> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-11ASoC: twl4030: Convert to table based initPeter Ujfalusi
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05ASoC: Consolidate use of controls with custom get/put functionPeter Ujfalusi
Use the macros for controls require custom get/put function. This is to make sure that the soc_mixer_control is used consistently among the drivers. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Arun KS <arunks@mistralsolutions.com> Cc: Misael Lopez Cruz <misael.lopez@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-07-04MFD: twl4030-audio: Rename platform dataPeter Ujfalusi
Allign the platform data names for twl4030 audio submodule: twl4030_audio_data: for the core MFD driver twl4030_codec_data: for ASoC codec driver twl4030_vibra_data: for the input/ForceFeedback driver To avoid breakage, change all depending drivers, files to use the new types. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-04MFD: twl4030-codec -> twl4030-audio: Rename the driverPeter Ujfalusi
Rename the driver, and header file from twl4030-codec to twl4030-audio. To avoid breakage change depending drivers at the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> CC: Misael Lopez Cruz <misael.lopez@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2011-05-26mfd: Use mfd cell platform_data for twl4030 codec cells platform bitsSamuel Ortiz
With the addition of a platform device mfd_cell pointer, MFD drivers can go back to passing platform data back to their sub drivers. This allows for an mfd_cell->mfd_data removal and thus keep the sub drivers MFD agnostic. This is mostly needed for non MFD aware sub drivers. Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-03-31Fix common misspellingsLucas De Marchi
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-23mfd: mfd_cell is now implicitly available to twl4030 driversAndres Salomon
The cell's platform_data is now accessed with a helper function; change clients to use that, and remove the now-unused data_size. Signed-off-by: Andres Salomon <dilinger@queued.net> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-12-14ASoC: TWL4030: Fix 24bit supportPeter Ujfalusi
twl4030 series of codecs supports S32_LE with msbits=24. Replace the S24_LE with S32_LE format, and add constraint for 24msbit in case of 32 S32_LE format. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-11-24Merge branch 'topic/asoc' of ↵Mark Brown
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 into for-2.6.38
2010-11-23Merge branch 'for-2.6.38' of ↵Takashi Iwai
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into topic/asoc Conflicts: sound/soc/codecs/tpa6130a2.c
2010-11-22ASoC: Do not include soc-dapm.hJarkko Nikula
There is no need to include soc-dapm.h since soc.h includes it. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-19ASoC: Move kfree(twl4030) to twl4030_soc_remove()Axel Lin
As we allocate memory for twl4030 in twl4030_codec_probe(), twl4030_codec_remove() is a better place to free the memory. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-11-06ASoC: Decouple DAPM from CODECsLiam Girdwood
Decoupling Dynamic Audio Power Management (DAPM) from codec devices is required when developing ASoC further. Such as for other ASoC components to have DAPM widgets or when extending DAPM to handle cross-device paths. This patch decouples DAPM related variables from struct snd_soc_codec and moves them to new struct snd_soc_dapm_context that is used to encapsulate DAPM context of a device. ASoC core and API of DAPM functions are modified to use DAPM context instead of codec. This patch does not change current functionality and a large part of changes come because of structure and internal API changes. Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some minor core changes, codecs and machine driver conversions from Jarkko Nikula <jhnikula@gmail.com>. Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Manuel Lauss <manuel.lauss@googlemail.com> Cc: Mike Frysinger <vapier.adi@gmail.com> Cc: Cliff Cai <cliff.cai@analog.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Ryan Mallon <ryan@bluewatersys.com> Cc: Timur Tabi <timur@freescale.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org> Cc: Wan ZongShun <mcuos.com@gmail.com> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Jassi Brar <jassi.brar@samsung.com> Cc: Daniel Gloeckner <dg@emlix.com> Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-10-26ASoC: TWL4030: Use usleep_range when appropriatePeter Ujfalusi
Change the busy loop delays with usleep_range or msleep calls. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-09-15ASoC: Remove needless codec->bias_level assignment to SND_SOC_BIAS_OFFJarkko Nikula
This assignment is done by the snd_soc_register_codec so there is no need to redo it in probe function of a codec driver. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-08-12ASoC: multi-component: TWL4030: Restore registers on removalPeter Ujfalusi
Add back the register restore call, when the codec driver is removed. This does not affect normal operation, but it is usefull when debugging audio through the twl4030 class codecs. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-08-12ASoC: multi-component - ASoC Multi-Component SupportLiam Girdwood
This patch extends the ASoC API to allow sound cards to have more than one CODEC and more than one platform DMA controller. This is achieved by dividing some current ASoC structures that contain both driver data and device data into structures that only either contain device data or driver data. i.e. struct snd_soc_codec ---> struct snd_soc_codec (device data) +-> struct snd_soc_codec_driver (driver data) struct snd_soc_platform ---> struct snd_soc_platform (device data) +-> struct snd_soc_platform_driver (driver data) struct snd_soc_dai ---> struct snd_soc_dai (device data) +-> struct snd_soc_dai_driver (driver data) struct snd_soc_device ---> deleted This now allows ASoC to be more tightly aligned with the Linux driver model and also means that every ASoC codec, platform and (platform) DAI is a kernel device. ASoC component private data is now stored as device private data. The ASoC sound card struct snd_soc_card has also been updated to store lists of it's components rather than a pointer to a codec and platform. The PCM runtime struct soc_pcm_runtime now has pointers to all its components. This patch adds DAPM support for ASoC multi-component and removes struct snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec or runtime PCM level basis rather than using snd_soc_socdev. Other notable multi-component changes:- * Stream operations now de-reference less structures. * close_delayed work() now runs on a DAI basis rather than looping all DAIs in a card. * PM suspend()/resume() operations can now handle N CODECs and Platforms per sound card. * Added soc_bind_dai_link() to bind the component devices to the sound card. * Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove DAI link components. * sysfs entries can now be registered per component per card. * snd_soc_new_pcms() functionailty rolled into dai_link_probe(). * snd_soc_register_codec() now does all the codec list and mutex init. This patch changes the probe() and remove() of the CODEC drivers as follows:- o Make CODEC driver a platform driver o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core. o Removed all static codec pointers (drivers now support > 1 codec dev) o snd_soc_register_pcms() now done by core. o snd_soc_register_dai() folded into snd_soc_register_codec(). CS4270 portions: Acked-by: Timur Tabi <timur@freescale.com> Some TLV320aic23 and Cirrus platform fixes. Signed-off-by: Ryan Mallon <ryan@bluewatersys.com> TI CODEC and OMAP fixes Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Samsung platform and misc fixes :- Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Jassi Brar <jassi.brar@samsung.com> Signed-off-by: Seungwhan Youn <sw.youn@samsung.com> MPC8610 and PPC fixes. Signed-off-by: Timur Tabi <timur@freescale.com> i.MX fixes and some core fixes. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> J4740 platform fixes:- Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> CC: Tony Lindgren <tony@atomide.com> CC: Nicolas Ferre <nicolas.ferre@atmel.com> CC: Kevin Hilman <khilman@deeprootsystems.com> CC: Sascha Hauer <s.hauer@pengutronix.de> CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp> CC: Kuninori Morimoto <morimoto.kuninori@renesas.com> CC: Daniel Gloeckner <dg@emlix.com> CC: Manuel Lauss <mano@roarinelk.homelinux.net> CC: Mike Frysinger <vapier.adi@gmail.com> CC: Arnaud Patard <apatard@mandriva.com> CC: Wan ZongShun <mcuos.com@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-08-04ASoC: TWL4030: Capture route runtime DAPM ordering fixPeter Ujfalusi
Fix the ordering problem in DAPM domain, when the user changes between digital and analog sources during active capture (or loopback) scenario. Before this patch, when the user changed from analog source to digital there were a short time, when the codec enabled analog mic bias (2.2 volts) instead of the correct digital mic bias (1.8 volts) to the digital microphones. This behaviour caused by the former implementation of selecting the correct type of bias. This was done at the POST_REG event of the DAPM_MUX_E("TXx Capture Route") widget. By moving the bias type selection as DAPM_SUPPLY and connecting it to the corresponding digimic widget the problematic situation can be avoided. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-07-27ASoC: TWL4030: Capture route DAPM event fixPeter Ujfalusi
There is no need to handle POST_PMU, POST_PMD event with the Capture Route widget. It is enough to handle POST_REG event, since that will come when the user changes the routing, and we will switch the needed bits in the registers. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-07-21ASoC: TWL4030: Add configurable delay after digimic enablePeter Ujfalusi
When digital microphones are connected to twl, delay is needed after enabling the digimic interface of the codec. Add new parameter for the setup data, which can be used to pass the apropriate delay in ms after the digimic interface has been enabled. Without certain delay (in certain HW configuration) the beggining of the recorded sample contains a glitch, which is generated by the digital microphones. Delaying the micbias1, 2 (which is the bias for the digimic0 or 1) does not help, since the glitch is coming after switching the digimic interface. Reversing the micbias and digimic enable order does not work either (in that case the wait need to be added after the micbias enabled). Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-07-13ASoC: TWL4030: DAC power optimizationPeter Ujfalusi
Restructure the DAPM connections in order to enable only the needed DAC (out of four in twl4030 series). I need to keep the 'AIF Enable' supply connected to the L2/R2 digital path, since the digital loopback needs AIF and APLL running. If no valid route available, than none of the DAC will be powered, but the AIF and APLL is going to be enabled. Furthermore, if only one audio path have valid route, than only the corresponding DAC will be powered. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsomicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-07-13ASoC: TWL4030: Fix for digital loopback gain rangePeter Ujfalusi
When the gain is configured using dB value it was not possible to use -24dB since the loopback got muted instead of -24dB. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsomicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-31Merge branch 'for-2.6.36' of ↵Takashi Iwai
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into topic/asoc
2010-05-31ASoC: TWL4030: Add functionalty to reset the registersPeter Ujfalusi
Machine driver can instruct the codec driver to reset the chip registers to their default values at probe time. If machine driver does not provide setup data, then the registers are going to be reseted to their defaults, to be safe. If the developer on the platform confirms that the register reset is not needed, than it can be skipped, saving ~20ms time in probe. As safety measure do the register reset at remove time also. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-31ASoC: TWL4030: Use BIAS_OFF instead of BIAS_STANDBY, when not in usePeter Ujfalusi
Restructure the codec power code in order to be able to hit off when the codec is not in use. Since the audio registers are accessible while the codec is powered down, there is no need for additional safety mechanism. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-31ASoC: TWL4030: Correct the ARXR2_APGA_CTL chip defaultPeter Ujfalusi
It seams at least on twl5031 that the ARXR2_APGA_CTL register does not have the same default value as it is written in the TRM. Since the codec part of the PM chip has not been actually changed according to TI, assuming, that all version has the same problem, so writing there the TRM value. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-31ASoC: TWL4030: Helper to check chip default registersPeter Ujfalusi
Since the twl4030 codec driver supports different version of the PM chip, a helper function can come handy, which can check the driver's default versus the chip values. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-31ASoC: TWL4030: Optimize the power up sequencePeter Ujfalusi
Since the reg cache now contains the chip default values for all registers (REG_OPTION is reset to it's default within this patch), there is no longer need to rewrite _all_ registers. Initialize only few selected registers. According to the latest information, the offset cancellation need to be done only once, when the codec is powered on, so there is no need for the power up wrapper. Move all chip initialization code under chip_init, and do it when the codec is initialized. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-31ASoC: TWL4030: Make offset cancellation path configurablePeter Ujfalusi
Add means for machine drivers to select the path for offset cancellation. Reset the reg cache value to the chip reset value at the same time. Machine drivers can specify which path need to be used for offset cancellation via the twl4030_setup.offset_cncl_path. For paths use the defines from include/linux/mfd/twl4030-codec.h: TWL4030_OFFSET_CNCL_SEL_* Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-31ASoC: TWL4030: Remove wrapper for power downPeter Ujfalusi
There is no need for the power down wrapper. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-24 20:59:41 +0000