From 0714a57c6865f31ed3366e5abdfae7da580d41d2 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 24 May 2011 11:53:29 -0700 Subject: xhci: Clear stopped_td when Stop Endpoint command completes. When an URB is cancelled, the xHCI driver issues a Stop Endpoint command so that it can manipulate the ring and remove the transfer. The xHC hardware then places a transfer event with the completion code "Stopped" or "Stopped Invalid" to let the driver know what TD it was in the middle of processing. This TD and TRB is stored in ep->stopped_td and ep->stopped_trb. These pointers are also used in handling stalled endpoints. By design, the Stop Endpoint command can race with URB completion. By the time the Stop Endpoint command is handled, the URBs to be cancelled may have been given back to the driver. Unfortunately, the stopped_td and stopped_trb pointers were not getting cleared in this case. The USB core unconditionally tries to reset the toggle bits on any endpoints when a new alternate interface setting is installed. When the xHCI driver saw that ep->stopped_td was still set from the Stop Endpoint command, xhci_reset_endpoint assumed the endpoint was actually stalled, and attempted to clean up the endpoint rings. This would manifest itself in a failed Reset Endpoint command and failed Set TR dequeue Pointer command after a successful Configure Endpoint command. It may have also been causing driver oops when the stopped_td was accessed. This patch should be backported to stable kernels since 2.6.31. Before 2.6.33, stopped_td was found in the xhci_endpoint_ring, not the xhci_virt_ep. Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 237a765f8d1..ba551239d28 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -692,6 +692,8 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci, if (list_empty(&ep->cancelled_td_list)) { xhci_stop_watchdog_timer_in_irq(xhci, ep); + ep->stopped_td = NULL; + ep->stopped_trb = NULL; ring_doorbell_for_active_rings(xhci, slot_id, ep_index); return; } -- cgit v1.2.3 From fe6c6c13d8dcb32398eef143e2e8efc3fb4019bf Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 23 May 2011 16:41:17 -0700 Subject: xhci: Don't submit commands when the host is dead. When the xHCI host controller dies, the USB core may attempt to reset the devices to their default configuration before disconnecting them. This causes calls into the xHCI bandwidth allocation functions. Don't allow those functions to submit commands or work on xHCI structures if the host controller is marked as dying. Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 8f2a56ece44..58183d2a808 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -1314,8 +1314,10 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, if (ret <= 0) return ret; xhci = hcd_to_xhci(hcd); - xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev); + if (xhci->xhc_state & XHCI_STATE_DYING) + return -ENODEV; + xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev); drop_flag = xhci_get_endpoint_flag(&ep->desc); if (drop_flag == SLOT_FLAG || drop_flag == EP0_FLAG) { xhci_dbg(xhci, "xHCI %s - can't drop slot or ep 0 %#x\n", @@ -1401,6 +1403,8 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, return ret; } xhci = hcd_to_xhci(hcd); + if (xhci->xhc_state & XHCI_STATE_DYING) + return -ENODEV; added_ctxs = xhci_get_endpoint_flag(&ep->desc); last_ctx = xhci_last_valid_endpoint(added_ctxs); @@ -1676,6 +1680,8 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) if (ret <= 0) return ret; xhci = hcd_to_xhci(hcd); + if (xhci->xhc_state & XHCI_STATE_DYING) + return -ENODEV; xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev); virt_dev = xhci->devs[udev->slot_id]; -- cgit v1.2.3 From 380032c3c855ded74c43252a0adb8e8d7afc9f45 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 5 Apr 2011 13:33:56 -0700 Subject: xhci: STFU: Remove function tracing. Remove unnecessary debugging from the xHCI driver. We don't need to know what function we're calling or returning from. Now I know how to use markup-oops.pl to de-mystify stack dumps of crashes. Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 8 -------- 1 file changed, 8 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index ba551239d28..4794905d38d 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2182,7 +2182,6 @@ static int xhci_handle_event(struct xhci_hcd *xhci) int update_ptrs = 1; int ret; - xhci_dbg(xhci, "In %s\n", __func__); if (!xhci->event_ring || !xhci->event_ring->dequeue) { xhci->error_bitmask |= 1 << 1; return 0; @@ -2195,7 +2194,6 @@ static int xhci_handle_event(struct xhci_hcd *xhci) xhci->error_bitmask |= 1 << 2; return 0; } - xhci_dbg(xhci, "%s - OS owns TRB\n", __func__); /* * Barrier between reading the TRB_CYCLE (valid) flag above and any @@ -2205,20 +2203,14 @@ static int xhci_handle_event(struct xhci_hcd *xhci) /* FIXME: Handle more event types. */ switch ((le32_to_cpu(event->event_cmd.flags) & TRB_TYPE_BITMASK)) { case TRB_TYPE(TRB_COMPLETION): - xhci_dbg(xhci, "%s - calling handle_cmd_completion\n", __func__); handle_cmd_completion(xhci, &event->event_cmd); - xhci_dbg(xhci, "%s - returned from handle_cmd_completion\n", __func__); break; case TRB_TYPE(TRB_PORT_STATUS): - xhci_dbg(xhci, "%s - calling handle_port_status\n", __func__); handle_port_status(xhci, event); - xhci_dbg(xhci, "%s - returned from handle_port_status\n", __func__); update_ptrs = 0; break; case TRB_TYPE(TRB_TRANSFER): - xhci_dbg(xhci, "%s - calling handle_tx_event\n", __func__); ret = handle_tx_event(xhci, &event->trans_event); - xhci_dbg(xhci, "%s - returned from handle_tx_event\n", __func__); if (ret < 0) xhci->error_bitmask |= 1 << 9; else -- cgit v1.2.3 From 5153b7b39105d8beb38e1c3f26ab4b877960d8e1 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 5 Apr 2011 13:33:56 -0700 Subject: xhci: STFU: Don't print event ring dequeue pointer. Stop printing out the event ring dequeue pointer and status register in the operational register set. The host will report an OK status 99% of the time the interrupt handler is called, and usually when it's really hosed, a host controller won't even call the interrupt handler. So the line is really useless. Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 14 +------------- 1 file changed, 1 insertion(+), 13 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 4794905d38d..f1ae1723403 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -167,9 +167,7 @@ static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer next = ring->dequeue; } addr = (unsigned long long) xhci_trb_virt_to_dma(ring->deq_seg, ring->dequeue); - if (ring == xhci->event_ring) - xhci_dbg(xhci, "Event ring deq = 0x%llx (DMA)\n", addr); - else if (ring == xhci->cmd_ring) + if (ring == xhci->cmd_ring) xhci_dbg(xhci, "Command ring deq = 0x%llx (DMA)\n", addr); else xhci_dbg(xhci, "Ring deq = 0x%llx (DMA)\n", addr); @@ -2267,16 +2265,6 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) spin_unlock(&xhci->lock); return IRQ_NONE; } - xhci_dbg(xhci, "op reg status = %08x\n", status); - xhci_dbg(xhci, "Event ring dequeue ptr:\n"); - xhci_dbg(xhci, "@%llx %08x %08x %08x %08x\n", - (unsigned long long) - xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, trb), - lower_32_bits(le64_to_cpu(trb->link.segment_ptr)), - upper_32_bits(le64_to_cpu(trb->link.segment_ptr)), - (unsigned int) le32_to_cpu(trb->link.intr_target), - (unsigned int) le32_to_cpu(trb->link.control)); - if (status & STS_FATAL) { xhci_warn(xhci, "WARNING: Host System Error\n"); xhci_halt(xhci); -- cgit v1.2.3 From f444ff27e9b8c953eef49da65c649fdcd202165a Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 5 Apr 2011 15:53:47 -0700 Subject: xhci: STFU: Be quieter during URB submission and completion. Unsurprisingly, URBs get submitted and completed a lot in the xHCI driver. If we have to print 10 lines of debug for every URB submitted or completed, then that can cause the whole system to stay in the interrupt handler too long, and can cause Missed Service completion codes for isochronous transfers. Cut down the debugging in the URB submission and completion paths: - Don't squawk about successful transfers, only unsuccessful ones. - Only print the number of bytes transferred if this was a short transfer. - Don't print the endpoint index for successful transfers (will add more debug to failed transfers to show endpoint index there later). - Stop printing MMIO writes. This debugging shows up when the endpoint doorbell is rung a to start a transfer (basically for every URB). - Don't print out the ring enqueue and dequeue pointers - Stop printing when we're pointing to a link TRB. Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 46 +++++++++++++++----------------------------- drivers/usb/host/xhci.h | 6 ------ 2 files changed, 15 insertions(+), 37 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index f1ae1723403..d1498c03c4c 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -167,10 +167,6 @@ static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer next = ring->dequeue; } addr = (unsigned long long) xhci_trb_virt_to_dma(ring->deq_seg, ring->dequeue); - if (ring == xhci->cmd_ring) - xhci_dbg(xhci, "Command ring deq = 0x%llx (DMA)\n", addr); - else - xhci_dbg(xhci, "Ring deq = 0x%llx (DMA)\n", addr); } /* @@ -246,12 +242,6 @@ static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, next = ring->enqueue; } addr = (unsigned long long) xhci_trb_virt_to_dma(ring->enq_seg, ring->enqueue); - if (ring == xhci->event_ring) - xhci_dbg(xhci, "Event ring enq = 0x%llx (DMA)\n", addr); - else if (ring == xhci->cmd_ring) - xhci_dbg(xhci, "Command ring enq = 0x%llx (DMA)\n", addr); - else - xhci_dbg(xhci, "Ring enq = 0x%llx (DMA)\n", addr); } /* @@ -634,13 +624,11 @@ static void xhci_giveback_urb_in_irq(struct xhci_hcd *xhci, } } usb_hcd_unlink_urb_from_ep(hcd, urb); - xhci_dbg(xhci, "Giveback %s URB %p\n", adjective, urb); spin_unlock(&xhci->lock); usb_hcd_giveback_urb(hcd, urb, status); xhci_urb_free_priv(xhci, urb_priv); spin_lock(&xhci->lock); - xhci_dbg(xhci, "%s URB given back\n", adjective); } } @@ -1630,7 +1618,6 @@ static int process_ctrl_td(struct xhci_hcd *xhci, struct xhci_td *td, "without IOC set??\n"); *status = -ESHUTDOWN; } else { - xhci_dbg(xhci, "Successful control transfer!\n"); *status = 0; } break; @@ -1727,7 +1714,6 @@ static int process_isoc_td(struct xhci_hcd *xhci, struct xhci_td *td, switch (trb_comp_code) { case COMP_SUCCESS: frame->status = 0; - xhci_dbg(xhci, "Successful isoc transfer!\n"); break; case COMP_SHORT_TX: frame->status = td->urb->transfer_flags & URB_SHORT_NOT_OK ? @@ -1837,12 +1823,6 @@ static int process_bulk_intr_td(struct xhci_hcd *xhci, struct xhci_td *td, else *status = 0; } else { - if (usb_endpoint_xfer_bulk(&td->urb->ep->desc)) - xhci_dbg(xhci, "Successful bulk " - "transfer!\n"); - else - xhci_dbg(xhci, "Successful interrupt " - "transfer!\n"); *status = 0; } break; @@ -1856,11 +1836,12 @@ static int process_bulk_intr_td(struct xhci_hcd *xhci, struct xhci_td *td, /* Others already handled above */ break; } - xhci_dbg(xhci, "ep %#x - asked for %d bytes, " - "%d bytes untransferred\n", - td->urb->ep->desc.bEndpointAddress, - td->urb->transfer_buffer_length, - TRB_LEN(le32_to_cpu(event->transfer_len))); + if (trb_comp_code == COMP_SHORT_TX) + xhci_dbg(xhci, "ep %#x - asked for %d bytes, " + "%d bytes untransferred\n", + td->urb->ep->desc.bEndpointAddress, + td->urb->transfer_buffer_length, + TRB_LEN(le32_to_cpu(event->transfer_len))); /* Fast path - was this the last TRB in the TD for this URB? */ if (event_trb == td->last_trb) { if (TRB_LEN(le32_to_cpu(event->transfer_len)) != 0) { @@ -1954,7 +1935,6 @@ static int handle_tx_event(struct xhci_hcd *xhci, /* Endpoint ID is 1 based, our index is zero based */ ep_index = TRB_TO_EP_ID(le32_to_cpu(event->flags)) - 1; - xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index); ep = &xdev->eps[ep_index]; ep_ring = xhci_dma_to_transfer_ring(ep, le64_to_cpu(event->buffer)); ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index); @@ -2149,9 +2129,15 @@ cleanup: xhci_urb_free_priv(xhci, urb_priv); usb_hcd_unlink_urb_from_ep(bus_to_hcd(urb->dev->bus), urb); - xhci_dbg(xhci, "Giveback URB %p, len = %d, " - "status = %d\n", - urb, urb->actual_length, status); + if ((urb->actual_length != urb->transfer_buffer_length && + (urb->transfer_flags & + URB_SHORT_NOT_OK)) || + status != 0) + xhci_dbg(xhci, "Giveback URB %p, len = %d, " + "expected = %x, status = %d\n", + urb, urb->actual_length, + urb->transfer_buffer_length, + status); spin_unlock(&xhci->lock); usb_hcd_giveback_urb(bus_to_hcd(urb->dev->bus), urb, status); spin_lock(&xhci->lock); @@ -2379,7 +2365,6 @@ static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, u32 ep_state, unsigned int num_trbs, gfp_t mem_flags) { /* Make sure the endpoint has been added to xHC schedule */ - xhci_dbg(xhci, "Endpoint state = 0x%x\n", ep_state); switch (ep_state) { case EP_STATE_DISABLED: /* @@ -2416,7 +2401,6 @@ static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, struct xhci_ring *ring = ep_ring; union xhci_trb *next; - xhci_dbg(xhci, "prepare_ring: pointing to link trb\n"); next = ring->enqueue; while (last_trb(xhci, ring, ring->enq_seg, next)) { diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index e12db7cfb9b..0772a8cfea2 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1338,9 +1338,6 @@ static inline unsigned int xhci_readl(const struct xhci_hcd *xhci, static inline void xhci_writel(struct xhci_hcd *xhci, const unsigned int val, __le32 __iomem *regs) { - xhci_dbg(xhci, - "`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n", - regs, val); writel(val, regs); } @@ -1368,9 +1365,6 @@ static inline void xhci_write_64(struct xhci_hcd *xhci, u32 val_lo = lower_32_bits(val); u32 val_hi = upper_32_bits(val); - xhci_dbg(xhci, - "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n", - regs, (long unsigned int) val); writel(val_lo, ptr); writel(val_hi, ptr + 1); } -- cgit v1.2.3 From 7fe4fc881d1340f17396f52c836e597dadadea42 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Wed, 25 May 2011 10:33:17 -0700 Subject: Intel xhci: Add PCI id for Panther Point xHCI host. This adds the PCI ID for the xHCI (USB 3.0) host controller in the Intel Panther Point chipset. It will be used by both the EHCI and xHCI driver in the following patches. Signed-off-by: Sarah Sharp --- include/linux/pci_ids.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 24787b75128..a311008af5e 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -2483,6 +2483,7 @@ #define PCI_DEVICE_ID_INTEL_COUGARPOINT_LPC_MAX 0x1c5f #define PCI_DEVICE_ID_INTEL_PATSBURG_LPC_0 0x1d40 #define PCI_DEVICE_ID_INTEL_PATSBURG_LPC_1 0x1d41 +#define PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI 0x1e31 #define PCI_DEVICE_ID_INTEL_PANTHERPOINT_LPC_MIN 0x1e40 #define PCI_DEVICE_ID_INTEL_PANTHERPOINT_LPC_MAX 0x1e5f #define PCI_DEVICE_ID_INTEL_DH89XXCC_LPC_MIN 0x2310 -- cgit v1.2.3 From 69e848c2090aebba5698a1620604c7dccb448684 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 22 Feb 2011 09:57:15 -0800 Subject: Intel xhci: Support EHCI/xHCI port switching. The Intel Panther Point chipsets contain an EHCI and xHCI host controller that shares some number of skew-dependent ports. These ports can be switched from the EHCI to the xHCI host (and vice versa) by a hardware MUX that is controlled by registers in the xHCI PCI configuration space. The USB 3.0 SuperSpeed terminations on the xHCI ports can be controlled separately from the USB 2.0 data wires. This switchover mechanism is there to support users who do a custom install of certain non-Linux operating systems that don't have official USB 3.0 support. By default, the ports are under EHCI, SuperSpeed terminations are off, and USB 3.0 devices will show up under the EHCI controller at reduced speeds. (This was more palatable for the marketing folks than having completely dead USB 3.0 ports if no xHCI drivers are available.) Users should be able to turn on xHCI by default through a BIOS option, but users are happiest when they don't have to change random BIOS settings. This patch introduces a driver method to switchover the ports from EHCI to xHCI before the EHCI driver finishes PCI enumeration. We want to switch the ports over before the USB core has the chance to enumerate devices under EHCI, or boot from USB mass storage will fail if the boot device connects under EHCI first, and then gets disconnected when the port switches over to xHCI. Add code to the xHCI PCI quirk to switch the ports from EHCI to xHCI. The PCI quirks code will run before any other PCI probe function is called, so this avoids the issue with boot devices. Another issue is with BIOS behavior during system resume from hibernate. If the BIOS doesn't support xHCI, it may switch the devices under EHCI to allow use of the USB keyboard, mice, and mass storage devices. It's supposed to remember the value of the port routing registers and switch them back when the OS attempts to take control of the xHCI host controller, but we all know not to trust BIOS writers. Make both the xHCI driver and the EHCI driver attempt to switchover the ports in their PCI resume functions. We can't guarantee which PCI device will be resumed first, so this avoids any race conditions. Writing a '1' to an already set port switchover bit or a '0' to a cleared port switchover bit should have no effect. The xHCI PCI configuration registers will be documented in the EDS-level chipset spec, which is not public yet. I have permission from legal and the Intel chipset group to release this patch early to allow good Linux support at product launch. I've tried to document the registers as much as possible, so please let me know if anything is unclear. Signed-off-by: Sarah Sharp --- drivers/usb/host/ehci-pci.c | 39 +++++++++++++++++++++++++++ drivers/usb/host/pci-quirks.c | 63 +++++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/pci-quirks.h | 2 ++ drivers/usb/host/xhci-pci.c | 20 ++++++++++++++ 4 files changed, 124 insertions(+) diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index 660b80a75ca..1102ce65a3a 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -348,11 +348,50 @@ static int ehci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) return rc; } +static bool usb_is_intel_switchable_ehci(struct pci_dev *pdev) +{ + return pdev->class == PCI_CLASS_SERIAL_USB_EHCI && + pdev->vendor == PCI_VENDOR_ID_INTEL && + pdev->device == 0x1E26; +} + +static void ehci_enable_xhci_companion(void) +{ + struct pci_dev *companion = NULL; + + /* The xHCI and EHCI controllers are not on the same PCI slot */ + for_each_pci_dev(companion) { + if (!usb_is_intel_switchable_xhci(companion)) + continue; + usb_enable_xhci_ports(companion); + return; + } +} + static int ehci_pci_resume(struct usb_hcd *hcd, bool hibernated) { struct ehci_hcd *ehci = hcd_to_ehci(hcd); struct pci_dev *pdev = to_pci_dev(hcd->self.controller); + /* The BIOS on systems with the Intel Panther Point chipset may or may + * not support xHCI natively. That means that during system resume, it + * may switch the ports back to EHCI so that users can use their + * keyboard to select a kernel from GRUB after resume from hibernate. + * + * The BIOS is supposed to remember whether the OS had xHCI ports + * enabled before resume, and switch the ports back to xHCI when the + * BIOS/OS semaphore is written, but we all know we can't trust BIOS + * writers. + * + * Unconditionally switch the ports back to xHCI after a system resume. + * We can't tell whether the EHCI or xHCI controller will be resumed + * first, so we have to do the port switchover in both drivers. Writing + * a '1' to the port switchover registers should have no effect if the + * port was already switched over. + */ + if (usb_is_intel_switchable_ehci(pdev)) + ehci_enable_xhci_companion(); + // maybe restore FLADJ if (time_before(jiffies, ehci->next_statechange)) diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c index f16c59d5f48..fd930618c28 100644 --- a/drivers/usb/host/pci-quirks.c +++ b/drivers/usb/host/pci-quirks.c @@ -69,6 +69,9 @@ #define NB_PIF0_PWRDOWN_0 0x01100012 #define NB_PIF0_PWRDOWN_1 0x01100013 +#define USB_INTEL_XUSB2PR 0xD0 +#define USB_INTEL_USB3_PSSEN 0xD8 + static struct amd_chipset_info { struct pci_dev *nb_dev; struct pci_dev *smbus_dev; @@ -673,6 +676,64 @@ static int handshake(void __iomem *ptr, u32 mask, u32 done, return -ETIMEDOUT; } +bool usb_is_intel_switchable_xhci(struct pci_dev *pdev) +{ + return pdev->class == PCI_CLASS_SERIAL_USB_XHCI && + pdev->vendor == PCI_VENDOR_ID_INTEL && + pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI; +} +EXPORT_SYMBOL_GPL(usb_is_intel_switchable_xhci); + +/* + * Intel's Panther Point chipset has two host controllers (EHCI and xHCI) that + * share some number of ports. These ports can be switched between either + * controller. Not all of the ports under the EHCI host controller may be + * switchable. + * + * The ports should be switched over to xHCI before PCI probes for any device + * start. This avoids active devices under EHCI being disconnected during the + * port switchover, which could cause loss of data on USB storage devices, or + * failed boot when the root file system is on a USB mass storage device and is + * enumerated under EHCI first. + * + * We write into the xHC's PCI configuration space in some Intel-specific + * registers to switch the ports over. The USB 3.0 terminations and the USB + * 2.0 data wires are switched separately. We want to enable the SuperSpeed + * terminations before switching the USB 2.0 wires over, so that USB 3.0 + * devices connect at SuperSpeed, rather than at USB 2.0 speeds. + */ +void usb_enable_xhci_ports(struct pci_dev *xhci_pdev) +{ + u32 ports_available; + + ports_available = 0xffffffff; + /* Write USB3_PSSEN, the USB 3.0 Port SuperSpeed Enable + * Register, to turn on SuperSpeed terminations for all + * available ports. + */ + pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN, + cpu_to_le32(ports_available)); + + pci_read_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN, + &ports_available); + dev_dbg(&xhci_pdev->dev, "USB 3.0 ports that are now enabled " + "under xHCI: 0x%x\n", ports_available); + + ports_available = 0xffffffff; + /* Write XUSB2PR, the xHC USB 2.0 Port Routing Register, to + * switch the USB 2.0 power and data lines over to the xHCI + * host. + */ + pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR, + cpu_to_le32(ports_available)); + + pci_read_config_dword(xhci_pdev, USB_INTEL_XUSB2PR, + &ports_available); + dev_dbg(&xhci_pdev->dev, "USB 2.0 ports that are now switched over " + "to xHCI: 0x%x\n", ports_available); +} +EXPORT_SYMBOL_GPL(usb_enable_xhci_ports); + /** * PCI Quirks for xHCI. * @@ -732,6 +793,8 @@ static void __devinit quirk_usb_handoff_xhci(struct pci_dev *pdev) writel(XHCI_LEGACY_DISABLE_SMI, base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET); + if (usb_is_intel_switchable_xhci(pdev)) + usb_enable_xhci_ports(pdev); hc_init: op_reg_base = base + XHCI_HC_LENGTH(readl(base)); diff --git a/drivers/usb/host/pci-quirks.h b/drivers/usb/host/pci-quirks.h index 6ae9f78e993..b1002a8ef96 100644 --- a/drivers/usb/host/pci-quirks.h +++ b/drivers/usb/host/pci-quirks.h @@ -8,6 +8,8 @@ int usb_amd_find_chipset_info(void); void usb_amd_dev_put(void); void usb_amd_quirk_pll_disable(void); void usb_amd_quirk_pll_enable(void); +bool usb_is_intel_switchable_xhci(struct pci_dev *pdev); +void usb_enable_xhci_ports(struct pci_dev *xhci_pdev); #else static inline void usb_amd_quirk_pll_disable(void) {} static inline void usb_amd_quirk_pll_enable(void) {} diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index cbc4d491e62..faf039ac657 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -242,8 +242,28 @@ static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) static int xhci_pci_resume(struct usb_hcd *hcd, bool hibernated) { struct xhci_hcd *xhci = hcd_to_xhci(hcd); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); int retval = 0; + /* The BIOS on systems with the Intel Panther Point chipset may or may + * not support xHCI natively. That means that during system resume, it + * may switch the ports back to EHCI so that users can use their + * keyboard to select a kernel from GRUB after resume from hibernate. + * + * The BIOS is supposed to remember whether the OS had xHCI ports + * enabled before resume, and switch the ports back to xHCI when the + * BIOS/OS semaphore is written, but we all know we can't trust BIOS + * writers. + * + * Unconditionally switch the ports back to xHCI after a system resume. + * We can't tell whether the EHCI or xHCI controller will be resumed + * first, so we have to do the port switchover in both drivers. Writing + * a '1' to the port switchover registers should have no effect if the + * port was already switched over. + */ + if (usb_is_intel_switchable_xhci(pdev)) + usb_enable_xhci_ports(pdev); + retval = xhci_resume(xhci, hibernated); return retval; } -- cgit v1.2.3 From ad808333d8201d53075a11bc8dd83b81f3d68f0b Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Wed, 25 May 2011 10:43:56 -0700 Subject: Intel xhci: Ignore spurious successful event. The xHCI host controller in the Panther Point chipset sometimes produces spurious events on the event ring. If it receives a short packet, it first puts a Transfer Event with a short transfer completion code on the event ring. Then it puts a Transfer Event with a successful completion code on the ring for the same TD. The xHCI driver correctly processes the short transfer completion code, gives the URB back to the driver, and then prints a warning in dmesg about the spurious event. These warning messages really fill up dmesg when an HD webcam is plugged into xHCI. This spurious successful event behavior isn't technically disallowed by the xHCI specification, so make the xHCI driver just ignore the spurious completion event. Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-pci.c | 4 ++++ drivers/usb/host/xhci-ring.c | 14 ++++++++++++++ drivers/usb/host/xhci.h | 2 ++ 3 files changed, 20 insertions(+) diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index faf039ac657..eafd17fae94 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -118,6 +118,10 @@ static int xhci_pci_setup(struct usb_hcd *hcd) /* AMD PLL quirk */ if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info()) xhci->quirks |= XHCI_AMD_PLL_FIX; + if (pdev->vendor == PCI_VENDOR_ID_INTEL && + pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI) { + xhci->quirks |= XHCI_SPURIOUS_SUCCESS; + } /* Make sure the HC is halted. */ retval = xhci_halt(xhci); diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index d1498c03c4c..56f6c584c65 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2061,6 +2061,16 @@ static int handle_tx_event(struct xhci_hcd *xhci, if (!event_seg) { if (!ep->skip || !usb_endpoint_xfer_isoc(&td->urb->ep->desc)) { + /* Some host controllers give a spurious + * successful event after a short transfer. + * Ignore it. + */ + if ((xhci->quirks & XHCI_SPURIOUS_SUCCESS) && + ep_ring->last_td_was_short) { + ep_ring->last_td_was_short = false; + ret = 0; + goto cleanup; + } /* HC is busted, give up! */ xhci_err(xhci, "ERROR Transfer event TRB DMA ptr not " @@ -2071,6 +2081,10 @@ static int handle_tx_event(struct xhci_hcd *xhci, ret = skip_isoc_td(xhci, td, event, ep, &status); goto cleanup; } + if (trb_comp_code == COMP_SHORT_TX) + ep_ring->last_td_was_short = true; + else + ep_ring->last_td_was_short = false; if (ep->skip) { xhci_dbg(xhci, "Found td. Clear skip flag.\n"); diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 0772a8cfea2..5cfeb8614b8 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1123,6 +1123,7 @@ struct xhci_ring { */ u32 cycle_state; unsigned int stream_id; + bool last_td_was_short; }; struct xhci_erst_entry { @@ -1290,6 +1291,7 @@ struct xhci_hcd { #define XHCI_RESET_EP_QUIRK (1 << 1) #define XHCI_NEC_HOST (1 << 2) #define XHCI_AMD_PLL_FIX (1 << 3) +#define XHCI_SPURIOUS_SUCCESS (1 << 4) /* There are two roothubs to keep track of bus suspend info for */ struct xhci_bus_state bus_state[2]; /* Is each xHCI roothub port a USB 3.0, USB 2.0, or USB 1.1 port? */ -- cgit v1.2.3 From 2cf95c18d5069e13c02a8667d91e064df8e17e09 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Wed, 11 May 2011 16:14:58 -0700 Subject: Intel xhci: Limit number of active endpoints to 64. The Panther Point chipset has an xHCI host controller that has a limit to the number of active endpoints it can handle. Ideally, it would signal that it can't handle anymore endpoints by returning a Resource Error for the Configure Endpoint command, but they don't. Instead it needs software to keep track of the number of active endpoints, across configure endpoint commands, reset device commands, disable slot commands, and address device commands. Add a new endpoint context counter, xhci_hcd->num_active_eps, and use it to track the number of endpoints the xHC has active. This gets a little tricky, because commands to change the number of active endpoints can fail. This patch adds a new xHCI quirk for these Intel hosts, and the new code should not have any effect on other xHCI host controllers. Fail a new device allocation if we don't have room for the new default control endpoint. Use the endpoint ring pointers to determine what endpoints were active before a Reset Device command or a Disable Slot command, and drop those once the command completes. Fail a configure endpoint command if it would add too many new endpoints. We have to be a bit over zealous here, and only count the number of new endpoints to be added, without subtracting the number of dropped endpoints. That's because a second configure endpoint command for a different device could sneak in before we know if the first command is completed. If the first command dropped resources, the host controller fails the command for some reason, and we're nearing the limit of endpoints, we could end up oversubscribing the host. To fix this race condition, when evaluating whether a configure endpoint command will fix in our bandwidth budget, only add the new endpoints to xhci->num_active_eps, and don't subtract the dropped endpoints. Ignore changed endpoints (ones that are dropped and then re-added), as that shouldn't effect the host's endpoint resources. When the configure endpoint command completes, subtract off the dropped endpoints. This may mean some configuration changes may temporarily fail, but it's always better to under-subscribe than over-subscribe resources. (Originally my plan had been to push the resource allocation down into the ring allocation functions. However, that would cause us to allocate unnecessary resources when endpoints were changed, because the xHCI driver allocates a new ring for the changed endpoint, and only deletes the old ring once the Configure Endpoint command succeeds. A further complication would have been dealing with the per-device endpoint ring cache.) Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-pci.c | 2 + drivers/usb/host/xhci-ring.c | 7 +- drivers/usb/host/xhci.c | 232 +++++++++++++++++++++++++++++++++++++++++-- drivers/usb/host/xhci.h | 14 +++ 4 files changed, 244 insertions(+), 11 deletions(-) diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index eafd17fae94..c408e9f6a70 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -121,6 +121,8 @@ static int xhci_pci_setup(struct usb_hcd *hcd) if (pdev->vendor == PCI_VENDOR_ID_INTEL && pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI) { xhci->quirks |= XHCI_SPURIOUS_SUCCESS; + xhci->quirks |= XHCI_EP_LIMIT_QUIRK; + xhci->limit_active_eps = 64; } /* Make sure the HC is halted. */ diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 56f6c584c65..cc1485bfed3 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1081,8 +1081,13 @@ static void handle_cmd_completion(struct xhci_hcd *xhci, complete(&xhci->addr_dev); break; case TRB_TYPE(TRB_DISABLE_SLOT): - if (xhci->devs[slot_id]) + if (xhci->devs[slot_id]) { + if (xhci->quirks & XHCI_EP_LIMIT_QUIRK) + /* Delete default control endpoint resources */ + xhci_free_device_endpoint_resources(xhci, + xhci->devs[slot_id], true); xhci_free_virt_device(xhci, slot_id); + } break; case TRB_TYPE(TRB_CONFIG_EP): virt_dev = xhci->devs[slot_id]; diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 58183d2a808..d9660eb97eb 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -1582,6 +1582,113 @@ static int xhci_evaluate_context_result(struct xhci_hcd *xhci, return ret; } +static u32 xhci_count_num_new_endpoints(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + struct xhci_input_control_ctx *ctrl_ctx; + u32 valid_add_flags; + u32 valid_drop_flags; + + ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx); + /* Ignore the slot flag (bit 0), and the default control endpoint flag + * (bit 1). The default control endpoint is added during the Address + * Device command and is never removed until the slot is disabled. + */ + valid_add_flags = ctrl_ctx->add_flags >> 2; + valid_drop_flags = ctrl_ctx->drop_flags >> 2; + + /* Use hweight32 to count the number of ones in the add flags, or + * number of endpoints added. Don't count endpoints that are changed + * (both added and dropped). + */ + return hweight32(valid_add_flags) - + hweight32(valid_add_flags & valid_drop_flags); +} + +static unsigned int xhci_count_num_dropped_endpoints(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + struct xhci_input_control_ctx *ctrl_ctx; + u32 valid_add_flags; + u32 valid_drop_flags; + + ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx); + valid_add_flags = ctrl_ctx->add_flags >> 2; + valid_drop_flags = ctrl_ctx->drop_flags >> 2; + + return hweight32(valid_drop_flags) - + hweight32(valid_add_flags & valid_drop_flags); +} + +/* + * We need to reserve the new number of endpoints before the configure endpoint + * command completes. We can't subtract the dropped endpoints from the number + * of active endpoints until the command completes because we can oversubscribe + * the host in this case: + * + * - the first configure endpoint command drops more endpoints than it adds + * - a second configure endpoint command that adds more endpoints is queued + * - the first configure endpoint command fails, so the config is unchanged + * - the second command may succeed, even though there isn't enough resources + * + * Must be called with xhci->lock held. + */ +static int xhci_reserve_host_resources(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + u32 added_eps; + + added_eps = xhci_count_num_new_endpoints(xhci, in_ctx); + if (xhci->num_active_eps + added_eps > xhci->limit_active_eps) { + xhci_dbg(xhci, "Not enough ep ctxs: " + "%u active, need to add %u, limit is %u.\n", + xhci->num_active_eps, added_eps, + xhci->limit_active_eps); + return -ENOMEM; + } + xhci->num_active_eps += added_eps; + xhci_dbg(xhci, "Adding %u ep ctxs, %u now active.\n", added_eps, + xhci->num_active_eps); + return 0; +} + +/* + * The configure endpoint was failed by the xHC for some other reason, so we + * need to revert the resources that failed configuration would have used. + * + * Must be called with xhci->lock held. + */ +static void xhci_free_host_resources(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + u32 num_failed_eps; + + num_failed_eps = xhci_count_num_new_endpoints(xhci, in_ctx); + xhci->num_active_eps -= num_failed_eps; + xhci_dbg(xhci, "Removing %u failed ep ctxs, %u now active.\n", + num_failed_eps, + xhci->num_active_eps); +} + +/* + * Now that the command has completed, clean up the active endpoint count by + * subtracting out the endpoints that were dropped (but not changed). + * + * Must be called with xhci->lock held. + */ +static void xhci_finish_resource_reservation(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + u32 num_dropped_eps; + + num_dropped_eps = xhci_count_num_dropped_endpoints(xhci, in_ctx); + xhci->num_active_eps -= num_dropped_eps; + if (num_dropped_eps) + xhci_dbg(xhci, "Removing %u dropped ep ctxs, %u now active.\n", + num_dropped_eps, + xhci->num_active_eps); +} + /* Issue a configure endpoint command or evaluate context command * and wait for it to finish. */ @@ -1602,6 +1709,15 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, virt_dev = xhci->devs[udev->slot_id]; if (command) { in_ctx = command->in_ctx; + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK) && + xhci_reserve_host_resources(xhci, in_ctx)) { + spin_unlock_irqrestore(&xhci->lock, flags); + xhci_warn(xhci, "Not enough host resources, " + "active endpoint contexts = %u\n", + xhci->num_active_eps); + return -ENOMEM; + } + cmd_completion = command->completion; cmd_status = &command->status; command->command_trb = xhci->cmd_ring->enqueue; @@ -1617,6 +1733,14 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, list_add_tail(&command->cmd_list, &virt_dev->cmd_list); } else { in_ctx = virt_dev->in_ctx; + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK) && + xhci_reserve_host_resources(xhci, in_ctx)) { + spin_unlock_irqrestore(&xhci->lock, flags); + xhci_warn(xhci, "Not enough host resources, " + "active endpoint contexts = %u\n", + xhci->num_active_eps); + return -ENOMEM; + } cmd_completion = &virt_dev->cmd_completion; cmd_status = &virt_dev->cmd_status; } @@ -1631,6 +1755,8 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, if (ret < 0) { if (command) list_del(&command->cmd_list); + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) + xhci_free_host_resources(xhci, in_ctx); spin_unlock_irqrestore(&xhci->lock, flags); xhci_dbg(xhci, "FIXME allocate a new ring segment\n"); return -ENOMEM; @@ -1653,8 +1779,22 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, } if (!ctx_change) - return xhci_configure_endpoint_result(xhci, udev, cmd_status); - return xhci_evaluate_context_result(xhci, udev, cmd_status); + ret = xhci_configure_endpoint_result(xhci, udev, cmd_status); + else + ret = xhci_evaluate_context_result(xhci, udev, cmd_status); + + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) { + spin_lock_irqsave(&xhci->lock, flags); + /* If the command failed, remove the reserved resources. + * Otherwise, clean up the estimate to include dropped eps. + */ + if (ret) + xhci_free_host_resources(xhci, in_ctx); + else + xhci_finish_resource_reservation(xhci, in_ctx); + spin_unlock_irqrestore(&xhci->lock, flags); + } + return ret; } /* Called after one or more calls to xhci_add_endpoint() or @@ -2271,6 +2411,34 @@ int xhci_free_streams(struct usb_hcd *hcd, struct usb_device *udev, return 0; } +/* + * Deletes endpoint resources for endpoints that were active before a Reset + * Device command, or a Disable Slot command. The Reset Device command leaves + * the control endpoint intact, whereas the Disable Slot command deletes it. + * + * Must be called with xhci->lock held. + */ +void xhci_free_device_endpoint_resources(struct xhci_hcd *xhci, + struct xhci_virt_device *virt_dev, bool drop_control_ep) +{ + int i; + unsigned int num_dropped_eps = 0; + unsigned int drop_flags = 0; + + for (i = (drop_control_ep ? 0 : 1); i < 31; i++) { + if (virt_dev->eps[i].ring) { + drop_flags |= 1 << i; + num_dropped_eps++; + } + } + xhci->num_active_eps -= num_dropped_eps; + if (num_dropped_eps) + xhci_dbg(xhci, "Dropped %u ep ctxs, flags = 0x%x, " + "%u now active.\n", + num_dropped_eps, drop_flags, + xhci->num_active_eps); +} + /* * This submits a Reset Device Command, which will set the device state to 0, * set the device address to 0, and disable all the endpoints except the default @@ -2412,6 +2580,14 @@ int xhci_discover_or_reset_device(struct usb_hcd *hcd, struct usb_device *udev) goto command_cleanup; } + /* Free up host controller endpoint resources */ + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) { + spin_lock_irqsave(&xhci->lock, flags); + /* Don't delete the default control endpoint resources */ + xhci_free_device_endpoint_resources(xhci, virt_dev, false); + spin_unlock_irqrestore(&xhci->lock, flags); + } + /* Everything but endpoint 0 is disabled, so free or cache the rings. */ last_freed_endpoint = 1; for (i = 1; i < 31; ++i) { @@ -2484,6 +2660,27 @@ void xhci_free_dev(struct usb_hcd *hcd, struct usb_device *udev) */ } +/* + * Checks if we have enough host controller resources for the default control + * endpoint. + * + * Must be called with xhci->lock held. + */ +static int xhci_reserve_host_control_ep_resources(struct xhci_hcd *xhci) +{ + if (xhci->num_active_eps + 1 > xhci->limit_active_eps) { + xhci_dbg(xhci, "Not enough ep ctxs: " + "%u active, need to add 1, limit is %u.\n", + xhci->num_active_eps, xhci->limit_active_eps); + return -ENOMEM; + } + xhci->num_active_eps += 1; + xhci_dbg(xhci, "Adding 1 ep ctx, %u now active.\n", + xhci->num_active_eps); + return 0; +} + + /* * Returns 0 if the xHC ran out of device slots, the Enable Slot command * timed out, or allocating memory failed. Returns 1 on success. @@ -2519,24 +2716,39 @@ int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev) xhci_err(xhci, "Error while assigning device slot ID\n"); return 0; } - /* xhci_alloc_virt_device() does not touch rings; no need to lock. - * Use GFP_NOIO, since this function can be called from + + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) { + spin_lock_irqsave(&xhci->lock, flags); + ret = xhci_reserve_host_control_ep_resources(xhci); + if (ret) { + spin_unlock_irqrestore(&xhci->lock, flags); + xhci_warn(xhci, "Not enough host resources, " + "active endpoint contexts = %u\n", + xhci->num_active_eps); + goto disable_slot; + } + spin_unlock_irqrestore(&xhci->lock, flags); + } + /* Use GFP_NOIO, since this function can be called from * xhci_discover_or_reset_device(), which may be called as part of * mass storage driver error handling. */ if (!xhci_alloc_virt_device(xhci, xhci->slot_id, udev, GFP_NOIO)) { - /* Disable slot, if we can do it without mem alloc */ xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n"); - spin_lock_irqsave(&xhci->lock, flags); - if (!xhci_queue_slot_control(xhci, TRB_DISABLE_SLOT, udev->slot_id)) - xhci_ring_cmd_db(xhci); - spin_unlock_irqrestore(&xhci->lock, flags); - return 0; + goto disable_slot; } udev->slot_id = xhci->slot_id; /* Is this a LS or FS device under a HS hub? */ /* Hub or peripherial? */ return 1; + +disable_slot: + /* Disable slot, if we can do it without mem alloc */ + spin_lock_irqsave(&xhci->lock, flags); + if (!xhci_queue_slot_control(xhci, TRB_DISABLE_SLOT, udev->slot_id)) + xhci_ring_cmd_db(xhci); + spin_unlock_irqrestore(&xhci->lock, flags); + return 0; } /* diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 5cfeb8614b8..ac0196e7fcf 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1292,6 +1292,18 @@ struct xhci_hcd { #define XHCI_NEC_HOST (1 << 2) #define XHCI_AMD_PLL_FIX (1 << 3) #define XHCI_SPURIOUS_SUCCESS (1 << 4) +/* + * Certain Intel host controllers have a limit to the number of endpoint + * contexts they can handle. Ideally, they would signal that they can't handle + * anymore endpoint contexts by returning a Resource Error for the Configure + * Endpoint command, but they don't. Instead they expect software to keep track + * of the number of active endpoints for them, across configure endpoint + * commands, reset device commands, disable slot commands, and address device + * commands. + */ +#define XHCI_EP_LIMIT_QUIRK (1 << 5) + unsigned int num_active_eps; + unsigned int limit_active_eps; /* There are two roothubs to keep track of bus suspend info for */ struct xhci_bus_state bus_state[2]; /* Is each xHCI roothub port a USB 3.0, USB 2.0, or USB 1.1 port? */ @@ -1435,6 +1447,8 @@ void xhci_setup_streams_ep_input_ctx(struct xhci_hcd *xhci, void xhci_setup_no_streams_ep_input_ctx(struct xhci_hcd *xhci, struct xhci_ep_ctx *ep_ctx, struct xhci_virt_ep *ep); +void xhci_free_device_endpoint_resources(struct xhci_hcd *xhci, + struct xhci_virt_device *virt_dev, bool drop_control_ep); struct xhci_ring *xhci_dma_to_transfer_ring( struct xhci_virt_ep *ep, u64 address); -- cgit v1.2.3