From 00494be4546432a11d62ebfeca363256ff9822b5 Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Fri, 11 Jan 2013 14:45:58 +0000 Subject: networking/cs89x0.txt: delete stale information about hand patching Output of a git grep happened to make me look into this file, and I found instructions about how to hand patch (without using patch) the driver into the kernel tree. Since the driver has been a part of the mainline kernel for years, we can dump this whole section. Fortunately it doesn't even cause a renumbering of the sections to do so. Signed-off-by: Paul Gortmaker Signed-off-by: David S. Miller --- Documentation/networking/cs89x0.txt | 79 ------------------------------------- 1 file changed, 79 deletions(-) (limited to 'Documentation/networking') diff --git a/Documentation/networking/cs89x0.txt b/Documentation/networking/cs89x0.txt index c725d33b316..0e190180eec 100644 --- a/Documentation/networking/cs89x0.txt +++ b/Documentation/networking/cs89x0.txt @@ -36,7 +36,6 @@ TABLE OF CONTENTS 4.1 Compiling the Driver as a Loadable Module 4.2 Compiling the driver to support memory mode 4.3 Compiling the driver to support Rx DMA - 4.4 Compiling the Driver into the Kernel 5.0 TESTING AND TROUBLESHOOTING 5.1 Known Defects and Limitations @@ -364,84 +363,6 @@ The compile-time optionality for DMA was removed in the 2.3 kernel series. DMA support is now unconditionally part of the driver. It is enabled by the 'use_dma=1' module option. -4.4 COMPILING THE DRIVER INTO THE KERNEL - -If your Linux distribution already has support for the cs89x0 driver -then simply copy the source file to the /usr/src/linux/drivers/net -directory to replace the original ones and run the make utility to -rebuild the kernel. See Step 3 for rebuilding the kernel. - -If your Linux does not include the cs89x0 driver, you need to edit three -configuration files, copy the source file to the /usr/src/linux/drivers/net -directory, and then run the make utility to rebuild the kernel. - -1. Edit the following configuration files by adding the statements as -indicated. (When possible, try to locate the added text to the section of the -file containing similar statements). - - -a.) In /usr/src/linux/drivers/net/Config.in, add: - -tristate 'CS89x0 support' CONFIG_CS89x0 - -Example: - - if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then - tristate 'ICL EtherTeam 16i/32 support' CONFIG_ETH16I - fi - - tristate 'CS89x0 support' CONFIG_CS89x0 - - tristate 'NE2000/NE1000 support' CONFIG_NE2000 - if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then - tristate 'NI5210 support' CONFIG_NI52 - - -b.) In /usr/src/linux/drivers/net/Makefile, add the following lines: - -ifeq ($(CONFIG_CS89x0),y) -L_OBJS += cs89x0.o -else - ifeq ($(CONFIG_CS89x0),m) - M_OBJS += cs89x0.o - endif -endif - - -c.) In /linux/drivers/net/Space.c file, add the line: - -extern int cs89x0_probe(struct device *dev); - - -Example: - - extern int ultra_probe(struct device *dev); - extern int wd_probe(struct device *dev); - extern int el2_probe(struct device *dev); - - extern int cs89x0_probe(struct device *dev); - - extern int ne_probe(struct device *dev); - extern int hp_probe(struct device *dev); - extern int hp_plus_probe(struct device *dev); - - -Also add: - - #ifdef CONFIG_CS89x0 - { cs89x0_probe,0 }, - #endif - - -2.) Copy the driver source files (cs89x0.c and cs89x0.h) -into the /usr/src/linux/drivers/net directory. - - -3.) Go to /usr/src/linux directory and run 'make config' followed by 'make' -(or make bzImage) to rebuild the kernel. - -4.) Use the DOS 'setup' utility to disable plug and play on the NIC. - 5.0 TESTING AND TROUBLESHOOTING =============================================================================== -- cgit v1.2.3