From 74638c84821c066d02c158bc843c84499ddc9764 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Tue, 31 Mar 2009 20:15:28 +0200 Subject: ide: add support for CFA specified transfer modes (take 3) Add support for the CompactFlash specific PIO modes 5/6 and MWDMA modes 3/4. Since there were no PIO5 capable hard drives produced and one would also need 66 MHz IDE clock to actually get the difference WRT the address setup timings programmed, I decided to simply replace the old non-standard PIO mode 5 timings with the CFA specified ones. Signed-off-by: Sergei Shtylyov Cc: stf_xl@wp.pl Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/ide-timings.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) (limited to 'drivers/ide/ide-timings.c') diff --git a/drivers/ide/ide-timings.c b/drivers/ide/ide-timings.c index 81f527af8fa..001a56365be 100644 --- a/drivers/ide/ide-timings.c +++ b/drivers/ide/ide-timings.c @@ -43,6 +43,8 @@ static struct ide_timing ide_timing[] = { { XFER_UDMA_1, 0, 0, 0, 0, 0, 0, 0, 80 }, { XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 120 }, + { XFER_MW_DMA_4, 25, 0, 0, 0, 55, 20, 80, 0 }, + { XFER_MW_DMA_3, 25, 0, 0, 0, 65, 25, 100, 0 }, { XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 120, 0 }, { XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 150, 0 }, { XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 480, 0 }, @@ -51,7 +53,8 @@ static struct ide_timing ide_timing[] = { { XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 480, 0 }, { XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 960, 0 }, - { XFER_PIO_5, 20, 50, 30, 100, 50, 30, 100, 0 }, + { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 80, 0 }, + { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 100, 0 }, { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 120, 0 }, { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 180, 0 }, @@ -90,6 +93,10 @@ u16 ide_pio_cycle_time(ide_drive_t *drive, u8 pio) /* conservative "downgrade" for all pre-ATA2 drives */ if (pio < 3 && cycle < t->cycle) cycle = 0; /* use standard timing */ + + /* Use the standard timing for the CF specific modes too */ + if (pio > 4 && ata_id_is_cfa(id)) + cycle = 0; } return cycle ? cycle : t->cycle; @@ -161,7 +168,8 @@ int ide_timing_compute(ide_drive_t *drive, u8 speed, if (speed <= XFER_PIO_2) p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO]; - else if (speed <= XFER_PIO_5) + else if ((speed <= XFER_PIO_4) || + (speed == XFER_PIO_5 && !ata_id_is_cfa(id))) p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY]; else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2) p.cycle = id[ATA_ID_EIDE_DMA_MIN]; -- cgit v1.2.3