From 8ff84a2c99bc7f5f22d9d2b5365d821ce4f7a8f9 Mon Sep 17 00:00:00 2001 From: Wey-Yi Guy Date: Fri, 1 Apr 2011 16:29:52 -0700 Subject: iwlagn: more cleanup to remove unused reference More cleanup code, no functional changes Signed-off-by: Wey-Yi Guy --- drivers/net/wireless/iwlwifi/iwl-fh.h | 35 +++++++++++++++++------------------ 1 file changed, 17 insertions(+), 18 deletions(-) (limited to 'drivers/net/wireless/iwlwifi/iwl-fh.h') diff --git a/drivers/net/wireless/iwlwifi/iwl-fh.h b/drivers/net/wireless/iwlwifi/iwl-fh.h index 0f1052f80a5..b90924e890a 100644 --- a/drivers/net/wireless/iwlwifi/iwl-fh.h +++ b/drivers/net/wireless/iwlwifi/iwl-fh.h @@ -77,14 +77,14 @@ /** * Keep-Warm (KW) buffer base address. * - * Driver must allocate a 4KByte buffer that is used by 4965 for keeping the + * Driver must allocate a 4KByte buffer that is for keeping the * host DRAM powered on (via dummy accesses to DRAM) to maintain low-latency - * DRAM access when 4965 is Txing or Rxing. The dummy accesses prevent host + * DRAM access when doing Txing or Rxing. The dummy accesses prevent host * from going into a power-savings mode that would cause higher DRAM latency, * and possible data over/under-runs, before all Tx/Rx is complete. * * Driver loads FH_KW_MEM_ADDR_REG with the physical address (bits 35:4) - * of the buffer, which must be 4K aligned. Once this is set up, the 4965 + * of the buffer, which must be 4K aligned. Once this is set up, the device * automatically invokes keep-warm accesses when normal accesses might not * be sufficient to maintain fast DRAM response. * @@ -97,7 +97,7 @@ /** * TFD Circular Buffers Base (CBBC) addresses * - * 4965 has 16 base pointer registers, one for each of 16 host-DRAM-resident + * Device has 16 base pointer registers, one for each of 16 host-DRAM-resident * circular buffers (CBs/queues) containing Transmit Frame Descriptors (TFDs) * (see struct iwl_tfd_frame). These 16 pointer registers are offset by 0x04 * bytes from one another. Each TFD circular buffer in DRAM must be 256-byte @@ -116,16 +116,16 @@ /** * Rx SRAM Control and Status Registers (RSCSR) * - * These registers provide handshake between driver and 4965 for the Rx queue + * These registers provide handshake between driver and device for the Rx queue * (this queue handles *all* command responses, notifications, Rx data, etc. - * sent from 4965 uCode to host driver). Unlike Tx, there is only one Rx + * sent from uCode to host driver). Unlike Tx, there is only one Rx * queue, and only one Rx DMA/FIFO channel. Also unlike Tx, which can * concatenate up to 20 DRAM buffers to form a Tx frame, each Receive Buffer * Descriptor (RBD) points to only one Rx Buffer (RB); there is a 1:1 * mapping between RBDs and RBs. * * Driver must allocate host DRAM memory for the following, and set the - * physical address of each into 4965 registers: + * physical address of each into device registers: * * 1) Receive Buffer Descriptor (RBD) circular buffer (CB), typically with 256 * entries (although any power of 2, up to 4096, is selectable by driver). @@ -140,20 +140,20 @@ * Driver sets physical address [35:8] of base of RBD circular buffer * into FH_RSCSR_CHNL0_RBDCB_BASE_REG [27:0]. * - * 2) Rx status buffer, 8 bytes, in which 4965 indicates which Rx Buffers + * 2) Rx status buffer, 8 bytes, in which uCode indicates which Rx Buffers * (RBs) have been filled, via a "write pointer", actually the index of * the RB's corresponding RBD within the circular buffer. Driver sets * physical address [35:4] into FH_RSCSR_CHNL0_STTS_WPTR_REG [31:0]. * * Bit fields in lower dword of Rx status buffer (upper dword not used - * by driver; see struct iwl4965_shared, val0): + * by driver: * 31-12: Not used by driver * 11- 0: Index of last filled Rx buffer descriptor - * (4965 writes, driver reads this value) + * (device writes, driver reads this value) * - * As the driver prepares Receive Buffers (RBs) for 4965 to fill, driver must + * As the driver prepares Receive Buffers (RBs) for device to fill, driver must * enter pointers to these RBs into contiguous RBD circular buffer entries, - * and update the 4965's "write" index register, + * and update the device's "write" index register, * FH_RSCSR_CHNL0_RBDCB_WPTR_REG. * * This "write" index corresponds to the *next* RBD that the driver will make @@ -162,12 +162,12 @@ * RBs), should be 8 after preparing the first 8 RBs (for example), and must * wrap back to 0 at the end of the circular buffer (but don't wrap before * "read" index has advanced past 1! See below). - * NOTE: 4965 EXPECTS THE WRITE INDEX TO BE INCREMENTED IN MULTIPLES OF 8. + * NOTE: DEVICE EXPECTS THE WRITE INDEX TO BE INCREMENTED IN MULTIPLES OF 8. * - * As the 4965 fills RBs (referenced from contiguous RBDs within the circular + * As the device fills RBs (referenced from contiguous RBDs within the circular * buffer), it updates the Rx status buffer in host DRAM, 2) described above, * to tell the driver the index of the latest filled RBD. The driver must - * read this "read" index from DRAM after receiving an Rx interrupt from 4965. + * read this "read" index from DRAM after receiving an Rx interrupt from device * * The driver must also internally keep track of a third index, which is the * next RBD to process. When receiving an Rx interrupt, driver should process @@ -176,7 +176,7 @@ * driver may process the RB pointed to by RBD 0. Depending on volume of * traffic, there may be many RBs to process. * - * If read index == write index, 4965 thinks there is no room to put new data. + * If read index == write index, device thinks there is no room to put new data. * Due to this, the maximum number of filled RBs is 255, instead of 256. To * be safe, make sure that there is a gap of at least 2 RBDs between "write" * and "read" indexes; that is, make sure that there are no more than 254 @@ -303,7 +303,7 @@ /** * Transmit DMA Channel Control/Status Registers (TCSR) * - * 4965 has one configuration register for each of 8 Tx DMA/FIFO channels + * Device has one configuration register for each of 8 Tx DMA/FIFO channels * supported in hardware (don't confuse these with the 16 Tx queues in DRAM, * which feed the DMA/FIFO channels); config regs are separated by 0x20 bytes. * @@ -326,7 +326,6 @@ #define FH_TCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xE60) /* Find Control/Status reg for given Tx DMA/FIFO channel */ -#define FH49_TCSR_CHNL_NUM (7) #define FH50_TCSR_CHNL_NUM (8) /* TCSR: tx_config register values */ -- cgit v1.2.3