From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- drivers/scsi/cyberstorm.c | 377 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 377 insertions(+) create mode 100644 drivers/scsi/cyberstorm.c (limited to 'drivers/scsi/cyberstorm.c') diff --git a/drivers/scsi/cyberstorm.c b/drivers/scsi/cyberstorm.c new file mode 100644 index 00000000000..bdbca85d167 --- /dev/null +++ b/drivers/scsi/cyberstorm.c @@ -0,0 +1,377 @@ +/* cyberstorm.c: Driver for CyberStorm SCSI Controller. + * + * Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk) + * + * The CyberStorm SCSI driver is based on David S. Miller's ESP driver + * for the Sparc computers. + * + * This work was made possible by Phase5 who willingly (and most generously) + * supported me with hardware and all the information I needed. + */ + +/* TODO: + * + * 1) Figure out how to make a cleaner merge with the sparc driver with regard + * to the caches and the Sparc MMU mapping. + * 2) Make as few routines required outside the generic driver. A lot of the + * routines in this file used to be inline! + */ + +#include + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "scsi.h" +#include +#include "NCR53C9x.h" + +#include +#include +#include +#include + +#include + +/* The controller registers can be found in the Z2 config area at these + * offsets: + */ +#define CYBER_ESP_ADDR 0xf400 +#define CYBER_DMA_ADDR 0xf800 + + +/* The CyberStorm DMA interface */ +struct cyber_dma_registers { + volatile unsigned char dma_addr0; /* DMA address (MSB) [0x000] */ + unsigned char dmapad1[1]; + volatile unsigned char dma_addr1; /* DMA address [0x002] */ + unsigned char dmapad2[1]; + volatile unsigned char dma_addr2; /* DMA address [0x004] */ + unsigned char dmapad3[1]; + volatile unsigned char dma_addr3; /* DMA address (LSB) [0x006] */ + unsigned char dmapad4[0x3fb]; + volatile unsigned char cond_reg; /* DMA cond (ro) [0x402] */ +#define ctrl_reg cond_reg /* DMA control (wo) [0x402] */ +}; + +/* DMA control bits */ +#define CYBER_DMA_LED 0x80 /* HD led control 1 = on */ +#define CYBER_DMA_WRITE 0x40 /* DMA direction. 1 = write */ +#define CYBER_DMA_Z3 0x20 /* 16 (Z2) or 32 (CHIP/Z3) bit DMA transfer */ + +/* DMA status bits */ +#define CYBER_DMA_HNDL_INTR 0x80 /* DMA IRQ pending? */ + +/* The bits below appears to be Phase5 Debug bits only; they were not + * described by Phase5 so using them may seem a bit stupid... + */ +#define CYBER_HOST_ID 0x02 /* If set, host ID should be 7, otherwise + * it should be 6. + */ +#define CYBER_SLOW_CABLE 0x08 /* If *not* set, assume SLOW_CABLE */ + +static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count); +static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp); +static void dma_dump_state(struct NCR_ESP *esp); +static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length); +static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length); +static void dma_ints_off(struct NCR_ESP *esp); +static void dma_ints_on(struct NCR_ESP *esp); +static int dma_irq_p(struct NCR_ESP *esp); +static void dma_led_off(struct NCR_ESP *esp); +static void dma_led_on(struct NCR_ESP *esp); +static int dma_ports_p(struct NCR_ESP *esp); +static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write); + +static unsigned char ctrl_data = 0; /* Keep backup of the stuff written + * to ctrl_reg. Always write a copy + * to this register when writing to + * the hardware register! + */ + +static volatile unsigned char cmd_buffer[16]; + /* This is where all commands are put + * before they are transferred to the ESP chip + * via PIO. + */ + +/***************************************************************** Detection */ +int __init cyber_esp_detect(Scsi_Host_Template *tpnt) +{ + struct NCR_ESP *esp; + struct zorro_dev *z = NULL; + unsigned long address; + + while ((z = zorro_find_device(ZORRO_WILDCARD, z))) { + unsigned long board = z->resource.start; + if ((z->id == ZORRO_PROD_PHASE5_BLIZZARD_1220_CYBERSTORM || + z->id == ZORRO_PROD_PHASE5_BLIZZARD_1230_II_FASTLANE_Z3_CYBERSCSI_CYBERSTORM060) && + request_mem_region(board+CYBER_ESP_ADDR, + sizeof(struct ESP_regs), "NCR53C9x")) { + /* Figure out if this is a CyberStorm or really a + * Fastlane/Blizzard Mk II by looking at the board size. + * CyberStorm maps 64kB + * (ZORRO_PROD_PHASE5_BLIZZARD_1220_CYBERSTORM does anyway) + */ + if(z->resource.end-board != 0xffff) { + release_mem_region(board+CYBER_ESP_ADDR, + sizeof(struct ESP_regs)); + return 0; + } + esp = esp_allocate(tpnt, (void *)board+CYBER_ESP_ADDR); + + /* Do command transfer with programmed I/O */ + esp->do_pio_cmds = 1; + + /* Required functions */ + esp->dma_bytes_sent = &dma_bytes_sent; + esp->dma_can_transfer = &dma_can_transfer; + esp->dma_dump_state = &dma_dump_state; + esp->dma_init_read = &dma_init_read; + esp->dma_init_write = &dma_init_write; + esp->dma_ints_off = &dma_ints_off; + esp->dma_ints_on = &dma_ints_on; + esp->dma_irq_p = &dma_irq_p; + esp->dma_ports_p = &dma_ports_p; + esp->dma_setup = &dma_setup; + + /* Optional functions */ + esp->dma_barrier = 0; + esp->dma_drain = 0; + esp->dma_invalidate = 0; + esp->dma_irq_entry = 0; + esp->dma_irq_exit = 0; + esp->dma_led_on = &dma_led_on; + esp->dma_led_off = &dma_led_off; + esp->dma_poll = 0; + esp->dma_reset = 0; + + /* SCSI chip speed */ + esp->cfreq = 40000000; + + /* The DMA registers on the CyberStorm are mapped + * relative to the device (i.e. in the same Zorro + * I/O block). + */ + address = (unsigned long)ZTWO_VADDR(board); + esp->dregs = (void *)(address + CYBER_DMA_ADDR); + + /* ESP register base */ + esp->eregs = (struct ESP_regs *)(address + CYBER_ESP_ADDR); + + /* Set the command buffer */ + esp->esp_command = cmd_buffer; + esp->esp_command_dvma = virt_to_bus((void *)cmd_buffer); + + esp->irq = IRQ_AMIGA_PORTS; + request_irq(IRQ_AMIGA_PORTS, esp_intr, SA_SHIRQ, + "CyberStorm SCSI", esp->ehost); + /* Figure out our scsi ID on the bus */ + /* The DMA cond flag contains a hardcoded jumper bit + * which can be used to select host number 6 or 7. + * However, even though it may change, we use a hardcoded + * value of 7. + */ + esp->scsi_id = 7; + + /* We don't have a differential SCSI-bus. */ + esp->diff = 0; + + esp_initialize(esp); + + printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps, esps_in_use); + esps_running = esps_in_use; + return esps_in_use; + } + } + return 0; +} + +/************************************************************* DMA Functions */ +static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count) +{ + /* Since the CyberStorm DMA is fully dedicated to the ESP chip, + * the number of bytes sent (to the ESP chip) equals the number + * of bytes in the FIFO - there is no buffering in the DMA controller. + * XXXX Do I read this right? It is from host to ESP, right? + */ + return fifo_count; +} + +static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp) +{ + /* I don't think there's any limit on the CyberDMA. So we use what + * the ESP chip can handle (24 bit). + */ + unsigned long sz = sp->SCp.this_residual; + if(sz > 0x1000000) + sz = 0x1000000; + return sz; +} + +static void dma_dump_state(struct NCR_ESP *esp) +{ + ESPLOG(("esp%d: dma -- cond_reg<%02x>\n", + esp->esp_id, ((struct cyber_dma_registers *) + (esp->dregs))->cond_reg)); + ESPLOG(("intreq:<%04x>, intena:<%04x>\n", + custom.intreqr, custom.intenar)); +} + +static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length) +{ + struct cyber_dma_registers *dregs = + (struct cyber_dma_registers *) esp->dregs; + + cache_clear(addr, length); + + addr &= ~(1); + dregs->dma_addr0 = (addr >> 24) & 0xff; + dregs->dma_addr1 = (addr >> 16) & 0xff; + dregs->dma_addr2 = (addr >> 8) & 0xff; + dregs->dma_addr3 = (addr ) & 0xff; + ctrl_data &= ~(CYBER_DMA_WRITE); + + /* Check if physical address is outside Z2 space and of + * block length/block aligned in memory. If this is the + * case, enable 32 bit transfer. In all other cases, fall back + * to 16 bit transfer. + * Obviously 32 bit transfer should be enabled if the DMA address + * and length are 32 bit aligned. However, this leads to some + * strange behavior. Even 64 bit aligned addr/length fails. + * Until I've found a reason for this, 32 bit transfer is only + * used for full-block transfers (1kB). + * -jskov + */ +#if 0 + if((addr & 0x3fc) || length & 0x3ff || ((addr > 0x200000) && + (addr < 0xff0000))) + ctrl_data &= ~(CYBER_DMA_Z3); /* Z2, do 16 bit DMA */ + else + ctrl_data |= CYBER_DMA_Z3; /* CHIP/Z3, do 32 bit DMA */ +#else + ctrl_data &= ~(CYBER_DMA_Z3); /* Z2, do 16 bit DMA */ +#endif + dregs->ctrl_reg = ctrl_data; +} + +static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length) +{ + struct cyber_dma_registers *dregs = + (struct cyber_dma_registers *) esp->dregs; + + cache_push(addr, length); + + addr |= 1; + dregs->dma_addr0 = (addr >> 24) & 0xff; + dregs->dma_addr1 = (addr >> 16) & 0xff; + dregs->dma_addr2 = (addr >> 8) & 0xff; + dregs->dma_addr3 = (addr ) & 0xff; + ctrl_data |= CYBER_DMA_WRITE; + + /* See comment above */ +#if 0 + if((addr & 0x3fc) || length & 0x3ff || ((addr > 0x200000) && + (addr < 0xff0000))) + ctrl_data &= ~(CYBER_DMA_Z3); /* Z2, do 16 bit DMA */ + else + ctrl_data |= CYBER_DMA_Z3; /* CHIP/Z3, do 32 bit DMA */ +#else + ctrl_data &= ~(CYBER_DMA_Z3); /* Z2, do 16 bit DMA */ +#endif + dregs->ctrl_reg = ctrl_data; +} + +static void dma_ints_off(struct NCR_ESP *esp) +{ + disable_irq(esp->irq); +} + +static void dma_ints_on(struct NCR_ESP *esp) +{ + enable_irq(esp->irq); +} + +static int dma_irq_p(struct NCR_ESP *esp) +{ + /* It's important to check the DMA IRQ bit in the correct way! */ + return ((esp_read(esp->eregs->esp_status) & ESP_STAT_INTR) && + ((((struct cyber_dma_registers *)(esp->dregs))->cond_reg) & + CYBER_DMA_HNDL_INTR)); +} + +static void dma_led_off(struct NCR_ESP *esp) +{ + ctrl_data &= ~CYBER_DMA_LED; + ((struct cyber_dma_registers *)(esp->dregs))->ctrl_reg = ctrl_data; +} + +static void dma_led_on(struct NCR_ESP *esp) +{ + ctrl_data |= CYBER_DMA_LED; + ((struct cyber_dma_registers *)(esp->dregs))->ctrl_reg = ctrl_data; +} + +static int dma_ports_p(struct NCR_ESP *esp) +{ + return ((custom.intenar) & IF_PORTS); +} + +static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write) +{ + /* On the Sparc, DMA_ST_WRITE means "move data from device to memory" + * so when (write) is true, it actually means READ! + */ + if(write){ + dma_init_read(esp, addr, count); + } else { + dma_init_write(esp, addr, count); + } +} + +#define HOSTS_C + +int cyber_esp_release(struct Scsi_Host *instance) +{ +#ifdef MODULE + unsigned long address = (unsigned long)((struct NCR_ESP *)instance->hostdata)->edev; + + esp_deallocate((struct NCR_ESP *)instance->hostdata); + esp_release(); + release_mem_region(address, sizeof(struct ESP_regs)); + free_irq(IRQ_AMIGA_PORTS, esp_intr); +#endif + return 1; +} + + +static Scsi_Host_Template driver_template = { + .proc_name = "esp-cyberstorm", + .proc_info = esp_proc_info, + .name = "CyberStorm SCSI", + .detect = cyber_esp_detect, + .slave_alloc = esp_slave_alloc, + .slave_destroy = esp_slave_destroy, + .release = cyber_esp_release, + .queuecommand = esp_queue, + .eh_abort_handler = esp_abort, + .eh_bus_reset_handler = esp_reset, + .can_queue = 7, + .this_id = 7, + .sg_tablesize = SG_ALL, + .cmd_per_lun = 1, + .use_clustering = ENABLE_CLUSTERING +}; + + +#include "scsi_module.c" + +MODULE_LICENSE("GPL"); -- cgit v1.2.3