From 001dd84a92a25f8f2bad7d26df8bdb0362302c07 Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Fri, 11 Oct 2013 10:38:13 +0200 Subject: usb: musb: start musb on the udc side, too I have am335x-evm with one port running in OTG mode. Since commit fe4cb09 ("usb: musb: gadget: remove hcd initialization") the loaded gadget does non pop up on the host. All I see is |usb 4-5: new high-speed USB device number 52 using ehci-pci |usb 4-5: device descriptor read/64, error -110 Since a later commit 2cc65fe ("usb: musb: add musb_host_setup() and musb_host_cleanup()) the gadget shows up on the host again but only in OTG mode (because we have the host init code running). It does not work in device only mode. If running in OTG mode and the gadget is removed and added back (rmmod followed by modprobe of a gadget) then the same error is pops up on the host side. This patch ensures that the gadget side also executes musb_start() which puts the chip in "connect accept" mode. With this change the device works in OTG & device mode and the gadget can be added & removed multiple times. A device (if musb is in OTG mode acting as a host) is only recognized if it is attached during module load (musb_hdrc module). After the device unplugged and plugged again the host does not recognize it. We get a buch of errors if musb running in OTG mode, attached to a host and no gadget is loaded. Bah. This is one step forward. Host & device only mode should work. I will look at OTG later. I looked at this before commit fe4cb09 and OTG wasn't working there perfectly so I am not sure that it is a regression :) Cc: # v3.11 Cc: Daniel Mack Cc: Peter Korsgaard Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_core.c | 46 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 46 insertions(+) (limited to 'drivers/usb/musb/musb_core.c') diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 18e877ffe7b..cd70cc88617 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -921,6 +921,52 @@ static void musb_generic_disable(struct musb *musb) } +/* + * Program the HDRC to start (enable interrupts, dma, etc.). + */ +void musb_start(struct musb *musb) +{ + void __iomem *regs = musb->mregs; + u8 devctl = musb_readb(regs, MUSB_DEVCTL); + + dev_dbg(musb->controller, "<== devctl %02x\n", devctl); + + /* Set INT enable registers, enable interrupts */ + musb->intrtxe = musb->epmask; + musb_writew(regs, MUSB_INTRTXE, musb->intrtxe); + musb->intrrxe = musb->epmask & 0xfffe; + musb_writew(regs, MUSB_INTRRXE, musb->intrrxe); + musb_writeb(regs, MUSB_INTRUSBE, 0xf7); + + musb_writeb(regs, MUSB_TESTMODE, 0); + + /* put into basic highspeed mode and start session */ + musb_writeb(regs, MUSB_POWER, MUSB_POWER_ISOUPDATE + | MUSB_POWER_HSENAB + /* ENSUSPEND wedges tusb */ + /* | MUSB_POWER_ENSUSPEND */ + ); + + musb->is_active = 0; + devctl = musb_readb(regs, MUSB_DEVCTL); + devctl &= ~MUSB_DEVCTL_SESSION; + + /* session started after: + * (a) ID-grounded irq, host mode; + * (b) vbus present/connect IRQ, peripheral mode; + * (c) peripheral initiates, using SRP + */ + if (musb->port_mode != MUSB_PORT_MODE_HOST && + (devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) { + musb->is_active = 1; + } else { + devctl |= MUSB_DEVCTL_SESSION; + } + + musb_platform_enable(musb); + musb_writeb(regs, MUSB_DEVCTL, devctl); +} + /* * Make the HDRC stop (disable interrupts, etc.); * reversible by musb_start -- cgit v1.2.3