/* * pata_it8213.c - iTE Tech. Inc. IT8213 PATA driver * * The IT8213 is a very Intel ICH like device for timing purposes, having * a similar register layout and the same split clock arrangement. Cable * detection is different, and it does not have slave channels or all the * clutter of later ICH/SATA setups. */ #include #include #include #include #include #include #include #include #include #include #define DRV_NAME "pata_it8213" #define DRV_VERSION "0.0.3" /** * it8213_pre_reset - probe begin * @link: link * @deadline: deadline jiffies for the operation * * Filter out ports by the enable bits before doing the normal reset * and probe. */ static int it8213_pre_reset(struct ata_link *link, unsigned long deadline) { static const struct pci_bits it8213_enable_bits[] = { { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ }; struct ata_port *ap = link->ap; struct pci_dev *pdev = to_pci_dev(ap->host->dev); if (!pci_test_config_bits(pdev, &it8213_enable_bits[ap->port_no])) return -ENOENT; return ata_sff_prereset(link, deadline); } /** * it8213_cable_detect - check for 40/80 pin * @ap: Port * * Perform cable detection for the 8213 ATA interface. This is * different to the PIIX arrangement */ static int it8213_cable_detect(struct ata_port *ap) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u8 tmp; pci_read_config_byte(pdev, 0x42, &tmp); if (tmp & 2) /* The initial docs are incorrect */ return ATA_CBL_PATA40; return ATA_CBL_PATA80; } /** * it8213_set_piomode - Initialize host controller PATA PIO timings * @ap: Port whose timings we are configuring * @adev: Device whose timings we are configuring * * Set PIO mode for device, in host controller PCI config space. * * LOCKING: * None (inherited from caller). */ static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev) { unsigned int pio = adev->pio_mode - XFER_PIO_0; struct pci_dev *dev = to_pci_dev(ap->host->dev); unsigned int master_port = ap->port_no ? 0x42 : 0x40; u16 master_data; int control = 0; /* * See Intel Document 298600-004 for the timing programing rules * for PIIX/ICH. The 8213 is a clone so very similar */ static const /* ISP RTC */ u8 timings[][2] = { { 0, 0 }, { 0, 0 }, { 1, 0 }, { 2, 1 }, { 2, 3 }, }; if (pio > 1) control |= 1; /* TIME */ if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */ control |= 2; /* IE */ /* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */ if (adev->class != ATA_DEV_ATA) control |= 4; /* PPE */ pci_read_config_word(dev, master_port, &master_data); /* Set PPE, IE, and TIME as appropriate */ if (adev->devno == 0) { master_data &= 0xCCF0; master_data |= control; master_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); } else { u8 slave_data; master_data &= 0xFF0F; master_data |= (control << 4); /* Slave timing in separate register */ pci_read_config_byte(dev, 0x44, &slave_data); slave_data &= 0xF0; slave_data |= (timings[pio][0] << 2) | timings[pio][1]; pci_write_config_byte(dev, 0x44, slave_data); } master_data |= 0x4000; /* Ensure SITRE is set */ pci_write_config_word(dev, master_port, master_data); } /** * it8213_set_dmamode - Initialize host controller PATA DMA timings * @ap: Port whose timings we are configuring * @adev: Device to program * * Set UDMA/MWDMA mode for device, in host controller PCI config space. * This device is basically an ICH alike. * * LOCKING: * None (inherited from caller). */ static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev) { struct pci_dev *dev = to_pci_dev(ap->host->dev); u16 master_data; u8 speed = adev->dma_mode; int devid = adev->devno; u8 udma_enable; static const /* ISP RTC */ u8 timings[][2] = { { 0, 0 }, { 0, 0 }, { 1, 0 }, { 2, 1 }, { 2, 3 }, }; pci_read_config_word(dev, 0x40, &master_data); pci_read_config_byte(dev, 0x48, &udma_enable); if (speed >= XFER_UDMA_0) { unsigned int udma = adev->dma_mode - XFER_UDMA_0; u16 udma_timing; u16 ideconf; int u_clock, u_speed; /* Clocks follow the PIIX style */ u_speed = min(2 - (udma & 1), udma); if (udma > 4) u_clock = 0x1000; /* 100Mhz */ else if (udma > 2) u_clock = 1; /* 66Mhz */ else u_clock = 0; /* 33Mhz */ udma_enable |= (1 << devid); /* Load the UDMA cycle time */ pci_read_config_word(dev, 0x4A, &udma_timing); udma_timing &= ~(3 << (4 * devid)); udma_timing |= u_speed << (4 * devid); pci_write_config_word(dev, 0x4A, udma_timing); /* Load the clock selection */ pci_read_config_word(dev, 0x54, &ideconf); ideconf &= ~(0x1001 << devid); ideconf |= u_clock << devid; pci_write_config_word(dev, 0x54, ideconf); } else { /* * MWDMA is driven by the PIO timings. We must also enable * IORDY unconditionally along with TIME1. PPE has already * been set when the PIO timing was set. */ unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; unsigned int control; u8 slave_data; static const unsigned int needed_pio[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 }; int pio = needed_pio[mwdma] - XFER_PIO_0; control = 3; /* IORDY|TIME1 */ /* If the drive MWDMA is faster than it can do PIO then we must force PIO into PIO0 */ if (adev->pio_mode < needed_pio[mwdma]) /* Enable DMA timing only */ control |= 8; /* PIO cycles in PIO0 */ if (devid) { /* Slave */ master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */ master_data |= control << 4; pci_read_config_byte(dev, 0x44, &slave_data); slave_data &= 0xF0; /* Load the matching timing */ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); pci_write_config_byte(dev, 0x44, slave_data); } else { /* Master */ master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY and master timing bits */ master_data |= control; master_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); } udma_enable &= ~(1 << devid); pci_write_config_word(dev, 0x40, master_data); } pci_write_config_byte(dev, 0x48, udma_enable); } static struct scsi_host_template it8213_sht = { ATA_BMDMA_SHT(DRV_NAME), }; static struct ata_port_operations it8213_ops = { .inherits = &ata_bmdma_port_ops, .cable_detect = it8213_cable_detect, .set_piomode = it8213_set_piomode, .set_dmamode = it8213_set_dmamode, .prereset = it8213_pre_reset, }; /** * it8213_init_one - Register 8213 ATA PCI device with kernel services * @pdev: PCI device to register * @ent: Entry in it8213_pci_tbl matching with @pdev * * Called from kernel PCI layer. * * LOCKING: * Inherited from PCI layer (may sleep). * * RETURNS: * Zero on success, or -ERRNO value. */ static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) { static const struct ata_port_info info = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, .mwdma_mask = ATA_MWDMA12_ONLY, .udma_mask = ATA_UDMA6, .port_ops = &it8213_ops, }; /* Current IT8213 stuff is single port */ const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info }; ata_print_version_once(&pdev->dev, DRV_VERSION); return ata_pci_bmdma_init_one(pdev, ppi, &it8213_sht, NULL, 0); } static const struct pci_device_id it8213_pci_tbl[] = { { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8213), }, { } /* terminate list */ }; static struct pci_driver it8213_pci_driver = { .name = DRV_NAME, .id_table = it8213_pci_tbl, .probe = it8213_init_one, .remove = ata_pci_remove_one, #ifdef CONFIG_PM .suspend = ata_pci_device_suspend, .resume = ata_pci_device_resume, #endif }; static int __init it8213_init(void) { return pci_register_driver(&it8213_pci_driver); } static void __exit it8213_exit(void) { pci_unregister_driver(&it8213_pci_driver); } module_init(it8213_init); module_exit(it8213_exit); MODULE_AUTHOR("Alan Cox"); MODULE_DESCRIPTION("SCSI low-level driver for the ITE 8213"); MODULE_LICENSE("GPL"); MODULE_DEVICE_TABLE(pci, it8213_pci_tbl); MODULE_VERSION(DRV_VERSION);