/* * Copyright © 2009 - Maxim Levitsky * driver for Ricoh xD readers * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #include #include #include #include #include /* nand interface + ecc byte write/read does one cycle on nand data lines. dword write/read does 4 cycles if R852_CTL_ECC_ACCESS is set in R852_CTL, then dword read reads results of ecc correction, if DMA read was done before. If write was done two dword reads read generated ecc checksums */ #define R852_DATALINE 0x00 /* control register */ #define R852_CTL 0x04 #define R852_CTL_COMMAND 0x01 /* send command (#CLE)*/ #define R852_CTL_DATA 0x02 /* read/write data (#ALE)*/ #define R852_CTL_ON 0x04 /* only seem to controls the hd led, */ /* but has to be set on start...*/ #define R852_CTL_RESET 0x08 /* unknown, set only on start once*/ #define R852_CTL_CARDENABLE 0x10 /* probably (#CE) - always set*/ #define R852_CTL_ECC_ENABLE 0x20 /* enable ecc engine */ #define R852_CTL_ECC_ACCESS 0x40 /* read/write ecc via reg #0*/ #define R852_CTL_WRITE 0x80 /* set when performing writes (#WP) */ /* card detection status */ #define R852_CARD_STA 0x05 #define R852_CARD_STA_CD 0x01 /* state of #CD line, same as 0x04 */ #define R852_CARD_STA_RO 0x02 /* card is readonly */ #define R852_CARD_STA_PRESENT 0x04 /* card is present (#CD) */ #define R852_CARD_STA_ABSENT 0x08 /* card is absent */ #define R852_CARD_STA_BUSY 0x80 /* card is busy - (#R/B) */ /* card detection irq status & enable*/ #define R852_CARD_IRQ_STA 0x06 /* IRQ status */ #define R852_CARD_IRQ_ENABLE 0x07 /* IRQ enable */ #define R852_CARD_IRQ_CD 0x01 /* fire when #CD lights, same as 0x04*/ #define R852_CARD_IRQ_REMOVE 0x04 /* detect card removal */ #define R852_CARD_IRQ_INSERT 0x08 /* detect card insert */ #define R852_CARD_IRQ_UNK1 0x10 /* unknown */ #define R852_CARD_IRQ_GENABLE 0x80 /* general enable */ #define R852_CARD_IRQ_MASK 0x1D /* hardware enable */ #define R852_HW 0x08 #define R852_HW_ENABLED 0x01 /* hw enabled */ #define R852_HW_UNKNOWN 0x80 /* dma capabilities */ #define R852_DMA_CAP 0x09 #define R852_SMBIT 0x20 /* if set with bit #6 or bit #7, then */ /* hw is smartmedia */ #define R852_DMA1 0x40 /* if set w/bit #7, dma is supported */ #define R852_DMA2 0x80 /* if set w/bit #6, dma is supported */ /* physical DMA address - 32 bit value*/ #define R852_DMA_ADDR 0x0C /* dma settings */ #define R852_DMA_SETTINGS 0x10 #define R852_DMA_MEMORY 0x01 /* (memory <-> internal hw buffer) */ #define R852_DMA_READ 0x02 /* 0 = write, 1 = read */ #define R852_DMA_INTERNAL 0x04 /* (internal hw buffer <-> card) */ /* dma IRQ status */ #define R852_DMA_IRQ_STA 0x14 /* dma IRQ enable */ #define R852_DMA_IRQ_ENABLE 0x18 #define R852_DMA_IRQ_MEMORY 0x01 /* (memory <-> internal hw buffer) */ #define R852_DMA_IRQ_ERROR 0x02 /* error did happen */ #define R852_DMA_IRQ_INTERNAL 0x04 /* (internal hw buffer <-> card) */ #define R852_DMA_IRQ_MASK 0x07 /* mask of all IRQ bits */ /* ECC syndrome format - read from reg #0 will return two copies of these for each half of the page. first byte is error byte location, and second, bit location + flags */ #define R852_ECC_ERR_BIT_MSK 0x07 /* error bit location */ #define R852_ECC_CORRECT 0x10 /* no errors - (guessed) */ #define R852_ECC_CORRECTABLE 0x20 /* correctable error exist */ #define R852_ECC_FAIL 0x40 /* non correctable error detected */ #define R852_DMA_LEN 512 #define DMA_INTERNAL 0 #define DMA_MEMORY 1 struct r852_device { void __iomem *mmio; /* mmio */ struct mtd_info *mtd; /* mtd backpointer */ struct nand_chip *chip; /* nand chip backpointer */ struct pci_dev *pci_dev; /* pci backpointer */ /* dma area */ dma_addr_t phys_dma_addr; /* bus address of buffer*/ struct completion dma_done; /* data transfer done */ dma_addr_t phys_bounce_buffer; /* bus address of bounce buffer */ uint8_t *bounce_buffer; /* virtual address of bounce buffer */ int dma_dir; /* 1 = read, 0 = write */ int dma_stage; /* 0 - idle, 1 - first step, 2 - second step */ int dma_state; /* 0 = internal, 1 = memory */ int dma_error; /* dma errors */ int dma_usable; /* is it possible to use dma */ /* card status area */ struct delayed_work card_detect_work; struct workqueue_struct *card_workqueue; int card_registred; /* card registered with mtd */ int card_detected; /* card detected in slot */ int card_unstable; /* whenever the card is inserted, is not known yet */ int readonly; /* card is readonly */ int sm; /* Is card smartmedia */ /* interrupt handling */ spinlock_t irqlock; /* IRQ protecting lock */ int irq; /* irq num */ /* misc */ void *tmp_buffer; /* temporary buffer */ uint8_t ctlreg; /* cached contents of control reg */ }; #define DRV_NAME "r852" #define dbg(format, ...) \ if (debug) \ printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__) #define dbg_verbose(format, ...) \ if (debug > 1) \ printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__) #define message(format, ...) \ printk(KERN_INFO DRV_NAME ": " format "\n", ## __VA_ARGS__)