/* * Adaptec 274x/284x/294x device driver firmware for Linux and FreeBSD. * * Copyright (c) 1994-1999 Justin Gibbs. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions, and the following disclaimer, * without modification, immediately at the beginning of the file. * 2. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * Where this Software is combined with software released under the terms of * the GNU General Public License (GPL) and the terms of the GPL would require the * combined work to also be released under the terms of the GPL, the terms * and conditions of this License will apply in addition to those of the * GPL with the exception of any terms or conditions of this License that * conflict with, or are expressly prohibited by, the GPL. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * $Id: aic7xxx.seq,v 1.77 1998/06/28 02:58:57 gibbs Exp $ */ #include "aic7xxx.reg" #include "scsi_message.h" /* * A few words on the waiting SCB list: * After starting the selection hardware, we check for reconnecting targets * as well as for our selection to complete just in case the reselection wins * bus arbitration. The problem with this is that we must keep track of the * SCB that we've already pulled from the QINFIFO and started the selection * on just in case the reselection wins so that we can retry the selection at * a later time. This problem cannot be resolved by holding a single entry * in scratch ram since a reconnecting target can request sense and this will * create yet another SCB waiting for selection. The solution used here is to * use byte 27 of the SCB as a pseudo-next pointer and to thread a list * of SCBs that are awaiting selection. Since 0-0xfe are valid SCB indexes, * SCB_LIST_NULL is 0xff which is out of range. An entry is also added to * this list every time a request sense occurs or after completing a non-tagged * command for which a second SCB has been queued. The sequencer will * automatically consume the entries. */ reset: clr SCSISIGO; /* De-assert BSY */ and SXFRCTL1, ~BITBUCKET; /* Always allow reselection */ mvi SCSISEQ, ENRSELI|ENAUTOATNP; if ((p->features & AHC_CMD_CHAN) != 0) { /* Ensure that no DMA operations are in progress */ clr CCSGCTL; clr CCSCBCTL; } call clear_target_state; poll_for_work: and SXFRCTL0, ~SPIOEN; if ((p->features & AHC_QUEUE_REGS) == 0) { mov A, QINPOS; } poll_for_work_loop: if ((p->features & AHC_QUEUE_REGS) == 0) { and SEQCTL, ~PAUSEDIS; } test SSTAT0, SELDO|SELDI jnz selection; test SCSISEQ, ENSELO jnz poll_for_work; if ((p->features & AHC_TWIN) != 0) { /* * Twin channel devices cannot handle things like SELTO * interrupts on the "background" channel. So, if we * are selecting, keep polling the current channel util * either a selection or reselection occurs. */ xor SBLKCTL,SELBUSB; /* Toggle to the other bus */ test SSTAT0, SELDO|SELDI jnz selection; test SCSISEQ, ENSELO jnz poll_for_work; xor SBLKCTL,SELBUSB; /* Toggle back */ } cmp WAITING_SCBH,SCB_LIST_NULL jne start_waiting; test_queue: /* Has the driver posted any work for us? */ if ((p->features & AHC_QUEUE_REGS) != 0) { test QOFF_CTLSTA, SCB_AVAIL jz poll_for_work_loop; mov NONE, SNSCB_QOFF; inc QINPOS; } else { or SEQCTL, PAUSEDIS; cmp KERNEL_QINPOS, A je poll_for_work_loop; inc QINPOS; and SEQCTL, ~PAUSEDIS; } /* * We have at least one queued SCB now and we don't have any * SCBs in the list of SCBs awaiting selection. If we have * any SCBs available for use, pull the tag from the QINFIFO * and get to work on it. */ if ((p->flags & AHC_PAGESCBS) != 0) { mov ALLZEROS call get_free_or_disc_scb; } dequeue_scb: add A, -1, QINPOS; mvi QINFIFO_OFFSET call fetch_byte; if ((p->flags & AHC_PAGESCBS) == 0) { /* In the non-paging case, the SCBID == hardware SCB index */ mov SCBPTR, RETURN_2; } dma_queued_scb: /* * DMA the SCB from host ram into the current SCB location. */ mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; mov RETURN_2 call dma_scb; /* * Preset the residual fields in case we never go through a data phase. * This isn't done by the host so we can avoid a DMA to clear these * fields for the normal case of I/O that completes without underrun * or overrun conditions. */ if ((p->features & AHC_CMD_CHAN) != 0) { bmov SCB_RESID_DCNT, SCB_DATACNT, 3; } else { mov SCB_RESID_DCNT[0],SCB_DATACNT[0]; mov SCB_RESID_DCNT[1],SCB_DATACNT[1]; mov SCB_RESID_DCNT[2],SCB_DATACNT[2]; } mov SCB_RESID_SGCNT, SCB_SGCOUNT; start_scb: /* * Place us on the waiting list in case our selection * doesn't win during bus arbitration. */ mov SCB_NEXT,WAITING_SCBH; mov WAITING_SCBH, SCBPTR; start_waiting: /* * Pull the first entry off of the waiting SCB list. */ mov SCBPTR, WAITING_SCBH; call start_selection; jmp poll_for_work; start_selection: if ((p->features & AHC_TWIN) != 0) { and SINDEX,~SELBUSB,SBLKCTL;/* Clear channel select bit */ and A,SELBUSB,SCB_TCL; /* Get new channel bit */ or SINDEX,A; mov SBLKCTL,SINDEX; /* select channel */ } initialize_scsiid: if ((p->features & AHC_ULTRA2) != 0) { and A, TID, SCB_TCL; /* Get target ID */ and SCSIID_ULTRA2, OID; /* Clear old target */ or SCSIID_ULTRA2, A; } else { and A, TID, SCB_TCL; /* Get target ID */ and SCSIID, OID; /* Clear old target */ or SCSIID, A; } mov SCSIDATL, ALLZEROS; /* clear out the latched */ /* data register, this */ /* fixes a bug on some */ /* controllers where the */ /* last byte written to */ /* this register can leak */ /* onto the data bus at */ /* bad times, such as during */ /* selection timeouts */ mvi SCSISEQ, ENSELO|ENAUTOATNO|ENRSELI|ENAUTOATNP ret; /* * Initialize Ultra mode setting and clear the SCSI channel. * SINDEX should contain any additional bit's the client wants * set in SXFRCTL0. */ initialize_channel: or SXFRCTL0, CLRSTCNT|CLRCHN, SINDEX; if ((p->features & AHC_ULTRA) != 0) { ultra: mvi SINDEX, ULTRA_ENB+1; test SAVED_TCL, 0x80 jnz ultra_2; /* Target ID > 7 */ dec SINDEX; ultra_2: mov FUNCTION1,SAVED_TCL; mov A,FUNCTION1; test SINDIR, A jz ndx_dtr; or SXFRCTL0, FAST20; } /* * Initialize SCSIRATE with the appropriate value for this target. * The SCSIRATE settings for each target are stored in an array * based at TARG_SCSIRATE. */ ndx_dtr: shr A,4,SAVED_TCL; if ((p->features & AHC_TWIN) != 0) { test SBLKCTL,SELBUSB jz ndx_dtr_2; or SAVED_TCL, SELBUSB; or A,0x08; /* Channel B entries add 8 */ ndx_dtr_2: } if ((p->features & AHC_ULTRA2) != 0) { add SINDEX, TARG_OFFSET, A; mov SCSIOFFSET, SINDIR; } add SINDEX,TARG_SCSIRATE,A; mov SCSIRATE,SINDIR ret; selection: test SSTAT0,SELDO jnz select_out; /* * Reselection has been initiated by a target. Make a note that we've been * reselected, but haven't seen an IDENTIFY message from the target yet. */ initiator_reselect: mvi CLRSINT0, CLRSELDI; /* XXX test for and handle ONE BIT condition */ and SAVED_TCL, SELID_MASK, SELID; mvi CLRSINT1,CLRBUSFREE; or SIMODE1, ENBUSFREE; /* * We aren't expecting a * bus free, so interrupt * the kernel driver if it * happens. */ mvi SPIOEN call initialize_channel; mvi MSG_OUT, MSG_NOOP; /* No message to send */ jmp ITloop; /* * After the selection, remove this SCB from the "waiting SCB" * list. This is achieved by simply moving our "next" pointer into * WAITING_SCBH. Our next pointer will be set to null the next time this * SCB is used, so don't bother with it now. */ select_out: /* Turn off the selection hardware */ mvi SCSISEQ, ENRSELI|ENAUTOATNP; /* * ATN on parity errors * for "in" phases */ mvi CLRSINT0, CLRSELDO; mov SCBPTR, WAITING_SCBH; mov WAITING_SCBH,SCB_NEXT; mov SAVED_TCL, SCB_TCL; mvi CLRSINT1,CLRBUSFREE; or SIMODE1, ENBUSFREE; /* * We aren't expecting a * bus free, so interrupt * the kernel driver if it * happens. */ mvi SPIOEN call initialize_channel; /* * As soon as we get a successful selection, the target should go * into the message out phase since we have ATN asserted. */ mvi MSG_OUT, MSG_IDENTIFYFLAG; or SEQ_FLAGS, IDENTIFY_SEEN; /* * Main loop for information transfer phases. Wait for the target * to assert REQ before checking MSG, C/D and I/O for the bus phase. */ ITloop: call phase_lock; mov A, LASTPHASE; test A, ~P_DATAIN jz p_data; cmp A,P_COMMAND je p_command; cmp A,P_MESGOUT je p_mesgout; cmp A,P_STATUS je p_status; cmp A,P_MESGIN je p_mesgin; mvi INTSTAT,BAD_PHASE; /* unknown phase - signal driver */ jmp ITloop; /* Try reading the bus again. */ await_busfree: and SIMODE1, ~ENBUSFREE; call clear_target_state; mov NONE, SCSIDATL; /* Ack the last byte */ and SXFRCTL0, ~SPIOEN; test SSTAT1,REQINIT|BUSFREE jz .; test SSTAT1, BUSFREE jnz poll_for_work; mvi INTSTAT, BAD_PHASE; clear_target_state: /* * We assume that the kernel driver may reset us * at any time, even in the middle of a DMA, so * clear DFCNTRL too. */ clr DFCNTRL; /* * We don't know the target we will connect to, * so default to narrow transfers to avoid * parity problems. */ if ((p->features & AHC_ULTRA2) != 0) { bmov SCSIRATE, ALLZEROS, 2; } else { clr SCSIRATE; and SXFRCTL0, ~(FAST20); } mvi LASTPHASE, P_BUSFREE; /* clear target specific flags */ clr SEQ_FLAGS ret; data_phase_reinit: /* * If we re-enter the data phase after going through another phase, the * STCNT may have been cleared, so restore it from the residual field. * On Ultra2, we have to put it into the HCNT field because we have to * drop the data down into the shadow layer via the preload ability. */ if ((p->features & AHC_ULTRA2) != 0) { bmov HADDR, SHADDR, 4; bmov HCNT, SCB_RESID_DCNT, 3; } if ((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) { bmov STCNT, SCB_RESID_DCNT, 3; } if ((p->features & AHC_CMD_CHAN) == 0) { mvi DINDEX, STCNT; mvi SCB_RESID_DCNT call bcopy_3; } jmp data_phase_loop; p_data: if ((p->features & AHC_ULTRA2) != 0) { mvi DMAPARAMS, PRELOADEN|SCSIEN|HDMAEN; } else { mvi DMAPARAMS, WIDEODD|SCSIEN|SDMAEN|HDMAEN|FIFORESET; } test LASTPHASE, IOI jnz . + 2; or DMAPARAMS, DIRECTION; call assert; /* * Ensure entering a data * phase is okay - seen identify, etc. */ if ((p->features & AHC_CMD_CHAN) != 0) { mvi CCSGADDR, CCSGADDR_MAX; } test SEQ_FLAGS, DPHASE jnz data_phase_reinit; or SEQ_FLAGS, DPHASE; /* we've seen a data phase */ /* * Initialize the DMA address and counter from the SCB. * Also set SG_COUNT and SG_NEXT in memory since we cannot * modify the values in the SCB itself until we see a * save data pointers message. */ if ((p->features & AHC_CMD_CHAN) != 0) { bmov HADDR, SCB_DATAPTR, 7; bmov SG_COUNT, SCB_SGCOUNT, 5; if ((p->features & AHC_ULTRA2) == 0) { bmov STCNT, HCNT, 3; } } else { mvi DINDEX, HADDR; mvi SCB_DATAPTR call bcopy_7; call set_stcnt_from_hcnt; mvi DINDEX, SG_COUNT; mvi SCB_SGCOUNT call bcopy_5; } data_phase_loop: /* Guard against overruns */ test SG_COUNT, 0xff jnz data_phase_inbounds; /* * Turn on 'Bit Bucket' mode, set the transfer count to * 16meg and let the target run until it changes phase. * When the transfer completes, notify the host that we * had an overrun. */ or SXFRCTL1,BITBUCKET; and DMAPARAMS, ~(HDMAEN|SDMAEN); if ((p->features & AHC_ULTRA2) != 0) { bmov HCNT, ALLONES, 3; } if ((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) { bmov STCNT, ALLONES, 3; } if ((p->features & AHC_CMD_CHAN) == 0) { mvi STCNT[0], 0xFF; mvi STCNT[1], 0xFF; mvi STCNT[2], 0xFF; } data_phase_inbounds: /* If we are the last SG block, tell the hardware. */ if ((p->features & AHC_ULTRA2) != 0) { shl A, 2, SG_COUNT; cmp SG_COUNT,0x01 jne data_phase_wideodd; or A, LAST_SEG; } else { cmp SG_COUNT,0x01 jne data_phase_wideodd; and DMAPARAMS, ~WIDEODD; } data_phase_wideodd: if ((p->features & AHC_ULTRA2) != 0) { mov SG_CACHEPTR, A; mov DFCNTRL, DMAPARAMS; /* start the operation */ test SXFRCTL1, BITBUCKET jnz data_phase_overrun; u2_preload_wait: test SSTAT1, PHASEMIS jnz u2_phasemis; test DFSTATUS, PRELOAD_AVAIL jz u2_preload_wait; } else { mov DMAPARAMS call dma; data_phase_dma_done: /* Go tell the host about any overruns */ test SXFRCTL1,BITBUCKET jnz data_phase_overrun; /* Exit if we had an underrun. dma clears SINDEX in this case. */ test SINDEX,0xff jz data_phase_finish; } /* * Advance the scatter-gather pointers */ sg_advance: if ((p->features & AHC_ULTRA2) != 0) { cmp SG_COUNT, 0x01 je u2_data_phase_finish; } else { dec SG_COUNT; test SG_COUNT, 0xff jz data_phase_finish; } if ((p->features & AHC_CMD_CHAN) != 0) { /* * Do we have any prefetch left??? */ cmp CCSGADDR, CCSGADDR_MAX jne prefetch_avail; /* * Fetch MIN(CCSGADDR_MAX, (SG_COUNT * 8)) bytes. */ add A, -(CCSGRAM_MAXSEGS + 1), SG_COUNT; mvi A, CCSGADDR_MAX; jc . + 2; shl A, 3, SG_COUNT; mov CCHCNT, A; bmov CCHADDR, SG_NEXT, 4; mvi CCSGCTL, CCSGEN|CCSGRESET; test CCSGCTL, CCSGDONE jz .; and CCSGCTL, ~CCSGEN; test CCSGCTL, CCSGEN jnz .; mvi CCSGCTL, CCSGRESET; prefetch_avail: bmov HADDR, CCSGRAM, 8; if ((p->features & AHC_ULTRA2) == 0) { bmov STCNT, HCNT, 3; } else { dec SG_COUNT; } } else { mvi DINDEX, HADDR; mvi SG_NEXT call bcopy_4; mvi HCNT[0],SG_SIZEOF; clr HCNT[1]; clr HCNT[2]; or DFCNTRL, HDMAEN|DIRECTION|FIFORESET; call dma_finish; /* * Copy data from FIFO into SCB data pointer and data count. * This assumes that the SG segments are of the form: * struct ahc_dma_seg { * u_int32_t addr; four bytes, little-endian order * u_int32_t len; four bytes, little endian order * }; */ mvi DINDEX, HADDR; call dfdat_in_7; call set_stcnt_from_hcnt; } /* Advance the SG pointer */ clr A; /* add sizeof(struct scatter) */ add SG_NEXT[0],SG_SIZEOF; adc SG_NEXT[1],A; if ((p->features & AHC_ULTRA2) != 0) { jmp data_phase_loop; } else { test SSTAT1, REQINIT jz .; test SSTAT1,PHASEMIS jz data_phase_loop; } /* * We've loaded all of our segments into the preload layer. Now, we simply * have to wait for it to finish or for us to get a phasemis. And, since * we'll get a phasemis if we do finish, all we really need to do is wait * for a phasemis then check if we did actually complete all the segments. */ if ((p->features & AHC_ULTRA2) != 0) { u2_data_phase_finish: test SSTAT1, PHASEMIS jnz u2_phasemis; test SG_CACHEPTR, LAST_SEG_DONE jz u2_data_phase_finish; clr SG_COUNT; test SSTAT1, REQINIT jz .; test SSTAT1, PHASEMIS jz data_phase_loop; u2_phasemis: call ultra2_dmafinish; test SG_CACHEPTR, LAST_SEG_DONE jnz data_phase_finish; test SSTAT2, SHVALID jnz u2_fixup_residual; mvi INTSTAT, SEQ_SG_FIXUP; jmp data_phase_finish; u2_fixup_residual: shr ARG_1, 2, SG_CACHEPTR; u2_phasemis_loop: and A, 0x3f, SG_COUNT; cmp ARG_1, A je data_phase_finish; /* * Subtract SG_SIZEOF from the SG_NEXT pointer and add 1 to the SG_COUNT */ clr A; add SG_NEXT[0], -SG_SIZEOF; adc SG_NEXT[1], 0xff; inc SG_COUNT; jmp u2_phasemis_loop; } data_phase_finish: /* * After a DMA finishes, save the SG and STCNT residuals back into the SCB * We use STCNT instead of HCNT, since it's a reflection of how many bytes * were transferred on the SCSI (as opposed to the host) bus. */ if ((p->features & AHC_CMD_CHAN) != 0) { bmov SCB_RESID_DCNT, STCNT, 3; mov SCB_RESID_SGCNT, SG_COUNT; if ((p->features & AHC_ULTRA2) != 0) { or SXFRCTL0, CLRSTCNT|CLRCHN; } } else { mov SCB_RESID_DCNT[0],STCNT[0]; mov SCB_RESID_DCNT[1],STCNT[1]; mov SCB_RESID_DCNT[2],STCNT[2]; mov SCB_RESID_SGCNT, SG_COUNT; } jmp ITloop; data_phase_overrun: /* * Turn off BITBUCKET mode and notify the host */ if ((p->features & AHC_ULTRA2) != 0) { /* * Wait for the target to quit transferring data on the SCSI bus */ test SSTAT1, PHASEMIS jz .; call ultra2_dmafinish; } and SXFRCTL1, ~BITBUCKET; mvi INTSTAT,DATA_OVERRUN; jmp ITloop; /* * Actually turn off the DMA hardware, save our current position into the * proper residual variables, wait for the next REQ signal, then jump to * the ITloop. Jumping to the ITloop ensures that if we happen to get * brought into the data phase again (or are still in it after our last * segment) that we will properly signal an overrun to the kernel. */ if ((p->features & AHC_ULTRA2) != 0) { ultra2_dmafinish: test DFCNTRL, DIRECTION jnz ultra2_dmahalt; and DFCNTRL, ~SCSIEN; test DFCNTRL, SCSIEN jnz .; if ((p->bugs & AHC_BUG_AUTOFLUSH) != 0) { or DFCNTRL, FIFOFLUSH; } ultra2_dmafifoflush: if ((p->bugs & AHC_BUG_AUTOFLUSH) != 0) { /* * hardware bug alert! This needless set of jumps * works around a glitch in the silicon. When the * PCI DMA fifo goes empty, but there is still SCSI * data to be flushed into the PCI DMA fifo (and from * there on into main memory), the FIFOEMP bit will * come on between the time when the PCI DMA buffer * went empty and the next bit of data is copied from * the SCSI fifo into the PCI fifo. It should only * come on when both FIFOs (meaning the entire FIFO * chain) are empty. Since it can take up to 4 cycles * for new data to be copied from the SCSI fifo into * the PCI fifo, testing for FIFOEMP status for 4 * extra times gives the needed time for any * remaining SCSI fifo data to be put in the PCI fifo * before we declare it *truly* empty. */ test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; } test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; test DFSTATUS, MREQPEND jnz .; ultra2_dmahalt: and DFCNTRL, ~(HDMAEN|SCSIEN); test DFCNTRL, (HDMAEN|SCSIEN) jnz .; ret; } /* * Command phase. Set up the DMA registers and let 'er rip. */ p_command: call assert; /* * Load HADDR and HCNT. */ if ((p->features & AHC_CMD_CHAN) != 0) { bmov HADDR, SCB_CMDPTR, 5; bmov HCNT[1], ALLZEROS, 2; if ((p->features & AHC_ULTRA2) == 0) { bmov STCNT, HCNT, 3; } } else { mvi DINDEX, HADDR; mvi SCB_CMDPTR call bcopy_5; clr HCNT[1]; clr HCNT[2]; call set_stcnt_from_hcnt; } if ((p->features & AHC_ULTRA2) == 0) { mvi (SCSIEN|SDMAEN|HDMAEN|DIRECTION|FIFORESET) call dma; } else { mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN|DIRECTION); test SSTAT0, SDONE jnz .; p_command_dma_loop: test SSTAT0, SDONE jnz p_command_ultra2_dma_done; test SSTAT1,PHASEMIS jz p_command_dma_loop; /* ie. underrun */ p_command_ultra2_dma_done: test SCSISIGI, REQI jz p_command_ultra2_shutdown; test SSTAT1, (PHASEMIS|REQINIT) jz p_command_ultra2_dma_done; p_command_ultra2_shutdown: and DFCNTRL, ~(HDMAEN|SCSIEN); test DFCNTRL, (HDMAEN|SCSIEN) jnz .; or SXFRCTL0, CLRSTCNT|CLRCHN; } jmp ITloop; /* * Status phase. Wait for the data byte to appear, then read it * and store it into the SCB. */ p_status: call assert; mov SCB_TARGET_STATUS, SCSIDATL; jmp ITloop; /* * Message out phase. If MSG_OUT is 0x80, build I full indentify message * sequence and send it to the target. In addition, if the MK_MESSAGE bit * is set in the SCB_CONTROL byte, interrupt the host and allow it to send * it's own message. * * If MSG_OUT is == HOST_MSG, also interrupt the host and take a message. * This is done to allow the hsot to send messages outside of an identify * sequence while protecting the seqencer from testing the MK_MESSAGE bit * on an SCB that might not be for the current nexus. (For example, a * BDR message in response to a bad reselection would leave us pointed to * an SCB that doesn't have anything to do with the current target). * Otherwise, treat MSG_OUT as a 1 byte message to send (abort, abort tag, * bus device reset). * * When there are no messages to send, MSG_OUT should be set to MSG_NOOP, * in case the target decides to put us in this phase for some strange * reason. */ p_mesgout_retry: or SCSISIGO,ATNO,LASTPHASE;/* turn on ATN for the retry */ p_mesgout: mov SINDEX, MSG_OUT; cmp SINDEX, MSG_IDENTIFYFLAG jne p_mesgout_from_host; p_mesgout_identify: if ((p->features & AHC_WIDE) != 0) { and SINDEX,0xf,SCB_TCL; /* lun */ } else { and SINDEX,0x7,SCB_TCL; /* lun */ } and A,DISCENB,SCB_CONTROL; /* mask off disconnect privilege */ or SINDEX,A; /* or in disconnect privilege */ or SINDEX,MSG_IDENTIFYFLAG; p_mesgout_mk_message: test SCB_CONTROL,MK_MESSAGE jz p_mesgout_tag; mov SCSIDATL, SINDEX; /* Send the last byte */ jmp p_mesgout_from_host + 1;/* Skip HOST_MSG test */ /* * Send a tag message if TAG_ENB is set in the SCB control block. * Use SCB_TAG (the position in the kernel's SCB array) as the tag value. */ p_mesgout_tag: test SCB_CONTROL,TAG_ENB jz p_mesgout_onebyte; mov SCSIDATL, SINDEX; /* Send the identify message */ call phase_lock; cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; and SCSIDATL,TAG_ENB|SCB_TAG_TYPE,SCB_CONTROL; call phase_lock; cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; mov SCB_TAG jmp p_mesgout_onebyte; /* * Interrupt the driver, and allow it to send a message * if it asks. */ p_mesgout_from_host: cmp SINDEX, HOST_MSG jne p_mesgout_onebyte; mvi INTSTAT,AWAITING_MSG; nop; /* * Did the host detect a phase change? */ cmp RETURN_1, MSGOUT_PHASEMIS je p_mesgout_done; p_mesgout_onebyte: mvi CLRSINT1, CLRATNO; mov SCSIDATL, SINDEX; /* * If the next bus phase after ATN drops is a message out, it means * that the target is requesting that the last message(s) be resent. */ call phase_lock; cmp LASTPHASE, P_MESGOUT je p_mesgout_retry; p_mesgout_done: mvi CLRSINT1,CLRATNO; /* Be sure to turn ATNO off */ mov LAST_MSG, MSG_OUT; cmp MSG_OUT, MSG_IDENTIFYFLAG jne . + 2; and SCB_CONTROL, ~MK_MESSAGE; mvi MSG_OUT, MSG_NOOP; /* No message left */ jmp ITloop; /* * Message in phase. Bytes are read using Automatic PIO mode. */ p_mesgin: mvi ACCUM call inb_first; /* read the 1st message byte */ test A,MSG_IDENTIFYFLAG jnz mesgin_identify; cmp A,MSG_DISCONNECT je mesgin_disconnect; cmp A,MSG_SAVEDATAPOINTER je mesgin_sdptrs; cmp ALLZEROS,A je mesgin_complete; cmp A,MSG_RESTOREPOINTERS je mesgin_rdptrs; cmp A,MSG_EXTENDED je mesgin_extended; cmp A,MSG_MESSAGE_REJECT je mesgin_reject; cmp A,MSG_NOOP je mesgin_done; cmp A,MSG_IGN_WIDE_RESIDUE je mesgin_wide_residue; rej_mesgin: /* * We have no idea what this message in is, so we issue a message reject * and hope for the best. In any case, rejection should be a rare * occurrence - signal the driver when it happens. */ mvi INTSTAT,SEND_REJECT; /* let driver know */ mvi MSG_MESSAGE_REJECT call mk_mesg; mesgin_done: mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ jmp ITloop; mesgin_complete: /* * We got a "command complete" message, so put the SCB_TAG into the QOUTFIFO, * and trigger a completion interrupt. Before doing so, check to see if there * is a residual or the status byte is something other than STATUS_GOOD (0). * In either of these conditions, we upload the SCB back to the host so it can * process this information. In the case of a non zero status byte, we * additionally interrupt the kernel driver synchronously, allowing it to * decide if sense should be retrieved. If the kernel driver wishes to request * sense, it will fill the kernel SCB with a request sense command and set * RETURN_1 to SEND_SENSE. If RETURN_1 is set to SEND_SENSE we redownload * the SCB, and process it as the next command by adding it to the waiting list. * If the kernel driver does not wish to request sense, it need only clear * RETURN_1, and the command is allowed to complete normally. We don't bother * to post to the QOUTFIFO in the error cases since it would require extra * work in the kernel driver to ensure that the entry was removed before the * command complete code tried processing it. */ /* * First check for residuals */ test SCB_RESID_SGCNT,0xff jnz upload_scb; test SCB_TARGET_STATUS,0xff jz complete; /* Good Status? */ upload_scb: mvi DMAPARAMS, FIFORESET; mov SCB_TAG call dma_scb; check_status: test SCB_TARGET_STATUS,0xff jz complete; /* Just a residual? */ mvi INTSTAT,BAD_STATUS; /* let driver know */ nop; cmp RETURN_1, SEND_SENSE jne complete; /* This SCB becomes the next to execute as it will retrieve sense */ mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; mov SCB_TAG call dma_scb; add_to_waiting_list: mov SCB_NEXT,WAITING_SCBH; mov WAITING_SCBH, SCBPTR; /* * Prepare our selection hardware before the busfree so we have a * high probability of winning arbitration. */ call start_selection; jmp await_busfree; complete: /* If we are untagged, clear our address up in host ram */ test SCB_CONTROL, TAG_ENB jnz complete_post; mov A, SAVED_TCL; mvi UNTAGGEDSCB_OFFSET call post_byte_setup; mvi SCB_LIST_NULL call post_byte; complete_post: /* Post the SCB and issue an interrupt */ if ((p->features & AHC_QUEUE_REGS) != 0) { mov A, SDSCB_QOFF; } else { mov A, QOUTPOS; } mvi QOUTFIFO_OFFSET call post_byte_setup; mov SCB_TAG call post_byte; if ((p->features & AHC_QUEUE_REGS) == 0) { inc QOUTPOS; } mvi INTSTAT,CMDCMPLT; add_to_free_list: call add_scb_to_free_list; jmp await_busfree; /* * Is it an extended message? Copy the message to our message buffer and * notify the host. The host will tell us whether to reject this message, * respond to it with the message that the host placed in our message buffer, * or simply to do nothing. */ mesgin_extended: mvi INTSTAT,EXTENDED_MSG; /* let driver know */ jmp ITloop; /* * Is it a disconnect message? Set a flag in the SCB to remind us * and await the bus going free. */ mesgin_disconnect: or SCB_CONTROL,DISCONNECTED; call add_scb_to_disc_list; jmp await_busfree; /* * Save data pointers message: * Copying RAM values back to SCB, for Save Data Pointers message, but * only if we've actually been into a data phase to change them. This * protects against bogus data in scratch ram and the residual counts * since they are only initialized when we go into data_in or data_out. */ mesgin_sdptrs: test SEQ_FLAGS, DPHASE jz mesgin_done; /* * The SCB SGPTR becomes the next one we'll download, * and the SCB DATAPTR becomes the current SHADDR. * Use the residual number since STCNT is corrupted by * any message transfer. */ if ((p->features & AHC_CMD_CHAN) != 0) { bmov SCB_SGCOUNT, SG_COUNT, 5; bmov SCB_DATAPTR, SHADDR, 4; bmov SCB_DATACNT, SCB_RESID_DCNT, 3; } else { mvi DINDEX, SCB_SGCOUNT; mvi SG_COUNT call bcopy_5; mvi DINDEX, SCB_DATAPTR; mvi SHADDR call bcopy_4; mvi SCB_RESID_DCNT call bcopy_3; } jmp mesgin_done; /* * Restore pointers message? Data pointers are recopied from the * SCB anytime we enter a data phase for the first time, so all * we need to do is clear the DPHASE flag and let the data phase * code do the rest. */ mesgin_rdptrs: and SEQ_FLAGS, ~DPHASE; /* * We'll reload them * the next time through * the dataphase. */ jmp mesgin_done; /* * Identify message? For a reconnecting target, this tells us the lun * that the reconnection is for - find the correct SCB and switch to it, * clearing the "disconnected" bit so we don't "find" it by accident later. */ mesgin_identify: if ((p->features & AHC_WIDE) != 0) { and A,0x0f; /* lun in lower four bits */ } else { and A,0x07; /* lun in lower three bits */ } or SAVED_TCL,A; /* SAVED_TCL should be complete now */ mvi ARG_2, SCB_LIST_NULL; /* SCBID of prev SCB in disc List */ call get_untagged_SCBID; cmp ARG_1, SCB_LIST_NULL je snoop_tag; if ((p->flags & AHC_PAGESCBS) != 0) { test SEQ_FLAGS, SCBPTR_VALID jz use_retrieveSCB; } /* * If the SCB was found in the disconnected list (as is * always the case in non-paging scenarios), SCBPTR is already * set to the correct SCB. So, simply setup the SCB and get * on with things. */ mov SCBPTR call rem_scb_from_disc_list; jmp setup_SCB; /* * Here we "snoop" the bus looking for a SIMPLE QUEUE TAG message. * If we get one, we use the tag returned to find the proper * SCB. With SCB paging, this requires using search for both tagged * and non-tagged transactions since the SCB may exist in any slot. * If we're not using SCB paging, we can use the tag as the direct * index to the SCB. */ snoop_tag: mov NONE,SCSIDATL; /* ACK Identify MSG */ snoop_tag_loop: call phase_lock; cmp LASTPHASE, P_MESGIN jne not_found; cmp SCSIBUSL,MSG_SIMPLE_Q_TAG jne not_found; get_tag: mvi ARG_1 call inb_next; /* tag value */ use_retrieveSCB: call retrieveSCB; setup_SCB: mov A, SAVED_TCL; cmp SCB_TCL, A jne not_found_cleanup_scb; test SCB_CONTROL,DISCONNECTED jz not_found_cleanup_scb; and SCB_CONTROL,~DISCONNECTED; or SEQ_FLAGS,IDENTIFY_SEEN; /* make note of IDENTIFY */ /* See if the host wants to send a message upon reconnection */ test SCB_CONTROL, MK_MESSAGE jz mesgin_done; and SCB_CONTROL, ~MK_MESSAGE; mvi HOST_MSG call mk_mesg; jmp mesgin_done; not_found_cleanup_scb: test SCB_CONTROL, DISCONNECTED jz . + 3; call add_scb_to_disc_list; jmp not_found; call add_scb_to_free_list; not_found: mvi INTSTAT, NO_MATCH; mvi MSG_BUS_DEV_RESET call mk_mesg; jmp mesgin_done; /* * Message reject? Let the kernel driver handle this. If we have an * outstanding WDTR or SDTR negotiation, assume that it's a response from * the target selecting 8bit or asynchronous transfer, otherwise just ignore * it since we have no clue what it pertains to. */ mesgin_reject: mvi INTSTAT, REJECT_MSG; jmp mesgin_done; /* * Wide Residue. We handle the simple cases, but pass of the one hard case * to the kernel (when the residue byte happened to cause us to advance our * sg element array, so we know have to back that advance out). */ mesgin_wide_residue: mvi ARG_1 call inb_next; /* ACK the wide_residue and get */ /* the size byte */ /* * In order for this to be reliable, we have to do all sorts of horrible * magic in terms of resetting the datafifo and reloading the shadow layer * with the correct new values (so that a subsequent save data pointers * message will do the right thing). We let the kernel do that work. */ mvi INTSTAT, WIDE_RESIDUE; jmp mesgin_done; /* * [ ADD MORE MESSAGE HANDLING HERE ] */ /* * Locking the driver out, build a one-byte message passed in SINDEX * if there is no active message already. SINDEX is returned intact. */ mk_mesg: or SCSISIGO,ATNO,LASTPHASE;/* turn on ATNO */ mov MSG_OUT,SINDEX ret; /* * Functions to read data in Automatic PIO mode. * * According to Adaptec's documentation, an ACK is not sent on input from * the target until SCSIDATL is read from. So we wait until SCSIDATL is * latched (the usual way), then read the data byte directly off the bus * using SCSIBUSL. When we have pulled the ATN line, or we just want to * acknowledge the byte, then we do a dummy read from SCISDATL. The SCSI * spec guarantees that the target will hold the data byte on the bus until * we send our ACK. * * The assumption here is that these are called in a particular sequence, * and that REQ is already set when inb_first is called. inb_{first,next} * use the same calling convention as inb. */ inb_next: mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ inb_next_wait: /* * If there is a parity error, wait for the kernel to * see the interrupt and prepare our message response * before continuing. */ test SSTAT1, REQINIT jz inb_next_wait; test SSTAT1, SCSIPERR jnz .; and LASTPHASE, PHASE_MASK, SCSISIGI; cmp LASTPHASE, P_MESGIN jne mesgin_phasemis; inb_first: mov DINDEX,SINDEX; mov DINDIR,SCSIBUSL ret; /*read byte directly from bus*/ inb_last: mov NONE,SCSIDATL ret; /*dummy read from latch to ACK*/ mesgin_phasemis: /* * We expected to receive another byte, but the target changed phase */ mvi INTSTAT, MSGIN_PHASEMIS; jmp ITloop; /* * DMA data transfer. HADDR and HCNT must be loaded first, and * SINDEX should contain the value to load DFCNTRL with - 0x3d for * host->scsi, or 0x39 for scsi->host. The SCSI channel is cleared * during initialization. */ if ((p->features & AHC_ULTRA2) == 0) { dma: mov DFCNTRL,SINDEX; dma_loop: test SSTAT0,DMADONE jnz dma_dmadone; test SSTAT1,PHASEMIS jz dma_loop; /* ie. underrun */ dma_phasemis: test SSTAT0,SDONE jnz dma_checkfifo; mov SINDEX,ALLZEROS; /* Notify caller of phasemiss */ /* * We will be "done" DMAing when the transfer count goes to zero, or * the target changes the phase (in light of this, it makes sense that * the DMA circuitry doesn't ACK when PHASEMIS is active). If we are * doing a SCSI->Host transfer, the data FIFO should be flushed auto- * magically on STCNT=0 or a phase change, so just wait for FIFO empty * status. */ dma_checkfifo: test DFCNTRL,DIRECTION jnz dma_fifoempty; dma_fifoflush: test DFSTATUS,FIFOEMP jz dma_fifoflush; dma_fifoempty: /* Don't clobber an inprogress host data transfer */ test DFSTATUS, MREQPEND jnz dma_fifoempty; /* * Now shut the DMA enables off and make sure that the DMA enables are * actually off first lest we get an ILLSADDR. */ dma_dmadone: cmp LASTPHASE, P_COMMAND je dma_await_nreq; test SCSIRATE, 0x0f jnz dma_shutdown; dma_await_nreq: test SCSISIGI, REQI jz dma_shutdown; test SSTAT1, (PHASEMIS|REQINIT) jz dma_await_nreq; dma_shutdown: and DFCNTRL, ~(SCSIEN|SDMAEN|HDMAEN); dma_halt: /* * Some revisions of the aic7880 have a problem where, if the * data fifo is full, but the PCI input latch is not empty, * HDMAEN cannot be cleared. The fix used here is to attempt * to drain the data fifo until there is space for the input * latch to drain and HDMAEN de-asserts. */ if ((p->bugs & AHC_BUG_PCI_2_1_RETRY) != 0) { mov NONE, DFDAT; } test DFCNTRL, (SCSIEN|SDMAEN|HDMAEN) jnz dma_halt; } return: ret; /* * Assert that if we've been reselected, then we've seen an IDENTIFY * message. */ assert: test SEQ_FLAGS,IDENTIFY_SEEN jnz return; /* seen IDENTIFY? */ mvi INTSTAT,NO_IDENT ret; /* no - tell the kernel */ /* * Locate a disconnected SCB either by SAVED_TCL (ARG_1 is SCB_LIST_NULL) * or by the SCBID ARG_1. The search begins at the SCB index passed in * via SINDEX which is an SCB that must be on the disconnected list. If * the SCB cannot be found, SINDEX will be SCB_LIST_NULL, otherwise, SCBPTR * is set to the proper SCB. */ findSCB: mov SCBPTR,SINDEX; /* Initialize SCBPTR */ cmp ARG_1, SCB_LIST_NULL jne findSCB_by_SCBID; mov A, SAVED_TCL; mvi SCB_TCL jmp findSCB_loop; /* &SCB_TCL -> SINDEX */ findSCB_by_SCBID: mov A, ARG_1; /* Tag passed in ARG_1 */ mvi SCB_TAG jmp findSCB_loop; /* &SCB_TAG -> SINDEX */ findSCB_next: mov ARG_2, SCBPTR; cmp SCB_NEXT, SCB_LIST_NULL je notFound; mov SCBPTR,SCB_NEXT; dec SINDEX; /* Last comparison moved us too far */ findSCB_loop: cmp SINDIR, A jne findSCB_next; mov SINDEX, SCBPTR ret; notFound: mvi SINDEX, SCB_LIST_NULL ret; /* * Retrieve an SCB by SCBID first searching the disconnected list falling * back to DMA'ing the SCB down from the host. This routine assumes that * ARG_1 is the SCBID of interest and that SINDEX is the position in the * disconnected list to start the search from. If SINDEX is SCB_LIST_NULL, * we go directly to the host for the SCB. */ retrieveSCB: test SEQ_FLAGS, SCBPTR_VALID jz retrieve_from_host; mov SCBPTR call findSCB; /* Continue the search */ cmp SINDEX, SCB_LIST_NULL je retrieve_from_host; /* * This routine expects SINDEX to contain the index of the SCB to be * removed, SCBPTR to be pointing to that SCB, and ARG_2 to be the * SCBID of the SCB just previous to this one in the list or SCB_LIST_NULL * if it is at the head. */ rem_scb_from_disc_list: /* Remove this SCB from the disconnection list */ cmp ARG_2, SCB_LIST_NULL je rHead; mov DINDEX, SCB_NEXT; mov SCBPTR, ARG_2; mov SCB_NEXT, DINDEX; mov SCBPTR, SINDEX ret; rHead: mov DISCONNECTED_SCBH,SCB_NEXT ret; retrieve_from_host: /* * We didn't find it. Pull an SCB and DMA down the one we want. * We should never get here in the non-paging case. */ mov ALLZEROS call get_free_or_disc_scb; mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; /* Jump instead of call as we want to return anyway */ mov ARG_1 jmp dma_scb; /* * Determine whether a target is using tagged or non-tagged transactions * by first looking for a matching transaction based on the TCL and if * that fails, looking up this device in the host's untagged SCB array. * The TCL to search for is assumed to be in SAVED_TCL. The value is * returned in ARG_1 (SCB_LIST_NULL for tagged, SCBID for non-tagged). * The SCBPTR_VALID bit is set in SEQ_FLAGS if we found the information * in an SCB instead of having to go to the host. */ get_untagged_SCBID: cmp DISCONNECTED_SCBH, SCB_LIST_NULL je get_SCBID_from_host; mvi ARG_1, SCB_LIST_NULL; mov DISCONNECTED_SCBH call findSCB; cmp SINDEX, SCB_LIST_NULL je get_SCBID_from_host; or SEQ_FLAGS, SCBPTR_VALID;/* Was in disconnected list */ test SCB_CONTROL, TAG_ENB jnz . + 2; mov ARG_1, SCB_TAG ret; mvi ARG_1, SCB_LIST_NULL ret; /* * Fetch a byte from host memory given an index of (A + (256 * SINDEX)) * and a base address of SCBID_ADDR. The byte is returned in RETURN_2. */ fetch_byte: mov ARG_2, SINDEX; if ((p->features & AHC_CMD_CHAN) != 0) { mvi DINDEX, CCHADDR; mvi SCBID_ADDR call set_1byte_addr; mvi CCHCNT, 1; mvi CCSGCTL, CCSGEN|CCSGRESET; test CCSGCTL, CCSGDONE jz .; mvi CCSGCTL, CCSGRESET; bmov RETURN_2, CCSGRAM, 1 ret; } else { mvi DINDEX, HADDR; mvi SCBID_ADDR call set_1byte_addr; mvi HCNT[0], 1; clr HCNT[1]; clr HCNT[2]; mvi DFCNTRL, HDMAEN|DIRECTION|FIFORESET; call dma_finish; mov RETURN_2, DFDAT ret; } /* * Prepare the hardware to post a byte to host memory given an * index of (A + (256 * SINDEX)) and a base address of SCBID_ADDR. */ post_byte_setup: mov ARG_2, SINDEX; if ((p->features & AHC_CMD_CHAN) != 0) { mvi DINDEX, CCHADDR; mvi SCBID_ADDR call set_1byte_addr; mvi CCHCNT, 1; mvi CCSCBCTL, CCSCBRESET ret; } else { mvi DINDEX, HADDR; mvi SCBID_ADDR call set_1byte_addr; mvi HCNT[0], 1; clr HCNT[1]; clr HCNT[2]; mvi DFCNTRL, FIFORESET ret; } post_byte: if ((p->features & AHC_CMD_CHAN) != 0) { bmov CCSCBRAM, SINDEX, 1; or CCSCBCTL, CCSCBEN|CCSCBRESET; test CCSCBCTL, CCSCBDONE jz .; clr CCSCBCTL ret; } else { mov DFDAT, SINDEX; or DFCNTRL, HDMAEN|FIFOFLUSH; jmp dma_finish; } get_SCBID_from_host: mov A, SAVED_TCL; mvi UNTAGGEDSCB_OFFSET call fetch_byte; mov RETURN_1, RETURN_2 ret; phase_lock: test SSTAT1, REQINIT jz phase_lock; test SSTAT1, SCSIPERR jnz phase_lock; and SCSISIGO, PHASE_MASK, SCSISIGI; and LASTPHASE, PHASE_MASK, SCSISIGI ret; if ((p->features & AHC_CMD_CHAN) == 0) { set_stcnt_from_hcnt: mov STCNT[0], HCNT[0]; mov STCNT[1], HCNT[1]; mov STCNT[2], HCNT[2] ret; bcopy_7: mov DINDIR, SINDIR; mov DINDIR, SINDIR; bcopy_5: mov DINDIR, SINDIR; bcopy_4: mov DINDIR, SINDIR; bcopy_3: mov DINDIR, SINDIR; mov DINDIR, SINDIR; mov DINDIR, SINDIR ret; } /* * Setup addr assuming that A is an index into * an array of 32byte objects, SINDEX contains * the base address of that array, and DINDEX * contains the base address of the location * to store the indexed address. */ set_32byte_addr: shr ARG_2, 3, A; shl A, 5; /* * Setup addr assuming that A + (ARG_1 * 256) is an * index into an array of 1byte objects, SINDEX contains * the base address of that array, and DINDEX contains * the base address of the location to store the computed * address. */ set_1byte_addr: add DINDIR, A, SINDIR; mov A, ARG_2; adc DINDIR, A, SINDIR; clr A; adc DINDIR, A, SINDIR; adc DINDIR, A, SINDIR ret; /* * Either post or fetch and SCB from host memory based on the * DIRECTION bit in DMAPARAMS. The host SCB index is in SINDEX. */ dma_scb: mov A, SINDEX; if ((p->features & AHC_CMD_CHAN) != 0) { mvi DINDEX, CCHADDR; mvi HSCB_ADDR call set_32byte_addr; mov CCSCBPTR, SCBPTR; mvi CCHCNT, 32; test DMAPARAMS, DIRECTION jz dma_scb_tohost; mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBDIR|CCSCBRESET; cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN|CCSCBDIR jne .; jmp dma_scb_finish; dma_scb_tohost: if ((p->features & AHC_ULTRA2) == 0) { mvi CCSCBCTL, CCSCBRESET; bmov CCSCBRAM, SCB_CONTROL, 32; or CCSCBCTL, CCSCBEN|CCSCBRESET; test CCSCBCTL, CCSCBDONE jz .; } if ((p->features & AHC_ULTRA2) != 0) { if ((p->bugs & AHC_BUG_SCBCHAN_UPLOAD) != 0) { mvi CCSCBCTL, CCARREN|CCSCBRESET; cmp CCSCBCTL, ARRDONE|CCARREN jne .; mvi CCHCNT, 32; mvi CCSCBCTL, CCSCBEN|CCSCBRESET; cmp CCSCBCTL, CCSCBDONE|CCSCBEN jne .; } else { mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBRESET; cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN jne .; } } dma_scb_finish: clr CCSCBCTL; test CCSCBCTL, CCARREN|CCSCBEN jnz .; ret; } if ((p->features & AHC_CMD_CHAN) == 0) { mvi DINDEX, HADDR; mvi HSCB_ADDR call set_32byte_addr; mvi HCNT[0], 32; clr HCNT[1]; clr HCNT[2]; mov DFCNTRL, DMAPARAMS; test DMAPARAMS, DIRECTION jnz dma_scb_fromhost; /* Fill it with the SCB data */ copy_scb_tofifo: mvi SINDEX, SCB_CONTROL; add A, 32, SINDEX; copy_scb_tofifo_loop: mov DFDAT,SINDIR; mov DFDAT,SINDIR; mov DFDAT,SINDIR; mov DFDAT,SINDIR; mov DFDAT,SINDIR; mov DFDAT,SINDIR; mov DFDAT,SINDIR; mov DFDAT,SINDIR; cmp SINDEX, A jne copy_scb_tofifo_loop; or DFCNTRL, HDMAEN|FIFOFLUSH; jmp dma_finish; dma_scb_fromhost: mvi DINDEX, SCB_CONTROL; if ((p->bugs & AHC_BUG_PCI_2_1_RETRY) != 0) { /* * Set the A to -24. It it hits 0, then we let * our code fall through to dfdat_in_8 to complete * the last of the copy. * * Also, things happen 8 bytes at a time in this * case, so we may need to drain the fifo at most * 3 times to keep things flowing */ mvi A, -24; dma_scb_hang_fifo: /* Wait for the first bit of data to hit the fifo */ test DFSTATUS, FIFOEMP jnz .; dma_scb_hang_wait: /* OK, now they've started to transfer into the fifo, * so wait for them to stop trying to transfer any * more data. */ test DFSTATUS, MREQPEND jnz .; /* * OK, they started, then they stopped, now see if they * managed to complete the job before stopping. Try * it multiple times to give the chip a few cycles to * set the flag if it did complete. */ test DFSTATUS, HDONE jnz dma_scb_hang_dma_done; test DFSTATUS, HDONE jnz dma_scb_hang_dma_done; test DFSTATUS, HDONE jnz dma_scb_hang_dma_done; /* * Too bad, the chip didn't complete the DMA, but there * aren't any more memory requests pending, so that * means it stopped part way through and hung. That's * our bug, so now we drain what data there is in the * fifo in order to get things going again. */ dma_scb_hang_empty_fifo: call dfdat_in_8; add A, 8; add SINDEX, A, HCNT; /* * If there are another 8 bytes of data waiting in the * fifo, then the carry bit will be set as a result * of the above add command (unless A is non-negative, * in which case the carry bit won't be set). */ jc dma_scb_hang_empty_fifo; /* * We've emptied the fifo now, but we wouldn't have got * here if the memory transfer hadn't stopped part way * through, so go back up to the beginning of the * loop and start over. When it succeeds in getting * all the data down, HDONE will be set and we'll * jump to the code just below here. */ jmp dma_scb_hang_fifo; dma_scb_hang_dma_done: and DFCNTRL, ~HDMAEN; test DFCNTRL, HDMAEN jnz .; call dfdat_in_8; add A, 8; cmp A, 8 jne . - 2; ret; } else { call dma_finish; call dfdat_in_8; call dfdat_in_8; call dfdat_in_8; } dfdat_in_8: mov DINDIR,DFDAT; dfdat_in_7: mov DINDIR,DFDAT; mov DINDIR,DFDAT; mov DINDIR,DFDAT; mov DINDIR,DFDAT; mov DINDIR,DFDAT; mov DINDIR,DFDAT; mov DINDIR,DFDAT ret; } /* * Wait for DMA from host memory to data FIFO to complete, then disable * DMA and wait for it to acknowledge that it's off. */ if ((p->features & AHC_CMD_CHAN) == 0) { dma_finish: test DFSTATUS,HDONE jz dma_finish; /* Turn off DMA */ and DFCNTRL, ~HDMAEN; test DFCNTRL, HDMAEN jnz .; ret; } add_scb_to_free_list: if ((p->flags & AHC_PAGESCBS) != 0) { mov SCB_NEXT, FREE_SCBH; mov FREE_SCBH, SCBPTR; } mvi SCB_TAG, SCB_LIST_NULL ret; if ((p->flags & AHC_PAGESCBS) != 0) { get_free_or_disc_scb: cmp FREE_SCBH, SCB_LIST_NULL jne dequeue_free_scb; cmp DISCONNECTED_SCBH, SCB_LIST_NULL jne dequeue_disc_scb; return_error: mvi SINDEX, SCB_LIST_NULL ret; dequeue_disc_scb: mov SCBPTR, DISCONNECTED_SCBH; dma_up_scb: mvi DMAPARAMS, FIFORESET; mov SCB_TAG call dma_scb; unlink_disc_scb: mov DISCONNECTED_SCBH, SCB_NEXT ret; dequeue_free_scb: mov SCBPTR, FREE_SCBH; mov FREE_SCBH, SCB_NEXT ret; } add_scb_to_disc_list: /* * Link this SCB into the DISCONNECTED list. This list holds the * candidates for paging out an SCB if one is needed for a new command. * Modifying the disconnected list is a critical(pause dissabled) section. */ mov SCB_NEXT, DISCONNECTED_SCBH; mov DISCONNECTED_SCBH, SCBPTR ret;