/* * intel TCO vendor specific watchdog driver support * * (c) Copyright 2006-2009 Wim Van Sebroeck . * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. * * Neither Wim Van Sebroeck nor Iguana vzw. admit liability nor * provide warranty for any of this software. This material is * provided "AS-IS" and at no charge. */ /* * Includes, defines, variables, module parameters, ... */ /* Module and version information */ #define DRV_NAME "iTCO_vendor_support" #define DRV_VERSION "1.04" #define PFX DRV_NAME ": " /* Includes */ #include /* For module specific items */ #include /* For new moduleparam's */ #include /* For standard types (like size_t) */ #include /* For the -ENODEV/... values */ #include /* For printk/panic/... */ #include /* For __init/__exit/... */ #include /* For io-port access */ #include /* For inb/outb/... */ #include "iTCO_vendor.h" /* iTCO defines */ #define SMI_EN (acpibase + 0x30) /* SMI Control and Enable Register */ #define TCOBASE (acpibase + 0x60) /* TCO base address */ #define TCO1_STS (TCOBASE + 0x04) /* TCO1 Status Register */ /* List of vendor support modes */ /* SuperMicro Pentium 3 Era 370SSE+-OEM1/P3TSSE */ #define SUPERMICRO_OLD_BOARD 1 /* SuperMicro Pentium 4 / Xeon 4 / EMT64T Era Systems */ #define SUPERMICRO_NEW_BOARD 2 /* Broken BIOS */ #define BROKEN_BIOS 911 static int vendorsupport; module_param(vendorsupport, int, 0); MODULE_PARM_DESC(vendorsupport, "iTCO vendor specific support mode, default=" "0 (none), 1=SuperMicro Pent3, 2=SuperMicro Pent4+, " "911=Broken SMI BIOS"); /* * Vendor Specific Support */ /* * Vendor Support: 1 * Board: Super Micro Computer Inc. 370SSE+-OEM1/P3TSSE * iTCO chipset: ICH2 * * Code contributed by: R. Seretny * Documentation obtained by R. Seretny from SuperMicro Technical Support * * To enable Watchdog function: * BIOS setup -> Power -> TCO Logic SMI Enable -> Within5Minutes * This setting enables SMI to clear the watchdog expired flag. * If BIOS or CPU fail which may cause SMI hang, then system will * reboot. When application starts to use watchdog function, * application has to take over the control from SMI. * * For P3TSSE, J36 jumper needs to be removed to enable the Watchdog * function. * * Note: The system will reboot when Expire Flag is set TWICE. * So, if the watchdog timer is 20 seconds, then the maximum hang * time is about 40 seconds, and the minimum hang time is about * 20.6 seconds. */ static void supermicro_old_pre_start(unsigned long acpibase) { unsigned long val32; /* Bit 13: TCO_EN -> 0 = Disables TCO logic generating an SMI# */ val32 = inl(SMI_EN); val32 &= 0xffffdfff; /* Turn off SMI clearing watchdog */ outl(val32, SMI_EN); /* Needed to activate watchdog */ } static void supermicro_old_pre_stop(unsigned long acpibase) { unsigned long val32; /* Bit 13: TCO_EN -> 1 = Enables the TCO logic to generate SMI# */ val32 = inl(SMI_EN); val32 |= 0x00002000; /* Turn on SMI clearing watchdog */ outl(val32, SMI_EN); /* Needed to deactivate watchdog */ } /* * Vendor Support: 2 * Board: Super Micro Computer Inc. P4SBx, P4DPx * iTCO chipset: ICH4 * * Code contributed by: R. Seretny * Documentation obtained by R. Seretny from SuperMicro Technical Support * * To enable Watchdog function: * 1. BIOS * For P4SBx: * BIOS setup -> Advanced -> Integrated Peripherals -> Watch Dog Feature * For P4DPx: * BIOS setup -> Advanced -> I/O Device Configuration -> Watch Dog * This setting enables or disables Watchdog function. When enabled, the * default watchdog timer is set to be 5 minutes (about 4m35s). It is * enough to load and run the OS. The application (service or driver) has * to take over the control once OS is running up and before watchdog * expires. * * 2. JUMPER * For P4SBx: JP39 * For P4DPx: JP37 * This jumper is used for safety. Closed is enabled. This jumper * prevents user enables watchdog in BIOS by accident. * * To enable Watch Dog function, both BIOS and JUMPER must be enabled. * * The documentation lists motherboards P4SBx and P4DPx series as of * 20-March-2002. However, this code works flawlessly with much newer * motherboards, such as my X6DHR-8G2 (SuperServer 6014H-82). * * The original iTCO driver as written does not actually reset the * watchdog timer on these machines, as a result they reboot after five * minutes. * * NOTE: You may leave the Watchdog function disabled in the SuperMicro * BIOS to avoid a "boot-race"... This driver will enable watchdog * functionality even if it's disabled in the BIOS once the /dev/watchdog * file is opened. */ /* I/O Port's */ #define SM_REGINDEX 0x2e /* SuperMicro ICH4+ Register Index */ #define SM_DATAIO 0x2f /* SuperMicro ICH4+ Register Data I/O */ /* Control Register's */ #define SM_CTLPAGESW 0x07 /* SuperMicro ICH4+ Control Page Switch */ #define SM_CTLPAGE 0x08 /* SuperMicro ICH4+ Control Page Num */ #define SM_WATCHENABLE 0x30 /* Watchdog enable: Bit 0: 0=off, 1=on */ #define SM_WATCHPAGE 0x87 /* Watchdog unlock control page */ #define SM_ENDWATCH 0xAA /* Watchdog lock control page */ #define SM_COUNTMODE 0xf5 /* Watchdog count mode select */ /* (Bit 3: 0 = seconds, 1 = minutes */ #define SM_WATCHTIMER 0xf6 /* 8-bits, Watchdog timer counter (RW) */ #define SM_RESETCONTROL 0xf7 /* Watchdog reset control */ /* Bit 6: timer is reset by kbd interrupt */ /* Bit 7: timer is reset by mouse interrupt */ static void supermicro_new_unlock_watchdog(void) { /* Write 0x87 to port 0x2e twice */ outb(SM_WATCHPAGE, SM_REGINDEX); outb(SM_WATCHPAGE, SM_REGINDEX); /* Switch to watchdog control page */ outb(SM_CTLPAGESW, SM_REGINDEX); outb(SM_CTLPAGE, SM_DATAIO); } static void supermicro_new_lock_watchdog(void) { outb(SM_ENDWATCH, SM_REGINDEX); } static void supermicro_new_pre_start(unsigned int heartbeat) { unsigned int val; supermicro_new_unlock_watchdog(); /* Watchdog timer setting needs to be in seconds*/ outb(SM_COUNTMODE, SM_REGINDEX); val = inb(SM_DATAIO); val &= 0xF7; outb(val, SM_DATAIO); /* Write heartbeat interval to WDOG */ outb(SM_WATCHTIMER, SM_REGINDEX); outb((heartbeat & 255), SM_DATAIO); /* Make sure keyboard/mouse interrupts don't interfere */ outb(SM_RESETCONTROL, SM_REGINDEX); val = inb(SM_DATAIO); val &= 0x3f; outb(val, SM_DATAIO); /* enable watchdog by setting bit 0 of Watchdog Enable to 1 */ outb(SM_WATCHENABLE, SM_REGINDEX); val = inb(SM_DATAIO); val |= 0x01; outb(val, SM_DATAIO); supermicro_new_lock_watchdog(); } static void supermicro_new_pre_stop(void) { unsigned int val; supermicro_new_unlock_watchdog(); /* disable watchdog by setting bit 0 of Watchdog Enable to 0 */ outb(SM_WATCHENABLE, SM_REGINDEX); val = inb(SM_DATAIO); val &= 0xFE; outb(val, SM_DATAIO); supermicro_new_lock_watchdog(); } static void supermicro_new_pre_set_heartbeat(unsigned int heartbeat) { supermicro_new_unlock_watchdog(); /* reset watchdog timeout to heartveat value */ outb(SM_WATCHTIMER, SM_REGINDEX); outb((heartbeat & 255), SM_DATAIO); supermicro_new_lock_watchdog(); } /* * Vendor Support: 911 * Board: Some Intel ICHx based motherboards * iTCO chipset: ICH7+ * * Some Intel motherboards have a broken BIOS implementation: i.e. * the SMI handler clear's the TIMEOUT bit in the TC01_STS register * and does not reload the time. Thus the TCO watchdog does not reboot * the system. * * These are the conclusions of Andriy Gapon after * debugging: the SMI handler is quite simple - it tests value in * TCO1_CNT against 0x800, i.e. checks TCO_TMR_HLT. If the bit is set * the handler goes into an infinite loop, apparently to allow the * second timeout and reboot. Otherwise it simply clears TIMEOUT bit * in TCO1_STS and that's it. * So the logic seems to be reversed, because it is hard to see how * TIMEOUT can get set to 1 and SMI generated when TCO_TMR_HLT is set * (other than a transitional effect). * * The only fix found to get the motherboard(s) to reboot is to put * the glb_smi_en bit to 0. This is a dirty hack that bypasses the * broken code by disabling Global SMI. * * WARNING: globally disabling SMI could possibly lead to dramatic * problems, especially on laptops! I.e. various ACPI things where * SMI is used for communication between OS and firmware. * * Don't use this fix if you don't need to!!! */ static void broken_bios_start(unsigned long acpibase) { unsigned long val32; val32 = inl(SMI_EN); /* Bit 13: TCO_EN -> 0 = Disables TCO logic generating an SMI# Bit 0: GBL_SMI_EN -> 0 = No SMI# will be generated by ICH. */ val32 &= 0xffffdffe; outl(val32, SMI_EN); } static void broken_bios_stop(unsigned long acpibase) { unsigned long val32; val32 = inl(SMI_EN); /* Bit 13: TCO_EN -> 1 = Enables TCO logic generating an SMI# Bit 0: GBL_SMI_EN -> 1 = Turn global SMI on again. */ val32 |= 0x00002001; outl(val32, SMI_EN); } /* * Generic Support Functions */ void iTCO_vendor_pre_start(unsigned long acpibase, unsigned int heartbeat) { switch (vendorsupport) { case SUPERMICRO_OLD_BOARD: supermicro_old_pre_start(acpibase); break; case SUPERMICRO_NEW_BOARD: supermicro_new_pre_start(heartbeat); break; case BROKEN_BIOS: broken_bios_start(acpibase); break; } } EXPORT_SYMBOL(iTCO_vendor_pre_start); void iTCO_vendor_pre_stop(unsigned long acpibase) { switch (vendorsupport) { case SUPERMICRO_OLD_BOARD: supermicro_old_pre_stop(acpibase); break; case SUPERMICRO_NEW_BOARD: supermicro_new_pre_stop(); break; case BROKEN_BIOS: broken_bios_stop(acpibase); break; } } EXPORT_SYMBOL(iTCO_vendor_pre_stop); void iTCO_vendor_pre_keepalive(unsigned long acpibase, unsigned int heartbeat) { if (vendorsupport == SUPERMICRO_NEW_BOARD) supermicro_new_pre_set_heartbeat(heartbeat); } EXPORT_SYMBOL(iTCO_vendor_pre_keepalive); void iTCO_vendor_pre_set_heartbeat(unsigned int heartbeat) { if (vendorsupport == SUPERMICRO_NEW_BOARD) supermicro_new_pre_set_heartbeat(heartbeat); } EXPORT_SYMBOL(iTCO_vendor_pre_set_heartbeat); int iTCO_vendor_check_noreboot_on(void) { switch (vendorsupport) { case SUPERMICRO_OLD_BOARD: return 0; default: return 1; } } EXPORT_SYMBOL(iTCO_vendor_check_noreboot_on); static int __init iTCO_vendor_init_module(void) { printk(KERN_INFO PFX "vendor-support=%d\n", vendorsupport); return 0; } static void __exit iTCO_vendor_exit_module(void) { printk(KERN_INFO PFX "Module Unloaded\n"); } module_init(iTCO_vendor_init_module); module_exit(iTCO_vendor_exit_module); MODULE_AUTHOR("Wim Van Sebroeck , " "R. Seretny "); MODULE_DESCRIPTION("Intel TCO Vendor Specific WatchDog Timer Driver Support"); MODULE_VERSION(DRV_VERSION); MODULE_LICENSE("GPL");